Simple,Highly Efficient Vacuum‐Processed Bulk Heterojunction Solar Cells Based on Merocyanine Dyes

In order to be competitive on the energy market, organic solar cells with higher efficiency are needed. To date, polymer solar cells have retained the lead with efficiencies of up to 8%. However, research on small molecule solar cells has been catching up throughout recent years and is showing similar efficiencies, however, only for more sophisticated multilayer device configurations. In this work, a simple, highly efficient, vacuum‐processed small molecule solar cell based on merocyanine dyes – traditional colorants that can easily be mass‐produced and purified – is presented. In the past, merocyanines have been successfully introduced in solution‐processed as well as vacuum‐processed devices, demonstrating efficiencies up to 4.9%. Here, further optimization of devices is achieved while keeping the same simple layer stack, ultimately leading to efficiencies beyond the 6% mark. In addition, physical properties such as the charge carrier transport and the cell performance under various light intensities are addressed.     

ITO‐Free and Fully Solution‐Processed Semitransparent Organic Solar Cells with High Fill Factors

Organic photovoltaic (OPV) solar cells that can be simply processed from solution are in the focus of the academic and industrial community because of their enormous potential to reduce cost. One big challenge in developing a fully solution‐processed OPV technology is the design of a well‐performing electrode system, allowing the replacement of ITO. Several solution‐processed electrode systems were already discussed, but none of them could match the performance of ITO. Here, we report efficient ITO‐free and fully solution‐processed semitransparent inverted organic solar cells based on silver nanowire (AgNW) electrodes. To demonstrate the potential of these AgNW electrodes, they were employed as both the bottom and top electrodes. Record devices achieved fill factors as high as 63.0%, which is comparable to ITO based reference devices. These results provide important progress for fully printed organic solar cells and indicate that ITO‐free, transparent as well as non‐transparent organic solar cells can indeed be fully solution‐processed without losses.     

Improved Performance and Stability of Inverted Organic Solar Cells with Sol–Gel Processed,Amorphous Mixed Metal Oxide Electron Extraction Layers Comprising Alkaline Earth Metals

Stability of organic photovoltaic devices (OPVs) is a limiting factor for their commercialization and still remains a major challenge whilst power conversion efficiencies are now approaching minimum requirements. The inverted organic solar cell (iOSC) architecture shows promising potential for improving significantly the cell's working lifetime. However, when solution processed ZnO is used as electron extraction layer, an undesirable light‐soaking step is commonly required before the device reaches a non‐permanent maximum performance. This work investigates the use of Sr and Ba doped ZnO films, ZnSrO and ZnBaO, formed by sol‐gel deposition using molecular alkoxide precursor solutions, as electron extraction layers in a model iOSCs with poly [3‐hexylthiophene] (P3HT): [6, 6]‐phenyl C60 butyl acid methyl ester (PCBM) as the active layer. We show that using these ternary oxides the light‐soaking step can be circumvented by preventing a dipole forming between the oxide and the active organic layer as supported by electroabsorption spectroscopy measurements of the device built‐in field. It is suggested that Sr or Ba doping results in suppression/reduction of the oxygen adsorption at mobile oxygen vacancy sites on the metal oxide surface. Like in thin film transistor (TFT) applications, where materials like InGaZnO are rapidly becoming an important technology, the use of amorphous, mixed metal oxides allows improving the performance and stability of interfacial charge extraction layers for organic solar cells.     

Perovskite Solar Cells on the Way to Their Radiative Efficiency Limit – Insights Into a Success Story of High Open‐Circuit Voltage and Low Recombination

Inorganic‐organic lead‐halide perovskite solar cells have reached efficiencies above 22% within a few years of research. Achieved photovoltages of >1.2 V are outstanding for a material with a bandgap of 1.6 eV – in particular considering that it is solution processed. Such values demand for low non‐radiative recombination rates and come along with high luminescence yields when the solar cell is operated as a light emitting diode. This progress report summarizes the developments on material composition and device architecture, which allowed for such high photovoltages. It critically assesses the term “lifetime”, the theories and experiments behind it, and the different recombination mechanisms present. It attempts to condense reported explanations for the extraordinary optoelectronic properties of the material. Amongst those are an outstanding defect tolerance due to antibonding valence states and the capability of bandgap tuning, which might make the dream of low‐cost highly efficient solution‐processed thin film solar cells come true. Beyond that, the presence of photon recycling will open new opportunities for photonic device design.     

Hybrid Perovskites: Effective Crystal Growth for Optoelectronic Applications

Outstanding material properties of organic‐inorganic hybrid perovskites have triggered a new insight into the next‐generation solar cells. Beyond solar cells, a wide range of controllable properties of hybrid perovskites, particularly depending on crystal growth conditions, enables versatile high‐performance optoelectronic devices such as light‐emitting diodes, photodetectors, and lasers. This article highlights recent progress in the crystallization strategies of organic–inorganic hybrid perovskites for use as effective light harvesters or light emitters. Fundamental background on perovskite crystalline structures and relevant optoelectronic properties such as optical band‐gap, electron‐hole behavior, and energy band alignment are given. A detailed overview of the effective crystallization methods for perovskites, including thermal treatment, additives, solvent mediator, laser irradiation, nanostructure, and crystal dimensionalityis reported offering a comprehensive correlation among perovskite processing conditions, crystalline morphology, and relevant device performance. Finally, future research directions to overcome current practical bottlenecks and move towards reliable high performance perovskite optoelectronic applications are proposed.     

Aqueous‐Processed Polymer/Nanocrystal Hybrid Solar Cells with Double‐Side Bulk Heterojunction

Aqueous‐solution‐processed solar cells (ASCs) are promising candidates of the next‐generation large‐area, low‐cost, and flexible photovoltaic conversion equipment because of their unique environmental friendly property. Aqueous‐solution‐processed polymer/nanocrystals (NCs) hybrid solar cells (AHSCs) can effectively integrate the advantages of the polymer (e.g., flexibility and lightweight) and the inorganic NCs (e.g., high mobility and broad absorption), and therefore be considered as an ideal system to further improve the performance of ASCs. In this work, double‐side bulk heterojunction (BHJ), in which one BHJ combines the active material with electron transport material and the other combines the active material with hole transport material, is developed in the AHSCs. Through comparing with the single‐side BHJ device, promoted carrier extraction, enhanced internal quantum efficiency, extended width of the depletion region, and prolonged carrier lifetime are achieved in double‐side BHJ devices. As a result, power conversion efficiency exceeding 6% is obtained, which breaks the bottleneck efficiency around ≈5.5%. This work demonstrates a device architecture which is more remarkable compared with the traditional only donor–acceptor blended BHJ. Under conservative estimation, it provides instructive architecture not only in the ASCs, but also in the organic solar cells (SCs), quantum dot SCs, and perovskite SCs.     

π‐Extended Narrow‐Bandgap Diketopyrrolopyrrole‐Based Oligomers for Solution‐Processed Inverted Organic Solar Cells

A series of narrow‐bandgap π‐conjugated oligomers based on diketopyrrolopyrrole chromophoric units coupled with benzodithiophene, indacenodithiophene, thiophene, and isoindigo cores are designed and synthesized for application as donor materials in solution‐processed small‐molecule organic solar cells. The impacts of these different central cores on the optoelectronic and morphological properties, carrier mobility, and photovoltaic performance are investigated. These π‐extended oligomers possess broad and intense optical absorption covering the range from 550 to 750 nm, narrow optical bandgaps of 1.52–1.69 eV, and relatively low‐lying highest occupied molecular orbital (HOMO) energy levels ranging from ?5.24 to ?5.46 eV in their thin films. A high power conversion efficiency of 5.9% under simulated AM 1.5G illumination is achieved for inverted organic solar cells based on a small‐molecule bulk‐heterojunction system consisting of a benzodithiophene‐diketopyrrolopyrrole‐containing oligomer as a donor and [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) as an acceptor. Transmission electron microscopy and energy‐dispersive X‐ray spectroscopy reveal that interpenetrating and interconnected donor/acceptor domains with pronounced mesoscopic phase segregation are formed within the photoactive binary blends, which is ideal for efficient exciton dissociation and charge transport in the bulk‐heterojunction devices.     

Unraveling Charge Separation and Transport Mechanisms in Aqueous‐Processed Polymer/CdTe Nanocrystal Hybrid Solar Cells

Recently great progress has been achieved in highly effective hybrid solar cells fabricated using aqueous materials. The state‐of‐the‐art energy conversion efficiency has been close to 5% with high photocurrent. However, charge separation and transport mechanism in the aqueous‐processed hybrid solar cells are rarely reported and are usually assumed to be similar to oil‐phase processed systems; that is, self‐assembly polymers are mainly responsible for charge separation and carrier transport. To date, this assumption has prohibited further improvement of the conversion efficiency in aqueous‐processed hybrid systems by adopting any appropriate technique routes. Here, ultrafast carrier dynamics in these hybrid solar cells consisting of poly(p‐phenylenevinylene) (PPV)‐based aqueous polymers and water‐solution CdTe nanocrystals (NCs) are investigated in detail. Self‐charge separation in grown CdTe NC partly capped CdS shell layers after anneal treatment is unambiguously identified. Different from their oil‐soluble counterparts, these core/shell nanocrystals do not have the restrictions of quantum confinement and surface ligands, form effective charge transport networks, and play a dominant role in the charge separation and carrier transport processes. These findings provide a greater understanding on the fundamental photophysics in aqueous‐processed hybrid systems.     

Highly Efficient Aqueous‐Processed Hybrid Solar Cells: Control Depletion Region and Improve Carrier Extraction

Environmental friendly aqueous‐processed solar cells have become one of the most promising candidates for the next‐generation photovoltaic devices. Researchers have made lots of progress in designing active materials with novel structures, manipulating the defects in active materials, optimizing device architecture, etc. However, it has long been a challenge to control the width of the depletion region and enhance carrier extraction ability. Fabrication of a thick bulk heterojunction (BHJ) film is an effective strategy to address these issues but difficult to realize. Herein, the thicker BHJ film of ZnO:CdTe is successfully fabricated and incorporated into CdTe‐poly(p‐phenylenevinylene) hybrid solar cells. As expected, this BHJ film enhances light absorption, extends the width of the depletion region, prolongs carrier lifetime, and promotes carrier extraction ability. Moreover, the electron transport layer of sol–gel ZnO with excellent transmittance and electrical conductivity boosts electron generation, transport, and injection, which further improves the device performance. As a result, the highest short current density (J_sc) of 19.5 mA cm^?2, power conversion efficiency of 6.51%, and the widest depletion region (177 nm) are obtained in aqueous‐processed hybrid solar cells.     

Lateral Organic Solar Cells with Self‐Assembled Semiconductor Nanowires

Solution‐processable organic semiconductor nanowires (NWs) offer a potentially powerful strategy for producing large‐area printed flexible devices. Here, the fabrication of lateral organic solar cells (LOSC) using solution‐processed organic NW blends on a flexible substrate to produce a power source for use in flexible integrated microelectronics is reported. A high photocarrier generation and an efficient charge sweep out are achieved by incorporating 1D self‐assembled poly(3‐hexylthiophene) NWs into the active layer, and an MoO₃ interfacial layer with high work function is introduced to increase the built‐in potential. These structures significantly increase the carrier diffusion/drift length and overall generated photocurrent in the channel. The utility of the LOSCs for high power source applications is demonstrated by using interdigitated electrode patterns that consist of multiple devices connected in parallel or in series. High photovoltage‐producing LOSC modules on plastic substrates for use in flexible optoelectronic devices are successfully fabricated. The LOSCs described here offer a new device architecture for use in highly flexible photoresponsive energy devices.     

Square‐Centimeter‐Sized High‐Efficiency Polymer Solar Cells: How the Processing Atmosphere and Film Quality Influence Performance at Large Scale

Organic solar cells based on two benzodithiophene‐based polymers (PTB7 and PTB7‐Th) processed at square centimeter‐size under inert atmosphere and ambient air, respectively, are investigated. It is demonstrated that the performance of solar cells processed under inert atmosphere is not limited by the upscaling of photoactive layer and the interfacial layers. Thorough morphological and electrical characterizations of optimized layers and corresponding devices reveal that performance losses due to area enlargement are only caused by the sheet resistance of the transparent electrode reducing the efficiency from 9.3% of 7.8% for PTB7‐Th in the condition that both photoactive layer and the interfacial layers are of high layer quality. Air processing of photoactive layer and the interfacial layers into centimeter‐sized solar cells lead to additional, but only slight, losses (<10%) in all photovoltaic parameters, which can be addressed to changes in the electronic properties of both active layer and ZnO layers rather than changes in layer morphology. The demonstrated compatibility of polymer solar cells using solution‐processed photoactive layer and interfacial layers with large area indicates that the introduction of a standard active area of 1 cm² for measuring efficiency of organic record solar cells is feasible. However electric standards for indium tin oxides (ITO) or alternative transparent electrodes need to be developed so that performance of new photovoltaic materials can be compared at square centimeter‐size.     

Self‐Assembly Atomic Stacking Transport Layer of 2D Layered Titania for Perovskite Solar Cells with Extended UV Stability

A novel atomic stacking transporting layer (ASTL) based on 2D atomic sheets of titania (Ti_1?δO₂) is demonstrated in organic–inorganic lead halide perovskite solar cells. The atomically thin ASTL of 2D titania, which is fabricated using a solution‐processed self‐assembly atomic layer‐by‐layer deposition technique, exhibits the unique features of high UV transparency and negligible (or very low) oxygen vacancies, making it a promising electron transporting material in the development of stable and high‐performance perovskite solar cells. In particular, the solution‐processable atomically thin ASTL of 2D titania atomic sheets shows superior inhibition of UV degradation of perovskite solar cell devices, compared to the conventional high‐temperature sintered TiO₂ counterpart, which usually causes the notorious instability of devices under UV irradiation. The discovery opens up a new dimension to utilize the 2D layered materials with a great variety of homostructrual or heterostructural atomic stacking architectures to be integrated with the fabrication of large‐area photovoltaic or optoelectronic devices based on the solution processes.     

Overcoming Electrode‐Induced Losses in Organic Solar Cells by Tailoring a Quasi‐Ohmic Contact to Fullerenes via Solution‐Processed Alkali Hydroxide Layers

It is shown that the performance of inverted organic solar cells can be significantly improved by facilitating the formation of a quasi‐ohmic contact via solution‐processed alkali hydroxide (AOH) interlayers on top of n‐type metal oxide (aluminum zinc oxide, AZO, and zinc oxide, ZnO) layers. AOHs significantly reduce the work function of metal oxides, and are further proven to effectively passivate defect states in these metal oxides. The interfacial energetics of these electron collecting contacts with a prototypical electron acceptor (C₆₀) are investigated to reveal the presence of a large interface dipole and a new interface state between the Fermi energy and the C₆₀ highest occupied molecular orbital for AOH‐modified AZO contacts. These novel interfacial gap states are a result of ground‐state electron transfer from the metal hydroxide‐functionalized AZO contact to the adsorbed molecules, which are hypothesized to be electronically hybridized with the contact. These interface states tail all the way to the Fermi energy, providing for a highly n‐doped (metal‐like) interfacial molecular layer. Furthermore, the strong “light‐soaking” effect is no longer observed in devices with a AOH interface.     

Relation of Nanostructure and Recombination Dynamics in a Low‐Temperature Solution‐Processed CuInS2 Nanocrystalline Solar Cell

The understanding and control of nanostructures with regard to transport and recombination mechanisms is of key importance in the optimization of the power conversion efficiency (PCE) of solar cells based on inorganic nanocrystals. Here, the transport properties of solution‐processed solar cells are investigated using photo‐CELIV (photogenerated charge carrier extraction by linearly increasing voltage) and transient photovoltage techniques; the solar cells are prepared by an in‐situ formation of CuInS₂ nanocrystals (CIS NCs) at the low temperature of 270 °C. Structural and morphological analyses reveal the presence of a metastable CuIn₅S₈ phase and a disordered morphology in the CuInS₂ nanocrytalline films consisting of polycrystalline grains at the nanoscale range. Consistent with the disordered morphology of the CIS NC thin films, the CIS NC devices are characterized by a low carrier mobility. The carrier density dynamic indicates that the recombination kinetics in these devices follows the dispersive bimolecular recombination model and does not fully behave in a diffusion‐controlled manner, as expected by Langevin‐type recombination. The mobility–lifetime product of the charge carriers properly explains the performance of the thin (200 nm) CIS NC solar cell with a high fill‐factor of 64% and a PCE of over 3.5%.     

Impact of Fullerene on the Photophysics of Ternary Small Molecule Organic Solar Cells

Ternary organic solar cells (OSCs) are among the best‐performing organic photovoltaic devices to date, largely due to the recent development of nonfullerene acceptors. However, fullerene molecules still play an important role in ternary OSC systems, since, for reasons not well understood, they often improve the device performance, despite their lack of absorption. Here, the photophysics of a prototypical ternary small‐molecule OSC blend composed of the donor DR3, the nonfullerene acceptor ICC6, and the fullerene derivative PC₇₁BM is studied by ultrafast spectroscopy. Surprisingly, it is found that after excitation of PC₇₁BM, ultrafast singlet energy transfer to ICC6 competes efficiently with charge transfer. Subsequently, singlets on ICC6 undergo hole transfer to DR3, resulting in free charge generation. Interestingly, PC₇₁BM improves indirectly the electron mobility of the ternary blend, while electrons reside predominantly in ICC6 domains as indicated by fast spectroscopy. The improved mobility facilitates charge carrier extraction, in turn leading to higher device efficiencies of the ternary compared to binary solar cells. Using the (photo)physical parameters obtained from (transient) spectroscopy and charge transport measurements, the device's current–voltage characteristics are simulated and it is demonstrated that the parameters accurately reproduce the experimentally measured device performance.     

High‐Performance Semitransparent Tandem Solar Cell of 8.02% Conversion Efficiency with Solution‐Processed Graphene Mesh and Laminated Ag Nanowire Top Electrodes

A high‐performance semitransparent tandem solar cell that uses solution‐processed graphene mesh and laminated Ag NW as a transparent anode and cathode, respectively, is demonstrated. The laminated top electrode can be deposited without causing any damage to the underneath organic solar cells. Power conversion efficiencies of 8.02% and 6.47% are obtained when the light is projected from the solution‐processed graphene mesh and laminated AgNW, respectively. The performance of the tandem cell is found to be comparable to a tandem solar cell fabricated using commercially available indium tin oxide. These findings offer a high‐performance device and open a new pathway in searching for a potential replacement to the frequently used transparent conducting electrodes.     

Linking Vertical Bulk‐Heterojunction Composition and Transient Photocurrent Dynamics in Organic Solar Cells with Solution‐Processed MoOx Contact Layers

It is demonstrated that a combination of microsecond transient photocurrent measurements and film morphology characterization can be used to identify a charge‐carrier blocking layer within polymer:fullerene bulk‐heterojunction solar cells. Solution‐processed molybdenum oxide (s‐MoO_x) interlayers are used to control the morphology of the bulk‐heterojunction. By selecting either a low‐ or high‐temperature annealing (70 °C or 150 °C) for the s‐MoO_x layer, a well‐performing device is fabricated with an ideally interconnected, high‐efficiency morphology, or a device is fabricated in which the fullerene phase segregates near the hole extracting contact preventing efficient charge extraction. By probing the photocurrent dynamics of these two contrasting model systems as a function of excitation voltage and light intensity, the optoelectronic responses of the solar cells are correlated with the vertical phase composition of the polymer:fullerene active layer, which is known from dynamic secondary‐ion mass spectroscopy (DSIMS). Numerical simulations are used to verify and understand the experimental results. The result is a method to detect poor morphologies in operating organic solar cells.     

The Emergence of the Mixed Perovskites and Their Applications as Solar Cells

The halide perovskite (PVSK) materials (with ABX₃ formulation) have emerged as “dream materials” for photovoltaic (PV) applications due to their remarkable physical properties such as high optical absorption coefficient, carrier mobility, long carrier diffusion lengths, etc. These properties have enabled the PV devices to reach higher than 20% power conversion efficiencies (PCE) in record time. The further pursuit of higher PCE and improved stability brings forth increasing interests in so‐called “mixed composition” PVSK materials, consisting of partial substitution of the A, B, and/or X‐sites with alternative elements/molecules of similar size. Herein, we highlight the recent advances in developing mixed PVSK for PVs and their relevant optoelectronic properties. We mainly focus on mixed PVSK materials in the form of polycrystalline thin films, but also discuss nanostructured and two‐dimensional (2D) PVSK materials due to the increasing interest of broad readership. Efforts are exerted to elucidate the design principles of mixed PVSK and fabrication techniques for high performance optoelectronic devices, which help deepen our fundamental understanding of mixed PVSK systems. We hope this review will shed light onto the design and synthesis of mixed PVSK materials to further the progress of PVSK photovoltaics towards higher efficiencies and longer lifetimes.     

The Rise of Textured Perovskite Morphology: Revolutionizing the Pathway toward High‐Performance Optoelectronic Devices

Halide perovskite materials have achieved overwhelming success in various optoelectronic applications, especially perovskite solar cells and perovskite‐based light‐emitting diodes (P‐LEDs), owing to their outstanding optical and electric properties. It is widely believed that flat and mirror‐like perovskite films are imperative for achieving high device performance, while the potential of other perovskite morphologies, such as the emerging textured perovskite, is overlooked, which leaves plenty of room for further breakthroughs. Compared to flat and mirror‐like perovskites, textured perovskites with unique structures, e.g., coral‐like, maze‐like, column‐like or quasi‐core@shell assemblies, are more efficient at light harvesting and charge extraction, thus revolutionizing the pathways toward ultrahigh performance in perovskite‐based optoelectronic devices. Employing a textured perovskite morphology, the record of external quantum efficiency for P‐LEDs is demonstrated as 21.6%. In this research news, recent progress in the utilization of textured perovskite is summarized, with the emphasis on the preparation strategies and prominent optoelectronic properties. The impact of the textured morphology on light harvesting, carrier dynamic management, and device performance is highlighted. Finally, the challenges and great potential of employing these innovative morphologies in fabricating more efficient optoelectronic devices, or creating a new energy harvesting and conversion regime are also provided.     

Balanced Carrier Mobilities: Not a Necessary Condition for High‐Efficiency Thin Organic Solar Cells as Determined by MIS‐CELIV

A novel technique based upon injection‐charge extraction by linearly increasing voltage (i‐CELIV) in a metal‐insulator‐semiconductor (MIS) diode structure is described for studying charge transport in organic semiconductors. The technique (MIS‐CELIV) allows selective measurement of both electron and hole mobilities of organic solar cells with active layers thicknesses representative of operational devices. The method is used to study the model high efficiency bulk heterojunction combination poly[N‐9′′‐heptadecanyl‐2,7‐carbazole‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole)] (PCDTBT) and [6,6]‐phenyl C70‐butyric acid methyl ester (PC70BM) at various blend ratios. The absence of bipolar transport in PCDTBT‐and‐PC70BM‐only diodes is shown and strongly imbalanced carrier mobility is found in the most efficient “optimized” blend ratios. The mobility measurements are correlated with overall device performance and it is found that balanced and high charge carrier mobility are not necessarily required for high efficiencies in thin film organic solar cells.