Preparative-scale kinetic resolution of racemic styrene oxide by immobilized epoxide hydrolase

Epoxide hydrolase from Aspergillus niger was immobilized onto the modified Eupergit C 250 L through a Schiff base formation. Eupergit C 250 L was treated with ethylenediamine to introduce primary amine groups which were subsequently activated with glutaraldehyde. The amount of introduced primary amine groups was 220 μmol/g of the support after ethylenediamine treatment, and 90% of these groups were activated with glutaraldehyde. Maximum immobilization of 80% was obtained with modified Eupergit C 250 L under the optimized conditions. The optimum pH was 7.0 for the free epoxide hydrolase and 6.5 for the immobilized epoxide hydrolase. The optimum temperature for both free and immobilized epoxide hydrolase was 40 °C. The free epoxide hydrolase retained 52 and 33% of its maximum activity at 40 and 60 °C, respectively after 24 h preincubation time whereas the retained activities of immobilized epoxide hydrolase at the same conditions were 90 and 75%, respectively. Immobilized epoxide hydrolase showed about 2.5-fold higher enantioselectivity than that of free epoxide hydrolase. A preparative-scale (120 g/L) kinetic resolution of racemic styrene oxide using immobilized preparation was performed in a batch reactor and (S)-styrene oxide and (R)-1-phenyl-1,2-ethanediol were both obtained with about 50% yield and 99% enantiomeric excess. The immobilized epoxide hydrolase was retained 90% of its initial activity after 5 reuses.     

Immobilization and biocatalysis of chlorophyllase in selected organic solvent systems

Chlorophyllase extract from Phaeodactylum tricornutum was immobilized by physical adsorption on DEAE-cellulose and silica gel as well as by covalent binding on Eupergit C, Eupergit C250L, Eupergit C/ethylenediamine (EDA) and Eupergit C250L/EDA. Although the highest immobilization yield (83-93%) and efficiency (51-53%) were obtained when chlorophyllase extract was immobilized on DEAE-cellulose and silica gel, there was no improvement in the thermal stability of chlorophyllase as compared to that of the free one. The immobilization of chlorophyllase extract on Eupergit C250L/EDA resulted by a high recovery of enzymatic activity, with an immobilization efficiency of 44%, and promoted a higher stabilization of chlorophyllase (four times) in the aqueous/miscible organic solvent medium. On the other hand, the inhibitory effect of refined bleached deodorized (RBD) canola oil was reduced by immobilization of chlorophyllase extract onto silica gel as compared to those obtained with other enzyme preparations. However, the re-cycled chlorophyllase extract immobilized on Eupergit C250L/EDA retained more than 75% of its initial enzyme activity after 6 cycles, whereas that immobilized on silica gel was completely inactivated. The highest catalytic efficiency, for both free and immobilized chlorophyllase on Eupergit C250L/EDA, was obtained in the ternary micellar system as compared to the aqueous/miscible organic solvent and biphasic media.     

Immobilization of dextransucrase from Leuconostoc mesenteroides NRRL B-512F on Eupergit C supports

Dextransucrase from Leuconostoc mesenteroides B-512F was immobilized on epoxy-activated acrylic polymers with different textural properties (Eupergit C and Eupergit C 250L). Prior to immobilization, dextransucrase was treated with dextranase to remove the dextran layer covering the enzyme surface, thus increasing the accessibility of its reactive groups to the epoxide centers of the support. Elimination of 99% of the initial carbohydrate content was determined by the anthrone method. To prevent enzyme inactivation, the immobilization was carried out at pH 5.4, at which the coupling to the support took place through the carboxylic groups of the enzyme. The effects of the amount (mg) of dextransucrase added per gram of support (from 0.2:1 to 30:1), temperature and contact time were studied. Maximum activity recovery of 22% was achieved using Eupergit C 250L. Using this macroporous support, the maximum specific activity (710 U/g biocatalyst) was significantly higher than that obtained with the less porous Eupergit C (226 U/g biocatalyst). The dextransucrase immobilized on Eupergit C 250L showed similar optimal temperature (30 degrees C) and pH (5-6) compared with the native enzyme. In contrast, a notable stabilization effect at 30 degrees C was observed as a consequence of immobilization. After a fast partial inactivation, the dextransucrase immobilized on Eupergit C 250L maintained more than 40% of the initial activity over the following 2 days. The features of this immobilized system are very attractive for its application in batch and fixed-bed bioreactors.     

Immobilization of β-galactosidase on modified polypropilene membranes

A new immobilized system: β-galactosidase-modified polypropylene membrane was created. It was obtained 13 different carriers by chemical modification of polypropylene membranes by two stages. The first stage is treatment with K(2)Cr(2)O(7) to receive carboxylic groups on membrane surface. The second stage is treatment with different modified agents ethylendiamine, hexamethylenediamine, hydrazine dihydrochloride, hydroxylamine, o-phenylenediamine, p-phenylenediamine, N,N'-dibenzyl ethylenediamine diacetate to receive amino groups. The quantity of the amino groups, carboxylic groups and the degree of hydrophilicity of unmodified and modified polypropilene membranes were determined. β-Galactosidase was chemically immobilized on the obtained carries by glutaraldehyde. The highest relative activity of immobilized enzyme was recorded at membrane modified with 10% hexamethylenediamine (Membrane 5) - 92.77%. The properties of immobilized β-galactosidase on different modified membranes - pH optimum, temperature optimum, pH stability and thermal stability were investigated and compared with those of free enzyme. The storage stability of all immobilized systems was studied. It was found that the most stable system is immobilized enzyme on Membrane 5. The system has kept 90% of its initial activity at 300th day (pH=6.8; 4°C). The stability of the free and immobilized β-galactosidase on the modified membrane 5 with 10% HMDA in aqueous solutions of alcohols - mono-, diol and triol was studied. The kinetics of enzymatic reaction of free and immobilized β-galactosidase on the modified membrane 5 at 20°C and 40°C and at the optimal pH for both forms of the enzyme were investigated. It was concluded that the modified agent - hexamethylenediamine, with long aliphatic chain ensures the best immobilized β-galactosidase system.     

Efficient immobilization of epoxide hydrolase onto silica gel and use in the enantioselective hydrolysis of racemic para-nitrostyrene oxide

Epoxide hydrolase from Aspergillus niger (E.C. 3.3.2.3) was immobilized by covalent linking to epoxide-activated silica gel under mild conditions. A very easy procedure allowed to prepare an immobilized biocatalyst with more than 90% retention of the initial enzymatic activity. Immobilized and free enzyme showed very similar behaviour with respect to the effect of pH on activity and stability. One benefit of immobilizing epoxide hydrolase from A. niger on silica gel was the enhanced enzyme stability in the presence of 20% DMSO. The kinetic resolution of racemic para-nitrostyrene oxide was investigated by using this new immobilized biocatalyst. The enantioselectivity of the enzyme was not altered by the immobilization reaction: both unreacted epoxide and formed diol were obtained with very high ee (99 and 92%, respectively). In addition, the biocatalyst could be easily separated from the reaction mixture and re-used for over nine cycles without any noticeable loss of enzymatic activity or change in the enantioselectivity extent. The activity of immobilized AnEH was retained for several months.     

Production of xylobiose from the autohydrolysis explosion liquor of corncob using Thermotoga maritima xylanase B (XynB) immobilized on nickel-chelated Eupergit C

In this study, a thermostable recombinant xylanase B (XynB) from Thermotoga maritima MSB8 was immobilized on nickel-chelated Eupergit C 250L. This immobilized XynB was then used to hydrolyze the autohydrolysis explosion liquor of corncob (AELC) in a packed-bed enzyme reactor for continuous production of xylooligosaccharides, especially xylobiose. When tested in batch hydrolysis of AELC, the immobilized XynB still retained its relative activity of 92.5% after 10 cycles of hydrolysis at 90 degrees C. The immobilized XynB retained 83.6% of its initial hydrolysis activity even after 168 h of hydrolysis reaction at 90 degrees C and demonstrated a half-life time of 577.6 h (24 days) for continuous hydrolysis. HPLC showed that xylobiose (49.8%) and xylose (22.6%) were the main hydrolysis products yielded during continuous hydrolysis. Xylobiose was adsorbed on an activated charcoal column and eluted with a linear gradient of 15% (v/v) ethanol to yield xylobiose with 84.7% of recovery. Also, the purity of xylobiose was up to 97.2% as determined by HPLC. Therefore, the immobilized XynB was suitable for the efficient production of xylobiose from AELC. This is the first report on the immobilization of xylanase for xylobiose production.     

Methods for the immobilization of lipases and their use for ester synthesis

The lipase from Pseudomonas fluorescens was immobilized onto five different carriers: celite, octyl-silica, aminopropyl-silica, gluterdialdehyde-activated silica and Eupergit C250L. Activities and operational stabilities of the prepared catalysts were compared using the enantioselective acylation of (R,S)-1-phenylethanol by vinyl acetate as acyl donor and t-butylmethyl ether with variable water content (0.038-0.97% v/v) as reaction medium. The above carriers provide catalysts with widely different specific activities ranging from excellent 25 mmol/h mg protein (celite) to 0.07 mmol/h mg protein (glutardialdehyde-activated silica) on the lower end. The lipase immobilized onto Eupergit C250L exhibited the best operational stability among the catalysts studied. It retained 30% of its initial activity after 11 cycles of application, each with a duration between 2 and 6 h.     

The influence of bond chemistry on immobilized enzyme systems for ex vivo use

The ideal derivatized support for the clinical use of an immobilized enzyme system should irreversibly bind active enzyme. We have investigated the behavior of heparinase and bilirubin oxidase immobilized via cyanogen bromide, tresyl chloride, epoxide, or carbodiimidazole activated natural and synthetic matrices. The protein bound to each activated support was 90% for cyanogen bromide (CNBr) activated agarose, 50-80% for tresyl chloride activated agarose, and 50% for oxirane activated acrylic (Eupergit C). The activity retention of immobilized heparinase was greatest (50%) with CNBr activated agarose while for the immobilization of bilirubin oxidase, the activity retention was greatest (25-30%) with tresyl chloride activated agarose and oxirane activated acrylic.The stability of the different covalent bonds was studied in vitro with radioiodinated enzymes. The leaching profiles showed the same trends for each support and chemistry. A plateau in portein leaching was reached after a few hours of incubatttion and the transient leaching period was well represented byu a logarithimic function of time. The amount of enzyme released from the least stable support (CNBr activated agarose) in 24 h was injected intravenously in New Zealand white rabbits. Using an indirect enzyme-linked immunnosorbant assay (ELISA), no immune responce was detected. The transient leaching profile was shortenend by washingthe enzyme-support conjugate with 1M hydroxylamine, pH8.5 intermolecular cross-linking with glutaraldehyde also improves the enzyme-support stability. Tresyl chloride and oxirane activated supports produce bonds with improved stability without adversely affecting enzymatic activity.     

Modification and characterization of cellulosic cotton fibers for efficient immobilization of urease

Cotton fibers were first grafted by polyacrylonitril in the presence of KMnO(4) and oxalic acid as a combined redox initiator. Moreover, modification of the grafted cotton fibers was done by changing the nitrile group (-CN) into hydrazidine group through the reaction with hydrazine hydrate, then the fibers were activated by glutaraldehyde to introduce free aldehyde groups which were able to react with amino groups of urease to form Schiff's base, and result in cotton fibers immobilized urease. The efficiency of the immobilization was evaluated by examining the relative enzymatic activity of enzyme before and after the immobilization of urease. The results showed that the optimum temperature of immobilized urease was 35°C, which was higher than that of the free enzyme (30°C), and the immobilized urease exhibited a higher relative activity than that of free urease over 35°C. The optimal pH for immobilized urease was 6.5, which was lower than that of the free urease (pH 7.0), and the immobilization resulted in stabilization of enzyme over a wider pH range. The kinetic constant value (K(m)) of immobilized urease was higher than that of the free urease. However, the thermal and operational stabilities of immobilized urease have been improved greatly.     

Immobilization of oxalate decarboxylase to Eupergit and properties of the immobilized enzyme

Oxalate decarboxylase, an oxalate degradation enzyme used for medical diagnosis and decreasing the oxalate level in the food or paper industry, was covalently immobilized to Eupergit C. Different immobilization parameters, including ratio of enzyme to support, ammonia sulfate concentration, pH, and incubation time, were optimized. Under the condition of enzyme/support ratio at 1:20, pH 9, with 1.5?mol/L (NH(4))(2)SO(4), room temperature, and shaking at 30?rpm for 24?hr, activity recovery of immobilized Oxdc reached 90% with an apparent specific activity of 0.44?U/mg support. The enzymatic properties of immobilized Oxdc were investigated and compared with those of the soluble enzyme. Both shared a similar profile of optimum conditions; the optimum pH and temperature for soluble and immobilized Oxdc were 3.5 and 50°C, respectively. The immobilized enzyme was more stable at lower pH and higher temperatures. The kinetic parameters for soluble and immobilized enzyme were also determined.     

Immobilization and stabilization of α-galactosidase on Sepabeads EC-EA and EC-HA

α-Galactosidase from tomato has been immobilized on Sepabead EC-EA and Sepabead EC-HA, which were activated with ethylendiamino and hexamethylenediamino groups, respectively. Two strategy was used for the covalent immobilization of α-galactosidase on the aminated Sepabeads: covalent immobilization of enzyme on glutaraldehyde activated support and cross-linking of the adsorbed enzymes on to the support with glutaraldehyde. By using these two methods, all the immobilized enzymes retained very high activity and the stability of the enzyme was also improved. The obtained results showed that, the most stable immobilized α-galactosidase was obtained with the second strategy. The immobilized enzymes were characterized with respect to free counterpart. Some parameters effecting to the enzyme activity and stability were also analyzed. The optimum temperature and pH were found as 60 °C and pH 5.5 for all immobilized enzymes, respectively. All the immobilized α-galactosidases were more thermostable than the free enzyme at 50 °C. The stabilities of the Sepabead EC-EA and EC-HA adsorbed enzymes treated with glutaraldehyde compared to the stability of the free enzyme were a factor of 6 for Sepabead EC-EA and 5.3 for Sepabead EC-HA. Both the free and immobilized enzymes were very stable between pH 3.0 and 6.0 and more than 85% of the initial activities were recovered. Under the identical storage conditions the free enzyme lost its initial activity more quickly than the immobilized enzymes at the same period of time. The immobilized α-galactosidase seems to fulfill the requirements for different industrial applications.     

Immobilization of Bacillus licheniformis L-Arabinose Isomerase for Semi-Continuous L-Ribulose Production

Bacillus licheniformis L-arabinose isomerase (BLAI) with a broad pH range, high substrate specificity, and high catalytic efficiency for L-arabinose was immobilized on various supports. Eupergit C, activated-carboxymethylcellulose, CNBr-activated agarose, chitosan, and alginate were tested as supports, and Eupergit C was selected as the most effective. After determination of the optimum enzyme concentration, the effects of pH and temperature were investigated using a response surface methodology. The immobilized BLAI enzyme retained 86.4% of the activity of the free enzyme. The optimal pH for the immobilized BLAI was 8.0, and immobilization improved the optimal temperature from 50 °C (free enzyme) to a range between 55 and 65 °C. The half life improved from 2 at 50 °C to 212 h at 55 °C following immobilization. The immobilized BLAI was used for semi-continuous production of L-ribulose. After 8 batch cycles, 95.1% of the BLAI activity was retained. This simple immobilization procedure and the high stability of the final immobilized BLAI on Eupergit C provide a promising solution for large-scale production of L-ribulose from an inexpensive L-arabinose precursor.     

Comparative study of thermostabilty and ester synthesis ability of free and immobilized lipases on cross linked silica gel

A novel support has been utilized for immobilization of lipase, which was prepared by amination of silica with ethanolamine followed by cross linking with glutaraldehyde. Lipases from Rhizopus oryzae 3562 and Enterobacter aerogenes were immobilized on activated silica gel, where they retained 60 and 50% of respective original activity. The thermal stability of the immobilized lipases was significantly improved in comparison to the free forms while the pH stability remained unchanged. E. aerogenes and R. oryzae 3562 lipases retained 75 and 97% of respective initial activity on incubation at 90 degrees C, whereas both the free forms became inactive at this temperature. The conversion yield of isoamyl acetate was found to be higher with the immobilized fungal (90 vs. 21%) and bacterial lipases (64 vs. 18%) than the respective free forms. Immobilized R. oryzae 3562 lipases retained 50% activity for isoamyl acetate synthesis up to ten cycles whereas it was eight cycles for E. aerogenes.     

Immobilization of pycnoporus coccineus laccase on Eupergit C: Stabilization and treatment of olive oil mill wastewaters

The use of olive oil mill wastewaters (OMW) as an organic fertilizer is limited by their phytotoxic effect, due to the high concentration of phenolic compounds. As an alternative to physico-chemical methods for OMW detoxification, the laccase from Pycnoporus coccineus, a white-rot fungus with the ability to decrease the chemical oxygen demand (COD) and color of the industrial effluent, is being studied. In this work, the P. coccineus laccase was immobilized on two acrylic epoxy-activated resins, Eupergit C and Eupergit C 250L. The highest activity was obtained with the macroporous Eupergit C 250L, reaching 110 U g^?1 biocatalyst. A substantial stabilization effect against pH and temperature was obtained upon immobilization. The soluble enzyme maintained ≥80% of its initial activity after 24 h at pH 7.0–10.0, whereas the immobilized laccase kept the activity in the pH range 3.0–10.0. The free enzyme was quickly inactivated at temperatures >50°C, whereas the immobilized enzyme was very stable up to 70°C. Gel filtration profiles of the OMW treated with the immobilized enzyme (for 8 h at room temperature) showed both degradation and polymerization of the phenolic compounds.     

Immobilization of urease on vermiculite

Urease (EC 3.5.1.5) of high activity was obtained when the enzyme was immobilized on vermiculite crosslinked with 2.5% glutaraldehyde in chilled EDTA-phosphate buffer (pH 5.5). The highest activity of the immobilized enzyme was at 65°C and pH 6.5 while the optimum temperature for free urease was found to be 25°C. The thermal stability of immobilized urease was observed to be much better than that of the free urease. When stored at 4°C, urease immobilized on vermiculite retained 69 to 81% of its activity after 60 days and 61 to 75% of its original activity was retained after 4 repeated uses.     

Optimization of covalent immobilization of pectinase on sodium alginate support

Pectinase was immobilized on a sodium alginate support using glutaraldehyde and retained 66% activity. The optimal pH for activity shifted from 3.0 to 3.5 after immobilization; however, the optimum temperature remained unchanged at 40°C. The immobilized enzyme also had a higher thermal stability and reusability than the free enzyme, and retained 80% of initial activity after 11 batch reactions.     

Immobilization of soybean seed coat peroxidase on polyaniline: Synthesis optimization and catalytic properties

Soybean seed coat peroxidase (SBP) was immobilized on various polyaniline-based polymers (PANI), activated with glutaraldehyde. The most reduced polymer (PANIG₂) showed the highest immobilization capacity (8.2 mg SBP g^-1 PANIG₂). The optimum pH for immobilization was 6.0 and the maximum retention was achieved after a 6-h reaction period. The efficiency of enzyme activity retention was 82%. When stored at 4°C, the immobilized enzyme retained 80% of its activity for 15 weeks as evidenced by tests performed at 2-week intervals. The immobilized SBP showed the same pH-activity profile as that of the free SBP for pyrogallol oxidation but the optimum temperature (55°C) was 10°C below that of the free enzyme. Kinetic analysis show that the K_m was conserved while the specific V_max dropped from 14.6 to 11.4 µmol min^-1 µg^-1, in agreement with the immobilization efficiency. Substrate specificity was practically the same for both enzymes. Immobilized SBP showed a greatly improved tolerance to different organic solvents; while free SBP lost around 90% of its activity at a 50% organic solvent concentration, immobilized SBP underwent only 30% inactivation at a concentration of 70% acetonitrile. Taking into account that immobilized HRP loses more than 40% of its activity at a 20% organic solvent concentration, immobilized SBP performed much better than its widely used counterpart HRP.     

The potential of immobilized bacterial α-amylase on coconut coir,a smart carrier for biocatalysts

Purified α-amylase from a soil bacterium Bacillus sp. SKB4 was immobilized on coconut coir, an inexpensive cellulosic fiber, with the cross-linking agent glutaraldehyde. The catalytic properties and stability of the immobilized enzyme were compared with those of its soluble form. The enzyme retained 97.2% of its activity and its catalytic properties were not drastically altered after immobilization. The pH optimum and stability of the immobilized enzyme were shifted towards the alkaline range compared to the free enzyme. The optimum temperature for enzymatic activity was 90°C in both forms of the enzyme. The soluble and immobilized enzyme retained 19% and 70% of original activity, respectively, after pre-incubation for 1 h at 90°C. Immobilized amylase was less susceptible to attack by heavy metal ions and showed higher K_m and V_max values than its free form. The bound enzyme showed significant activity and stability after 6 months of storage at 4°C. All of these characteristics make the new carrier system suitable for use in the bioprocess and food industries.     

Preparation of immobilized/stabilized biocatalysts of β-glucosidases from different sources: Importance of the support active groups and the immobilization protocol

β-Glucosidases from two different commercial preparations, Pectinex Ultra SP-L and Celluclast® 1.5L, were immobilized on divinylsulfone (DVS) supports at pH 5.0, 7.0, 9.0, and 10. In addition, the biocatalysts were also immobilized in agarose beads activated by glyoxyl, and epoxide as reagent groups. The best immobilization results were observed using higher pH values on DVS-agarose, and for Celluclast® 1.5L, good results were also obtained using the glyoxil-agarose immobilization. The biocatalyst obtained using Pectinex Ultra SP-L showed the highest thermal stability, at 65°C, and an operational stability of 67% of activity after 10 reuses cycles when immobilized on DVS-agarose immobilized at pH 10 and blocked with ethylenediamine. The β-glucosidase from Celluclast® 1.5L produced best results when immobilized on DVS-agarose immobilized at pH 9 and blocked with glycine, reaching 7.76-fold higher thermal stability compared to its free form and maintaining 76% of its activity after 10 successive cycles. The new biocatalysts obtained by these protocols showed reduction of glucose inhibition of enzymes, demonstrating the influence of immobilization protocols, pH, and blocking agent.     

Immobilization of the epoxide hydrolase from Aspergillus niger

Three methods for the immobilization of the epoxide hydrolase from the fungus Aspergillus niger were tested. The highest immobilization yield (90%) and retention of activity (65%) were obtained by adsorption onto DEAE-cellulose compared to adsorption onto hydrophobic porous polypropylene and covalent linkage using Eupergit resin. The enzymatic properties of the immobilized enzyme were similar to those of the free enzyme with respect to the effect of temperature and pH on both activity and stability as well as the effect of solvent (DMF) on activity. The kinetic parameters were affected leading to lower K _M(app) and higher Vm _(app).