Development of fructosyl valine binding polymers by covalent imprinting

Molecularly imprinted polymers (MIPs) against fructosyl valine (Fru-Val), the N-terminal constituent of hemoglobin A1c β-chains, were prepared by cross-linking of β-d-Fru-Val-O-bis(4-vinylphenylboronate) with an excess of ethylene glycol dimethacrylate (EDMA) or trimethylolpropane trimethacrylate (TRIM). Control MIPs were prepared in analogy by cross-linking the corresponding vinylphenylboronate esters of fructose and pinacol. After template extraction batch rebinding studies were performed using different pH values and buffer compositions. The Fru-Val imprinted TRIM cross-linked polymer binds about 1.4 times more Fru-Val than the fructose imprinted polymer and 2.7 times more Fru-Val than pinacol imprinted polymer. The highest imprinting effect was obtained in 100 mM sodium carbonate/10% methanol (pH 11.4). The TRIM cross-linked Fru-Val imprinted polymer showed a better specificity than the EDMA cross-linked polymer. The binding of valine was very low. Thermo gravimetric analysis indicated that the generated Fru-Val imprinted polymer has high thermo stability. No change in binding was observed after incubation of the polymers in buffer at 80 °C for 36 h. Since the functional group of the polymers (phenyl boronic acid) targets the sugar part of Fru-Val the imprint technique used should also be applicable for the development of MIPs against other glycated amino acids and peptides.     

Molecularly imprinted polymer using-p-hydroxybenzoic acid, p-hydroxyphenylacetic acid and p-hydroxyphenylpropionic acid as templates.

Molecularly imprinted polymers (MIPs) using p-hydroxybenzoic acid (p-HB), p-hydroxyphenylacetic acid (p-HPA) and p-hydroxyphenylpropionic acid (p-HPPA) as templates were synthesized. The performance of the templates and their analogues on polymer-based high performance liquid chromatography (HPLC) columns was studied. The imprinting effect of the MIP using p-HB as template is more obvious than that of MIP using either p-HPA or p-HPPA as template, and the mixture of p-HB and p-HPA can be well separated on the MIP using p-HB as template, but not on the blank. Interestingly, the recognition of MIP (p-HB as the template) to p-HB showed a synergistic effect. The retention factor of p-HB is not the sum of those of phenol and benzoic acid. We also found that the imprinting effect decreased when increasing the concentration of acetic acid in mobile phase. The possible reason is that acetic acid molecules occupied the binding sites of the polymer, thereby decreasing the concentration of binding sites. Furthermore, polymers, which showed specificity to 3,4-dihydroxybenzoic acid, can be prepared with p-HB as template. It is thus possible to synthesize a specific polymer for a compound that is either expensive or unstable by using a structurally similar compound as template.     

Molecularly imprinted polymers (MIP) in electroanalysis of proteins

The review summarizes current knowledge on the main approaches used for creation of high affinity polymer analogs of antibodies (known as molecularly imprinted polymers, MIP) applicable for electroanalysis of functionally important proteins such as myoglobin, troponin T, albumin, ferritin, lysozyme, calmodulin. The main types of monomers for MIP preparation as well as methods convenient for analysis of MIP/protein interactions, such as surface plasmon resonance (SPR), nanogravimetry with the use of a quartz crystal resonator (QCM), spectral and electrochemical methods have been considered. Special attention is paid to experimental data on electrochemical registration of myoglobin by means of o-phenylenediaminebased MIP electrodes. It was shown that the imprinting factor calculated as a ratio of the myoglobin signal obtained after myoglobin insertion in MIP to the myoglobin signal obtained after myoglobin insertion in the polymer lacking the molecular template (NIP) is 2–4.     

Novel biphasic separations utilising highly selective molecularly imprinted polymers as biorecognition solvent extraction agents

Molecularly imprinted polymers (MIPs) represent a class of artificial receptors that promise an environmentally robust alternative to naturally occurring biorecognition elements of biosensing devices and systems. However, in general, the performance of conventional MIPs in aqueous environments is poor. In the study reported here, this limitation has been addressed by the novel application of MIPs as a solvent extraction solid phase in a biphasic solvent system. This paper describes a previously unreported use of MIPs as solvent extraction reagents, their successful application to aqueous sample media and the opportunities for utilisation of this unique system in novel biosensing and separation procedures. This study demonstrates the development of a novel biphasic solvent system utilising MIP in the extracting phase to enhance both efficiency and selectivity of a simple two phase liquid extraction. Monodisperse propranolol imprinted polymer microspheres [p(divinylbenzene-co-methacrylic acid)] were prepared by precipitation polymerisation. Initially, the affinity of the polymers for (R,S)-propranolol was assessed by established techniques whereby the MIP demonstrated greater affinity for the template than did the non-imprinted control polymer (NIP). Importantly, MIP performance was also assessed using the novel dual solvent system. The depletion of (R,S)-propranolol from the aqueous phase into the polymer containing organic phase was determined. When compared to control extractions containing no polymer the presence of MIP in the extracting solvent phase resulted in an increased extraction of (R,S)-propranolol from the aqueous phase. Importantly, this extraction was significantly greater in the presence of MIP when compared to NIP. This unique principle generates opportunities for MIP based extractions and chemical enrichments in industrial applications, offering commercial, ecological and practical advantages to traditional solvent extraction techniques. The technique is readily transferable to analytical microsystems utilising MIP recognition elements generating promising opportunities for MIP based sensing of aqueous sample media.     

Peptide boronic acids, substrate analogs, inhibit chymase, and histamine release from rat mast cells

Peptide boronic acids, such as methoxysuccinyl-Ala-Ala-Pro-(L)boro-Phe-OH, its pinacol ester, and t-butyloxycarbonyl-Phe-Pro-(L)boro-Phe-pinacol, inhibited the activity of chymase from connective tissue mast cells approximately 40- to 80-fold more than atypical chymase from mucosal mast cells, and did not inhibit trypsin. Only peptide boronic acids containing "L" forms of boronic acids were inhibitory. The Ki values of these peptide boronic acids for chymase were in the 60-170 nM concentration range, like those of the natural inhibitors tested, but all the natural inhibitors tested except Eglin C and chymostatin inhibited both chymase and trypsin. Thus these peptide boronic acids should be useful for selective inhibition of chymase with less inhibitory activity for atypical chymase and without inhibition of trypsin. These peptide boronic acids markedly inhibited histamine release induced by anti-rat immunoglobulin E, suggesting that chymase in connective tissue mast cells plays some role in the process of histamine release. These peptides are assumed to be therapeutically useful for treatment of allergic inflammations catalyzed by chymase.     

Molecularly imprinted polymer-assisted refolding of lysozyme

For production of active proteins using heterologous expression systems, refolding of proteins from inclusion bodies often creates a bottleneck due to its poor yield. In this study, we show that molecularly imprinted polymer (MIP) toward native lysozyme promotes the folding of chemically denatured lysozyme. The MIP, which was prepared with 1 M acrylamide, 1 M methacrylic acid, 1 M 2-(dimethylamino)ethyl methacrylate, and 5 mg/mL lysozyme, successfully promoted the refolding of lysozyme, whereas the non-imprinted polymer did not. The refolding yield of 90% was achieved when 15 mg of the MIP was added to 0.3 mg of the unfolded lysozyme. The parallel relationship between the refolding yield and the binding capacity of the MIP suggests that MIP promotes refolding through shifting the folding equilibrium toward the native form by binding the refolded protein.     

Synthesis and evaluation of a selective molecularly imprinted polymer for the contraceptive drug levonorgestrel

A molecularly imprinted polymer (MIP) has been prepared using levonorgestrel (LEV) as template. The polymer was synthesised in a non-covalent approach using methacrylic acid (MAA) as functional monomer and ethylene glycol dimethacrylate (EGDMA) as cross-linking monomer via a free radical polymerization. An equivalent blank polymer was also synthesised in the absence of the template compound. Batch adsorption experiments were used to evaluate the binding affinity of the imprinted polymer. After packing MIP into a stainless steel column (150 mm x 4.6 mm i.d.), retention and elution of the template and related compounds were evaluated by high-performance liquid chromatography (HPLC). This LEV imprinted polymer was further applied for selective solid phase extraction (SPE) of LEV from human serum. It was confirmed that the binding ability of the prepared MIP for LEV was essentially sufficient in the presence of other compounds coexisting in serum sample. Therefore, as a selective and efficient solid phase material, LEV imprinted polymer has a high potential application in analysis of this steroidal hormone in clinical purposes.     

Development of molecularly imprinted polymers as tailored templates for the solid-state [2+2] photodimerization

In this study, a molecularly imprinted polymer (MIP) was prepared to selectively template the [2+2] photodimerization of trans-1,2-bis(4-pyridyl)ethylene. First, an MIP selective for rctt-tetrakis(4-pyridyl)cyclobutane, which is the [2+2] photodimerization product of trans-1,2-bis(4-pyridyl)ethylene, was prepared from methacrylic acid (MAA) and ethylene glycol dimethacrylate (EGDMA). The non-covalent MIP showed enhanced affinity for both the templating agent, rctt-tetrakis(4-pyridyl)cyclobutane, and the alkene precursor, trans-1,2-bis(4-pyridyl)ethylene. The solid-state photodimerization reaction proceeded in significantly higher yields in the presence of the MIP. Control reactions carried out in the absence of polymer gave no product, and reactions carried out in the presence of a non-imprinted polymer and an MIP imprinted with a different template, 3-hydroxymethylpyridine, gave much lower yields of the cyclobutane photodimerization product. The outcome of the MIP-templated photodimerization reaction was strongly influenced by the binding site heterogeneity of the non-covalently imprinted polymers. For example, higher yields were observed with decreasing olefin loadings levels on the MIPs. This binding site heterogeneity was characterized via application of the Freundlich binding model to the experimentally measured binding isotherms. These confirmed that the non-covalent MIPs had very few high-affinity binding sites, which greatly limits the capacity and ultimately the utility of these materials as templates in synthetic organic applications.     

Novel fluorescent sensing system for alpha-fructosyl amino acids based on engineered fructosyl amino acid binding protein

A novel fluorescent sensing system for alpha-glycated amino acids was created based on fructosyl amino acid binding protein (FABP) from Agrobacterium tumefaciens. The protein was found to bind specifically to the alpha-glycated amino acids fructosyl glutamine (Fru-Gln) and fructosyl valine (Fru-Val) while not binding to epsilon-fructosyl lysine. An Ile166Cys mutant of FABP was created by genetic engineering and modified with the environmentally sensitive fluorophore acrylodan. The acrylodan-conjugated mutant FABP showed eight-fold greater sensitivity to Fru-Val than the unconjugated protein and could detect concentrations as low as 17 nM, making it over 100-fold more sensitive than enzyme-based detection systems. Its high sensitivity and specificity for alpha-substituted fructosyl amino acids makes the new sensing system ideally suited for the measurement of hemoglobin A1c (HbA1c), a major marker of diabetes.     

Molecularly imprinted polymers—A closer look at the control polymer used in determining the imprinting effect: A mini review

Molecular recognition displayed by naturally occurring receptors has continued to inspire new innovations aimed at developing systems that can mimic this natural phenomenon. Since 1930s, a technology called molecular imprinting for producing biomimetic receptors has been in place. In this technology, tailor made binding sites that selectively bind a given target analyte (also called template) are incorporated in a polymer matrix by polymerizing functional monomers and cross‐linking monomers around a target analyte followed by removal of the analyte to leave behind cavities specific to the analyte. The success of the imprinting process is defined by two main figures of merit, that is, the imprinting factor, and selectivity, which are determined by comparing the amount of target analyte or structural analogue bound by the molecularly imprinted polymer (MIP) and the nonimprinted polymer (NIP). NIP is a control synthesized alongside the MIP but in the absence of the template. However, questions arise on whether these figures of merit are reliable measures of the imprinting effect because of the significant differences between the MIP and the NIP in terms of their physical and chemical characteristics. Therefore, this review critically looks into this subject, with a view of defining the best approaches for determining the imprinting effect.     

Subsite specificity of divalent metal ions to glucosyltransferase

Glucosyltransferase from oral bacteria Streptococcus mutans is the most significant virulent factor in causing dental caries. The enzyme has two subsites. The binding specificity of divalent metal ions to glucosyl or fructosyl subsite was examined using multiple inhibition kinetics. The interaction factor "alpha" identifies whether the two subsites are exclusive or non-exclusive.     

A molecularly imprinted polymer on indium tin oxide and silicon

Molecular imprinting is a technique for creating artificial receptor sites in a polymer. Molecularly imprinted polymers (MIPs) are produced by forming a polymer around a molecule that is used as the template. Upon removal of the template, molecular holes remain which are specific in shape and size to the target molecule. In this research, a MIP was formed for theophylline using a copolymer of methacrylic acid and ethylene glycol dimethacrylate. The theophylline MIP was formed on two platforms: indium tin oxide (ITO) and silicon, which were used as the working electrode for cyclic voltammetry measurements. The presence of theophylline was measured using cyclic voltammetry and corresponded to the peak current on the cyclic voltammograms. The results of this research agreed with previous results of MIPs immobilized on an ITO platform. The peak currents of the MIP in the presence and absence of theophylline were compared to the blank polymer for each platform. The ratio of peak currents on ITO increased by a factor of 9.5 for the MIP compared to the non-imprinted polymer. Similarly, the ratio of peak currents on silicon increased by a factor of 6 compared to the non-imprinted polymer. This research demonstrated a procedure for evaluating a MIP layer on two different platforms.     

Molecularly imprinted polymer-assisted sample clean-up of ochratoxin A from red wine: merits and limitations

A new analytical method for the determination of the carcinogenic mycotoxin ochratoxin A (OTA) in red wines has been developed involving a two-dimensional solid-phase extraction (SPE) clean-up protocol on C18-silica and a target-selective molecularly imprinted polymer (MIP). Prior removal of the interfering acidic matrix compounds by C18 solid-phase extraction was crucial for a successful clean-up as direct sample loading onto the MIP led to poor recoveries. The combined solid-phase extraction protocol afforded extracts suitable for sensitive ochratoxin A quantification by HPLC-fluorescence detection. Preliminary validation of the method performance with spiked (0.033-1.0 ng OTA/ml) and commercial red wines provided recoveries >90% and < 10%, with limit of detection (LOD) and limit of quantification (LOQ) of 0.01 and 0.033 ng/ml. However, a similarly favorable performance characteristics was observed in control experiments in which the MIP was replaced by the corresponding non-imprinted polymer (NIP). These findings provide evidence that under the employed experimental conditions specific analyte binding to imprinted binding sites plays a minor role in selective OTA retention. In the framework of this study, other problems inherent to MIP-based solid-phase extraction have been addressed. These include the reproducible preparation of MIP materials with consistent molecular recognition characteristics, the potential for repeated use of MIP, unfavorable polymer swelling in application-relevant solvents, potential sample contamination by template bleeding, and slow analyte binding kinetics.     

Application of Molecularly Imprinted Polymers to Selective Removal of Clofibric Acid from Water

A new molecularly imprinted polymer (MIP) adsorbent for clofibric acid (CA) was prepared by a non-covalent protocol. Characterization of the obtained MIP was achieved by scanning electron microscopy (SEM) and nitrogen sorption. Sorption experimental results showed that the MIP had excellent binding affinity for CA and the adsorption of CA by MIP was well described by pseudo-second-order model. Scatchard plot analysis revealed that two classes of binding sites were formed in the MIP with dissociation constants of 7.52±0.46 mg L⁻¹ and 114±4.2 mg L⁻¹, respectively. The selectivity of MIP demonstrated higher affinity for CA over competitive compound than that of non-imprinted polymers (NIP). The MIP synthesized was used to remove CA from spiked surface water and exhibited significant binding affinity towards CA in the presence of total dissolved solids (TDS). In addition, MIP reusability was demonstrated for at least 12 repeated cycles without significant loss in performance.     

Synthesis and evaluation of uniformly sized nalidixic acid-imprinted nanospheres based on precipitation polymerization method for analytical and biomedical applications

For the first time in this work, uniform molecularly imprinted polymer (MIP) nanoparticles were prepared using nalidixic acid as a template. The MIP nanoparticles were successfully synthesized by precipitation polymerization applying methacrylic acid (MAA) as a functional monomer and trimethylolpropane trimethacrylate (TRIM) as a cross-linking monomer at different mole ratios. The morphology, binding, recognition, selectivity, and in vitro release behaviors of obtained particles were studied. The produced polymers were characterized by Fourier transform infrared spectroscopy and differential scanning calorimetric. Furthermore, their morphology was analyzed accurately by scanning electron microscopy, photon correlation spectroscopy, and Brunauer-Emmett-Teller analysis. The nanospheres and microspheres with mean diameter values of 94 nm, 256 nm, and 1.2 μm were obtained using nalidixic acid-MAA-TRIM various mole ratios. Among the MIPs, the product with nalidixic acid-MAA-TRIM mole ratio of 1:12:12 established nanospheres with the lowest polydispersity index (0.003), an average pore diameter (12 nm), and the highest specific surface area (280 m(2) g(-1)) and selectivity factor (10.4). Results from binding experiments demonstrated that the imprinted nanospheres with a 94-nm mean diameter and a binding capacity of 28 mg of nalidixic acid per gram of polymer had higher specific affinity to nalidixic acid in contrast with the other imprinted nanospheres, microspheres, and nonimprinted particles. However, the binding performance of imprinted nanospheres in human serum was estimated using high-performance liquid chromatography analysis (binding approximately 98% of nalidixic acid). In addition, release experiments proved to be successful in the controlled release of nalidixic acid during a long period. The 20% of loaded nalidixic acid was released from the imprinted nanospheres within the first 20 h, whereas the remaining 80% was released in the after 120 h. The nalidixic acid release kinetics from the MIPs was highly affected by properties of the particles.     

Effect of polymers on enhanced chemiluminescent assays for peroxidase and peroxidase labels

Hydroxypropyl methylcellulose, hydroxyethyl cellulose, and hydroxybutyl methylcellulose stabilized light emission in a boronic acid-enhanced chemiluminescent assay for horseradish peroxidase. The stabilization of light emission was concentration-dependent and more effective with substituted boronic acid enhancers (e.g. 4-iodophenylboronic acid) than with substituted phenol enhancers (e.g. 4-iodophenol). Hydroxybutyl methylcellulose improved the linearity of the dose–response curve in a peroxidase-based antioxidant assay and stabilized light emission post-consumption of the antioxidant (Trolox). This polymer had no effect on the signal from a peroxidase label immobilized on a membrane (dot blot) or on the inside surface of a microwell in an enzyme immunoassay for thyrotropin.     

Binding cross-reactivity of Boc-phenylalanine enantiomers on molecularly imprinted polymers

A potential problem associated with molecularly imprinted polymer (MIP) sorbents is that of cross-reactivity. In this study three MIPs (imprinted with Boc-L-phenylalanine, Boc-L-alanine, Boc-L-glutamic acid) plus a non-imprinted control were prepared and examined for their ability to bind differentially the enantiomers of boc-protected phenylalanine in an effort to quantify cross-reactivity and to develop a predictive model. Batch rebinding studies showed a degree of predictability for a number of MIP-ligand pairs, but other combinations showed unexpectedly high levels of cross-reactivity. Despite the general acceptance of heterogeneity of MIP binding sites, many previous studies report linear Scatchard plots, which is indicative of binding site homogeneity. The data from this study produced curves, clearly demonstrating heterogeneity. The theoretical and practical implications of this heterogeneity are discussed. Chirality 9:233–237, 1997. © 1997 Wiley-Liss, Inc.     

SocA is a novel periplasmic binding protein for fructosyl amino acid

Bacterial periplasmic proteins (bPBPs) undergo drastic conformational changes upon binding substrate, making them appealing as novel molecular recognition tools for biosensing. A putative bPBP-encoding gene, socA, belongs to the soc operon responsible for santhopine (fructosyl glutamine, FQ) catabolism of Agrobacterium tumefaciens. The socA gene was isolated and expressed in Escherichia coli as a soluble 28.8kDa periplasmic protein to investigate its properties as a potential bPBP for fructosyl amino acid (FA). The autofluorescence of SocA was used to monitor the protein's conformational change resulting from substrate binding. The fluorescence intensity changed upon binding FQ in a concentration dependent manner with a calculated K(d) of 2.1muM, but was unaffected by the presence of sugars or amino acid. Our results demonstrate that SocA is a novel FA bPBP that can be utilized as a novel molecular recognition element for the monitoring of FA.     

Development of molecularly imprinted polymers for the binding of nitrofurantoin

Novel molecularly imprinted polymers (MIPs) for the recognition of nitrofurantoin (NFT) were prepared by photoinitiated polymerisation in polar solvent using 2,6-bis(methacrylamido) pyridine (BMP) as the functional monomer and carboxyphenyl aminohydantoin (CPAH) as the analogue of the template. The binding constants of the complex between BMP and nitrofurantoin or CPAH in DMSO were determined with 1H NMR titration to be 630 ± 104 and 830 ± 146 M⁻¹, respectively. To study the influence of the functional monomer, two polymer compositions were prepared containing the template, the functional monomer and the crosslinker in the molar ratio 1:1:12 for MIP1 and 1:4:20 for MIP2, respectively. The imprinting factor at saturation concentration of nitrofurantoin, which is the ratio of the amount bound to the MIP and the non-imprinted control polymer (NIP), was determined to be 2.47 for MIP1 and 2.49 for MIP2. The cross reactivity of the imprinted polymers seems to be determined by the ability to form hydrogen bonds to the functional monomer while the shape of the molecule has no real influence.     

Probing the general time scale question of boronic acid binding with sugars in aqueous solution at physiological pH

The boronic acid group is widely used in chemosensor design due to its ability to reversibly bind diol-containing compounds. The thermodynamic properties of the boronic acid-diol binding process have been investigated extensively. However, there are few studies of the kinetic properties of such binding processes. In this report, stopped-flow method was used for the first time to study the kinetic properties of the binding between three model arylboronic acids, 4-, 5-, and 8-isoquinolinylboronic acids, and various sugars. With all the boronic acid-diol pairs examined, reactions were complete within seconds. The k(on) values with various sugars follow the order of D-fructose>D-tagatose>D-mannose>D-glucose. This trend tracks the thermodynamic binding affinities for these sugars and demonstrates that the 'on' rate is the key factor determining the binding constant.