Fractional factorial design optimization of the separation of pilocarpine and its degradation products by capillary electrophoresis

The separation of pilocarpine and its degradation products by micellar electrokinetic capillary chromatography (MECC) has been optimized by using fractional factorial design of the experiments. Critical parameters were identified in a screening design, and an optimization design was used to optimize the separation. The optimal separation method was based on a borate buffer with sodium dodecyl sulfate (SDS). It is concluded that by using fractional factorial design it is possible to improve the separation of pilocarpine, it trans epimer, isopilocarpine and their hydrolysis products, pilocarpic acid and isopilocarpic acid.     

Determination of the anticancer drug prospidin in human tissue by high-performance capillary electrophoresis using derivatization

A high-performance capillary electrophoresis (HPCE) method is described for the quantitative determination of the anticancer drug prospidin in human tissue after its derivatization with diethyldithiocarbamic acid sodium salt (DDTC). It was found that absorption of prospidin and its derivatives on the capillary wall due to the strong positive charge in the drug molecules could be eliminated by increasing the methanol content in the run buffer up to 50% and increasing the pH value up to 11.2. While studying the conditions of the interaction between prospidin and DDTC, a molar excess of the latter of 1:9 and 1.5 h of reaction time were found to be enough for complete derivatization. Sample preparation included homogenization of freshly cut papilloma species and deproteinization by methanol addition. Detection was by ultraviolet (UV) absorption at 254 nm. Due to its speed and high performance in separation. Detection was by ultraviolet (UV) absorption at 254 mm. Due to its speed and high practice.     

Analysis of the antidiabetic drug acarbose by capillary electrophoresis

This study describes the derivatization of the pseudooligosaccharide acarbose and its main metabolite, component 2, with 7-aminonaphthalene-1,3-disulfonic acid (ANDS) in human urine. Their efficient separation was possible by means of capillary zone electrophoresis, using a capillary tube of fused-silica containing 100 mM triethylammonium phosphate buffer, pH 1.5. On column laser-induced fluorescence allowed the detection of the pseudooligosaccharides in human urine in the nanomolar range. With this method, acarbose and component 2 were quantified in human urine after application of 300 mg of acarbose.     

Determination of opiates in urine by capillary electrophoresis

A method for the separation of a mixture of opiates comprising pholcodine, 6-monoacetylmorphine, morphine, heroin, codeine and dihydrocodeine by capillary electrophoresis using a running buffer of 100 mM disodium hydrogenphosphate at pH 6 is described. The characteristics of an analytical method based on this separation for the determination of these drugs following extraction from urine and using levallorphan as internal standard are reported. Detection limits in the region of 10 ng cm⁻³ are achieved when using electrokinetic injection. A comparison is made of the sensitivity and reproducibility of electrokinetic and hydrodynamic injection for these drugs. Data are presented to show the results obtained when the proposed method is applied to urine spiked with all the above opiates and also to urine from a subject following consumption of dihydrocodeine and pholcodine. The concentrations found are compared with those obtained by LC.     

Determination of gabapentin in serum by capillary electrophoresis

A rapid capillary electrophoresis method for the quantification of gabapentin, a new anticonvulsant drug, in serum was developed. The assay involves derivatization of gabapentin with fluorescamine to provide a chromophore for UV-fluorescence detection. The migration time is about 11 min. The assay was linear between 0 and 20 mg/l. No other therapeutic drugs or amino acids interfered with the gabapentin peak. The relative standard deviation is 2.4% at a mean 11 mg/l (n=17). The mean serum level for 52 patients on this drug was 5.2 mg/l with a range of 0–12 mg/l.     

Evaluation of microbial proteolysis in meat products by capillary electrophoresis

AIMS: The available methods for evaluating proteolysis in meat products, particularly the contribution of micro-organisms, are expensive, time-consuming and require an unacceptable sample size. To minimize these problems, two capillary electrophoresis-based methods have been developed. METHODS AND RESULTS: Six Gram-positive, catalase-positive cocci, four moulds and three yeasts, isolated from dry-cured ham, were tested on sterile pork slices. Using the Capillary Gel Electrophoresis (CGE) method, changes in sarcoplasmic and myofibrillar proteins due to endogenous and microbial enzymes were detected. The Capillary Zone Electrophoresis (CZE) analysis allowed evaluation of bulk changes by micro-organisms in soluble nitrogen compounds. CONCLUSION: CGE analysis of myofibrillar proteins and CZE determination of soluble nitrogen compounds have proved to be valuable tools for evaluating proteolytic activity of endogenous and microbial origin. SIGNIFICANCE AND IMPACT OF THE STUDY: The CGE and CZE methods developed can be used for a rapid and sensitive analysis of proteolysis in meat products.     

Determination of idarubicin and idarubicinol in plasma by capillary electrophoresis

A rapid and sensitive capillary electrophoretic method for the determination of idarubicin and its metabolite idarubicinol in plasma has been developed and validated. Plasma is extracted by liquid-liquid extraction using chloroform. Idarubicin, idarubicinol and the internal standard daunorubicin can be separated in less than 5 min using a phosphate buffer of pH 5 with 70% acetonitrile. Laser-induced fluorescence detection with an Ar ion laser operated at 488 nm provides a sensitive and selective detection method without interferences from biological fluids. The small sample volume of 100 μl is of particular advantage for studies in pediatric oncology. The reproducibility of the method has been shown to be sufficient for drug monitoring or pharmacokinetic studies. The limit of quantification for idarubicin in plasma is 0.5 ng/ml.     

Determination of meningococcal polysaccharides by capillary zone electrophoresis

Meningococcal polysaccharides are medically important molecules and are the active components of vaccines against Neisseria meningiditis serogroups A, C, W135, and Y. This study demonstrates that free solution capillary zone electrophoresis (CZE) using simple phosphate/borate separation buffers is capable of separating intact, native polysaccharides from these four serogroups. Separation appeared to be robust with respect to variations in test conditions and behaved in expected ways with respect to changes in temperature, ionic strength, and addition of an organic modifier. Serogroups W135 and Y are composed of sialic acid residues alternating with either galactose or glucose, respectively. Separation of these serogroups could be achieved using phosphate buffer and was therefore not dependent on differential complexation with borate. Addition of sodium dodecyl sulfate to the separation buffer (i.e., MEKC) resulted in peak splitting for all four serogroups. Changes in polysaccharide size did not affect migration time for the size range examined, but serogroup C polysaccharide (a sialic acid homopolymer) was separable from sialic acid monosaccharide. CZE quantification of multiple lots of each of the four serogroups was compared to wet chemical determination by phosphorus or sialic acid measurement. Results from CZE determination showed good agreement with the wet chemical methods.     

尿样中三种蛋白质的毛细管电泳分离检测方法研究

目的:建立毛细管电泳分离测定人尿样中转铁蛋白、白蛋白和血红蛋白的新方法.方法:通过选择运行缓冲溶液种类及浓度、pH、表面活性荆种类及浓度、分离电压、进样时间对蛋白质分离效果的影响,优化了毛细管电泳法分离转铁蛋白、白蛋白和血红蛋白的条件.结果:利用此方法测定三种蛋白质的含量,浓度在0.01到1.00 g L-1范围内与峰电流呈良好的线性关系,检出限均为10-4 g L-1.结论:所建立的方法用于人尿样中转铁蛋白、白蛋白和血红蛋白的测定,结果满意.     

Determination of amoxicillin in plasma samples by capillary electrophoresis

We have developed a capillary zone electrophoresis (CZE) method for determining amoxicillin in animal plasma samples. Sample clean-up involved solid-phase extraction onto Sep-Pak C₁₈ cartridges followed by elution with water–methanol (85:15). This paper describes two different techniques to increase the sensitivity of the CZE method: field-amplified sample injection (FASI) and electrokinetic injection. We have enhanced the detection limit to 280 μg l⁻¹ by the FASI technique.     

Determination of grepafloxacin and clinafloxacin by capillary zone electrophoresis

A simple and rapid capillary zone electrophoresis determination method with UV detection of grepafloxacin and clinafloxacin has been developed. The separation was performed in 35 mM borate-35 mM phosphate buffer solution (pH 8.6), containing 6% (v/v) of acetonitrile. Analyses were realised using fused-silica capillaries (57 cm length x 75 microm I.D.) and the operating conditions were: 15 kV applied voltage, 30 degrees C and detection at 279 nm. Piromidic acid was used as an internal standard. The linear concentration range of application was 1.0-120.0 microg ml(-1) for both compounds, with a detection limit of 0.2 microg ml(-1) for grepafloxacin and 0.3 microg ml(-1) for clinafloxacin. The analysis yielded good reproducibility (RSD between 3.37 and 1.74%). It was applied to the determination of grepafloxacin and clinafloxacin in human and rat urine samples. The method was validated using HPLC as a reference method. Recovery levels were between 94.5 and 103%.     

Determination of fosfomycin in biological fluids by capillary electrophoresis

A capillary electrophoresis method was developed for the determination of the antibiotic fosfomycin in serum, cerebrospinal fluid and aqueous humor. The technique uses indirect UV detection and the working buffer includes an organic cation to improve fosfomycin mobility. The electrophoretic time of migration is less than 7 min in both fluids. The limit of quantification is 2.5 and 1 μg/ml in serum and aqueous fluids, respectively (signal-to-noise RATIO = 3). The method was validated in serum and water over the concentration range 2.5–200 μg/ml. The calibration graph for serum was linear with a correlation coefficient r = 0.999. At a fosfomycin concentration of 2.5 μg/ml in serum, the intra- and inter-day precisions (coefficients of variation) were 5 and 5.2%, respectively. The mean recovery in serum was 94.5% (S.D. = 2.4%).     

Determination of piracetam in human plasma by capillary electrophoresis

A capillary electrophoresis (CE) procedure has been developed for the determination of piracetam in human plasma. Analyses were performed on an uncoated silica capillary using borax buffer modified with the addition of α-cyclodextrin. The detection was UV, operated at 200 nm. The detection limit of the authentic samples was 1 μg/ml. The calibration curve was linear over a range of 4 to 24 μg/ml (r=0.997). Inter-assay R.S.D. was below 9.3%. The described method has been successfully applied to the quantitative determination of piracetam in human plasma and should be useful for clinical and bioavailability investigations.     

Anaerobic degradation of benzene in BTX mixtures dependent on sulfate reduction

Abstract Enrichment cultures from marine sediments mineralized benzene while using sulfate as the terminal electron acceptor. Parallel cultures using river marsh sediment displayed no activity. Mineralization was confirmed by release of ¹⁴CO₂ from radiolabeled benzene. The dependence on sulfate reduction was demonstrated by stoichiometric balances and the use of specific inhibitors. This work supports recent observations that anaerobic benzene degradation takes place coupled to sulfate reduction.     

Determination of protein charge by capillary zone electrophoresis

The feasibility of employing classical electrophoresis theory to determine the net charge (valence) of proteins by capillary zone electrophoresis is illustrated in this paper. An outline of a procedure to facilitate the interpretation of mobility measurements is demonstrated by its application to a published mobility measurement for Staphylococcal nuclease at pH 8.9 that had been obtained by capillary zone electrophoresis. The significantly higher valence of +7.5 (cf. 5.6 from the same series of measurements) that has been reported on the basis of a "charge ladder" approach for charge determination signifies the likelihood that the latter generic approach may be prone to error arising from nonconformity of the experimental system with an inherent assumption that chemical modification or mutation of amino acid residues has no effect on the overall three-dimensional size and shape of the protein.     

Determination of the basicity of Mannich ketones by capillary electrophoresis

Capillary electrophoretic (CE) method to characterise Mannich ketones (MKs) containing morpholine moiety was developed. Basicity (pKa,exp) of the MKs was characterised by measured data derived from the electrophoretic mobility values obtained in the CE separation. The MKs were found to be weaker bases than the parent morpholine molecule itself and the experimentally determined basicity values proved to be dependent on the chemical structure of the MKs. Since the basicity of the MKs has an influence on their reactivity and biological activity it seems to be useful to determine experimentally the pKa,exp values of the newly synthesised compounds to support rational drug design or screening of the molecule libraries.     

Analysis of trifluoroacetic acid in lyophilized natural products by capillary electrophoresis

A rapid and simple method for the capillary electrophoretic determination of residual trifluoroacetic acid in lyophilized natural products is described. The technique utilizes 2,6-naphthalenedicarboxylic acid as a separation buffer additive providing indirect ultraviolet absorption detection. Using this method, acceptable precision, accuracy, selectivity, range and linearity were achieved.     

Anaerobic degradation of citrate under sulfate reducing and methanogenic conditions

Citrate is an important component of metal processing effluents such as chemical mechanical planarization wastewaters of the semiconductor industry. Citrate can serve as an electron donor for sulfate reduction applied to promote the removal of metals, and it can also potentially be used by methanogens that coexist in anaerobic biofilms. The objective of this study was to evaluate the degradation of citrate with sulfate-reducing and methanogenic biofilms. During batch bioassays, the citrate, acetate, methane and sulfide concentrations were monitored. The results indicate that independent of the biofilm or incubation conditions used, citrate was rapidly fermented with specific rates ranging from 566 to 720 mg chemical oxygen demand (COD) consumed per gram volatile suspended solids per day. Acetate was found to be the main fermentation product of citrate degradation, which was later degraded completely under either methanogenic or sulfate reducing conditions. However, if either sulfate reduction or methanogenesis was infeasible due to specific inhibitors (2-bromoethane sulfonate), absence of sulfate or lack of adequate microorganisms in the biofilm, acetate accumulated to levels accounting for 90–100% of the citrate-COD consumed. Based on carbon balances measured in phosphate buffered bioassays, acetate, CO₂ and hydrogen are the main products of citrate fermentation, with a molar ratio of 2:2:1 per mol of citrate, respectively. In bicarbonate buffered bioassays, acetogenesis of H₂ and CO₂ increased the yield of acetate. The results taken as a whole suggest that in anaerobic biofilm systems, citrate is metabolized via the formation of acetate as the main metabolic intermediate prior to methanogenesis or sulfate reduction. Sulfate reducing consortia must be enriched to utilize acetate as an electron donor in order to utilize the majority of the electron-equivalents in citrate.     

The separation of chondroitin sulfate disaccharides and hyaluronan oligosaccharides by capillary zone electrophoresis

We have developed techniques for the separation of unsulfated (2-acetamido-2-deoxy-3-O-(4-deoxy-alpha-L-threo- hex-4-enopyranosyluronicacid)-D-galactose and -D-glucose), monosulfated (2-acetamido-2-deoxy-3- O-(4-deoxy-2-O-sulfo-alpha-L-threo-hex-4-enopyranosyluronic acid)-D-galactose and 2-acetamido-2-deoxy-3-O-(4-deoxy-alpha-L-threo-hex- 4-enopyranosyluronic acid)-4-sulfo-D-galactose and -6-sulfo-D-galactose),disulfated (2-acetamido-2-deoxy-3-O-(4-deoxy-2-O-sulfo-alpha-L-threo-hex-4- enopyranosyluronic acid)-4-sulfo-D-galactose and -6-sulfo-D-galactose and 2-acet-amido-2-deoxy-3-O-(4-deoxy-alpha-L-threo-hex-4-enopy- ranosyluronic acid)-4,6-di-O-sulfo-D-galactose), and trisulfated (2-acetamido-2-deoxy-3-O-(4-deoxy-2-O- sulfo-alpha-L-threo-hex-4-enopyranosyluronic acid)-4,6-di-O-sulfo-D-galactose) isomers of chondroitin using capillary zone electrophoresis. In addition, it is possible to separate oligomers of hyaluronan by similar protocols. These techniques represent a rapid, sensitive, and reproducible technique for the assay of these molecules from digests of connective tissues.     

Determination of malondialdehyde in rat brain by capillary zone electrophoresis

A method for determination of malondialdehyde with capillary electrophoresis using UV detection at 267 nm has been developed. The buffer system consisted of 10 mM borax and 0.5 mM CTAB at pH 9.3. Malondialdehyde migrated as the first peak in the electropherogram at 2.6 min. Limit of detection was 1.2 μM corresponding to 7.8 pg. Malondialdehyde was determined before and after stimulating lipid peroxidation with the addition of ferrous ammonium sulphate to homogenates of rat brain tissue. Proteins were precipitated by boiling and removed from the brain homogenates with centrifugation. No further pretreatment was made before injecting the homogenates on the CE system. Non-precipitated homogenates could also be analyzed, but this required washing of the capillary with 0.1 M NaOH before introduction of the next sample.