Intrinsically antibacterial materials based on polymeric derivatives of eugenol for biomedical applications

Infections are the most common cause of biomaterial implant failure representing a constant challenge to the more widespread application of medical implants. This study reports on the preparation and characterization of novel hydrophilic copolymeric systems provided with antibacterial properties coming from eugenol residues anchored to the macromolecular chains. Thus, high conversion copolymers were prepared from the hydrophilic monomer 2-hydroxyethyl methacrylate (HEMA) and different eugenol monomeric derivatives, eugenyl methacrylate (EgMA) and ethoxyeugenyl methacrylate (EEgMA), by bulk polymerization reaction. Thermal evaluation revealed glass transition temperature values in the range 95-58 degrees C following the order HEMA-co-EgMA > PHEMA > HEMA-co-EEgMA and a clear increase in thermal stability with the presence of any eugenyl monomer in the system. In vitro wettability studies showed a reduction of water sorption capacity and surface free energy values with increasing the content of eugenol residues in the copolymer. The antimicrobial activity of copolymeric discs was evaluated by determining their capacity to reduce or inhibit colony formation by different bacterial species. All eugenyl containing materials showed bacteria growth inhibition, this one being higher for the EEgMA derivative copolymers.     

Metalloinitiation routes to biocompatible poly(lactic acid) and poly(acrylic acid) stars with luminescent ruthenium tris(bipyridine) cores

Poly(lactic acid) (PLA) and poly(acrylic acid) (PAA) biomaterials with luminescent ruthenium tris(bipyridine) centers couple drug delivery and imaging functions. Hydrophobic [Ru(bpyPLA2)3](PF6)2 (1) was generated from [Ru[bpy(CH2OH)2]3](PF6)2 in bulk monomer using 4-(dimethylamino)pyridine as the catalyst. The bromoesters, [Ru[bpy(CH2OR)2]3](PF6)2, [Ru[bpy(C13H27)2][bpy(CH2OR]2](PF6)2 (4), and [Ru[bpy(PLAOR)2]3]2+ (9) (R=COCBr(CH3)2), served as initiators for tert-butyl acrylate (tBA) polymerization. Conversion of PtBA to PAA via hydrolysis affords water soluble materials, [Ru(bpyPAA2)3]2+ (7) and [Ru[bpy(C13H27)2](bpyPAA2)2]2+ (8) and the amphiphilic star polymer [Ru[bpy(PLA-PAA)2]3)](PF6)2 (11), which is soluble in a H2O/CH3CN (1:1) mixture. Luminescence excitation and emission spectra of the Ru polymers were in agreement with the parent [Ru(bpy)3]2+ chromophore (lambdaex=468, lambdaem=621 nm). Lifetimes of tau approximately 700 ns in both air and nitrogen atmospheres are typical for most materials; however, the amphiphilic star block copolymer 11 is quenched by oxygen to some degree. Thermal analysis shows the expected glass transitions for the polymeric ruthenium complex materials.     

Rapid deswelling response of poly(N-isopropylacrylamide)/poly(2-alkyl-2-oxazoline)/poly(2-hydroxyethyl methacrylate) hydrogels

Ternary poly( N-isopropylacrylamide)/poly(2-alkyl-2-oxazoline)/poly(2-hydroxyethyl methacrylate) (PNIPAAm/PROZO/PHEMA) hydrogels were prepared by the free-radical copolymerization of N-isopropylacrylamide (NIPAAm), 2-hydroxyethyl methacrylate (HEMA), and poly(2-alkyl-2-oxazoline) (PROZO) multifunctional macromonomers. The resulting polymeric materials were characterized by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and scanning electron microscopy (SEM), as well as by equilibrium swelling experiments. All synthesized hydrogels display temperature sensitivity in the 28-38 degrees C range. A high rate of response was registered as compared to that of materials based only on PNIPAAm. The swelling-deswelling peculiar behavior was related to the chemical composition (hydrophile/hydrophobe balance), the length of the inserted PROZO sequence, and inner morphology, an aspect which points on its possible control by synthesis. It was evidenced that the architecture of the resulting porous materials has a high order degree, emerging from the self-assembling of the microgel particles, which provided numerous, nearly uniform, large water release channels.     

Cu(0) as the reaction additive in purge-free ATRP-assisted DNA detection

We report here the use of Cu(0) as a reducing reagent to eliminate dissolved oxygen-induced ATRP catalyst oxidation and radical chain termination. It eliminates the need for an inert environment as in a conventional ATRP reaction and allows DNA detection to be conducted in a purge-free fashion. 2-Hydroxyethylmethacrylate (HEMA) is the model monomer in our study, and Cu(I)/2,2'-dipyridyl-based complexes are used as the reaction catalyst. The amount of polymer chains grafted on the substrate upon reaction termination is quantified by measuring the final film thicknesses using ellipsometry. Synthesis of PHEMA films atop both small molecules and ssDNA in the presence of a limited amount of air at room temperature is achieved by adding Cu(0) as the reducing reagent. No compromised DNA detection sensitivity is noticed, though a 10:1 ratio of Cu(0):Cu(I) is required to achieve optimal polymer growth. Successful employment of Cu(0) as the reducing agent eliminates the cumbersome purging process in ATRP and renders the ATRP-assisted DNA sensing method more portable, simpler, and more time-efficient.     

ATRP synthesis of amphiphilic random,gradient, and block copolymers of 2-(dimethylamino)ethyl methacrylate and n-butyl methacrylate in aqueous media

Amphiphilic random, gradient, and block copolymers of 2-(dimethylamino)ethyl methacrylate (DMAEMA) and n-butyl methacrylate (BMA) were synthesized by atom transfer radical polymerization (ATRP) in water/2-propanol mixtures using a methoxy-poly(ethylene glycol) (MPEG) (M(n) = 2000) macroinitiator. Kinetic studies indicate that the copolymerization is well controlled with molecular weights increasing linearly with conversion. Copolymers with molecular weights up to M(n) = 34000 and low polydispersities (M(w)/M(n) = 1.11-1.47) were prepared. The reactivity ratios were calculated for the copolymerizations catalyzed by CuBr/bpy, (r(DMAEMA) = 1.07, r(BMA) = 1.24). The thermosensitivity and aggregation properties of the random, gradient, and block copolymers significantly depended on the architecture of the copolymers. The lower critical solution temperature of MPEG-b-PDMAEMA(84) was 38 degrees C (5 wt % in water).     

Water-soluble degradable hyperbranched polyesters: novel candidates for drug delivery?

A novel approach to hyperbranched polymers is presented in this work. Hyperbranched polyesters with a large amount of terminal hydroxyl groups are prepared by a one-pot synthesis from commercially available AB-type and CD(n)-type monomers (n >/= 2). In this paper, Michael addition of diethanolamine (CD(2)) or N-methyl-d-glucamine (CD(5)) to methyl acrylate (AB) generates dominantly AD(n)-type intermediates. Further self-condensation of intermediates at higher temperature and in the presence of catalyst gives hyperbranched polyesters. Because of the tertiary amino groups in the backbone and the hydroxyl groups in the linear and terminal units, the resulting hyperbranched polyester is highly soluble in water. Furthermore, the hyperbranched polymer is degradable because of its ester units. So, the water-soluble hyperbranched polyesters might be applied as a novel material for drug delivery.     

Redox-responsive polyphosphate nanosized assemblies: a smart drug delivery platform for cancer therapy

Novel redox-responsive polyphosphate nanosized assemblies based on amphiphilic hyperbranched multiarm copolyphosphates (HPHSEP-star-PEP(x)) with backbone redox-responsive, good biocompatibility, and biodegradability simultaneously have been designed and prepared successfully. The hydrophobic core and hydrophilic multiarm of HPHSEP-star-PEP(x) are composed of hyperbranched and linear polyphosphates, respectively. Benefiting from the amphiphilicity, HPHSEP-star-PEP(x) can self-assemble into spherical micellar nanoparticles in aqueous media with tunable size from about 70 to 100 nm via adjusting the molecular weight of PEP multiarm. Moreover, HPHSEP-star-PEP(x) micellar structure can be destructed under reductive environment and result in a triggered drug release behavior. The glutathione-mediated intracellular drug delivery was investigated against a HeLa human cervical carcinoma cell line, and the results indicate that doxorubicin-loaded (DOX-loaded) HPHSEP-star-PEP(x) micelles show higher cellular proliferation inhibition against glutathione monoester pretreated HeLa cells than that of the nonpretreated ones. In contrast, the DOX-loaded micelles exhibit lower inhibition against buthionine sulfoximine pretreated HeLa cells. These results suggest that such redox-responsive polyphosphate micelles can rapidly deliver anticancer drugs into the nuclei of tumor cells enhancing the inhibition of cell proliferation and provide a favorable platform to construct excellent drug delivery systems for cancer therapy.     

Amphiphilic core-shell nanocarriers based on hyperbranched poly(ester amide)-star-PCL: synthesis, characterization, and potential as efficient phase transfer agent

Amphiphilic biodegradable star-shaped polymer was conveniently prepared by the Sn(Oct)2-catalyzed ring opening polymerization of epsilon-caprolactone (CL) with hyperbranched poly(ester amide) (PEA) as a macroinitiator. Various monomer/initiator ratios were employed to vary the length of the PCL arms. (1)H NMR and FTIR characterizations showed the successful synthesis of star polymer with high initiation efficiency. SEC analysis using triple detectors, RI, light scattering, and viscosity confirmed the controlled manner of polymerization and the star architecture. Because of the hydrophilic PEA core and hydrophobic PCL shell, the obtained star polymers displayed inverted unimolecular micellar structure confirmed by dynamic light scattering. Three water soluble dyes, congo red, methyl orange, and bromophenol blue, were used to investigate the host-guest behavior of the micelles. It proved that the core-shell unimolecular reverse micelles were able to transport polar dyes from water to the organic phase with a high efficiency of up to 22.6 dyes per polymer, indicating a great potential of the micelles as drug carriers. The influence of arm length and core size on the load efficiency of the nanocarrier was also evaluated.     

Antibody purification with protein A attached supermacroporous poly(hydroxyethyl methacrylate) cryogel

Immunoglobulin G (IgG) purification from human plasma with protein A attached supermacroporous poly(hydroxyethyl methacrylate) [PHEMA] cryogel has been studied. PHEMA cryogel was prepared by bulk polymerization which proceeds in aqueous solution of monomer frozen inside a plastic syringe (cryo-polymerization). After thawing, the PHEMA cryogel contains a continuous matrix having interconnected pores of 10–200 μm size. Protein was covalently attached onto the PHEMA cryogel via cyanogen bromide (CNBr) activation. The maximum IgG adsorption on the PHEMA/protein A cryogel was found to be 83.2 mg/g at pH 7.4 from aqueous solutions. The non-specific IgG adsorption onto the PHEMA cryogel was about 0.38 mg/g. The macropore size of the cryogel makes it possible to process blood cells without blocking the column. Higher adsorption capacity was observed from human plasma (up to 88.1 mg/g). Adsorbed IgG was eluted using 0.1 M glycine–HCl buffer (pH 3.5) with a purity of 85%. PHEMA–protein A cryogel was used for repetitive adsorption/desorption of IgG without noticeable loss in IgG adsorption capacity after 10 cycles. PHEMA–protein A cryogel showed several advantages such as simpler preparation procedure, good selectivity for IgG purification from human plasma and good stability throughout repeated adsorption–desorption cycles.     

(1)H NMR study of the states of water in equilibrium poly(HEMA-co-THFMA) hydrogels

The spin-spin relaxation times, T(2), of hydrated samples of poly(hydroxymethyl methacrylate), PHEMA, poly(tetrahydrofurfuryl methacrylate), PTHFMA, and the corresponding HEMA-THFMA copolymers have been examined to probe the states of the imbibed water in these polymers. The decay in the transverse magnetization of water in fully hydrated samples of PHEMA, PTHFMA, and copolymers of HEMA and THFMA was described by a multiexponential function. The short component of T(2) was interpreted as water molecules that were strongly interacting with the polymer chains. The intermediate component of T(2) was assigned to water residing in the porous structure of the samples. The long component of T(2) was believed to arise from water residing in the remnants of cracks formed in the polymer network during water sorption.     

Polypyrrole-hydrogel composites for the construction of clinically important biosensors.

The present study reports on the use of p(2-hydroxyethyl methacrylate) (pHEMA) in which polypyrrole and various oxidoreductase enzymes were physically entrapped to function as a viable matrix for the construction of clinically important amperometric biosensors. Glucose oxidase, cholesterol oxidase and galactose oxidase biosensors were constructed. Electrode-supported hydrogel films were prepared by UV polymerization of the HEMA component (containing the dissolved enzyme) followed immediately by electrochemical polymerization (+0.7V vs. Ag/AgCl) of the pyrrole component within the interstitial spaces of the pre-formed hydrogel network. The optimized glucose oxidase biosensor displayed a wide linear glucose response range (5.0 x 10(-5) to 2.0 x 10(-2) M), a detection limit (3S(y/x)/sensitivity) of 25 microM and a response time of 35-40 s. The analytical recovery of glucose in serum samples ranged from 98 to 102% with mean coefficients of variation of 4.4% (within-day analyses) and 5.1% (day-to-day analyses). All three sensors displayed good stabilities when stored desiccated in the absence of buffer (>9 months).     

Interpretation of concentration-dependence in aggregation kinetics

Aggregation processes are analyzed by two kinetic models, the random polymerization model and the nucleation-dependent polymerization model. A kinetic equation for the random polymerization model can be derived analytically, revealing the relation between the initial monomer concentration ([M]0), the rate constant (k(a)), time (t), the yield of detectable aggregate ([F]), and the critical aggregation number (m). However, time-course curves for the nucleation-dependent polymerization model can be obtained by numerical calculation. It is found that lag time (t(d)) and half-time (t1/2) are proportional to [M](-1) in the random polymerization model, while t(d) and t1/2 are proportional to [M1](-s) (1 < s < n; n is nucleus size) at the lower concentration and are less dependent on [M1] at the higher concentration in the nucleation-dependent polymerization model.     

Amphiphilic hyperbranched fluoropolymers as nanoscopic 19F magnetic resonance imaging agent assemblies

Three hyperbranched fluoropolymers were synthesized and their micelles were constructed as potential (19)F MRI agents. A hyperbranched star-like core was first synthesized via atom transfer radical self-condensing vinyl (co)polymerization (ATR-SCVCP) of 4-chloromethyl styrene (CMS), lauryl acrylate (LA), and 1,1,1-tris(4'-(2'-bromoisobutyryloxy)phenyl)ethane (TBBPE). The polymerization gave a small core with M n of 5.5 kDa with PDI of 1.6, which served as a macroinitiator. Trifluoroethyl methacrylate (TFEMA) and tert-butyl acrylate (tBA) in different ratios were then "grafted" from the core to give three polymers with M(n) of about 120 kDa and PDI values of about 1.6-1.8. After acidolysis of the tert-butyl ester groups, amphiphilic, hyperbranched star-like polymers with M(n) of about 100 kDa were obtained. These structures were subjected to micelle formation in aqueous solution to give micelles having TEM-measured diameters ranging from 3-8 nm and DLS-measured hydrodynamic diameters from 20-30 nm. These micelles gave a narrow, single resonance by (19)F NMR spectroscopy, with a half-width of approximately 130 Hz. The T1/T2 parameters were about 500 and 50 ms, respectively, and were not significantly affected by the composition and sizes of the micelles. (19)F MRI phantom images of these fluorinated micelles were acquired, which demonstrated that these fluorinated micelles maybe useful as novel (19)F MRI agents for a variety of biomedical studies.     

Polymers from fatty acids: poly(ω-hydroxyl tetradecanoic acid) synthesis and physico-mechanical studies

This Article describes the synthesis and physicomechanical properties of bioplastics prepared from methyl ω-hydroxytetradecanoic acid (Me-ω-OHC14), a new monomer available by a fermentation process using an engineered Candida tropicalis strain. Melt-condensation experiments were conducted using titanium tetraisopropoxide (Ti[OiPr](4)) as a catalyst in a two-stage polymerization (2 h at 200 °C under N(2), 4 h at 220 °C under 0.1 mmHg). Poly(ω-hydroxytetradecanoate), P(ω-OHC14), M(w), determined by SEC-MALLS, increased from 53K to 110K as the Ti(OiPr)(4) concentration increased from 50 to 300 ppm. By varying the polymerization conditions (catalyst concentration, reaction time, second-stage reaction temperature) a series of P(ω-OHC14) samples were prepared with M(w) values from 53K to 140K. The synthesized polyesters with M(w) ranging from 53K to 140K were subjected to characterization by DSC, TGA, DMTA, and tensile testing. Influences of P(ω-OHC14) molecular weight, melting point, and enthalpies of melting/crystallization on material tensile properties were explored. Cold-drawing tensile tests at room temperature for P(ω-OHC14) with M(w) 53K-78K showed a brittle-to-ductile transition. In contrast, P(ω-OHC14) with M(w) 53K undergoes brittle fracture. Increasing P(ω-OHC14) M(w) above 78K resulted in a strain-hardening phenomena and tough properties with elongation at break ~700% and true tensile strength of ~50 MPa. Comparisons between high density polyethylene and P(ω-OHC14) mechanical and thermal properties as a function of their respective molecular weights are discussed.     

Factors affecting the production of prednisolone by immobilization of Bacillus pumilus E601 cells in poly(vinyl alcohol) cryogels produced by radiation polymerization

To increase the yield percent of prednisolone from hydrocortisone (cortisol), Bacillus pumilus E601 (a radioresistant microorganism) was incorporated into poly(vinyl alcohol) (PVA) cryogel grafted with hydroxyethyl-methacrylate (HEMA) as a crosslinking agent. The polymer was prepared by a radiation polymerization technique at 20 kGy from Co-60 source. The optimum temperature for the biotransformation of hydrocortisone by free cells, poly(PVA)/HEMA, and poly(PVA)/HEMA /N-isopropylacrylamide (N-IPAAm) was 30 °C. The highest yield % of prednisolone was obtained by immobilization of the cells on poly(PVA/HEMA), the addition of N-IPAAm to poly(PVA/HEMA) protected the immobilized cells from temperatures above 35 °C during the fermentation process. The optimal pH (buffered pH) of the biotransformation of hydrocortisone by immobilized and free cells was 7.0, but the maximum yield of prednisolone (60%) was obtained by immobilized cells in comparison with free cells (42%) also at pH 7.0. The prednisolone yield reached 60–65% with 1,2-propanediol cosolvent containing media and 60–62% in the case of ethanediol cosolvent containing media at 1% (v/v) of both cosolvents. 10 mg/50 ml Tween 80 the medium increased the prednisolone yield by only 1.1-fold compared with the control. The maximum bioconversion efficiency was obtained at a substrate concentration of 20 mg/50 ml medium. Stability studies showed that the immobilized cells can be used for seven times without any significant decrease in activity.     

Copper(II)-fluoroquinolone complexes with anti-Trypanosoma cruzi activity and DNA binding ability

Copper(II) complexes of fluoroquinolone antibacterial agents levofloxacin (LEV) and sparfloxacin (SPAR), containing or not a nitrogen donor heterocyclic ligand, 2,2'-bipyridine (bipy) or 1,10-phenathroline (phen), were prepared and characterized. The complexes are of the type [CuCl(2)(H(2)O)(L)], [CuCl(bipy)(L)]Cl and [CuCl(2)(phen)(L)], where L?=?LEV or SPAR. The data suggest that LEV and SPAR act as zwitterionic bidentade ligands coordinated to Cu(II) through the carboxylate and ketone oxygen atoms. The electron paramagnetic resonance spectra of the [CuCl(bipy)(L)]Cl and [CuCl(2)(phen)(L)] complexes (L?=?LEV and SPAR) in aqueous and DMSO solutions indicate mixture of mononuclear and binuclear forms. The Cu(II) complexes, together with the corresponding ligands, were evaluated for their trypanocidal activity in vitro against Trypanosoma cruzi, the causative agent of Chagas disease. The assays performed against bloodstream trypomastigotes showed that all complexes were more active than their corresponding ligands. Complexes [CuCl(2)(phen)(LEV)] and [CuCl(2)(phen)(SPAR)] were revealed, among all studied compounds, to be the most active with IC(50)?=?1.6 and 4.7?μM, respectively, both presenting a superior effect than benznidazole. The interactions of fluoroquinolones and their Cu(II) complexes with calf-thymus DNA were investigated. These compounds showed binding properties towards DNA, with moderated binding constants values, suggesting that this structure may represent a parasite target.     

Protein A immobilized polyhydroxyethylmethacrylate beads for affinity sorption of human immunoglobulin G

Protein A immobilized polyhydroxylmethyacrylate (PHEMA) microbeads were investigated for the specific removal of HIgG from aqueous solutions and from human plasma. PHEMA microbeads were prepared by a suspension polymerization technique and activated by CNBr in an alkaline medium (pH 11.5). Protein A was then immobilized by covalent binding onto these microbeads. The amount of immobilized protein A was controlled by changing pH and the initial concentrations of CNBr and protein A. The maximum protein A immobilization was observed at pH 9.5. Up to 3.5 mg protein A/g PHEMA was immobilized on the CNBr activated PHEMA microbeads. The maximum HIgG adsorption on the protein A immobilized PHEMA microbeads was observed at pH 8.0. The non-specific HIgG adsorption onto the plain PHEMA microbeads was low (about 0.167 mg of HIgG/g PHEMA). Higher adsorption values (up to 6.0 mg of HIgG/g PHEMA) were obtained in which the protein A immobilized PHEMA microbeads were used. Much higher amounts of HIgG (up to 24.0 mg of HIgG/g PHEMA) were adsorbed from human plasma.     

Polymer composites reinforced by locking-in a liquid-crystalline assembly of cellulose nanocrystallites

An attempt was made to synthesize novel composites comprising poly(2-hydroxyethyl methacrylate) (PHEMA) and cellulose nanocrystallites (CNC) (acid-treated cotton microfibrils) from suspensions of CNC in an aqueous 2-hydroxyethyl methacrylate (HEMA) monomer solution. The starting suspensions (～5 wt % CNC) separated into an isotropic upper phase and an anisotropic bottom one in the course of quiescent standing. By way of polymerization of HEMA in different phase situations of the suspensions, we obtained films of three polymer composites, PHEMA-CNC(iso), PHEMA-CNC(aniso), and PHEMA-CNC(mix), coming from the isotropic phase, anisotropic phase, and embryonic nonseparating mixture, respectively. All the composites were transparent and, more or less, birefringent under a polarized optical microscope. A fingerprint texture typical of cholesteric liquid crystals of longer pitch spread widely in PHEMA-CNC(aniso) but rather locally appeared in PHEMA-CNC(iso). Any of the CNC incorporations into the PHEMA matrix improved the original thermal and mechanical properties of this amorphous polymer material. In dynamic mechanical measurements, the locking-in of the respective CNC assemblies gave rise to an increase in the glass-state modulus E' of PHEMA as well as a marked suppression of the E'-falling at temperatures higher than T(g) (≈ 110 °C) of the vinyl polymer. It was also observed for the composites that their modulus E' rerose in a range of about 150-190 °C, which was attributable to a secondary cross-linking formation between PHEMA chains mediated by the acidic CNC filler. The mechanical reinforcement effect of the CNC dispersions was ensured in a tensile test, whereby PHEMA-CNC(aniso) was found to surpass the other two composites in stiffness and strength.     

Selective separation of human serum albumin with copper(II) chelated poly(hydroxyethyl methacrylate) based nanoparticles

Poly(hydroxyethyl methacrylate) (PHEMA) nanoparticles with an average size of 300 nm in diameter and with a polydispersity index of 1.156 were produced by surfactant free emulsion polymerization. Specific surface area of the PHEMA nanoparticles was found to be 996 m²/g. Metal-chelating ligand 3-(2-imidazoline-1-yl)propyl(triethoxysilane) (IMEO) was covalently attached to the PHEMA nanoparticles. IMEO content was 0.97 mmol IEMO/g. The morphology and properties of these nanoparticles were characterized with scanning electron microscopy, Fourier transform infrared spectroscopy and atomic force microscopy. The Cu²⁺-chelated PHEMA–IMEO nanoparticles were used in the adsorption-elution studies of human serum albumin (HSA) in a batch system. Maximum HSA adsorption amount of the Cu²⁺ chelated nanoparticles was 680 mg HSA/g. The PHEMA–IMEO–Cu²⁺ nanoparticles exhibited a quite high adsorption capacity and fast adsorption rate due to their high specific surface area and the absence of internal diffusion resistance.     

NMR imaging of the diffusion of water at 37 degrees C into Poly(2-hydroxyethyl methacrylate) containing aspirin or vitamin B(12)

The ingress of water into poly(2-hydroxyethyl methacrylate), PHEMA, loaded with either one of two model drugs, vitamin B(12) or aspirin, was studied at 37 degrees C using three-dimensional NMR imaging. PHEMA was loaded with 5 and 10 wt % of the drugs. From the imaging profiles, it was observed that incorporation of vitamin B(12) into PHEMA resulted in enhanced crack formation on sorption of water and the crack healing behind the diffusion front was slower than for PHEMA without added drug. This was accounted for by the anti-plasticization of PHEMA by vitamin B(12). Crack formation was inhibited in the PHEMA-aspirin systems because of the plasticizing effect of the aspirin on the PHEMA matrix. All of the polymers were found to absorb water according to an underlying Fickian diffusion mechanism. For PHEMA loaded with 5 wt % of aspirin or vitamin B(12), the best values of the water diffusion coefficients were both found to be 1.3 +/- 0.1 x 10(-11) m(2) s(-1) at 37 degrees C, while the values for the polymer loaded with 10 wt % of the drugs were slightly higher, 1.5 +/- 0.1 x 10(-11) m(2) s(-1).