共查询到20条相似文献,搜索用时 15 毫秒
1.
V. Pomero F. Lavaste G. Imbert W. Skalli 《Computer methods in biomechanics and biomedical engineering》2013,16(6):331-338
Evaluation of loads acting on the spine requires the knowledge of the muscular forces acting on it, but muscles redundancy necessitates developing a muscle forces attribution strategy. Optimisation, EMG, or hybrid models allow evaluating muscle force patterns, yielding a unique muscular arrangement or/and requiring EMG data collection. This paper presents a regulation model of the trunk muscles based on a proprioception hypothesis, which searches to avoid the spinal joint overloading. The model is also compared to other existing models for evaluation. Compared to an optimisation model, the proposed alternative muscle pattern yielded a significant spine postero-anterior shear decrease. Compared to a model based on combination of optimisation criteria, present model better fits muscle activation observed using EMG (38% improvement). Such results suggest that the proposed model, based on regulation of all spinal components, may be more relevant from a physiologic point of view. 相似文献
2.
The aim of the present study was to test the assumption that asymmetric trunk loading requires a higher total muscle force and consequently entails a higher compression forces on the spine as compared to symmetric loading. When the trunk musculature is modelled in sufficient detail, optimisation shows that there is no mechanical necessity for an increase in total muscle force (or compression force) with task asymmetry. A physiologically based optimisation does also not predict an increase in total muscle force or spinal loading with asymmetry. EMG data on 14 trunk muscles collected in eight subjects showed antagonistic coactivity to be present in both conditions. However, estimates of total muscle force based on the EMG were lower when producing an asymmetric moment. In conclusion, producing an asymmetric moment appears to cause slightly lower forces on the lumbosacral joint as compared to a symmetric moment. Only lateral shear forces increase with asymmetry but these remain well below failure levels. 相似文献
3.
Z. El Ouaaid N. Arjmand A. Plamondon 《Computer methods in biomechanics and biomedical engineering》2013,16(1):54-65
To circumvent the existing shortcoming of optimisation algorithms in trunk biomechanical models, both agonist and antagonist trunk muscle stresses to different powers are introduced in a novel objective function to evaluate the role of abdominal muscles in trunk stability and spine compression. This coupled objective function is introduced in our kinematics-driven finite element model to estimate muscle forces and to identify the role of abdominal muscles in upright standing while lifting symmetrically a weight at different heights. Predictive equations for the compression and buckling forces are developed. Results are also compared with the conventional objective function that neglects abdominal muscle forces. An overall optimal solution involving smaller spinal compression but higher trunk stability is automatically attained when choosing muscle stress powers at and around 3. Results highlight the internal oblique muscle as the most efficient abdominal muscle during the tasks investigated. The estimated relative forces in abdominal muscles are found to be in good agreement with the respective ratios of recorded electromyography activities. 相似文献
4.
Recently, experimental results have demonstrated that the load carrying capacity of the human spine substantially increases under the follower load condition. Thus, it is essential to prove that a follower load can be generated in vivo by activating the appropriate muscles in order to demonstrate the possibility that the stability of the spinal column could be maintained through a follower load mechanism. The aim of this study was to analyze the coordination of the trunk muscles in order to understand the role of the muscles in generating the follower load. A three-dimensional finite element model of the lumbar spine was developed from T12 to S1 and 117 pairs of trunk muscles (58 pairs of superficial muscles and 59 pairs of deep muscles) were considered. The follower load concept was mathematically represented as an optimization problem. The muscle forces required to generate the follower load were predicted by solving the optimization problem. The corresponding displacements and rotations at all nodes were estimated along with the follower forces, shear forces, and joint moments acting on those nodes. In addition, the muscle forces and the corresponding responses were investigated when the activations of the deep muscles or the superficial muscles were restricted to 75% of the maximum activation, respectively. Significantly larger numbers of deep muscles were involved in the generation of the follower load than the number of superficial muscles, regardless of the restriction on muscle activation. The shear force and the resultant joint moment are more influenced by the change in muscle activation in the superficial muscles. A larger number of deep trunk muscles were activated in order to maintain the spinal posture in the lumbar spine. In addition, the deep muscles have a larger capability to reduce the shear force and the resultant joint moment with respect to the perturbation of the external load or muscle fatigue compared to the superficial muscles. 相似文献
5.
Carlos Quental Jorge Ambrósio Jacinto Monteiro 《Computer methods in biomechanics and biomedical engineering》2013,16(7):749-759
The inverse dynamics technique applied to musculoskeletal models, and supported by optimisation techniques, is used extensively to estimate muscle and joint reaction forces. However, the solutions of the redundant muscle force sharing problem are sensitive to the detail and modelling assumptions of the models used. This study presents four alternative biomechanical models of the upper limb with different levels of discretisation of muscles by bundles and muscle paths, and their consequences on the estimation of the muscle and joint reaction forces. The muscle force sharing problem is solved for the motions of abduction and anterior flexion, acquired using video imaging, through the minimisation of an objective function describing muscle metabolic energy consumption. While looking for the optimal solution, not only the equations of motion are satisfied but also the stability of the glenohumeral and scapulothoracic joints is preserved. The results show that a lower level of muscle discretisation provides worse estimations regarding the muscle forces. Moreover, the poor discretisation of muscles relevant to the joint in analysis limits the applicability of the biomechanical model. In this study, the biomechanical model of the upper limb describing the infraspinatus by a single bundle could not solve the complete motion of anterior flexion. Despite the small differences in the magnitude of the forces predicted by the biomechanical models with more complex muscular systems, in general, there are no significant variations in the muscular activity of equivalent muscles. 相似文献
6.
The hypothesis that control of lumbar spinal muscle synergies is biomechanically optimized was studied by comparing EMG data with an analytical model with a multi-component cost function that could include (1) trunk displacements, (2) intervertebral displacements, (3) intervertebral forces; (4) sum of cubed muscle stresses, and (5) eigenvalues for the first two spinal buckling modes. The model's independent variables were 180 muscle forces. The 36 displacements of 6 vertebrae were calculated from muscle forces and the spinal stiffness. Calculated muscle activation was compared with EMG data from 14 healthy human subjects who performed isometric voluntary ramped maximum efforts at angles of 0 degrees, 45 degrees, 90 degrees, 135 degrees and 180 degrees to the right from the anterior direction. Muscle activation at each angle was quantified as the linear regression slope of the RMS EMG versus external force relationship, normalized by the maximum observed EMG.There was good agreement between the analytical model and EMG data for the dorsal muscles when the model included either minimization of intervertebral displacements or minimization of intervertebral forces in its cost function, but the model did not predict a realistic level of abdominal muscles activation. Agreement with EMG data was improved with the sum of the cubed muscle stresses added to the cost function. Addition of a cost function component to maximize the trunk stability produced higher levels of antagonistic muscle activation at low efforts than at greater efforts. It was concluded that the muscle activation strategy efficiently limits intervertebral forces and displacements, and that costs of higher muscle stresses are taken into account, but stability does not appear to be maximized. Trunk muscles are apparently not controlled solely to optimize any one of the biomechanical costs considered here. 相似文献
7.
Direct quantitative measurement of muscle forces is not possible. Forces in the trunk muscles were estimated for standing and flexion of the upper body using three-dimensional, nonlinear finite element models of the lumbar spine with and without an internal spinal fixation device. Muscle forces assumed were two pairs dorsally and one ventrally, each representing several muscles. Muscle forces in the model with internal fixators were varied in discrete steps until the implant loads calculated closely corresponded to those measured in a patient with an instrumented implant. The calculated angles between adjacent lumbar vertebrae were compared with corresponding values measured on X-ray films of a patient as well as with literature values and served as a second criterion for predicting muscle forces. For the model without an implant, the muscle forces of the first model were slightly varied until the lumbar spine shape and the intradiscal pressure were physiological. The abdomen was shown to have a considerable supporting function for flexion. 相似文献
8.
In biomechanics, musculoskeletal models are typically redundant. This situation is referred to as the distribution problem. Often, static, non-linear optimisation methods of the form “min: φ(f) subject to mechanical and muscular constraints” have been used to extract a unique set of muscle forces. Here, we present a method for validating this class of non-linear optimisation approaches where the homogeneous cost function, φ(f), is used to solve the distribution problem. We show that the predicted muscle forces for different loading conditions are scaled versions of each other if the joint loading conditions are just scaled versions. Therefore, we can calculate the theoretical muscle forces for different experimental conditions based on the measured muscle forces and joint loadings taken from one experimental condition and assuming that all input into the optimisation (e.g., moment arms, muscle attachment sites, size, fibre type distribution) and the optimisation approach are perfectly correct. Thus predictions of muscle force for other experimental conditions are accurate if the optimisation approach is appropriate, independent of the musculoskeletal geometry and other input required for the optimisation procedure. By comparing the muscle forces predicted in this way to the actual muscle forces obtained experimentally, we conclude that convex homogeneous non-linear optimisation approaches cannot predict individual muscle forces properly, as force-sharing among synergistic muscles obtained experimentally are not just scaled versions of joint loading, not even in a first approximation. 相似文献
9.
Christoph Engelhardt Valérie Malfroy Camine David Ingram Philippe Müllhaupt Alain Farron Dominique Pioletti 《Computer methods in biomechanics and biomedical engineering》2013,16(12):1272-1279
The estimation of muscle forces in musculoskeletal shoulder models is still controversial. Two different methods are widely used to solve the indeterminacy of the system: electromyography (EMG)-based methods and stress-based methods. The goal of this work was to evaluate the influence of these two methods on the prediction of muscle forces, glenohumeral load and joint stability after total shoulder arthroplasty. An EMG-based and a stress-based method were implemented into the same musculoskeletal shoulder model. The model replicated the glenohumeral joint after total shoulder arthroplasty. It contained the scapula, the humerus, the joint prosthesis, the rotator cuff muscles supraspinatus, subscapularis and infraspinatus and the middle, anterior and posterior deltoid muscles. A movement of abduction was simulated in the plane of the scapula. The EMG-based method replicated muscular activity of experimentally measured EMG. The stress-based method minimised a cost function based on muscle stresses. We compared muscle forces, joint reaction force, articular contact pressure and translation of the humeral head. The stress-based method predicted a lower force of the rotator cuff muscles. This was partly counter-balanced by a higher force of the middle part of the deltoid muscle. As a consequence, the stress-based method predicted a lower joint load (16% reduced) and a higher superior–inferior translation of the humeral head (increased by 1.2 mm). The EMG-based method has the advantage of replicating the observed cocontraction of stabilising muscles of the rotator cuff. This method is, however, limited to available EMG measurements. The stress-based method has thus an advantage of flexibility, but may overestimate glenohumeral subluxation. 相似文献
10.
A major limitation of optimization models of the spine has been the inability to accurately predict trunk muscle co-activity. Antagonist muscle activity is thought to be necessary to maintain adequate levels of spine stability but, in turn, creates increased loading on the spine. It is thus hypothesized that the CNS attempts to optimize the relationship between spine loading and spine stability in determining muscular activation patterns. This study presents an optimization model of the spine in which stability was constrained to target levels predicted from regression equations of independent loading variables. Objective functions were set to either minimize the sum of the cubed muscle forces or minimize the sum of the squared intervertebral forces at the L4-L5 disc level. Results demonstrate that the inclusion of stability constraints in optimization simulations produced realistic predictions of antagonist muscle activity and predictions of spine compression levels that agree more closely with EMG-based estimates, compared to simulations in which stability was unconstrained. It was concluded that spinal stability is a vital consideration for the CNS when dictating trunk muscle recruitment patterns. 相似文献
11.
Reliable computation of spinal loads and trunk stability under whole body vibrations with high acceleration contents requires accurate estimation of trunk muscle activities that are often overlooked in existing biodynamic models. A finite element model of the spine that accounts for nonlinear load- and direction-dependent properties of lumbar segments, complex geometry and musculature of the spine, and dynamic characteristics of the trunk was used in our iterative kinematics-driven approach to predict trunk biodynamics in measured vehicle's seat vibrations with shock contents of about 4g (g: gravity acceleration of 9.8m/s(2)) at frequencies of about 4 and 20Hz. Muscle forces, spinal loads and trunk stability were evaluated for two lumbar postures (erect and flexed) with and without coactivity in abdominal muscles. Estimated peak spinal loads were substantially larger under 4Hz excitation frequency as compared to 20Hz with the contribution of muscle forces exceeding that of inertial forces. Flattening of the lumbar lordosis from an erect to a flexed posture and antagonistic coactivity in abdominal muscles, both noticeably increased forces on the spine while substantially improving trunk stability. Our predictions clearly demonstrated the significant role of muscles in trunk biodynamics and associated risk of back injuries. High-magnitude accelerations in seat vibration, especially at near-resonant frequency, expose the vertebral column to large forces and high risk of injury by significantly increasing muscle activities in response to equilibrium and stability demands. 相似文献
12.
Bazrgari B Shirazi-Adl A 《Computer methods in biomechanics and biomedical engineering》2007,10(5):351-360
The spinal stability and passive-active load partitioning under dynamic squat and stoop lifts were investigated as the ligamentous stiffness in flexion was altered. Measured in vivo kinematics of subjects lifting 180 N at either squat or stoop technique was prescribed in a nonlinear transient finite element model of the spine. The Kinematics-driven approach was utilized for temporal estimation of muscle forces, internal spinal loads and system stability. The finite element model accounted for nonlinear properties of the ligamentous spine, wrapping of thoracic extensor muscles and trunk dynamic characteristics while subject to measured kinematics and gravity/external loads. Alterations in passive properties of spine substantially influenced muscle forces, spinal loads and system stability in both lifting techniques, though more so in stoop than in squat. The squat technique is advocated for resulting in smaller spinal loads. Stability of spine in the sagittal plane substantially improved with greater passive properties, trunk flexion and load. Simulation of global extensor muscles with curved rather than straight courses considerably diminished loads on spine and increased stability throughout the task. 相似文献
13.
Michala Cadova Miloslav Vilimek Matej Daniel 《Computer methods in biomechanics and biomedical engineering》2014,17(4):311-317
Determination of muscle forces in individual muscles is often essential to assess optimal performance of human motion. Inverse dynamic methods based on the kinematics of the given motion and on the use of optimisation approach are the most widely used for muscle force estimation. The aim of this study was to estimate how the choice of muscle model influences predicted muscle forces. Huxley's (1957, Prog Biophys Biop Chem. 7: 255–318) and Hill's (1938, Proc R Soc B. 126: 136–195) muscle models were used for determination of muscle forces of two antagonistic muscles of the lower extremity during cycling. Huxley's model is a complex model that couples biochemical and physical processes with the microstructure of the muscle whereas the Hill's model is a phenomenological model. Muscle forces predicted by both models are within the same range. Huxley's model predicts more realistic patterns of muscle activation but it is computationally more demanding. Therefore, if the overall muscle forces are to be assessed, it is reasonable to use a simpler implementation based on Hill's model. 相似文献
14.
Relative efficiency of abdominal muscles in spine stability 总被引:1,自引:0,他引:1
Arjmand N Shirazi-Adl A Parnianpour M 《Computer methods in biomechanics and biomedical engineering》2008,11(3):291-299
Using an iterative kinematics-driven nonlinear finite element model, relative efficiency of individual abdominal muscles in spinal stability in upright standing posture was investigated. Effect of load height on stability and muscle activities was also computed under different coactivity levels in abdominal muscles. The internal oblique was the most efficient muscle (compared with the external oblique and rectus abdominus) in providing stability while generating smaller spinal loads with lower fatigue rate of muscles. As the weight was held higher, stability deteriorated requiring additional flexor-extensor activities. The stabilising efficacy of abdominal muscles diminished at higher activities. The difference in critical loads in frontal and sagittal planes computed in the absence of abdominal coactivity disappeared under prescribed coactivities suggesting an optimal system in stability. The central nervous system may settle for a less stable spine in favour of lowering the risk of injury. Findings could help introduce stability criterion in optimisation models. 相似文献
15.
A wide range of loading conditions involving external forces with varying magnitudes, orientations and locations are encountered in daily activities. Here we computed the effect on trunk biomechanics of changes in force location (two levels) and orientation (5 values) in 4 subjects in upright standing while maintaining identical external moment of 15 Nm, 30 N m or 45 Nm at the L5–S1. Driven by measured kinematics and gravity/external loads, the finite element models yielded substantially different trunk neuromuscular response with moderate alterations (up to 24% under 45 Nm moment) in spinal loads as the load orientation varied. Under identical moments, compression and shear forces at the L5–S1 as well as forces in extensor thoracic muscles progressively decreased as orientation of external forces varied from downward gravity (90°) all the way to upward (−25°) orientation. In contrast, forces in local lumbar muscles followed reverse trends. Under larger horizontal forces at a lower elevation, lumbar muscles were much more active whereas extensor thoracic muscle forces were greater under smaller forces at a higher elevation. Despite such differences in activity pattern, the spinal forces remained nearly identical (<6% under 45 Nm moment). The published recorded surface EMG data of extensor muscles trend-wise agreed with computed local muscle forces as horizontal load elevation varied but were overall different from results in both local and global muscles when load orientation altered. Predictions demonstrate the marked effect of external force orientation and elevation on the trunk neuromuscular response and spinal forces and questions attempts to estimate spinal loads based only on consideration of moments at a spinal level. 相似文献
16.
17.
Previous in-vivo studies suggest that the ratio of total lumbar rotation over pelvic rotation (lumbo-pelvic rhythm) during trunk sagittal movement is essential to evaluate spinal loads and discriminate between low back pain and asymptomatic population. Similarly, there is also evidence that the lumbo-pelvic rhythm is key for evaluation of realistic muscle and joint reaction forces and moments predicted by various computational musculoskeletal models. This study investigated the effects of three lumbo-pelvic rhythms defined based on in-vivo measurements on the spinal response during moderate forward flexion (60°) using a combined approach of musculoskeletal modeling of the upper body and finite element model of the lumbosacral spine. The muscle forces and joint loads predicted by the musculoskeletal model, together with the gravitational forces, were applied to the finite element model to compute the disc force and moment, intradiscal pressure, annular fibers strain, and load-sharing. The results revealed that a rhythm with high pelvic rotation and low lumbar flexion involves more global muscles and increases the role of the disc in resisting spinal loads, while its counterpart, with low pelvic rotation, recruits more local muscles and engages the ligaments to lower the disc loads. On the other hand, a normal rhythm that has balanced pelvic and lumbar rotations yields almost equal disc and ligament load-sharing and results in more balanced synergy between global and local muscles. The lumbo-pelvic rhythm has less effect on the intradiscal pressure and annular fibers strain. This work demonstrated that the spinal response during forward flexion is highly dependent on the lumbo-pelvic rhythm. It is therefore, essential to adapt this parameter instead of using the default values in musculoskeletal models for accurate prediction of muscle forces and joint reaction forces and moments. The findings provided by this work are expected to improve knowledge of spinal response during forward flexion, and are clinically relevant towards low back pain treatment and disc injury prevention. 相似文献
18.
N. Arjmand D. Gagnon A. Plamondon A. Shirazi-Adl C. Larivière 《Journal of biomechanics》2010,43(3):485-491
Despite recent advances in modeling of the human spine, simplifying assumptions are still required to tackle complexities. Such assumptions need to be scrutinized to assess their likely impacts on predictions. A comprehensive comparison of muscle forces and spinal loads estimated by a single-joint (L5–S1) optimisation-assisted EMG-driven (EMGAO) and a multi-joint Kinematics-driven (KD) model of the spine under symmetric (symmetric trunk flexion from neutral upright to maximum forward flexion) and asymmetric (holding a load at various heights in the right hand) activities is carried out. Regardless of the task simulated, the KD model predicted greater activities in extensor muscles as compared to the EMGAO model. Such differences in the symmetric tasks was due mainly to the distinct approaches to resolve the redundancy while in the asymmetric tasks they were due also to the different methods used to estimate joint moments. Shear and compression forces were generally higher in the KD model. Differences in predictions between these modeling approaches varied depending on the task simulated and the joint considered in the single-joint EMGAO model. The EMGAO model should incorporate a multi-joint strategy to satisfy equilibrium at different levels while the KD model should benefit from recorded EMG activities of the antagonistic muscles to supplement input measured kinematics. 相似文献
19.
Musculoskeletal models generally solve the muscular redundancy by numerical optimisation. They have been extensively validated using instrumented implants. Conversely, a reduction approach considers only one flexor or extensor muscle group at the time to equilibrate the inter-segmental joint moment. It is not clear if such models can still predict reliable joint contact and musculo-tendon forces during gait.Tibiofemoral contact force and gastrocnemii, quadriceps, and hamstrings musculo-tendon forces were estimated using a reduction approach for five subjects walking with an instrumented prosthesis. The errors in the proximal-distal tibiofemoral contact force fell in the range (0.3–0.9 body weight) reported in the literature for musculoskeletal models using numerical optimisation. The musculo-tendon forces were in agreement with the EMG envelops and appeared comparable to the ones reported in the literature with generic musculoskeletal models.Although evident simplifications and limitations, it seems that the reduction approach can provided quite reliable results. It can be a useful pedagogical tool in biomechanics, e.g. to illustrate the theoretical differences between inter-segmental and contact forces, and can provide a first estimate of the joint loadings in subjects with limited musculoskeletal deformities and neurological disorders. 相似文献
20.
Determination of the trunk maximum voluntary exertion moment capacity and associated internal spinal forces could serve in proper selection of workers for specific occupational task requirements, injury prevention and treatment outcome evaluations. Maximum isometric trunk exertion moments in flexion and extension along with surface EMG of select trunk muscles are measured in 12 asymptomatic subjects. Subsequently and under individualized measured harness-subject forces, kinematics and upper trunk gravity, an iterative kinematics-driven finite element model is used to compute muscle forces and spinal loads in 4 of these subjects. Different co-activity and intra-abdominal pressure levels are simulated. Results indicate significantly larger maximal resistant moments and spinal compression/shear forces in extension exertions than flexion exertions. The agonist trunk muscles reach their maximum force generation (saturation) to greater extent in extension exertions compared to flexion exertions. Local lumbar extensor muscles are highly active in extension exertions and generate most of the internal spinal forces. The maximum exertion attempts produce large spinal compression and shear loads that increase with the antagonist co-activity level but decrease with the intra-abdominal pressure. Intra-abdominal pressure decreases agonist muscle forces in extension exertions but generally increase them in flexion exertions. 相似文献