Biological indicators for low temperature steam and formaldehyde sterilization: the effect of defined media on sporulation, growth index and formaldehyde resistance of spores of Bacillus stearothermophilus strains

Preliminary screening was carried out on spores of 29 strains of Bacillus stearothermophilus to determine their potential as biological indicator organisms for low temperature steam and formaldehyde sterilization. Each strain was sporulated on four chemically defined media. Fourteen strains produced satisfactory sporulation on one or more of the media but there was considerable variation in the extent of sporulation. The growth index of the spores, which was dependent on both the strain of organism and the sporulation medium, ranged from 1% to 90%. The spores were appraised on the basis of their resistance to inactivation by 0.5% w/v formaldehyde in aqueous solution at 70°C. The survivor curves obtained could be characterized into five types on the basis of the shape of the curve. Only five strains of Bacillus stearothermophilus produced spores with the characteristics of high resistance, linear semi-logarithmic survivor curve and high growth index that would be required of a potential biological indicator organism.     

Biological indicators for low temperature steam and formaldehyde sterilization: effect of variations in recovery conditions on the response of spores of Bacillus stearothermophilus NCIMB 8224 to low temperature steam and formaldehyde

Spores of a Bacillus stearothermophilus strain thought to be a good biological monitor for low temperature steam and formaldehyde (LTSF) sterilization have been subjected to different recovery environments following exposure to relevant LTSF treatments and prior to enumerating the numbers of surviving spores. The recovery treatments essentially consisted of holding samples at a temperature of 90°C for different time periods prior to plating out following exposure to 12 μg ml^-1 formaldehyde at temperatures between 63° and 83°C The data indicate that LTSF-exposed spores show a marked recovery when kept at 90°C prior to plating out; the extent of the recovery increases with increasing inactivation temperature between 73° and 83°C. The data bring into question the sporicidal activity of LTSF.     

Implications of paper vs stainless steel biological indicator substrates for formaldehyde gas decontamination

Aims: This study was undertaken to determine the effectiveness of biological indicators currently being employed during formaldehyde decontamination. Data suggest that detectable amounts of formaldehyde are absorbed into the paper strips contained in currently used biological indicators. Absorbed formaldehyde has the potential to inhibit the growth of indicator spores, thus leading to false negative results. Indicators composed of either stainless steel carriers or paper strips were investigated to determine whether stainless steel carriers can be used as an alternative to paper strip indicators. Methods and Results: Biological indicators were exposed to formaldehyde gas and were tested for the presence of formaldehyde and any possible inhibition of spore growth. Absorbed formaldehyde was detected in the paper strip carriers while no formaldehyde was detected from any of the stainless steel carriers. Exposed paper strips were found to inhibit growth of up to 1 × 10⁶ spores while the stainless steel carriers did not inhibit the growth of spores. Conclusions: During decontamination, biological indicators composed of paper spore strips absorb formaldehyde and inhibit growth of any surviving spores. Stainless steel carriers do not absorb formaldehyde and are an ideal alternative substrate for biological indicators. Significance and Impact of the Study: The popular paper strip biological indicator can lead to false negative results during decontamination and is unsuitable for validating formaldehyde decontamination.     

Potential biological indicators for glutaraldehyde and formaldehyde sterilization processes

The present study aimed to isolate, select, and evaluate bacterial isolates with potential for use as biological indicators for sterilization with glutaraldehyde and/or formaldehyde. A total of 340 local Bacillus isolates were screened for glutaraldehyde and/or formaldehyde resistance by determination of minimum inhibitory concentrations (MICs), minimum bactericidal concentrations (MBCs), and extinction time and were compared with B. subtilis (var. niger) ATCC 9372, the biological indicator for ethylene oxide sterilization, as reference. Of these, 85 isolates had glutaraldehyde MICs of 0.5% or higher, while 29 had formaldehyde MICs of 0.04% or higher. Of the 29 resistant isolates, 15 had MBCs of 0.05% or more. Extinction times were used to evaluate the bactericidal/sporicidal activity of glutaraldehyde. Eight had inactivation times of more than 5 h in 2% glutaraldehyde (pH 8), whereas 12 had inactivation times of more than 3 h in l% formaldehyde, with one isolate in common. These 19 isolates were selected and evaluated as potential biological indicators for aldehydes by determination of the decimal reduction times (D values), compared with the reference strain. Eight glutaraldehyde-resistant isolates exhibited D values 2.0- to 3.5-fold higher than the reference strain (30 min.). Only five of 12 formaldehyde resistant isolates had D values higher than that of the reference strain. Using six resistant isolates, temperature coefficient values between 2.11 and 3.02 were obtained for 2% formaldehyde. Finally, 14 isolates were tested for potential pathogenicity and were identified to species level. All of the eight glutaraldehyde-resistant isolates, including the isolate with dual resistance, and three formaldehyde-resistant isolates were B. licheniformis, while two other formaldehyde-resistant isolates were B. cereus. Six of the selected B. licheniformis isolates are potential biological indicators for sterilization processes using aldehydes. Three can be suggested for glutaraldehyde only and three for both aldehydes. Electronic Publication     

Dihydroxyacetone detoxification in Saccharomyces cerevisiae involves formaldehyde dissimilation

To investigate Saccharomyces cerevisiae physiology during growth on the conditionally toxic triose dihydroxyacetone (DHA), protein expression was studied in strains overexpressing either of the two dihydroxyacetone kinase isogenes, DAK1 or DAK2, that grow well utilizing DHA as a carbon and energy source. DHA metabolism was found mostly similar to ethanol utilization, involving a strong component of glucose derepression, but also involved DHA-specific regulatory changes. A specific and strong (10- to 30-fold induction of formaldehyde dehydrogenase, Fdhlp, indicated activation of the formaldehyde dissimilation pathway in DHA medium. The importance of this pathway was further supported by impaired adaptation to DHA growth and DHA survival in a glutathione-dependent formaldehyde dehydrogenase (SFA1) deletion mutant. Glutathione synthase (GSH1) deletion led to decreased DHA survival in agreement with the glutathione cofactor requirement for the SFA1-encoded activity. DHA toxicity did, however, not solely appear related to formaldehyde accumulation, because SFA1 overexpression only enhanced formaldehyde but not DHA tolerance. In further agreement with a low DHA-to-formaldehyde flux, GSH supplements in the low microM range also fully suppressed the DHA sensitivity of a gsh1Delta strain. Under growth reduction on high (100 mM) DHA medium we report increased levels of advanced glycation end-product (AGE) formation on total protein. Under these high-DHA conditions expression of several stress-related proteins, e.g. a heat-shock protein (Hsp104p) and the oxidative stress indicator, alkyl hydroperoxide reductase (Ahp1p) was also found induced. However, hallmark determinants of oxidative stress tolerance (e.g. YAP1, SKN7, HYR1/GPX3 and SOD2) were redundant for DHA tolerance, thus indicating mechanisms of DHA toxicity largely independent of central oxidative stress defence mechanisms. We conclude that mechanisms for DHA growth and detoxification appear complex and that the evolutionary strive to minimize detrimental effects of this intracellular metabolite links to both formaldehyde and glutathione metabolism.     

高效降解甲醛菌株的分离鉴定及其特性

首先对新分离的、能高效降解甲醛的两菌株A1和A2在形态学特征、生理生化特性及16S rDNA序列分析等方面进行了系统研究; 随后通过测定在液体培养过程中甲醛浓度的变化, 确定新分离菌株A1、A2降解溶液中甲醛的性能; 最后利用菌株A1、A2分别进行生物填料塔的挂膜实验, 确定其对甲醛气体的净化性能。结果表明: 菌株A1属于假单胞菌属(Pseudomonas), 菌株A2为鞘氨醇单胞菌属(Sphingomonas); 当甲醛初始浓度<1 200 mg/L时,菌株A1、A2都能完全降解溶液中的甲醛, 当甲醛浓度增高至1 600 mg/L时, 菌株A1在48 h后的甲醛降解率为50%, 菌株A2在104 h后的甲醛降解率为74.3%; 菌株A1、A2对甲醛气体的净化效率均能达到99%以上, 菌株A1的甲醛生化去除量能达到26.4 mg/(L?h), 菌株A2的甲醛生化去除量可达20.6 mg/(L?h)。     

Biological indicators for low temperature steam formaldehyde sterilization: effect of defined media on sporulation, germination index and moist heat resistance at 110dEC of Bacillus strains

Choice of a biological indicator depends upon selecting a strain with the optimum balance of desirable properties. Screening 20 strains of Bacillus spp. for sporulation on three defined media has shown the wide variation that occurs in requirements for sporulation and properties of the resultant spores. Comparison of germination index and moist heat resistance of resultant spores suggest that a combination of high germination index, high heat resistance and linear inactivation may not be possible.     

Biological indicators for low temperature steam formaldehyde sterilization: effect of defined media on sporulation, germination index and moist heat resistance at 110 degrees C of Bacillus strains

Choice of a biological indicator depends upon selecting a strain with the optimum balance of desirable properties. Screening 20 strains of Bacillus spp. for sporulation on three defined media has shown the wide variation that occurs in requirements for sporulation and properties of the resultant spores. Comparison of germination index and moist heat resistance of resultant spores suggest that a combination of high germination index, high heat resistance and linear inactivation may not be possible.     

Monitoring the efficacy of steam and formaldehyde treatment of naturally Salmonella-infected layer houses

AIMS: To monitor if a temperature-humidity-time treatment found to be effective in eliminating Salmonella in laboratory trials (Gradel et al. 2003) was efficient against Salmonella in naturally infected layer houses. METHODS AND RESULTS: Six layer houses with natural Salmonella infections were steam treated in a download period, aiming at >or=60 degrees C and 100% relative humidity (RH) during a 24-h period, with or without the addition of 30 ppm formaldehyde. In addition, two control layer houses were disinfected chemically. Salmonella samples taken from predetermined sites before and after treatment were tested qualitatively for Salmonella and coliforms. Samples with indicator bacteria (feed inoculated with Escherichia coli or Enterococcus faecalis and faeces with naturally occurring E. coli and enterococci) were placed during steam-treatment at 12 sites in each house (where the temperature was logged at 5-min intervals) and tested for surviving bacteria. Generally, the field test results confirmed the results of laboratory tests, especially when 30 ppm formaldehyde was added to the steam. In well-sealed houses, the recommended temperature-humidity-time scheme was accomplished at a minimum of 10 cm above floor level within 1 h. CONCLUSIONS: A steam treatment of >or=60 degrees C and 100% RH during a 24-h period with the addition of 30 ppm formaldehyde at the beginning of the process is recommended for eliminating Salmonella from naturally infected poultry layer houses. SIGNIFICANCE AND IMPACT OF THE STUDY: A specific recommendation for the elimination of Salmonella in poultry houses can be given.     

Mutagenic characteristics of formaldehyde on bacterial systems

The mutagenic characteristics of formaldehyde on bacteria were examined. All the tester strains of Escherichia coli deficient in DNA-repair enzymes tested in the present study were significantly more sensitive to the killing effect of formaldehyde than the corresponding wild-type strain. Among the E. coli B strains, H/r30R (wild-type) and Hs30R (uvrA) were mutable, whereas NG30 (recA) and O16 (polA) were not. There is no appreciable difference in mutation frequency of E. coli B between the wild-type and the uvrA strains in a dose range below 4 mM. However, the mutation frequency of the wild-type strain started to decrease in a higher concentration range, whereas that of the uvrA strain continued to increase linearly. This was confirmed with the E. coli B/r tester strains. The decrease in mutation frequency may be produced by prolongation of the lag period before entering the S-phase so as to give the cells a greater chance for DNA repair through the excision mechanism. In fact, it was evidenced that formaldehyde retarded to a remarkable extent the initiation of DNA synthesis of the cells at the higher dose range used for mutation assay. Some discrepancies found between the results obtained in this study and those previously reported by Nishioka (1973) were pointed out.     

一株甲醛降解菌的筛选及降解特性的研究

【目的】以甲醛为唯一碳源与能源,以期从印染厂采集的活性污泥中筛选出快速降解甲醛的菌株。【方法】采用传统微生物纯培养方法和形态学特征、生理生化试验,结合16S rRNA基因序列分析以及甲醛关键脱氢酶(FDH)对筛选的菌株W1进行系统研究,并利用正交设计法研究不同因素处理对菌株W1降解甲醛特性的影响。【结果】分类结果显示鉴定菌株W1属于恶臭假单胞菌(Pseudomonas putida),通过单因素试验和正交试验考察培养条件对菌株降解甲醛的影响,得出菌株W1降解甲醛的最适条件为:甲醛浓度为500 mg/L,温度30°C,pH 6.0,摇床转速为200 r/min,接种量为3%。【结论】在最适条件下菌株W1具有较强的降解甲醛能力,在24 h其甲醛降解率达98%。     

Utilization of methanol by rhodospirillaceae

Enrichment culture of organisms growing anaerobically in the light in methanol-bicarbonate medium resulted in isolation of strains of Rhodopseudomonas gelatinosa and Rhodopseudomonas acidophila. The pH optimum for growth on methanol for all strains tested was approximately one unit higher than for growth on carbon sources containing more than one carbon atom. At the appropriate pH, 17 strains of Rhodospirillaceae out of 39 in a culture collection grew anaerobically in the light on methanol-bicarbonate. Rhodopseudomonas acidophila strain 10050 showed the most abundant growth and was studied in more detail. Its growth on methanol was stimulated by yeast extract or vitamin-free casamino acids. The organism grew on methanol-bicarbonate, methanol-formate or formate alone as the sole carbon sources. No growth was observed on methylamine or formaldehyde. In the presence of excess bicarbonate a maximum yield of 98 g cell material from 100 g methanol was obtained. Ribulose diphosphate carboxylase was present in the methanol-bicarbonate-grown organism at six times the specific activity of that in the succinate-grown organism.     

温度对抗性朱砂叶螨发育和繁殖的影响

比较了朱砂叶螨Tetranychus cinnabarinus (Boiduval)敏感品系（S）、阿维菌素抗性品系（AR）和甲氰菊酯抗性品系（FR）在不同温度下的发育和繁殖情况,用王-兰-丁模型拟合了各品系发育速率与温度的关系。结果表明,在36℃下,S品系和FR品系卵均不能孵化,而AR品系却能完成世代发育。15℃下,AR和FR品系的世代历期分别比S品系延长8.0和6.2天,产卵前期均比S品系缩短约2.0天。在20～28℃下,S品系繁殖力大于抗性品系; 在34℃下, AR品系的产卵量显著大于S和FR品系。S、FR和AR品系发育临界高温分别为36.0℃、36.1℃和42.4℃。结果提示AR品系对高温的适应能力较S和FR品系明显增强。     

Resistance of Mycobacterium chelonei-like organisms to formaldehyde.

Mycobacterium chelonei-like organisms have been isolated from patients in two outbreaks of peritonitis involving chronic peritoneal dialysis machines routinely disinfected with 2 to 3% formaldehyde. Susceptibility studies revealed that water-adapted M. chelonei-like organism strains could survive 2 h of exposure to 10% formaldehyde.     

一株具有拮抗作用的解淀粉芽孢杆菌的筛选、鉴定及生物学特性研究

本研究以樱桃番茄成熟红果为样本,以极细链格孢菌为指示菌筛选得到一株对番茄采后病原菌有抑制作用的菌株KL-1。通过平板拮抗试验研究了菌株KL-1对番茄采后常见病原真菌极细链格孢菌、黑曲霉、青霉菌、尖侧多隔孢霉、拟康宁木霉、盐生枝孢霉、子囊菌、胶孢炭疽菌等八种病原菌的抑制作用,同时通过形态学、生理生化及16S rDNA分子生物学特征对菌株进行了鉴定,并对其基本生物学特性进行了研究。结果表明:菌株KL-1对于七种病原菌极细链格孢菌、黑曲霉、青霉菌、拟康宁木霉、盐生枝孢霉、子囊菌和胶孢炭疽菌均有明显的抑制作用,其中对黑曲霉的抑制率最大为81%,对其他六种病原菌抑制率也均高于70%,对尖侧多隔孢霉的抑制率为0,说明菌株KL-1可以抑制番茄多种常见病原真菌,具有开发为生防制剂的潜力。经鉴定KL-1为解淀粉芽孢杆菌(Bacillus amyloliquefaciens);该菌培养9 h内生长最旺盛,最适生长pH为7.0,最适生长温度为37℃。     

Effects of growth temperature and pVM82 plasmid on fatty acids of lipid A from Yersinia pseudotuberculosis

Effects of cultivation temperature (8 or 37 degrees C) and plasmid profile on the lipid A fatty acids of three isogenic Yersinia pseudotuberculosis strains (plasmidless (82-) and strains containing pVM82 (82+) or p57 (57+) plasmids) obtained by alkaline hydrolysis of the whole bacterial cells and differentiated from fatty acids of other membrane lipids were investigated. On the basis of the analysis, it is concluded that lipids A of all studied samples contain 3-hydroxytetradecanoic and dodecanoic acids, a part of which exists as the 3-dodecanoyloxytetradecanoic derivative. The effect of temperature appears in the higher contents of ester- and amide-linked 3-acyloxyalkanoic residues in lipid A from the "cold" variants of the bacteria and is determined by chromosomal genes. The plasmid effect is seen as various responses of the isogenic derivatives to change of growth temperature: in cells of strains 82+ and 82- grown in the cold, the share of lipid A fatty acids in the total population of cellular fatty acids is reduced, while in strains with plasmid p57 it is increased. The temperature variants of the 57+ strain differ by the low contents of amide-linked 3-acyloxyalkanoic acids. Finally, lack of plasmid pVM82 in the "warm" variants of the bacteria results in accumulation of glycolipid molecules deprived of dodecanoic acid. Correlation between growth temperature and plasmid profiles, on one hand, and lipid A fatty acid composition and potential pathogenic properties of the Y. pseudotuberculosis, on the other hand, and also possible mechanisms of thermal adaptation of this organism are discussed.     

The reduction of formaldehyde by bacterial cells

Formaldehyde is reduced to methyl alcohol by living cells of a creatinine-decomposing strain of Pseudomonas aeruginosa. The amount of HCHO taken up in 30 minutes by 3 x 10(10) cells of this organism is termed its reducing capacity. It was found to be 400 to 480 microg. The reaction takes place over wide pH and temperature ranges, is independent of the concentration of formaldehyde as long as the latter is not high enough to exert a toxic effect on the cell, but depends on the number of bacteria present. In cultures, 3 to 7 days old, there is a decline in reducing capacity without a proportionate decrease in the number of viable cells. On the other hand in cultures, 2 to 4 weeks old, the number of viable cells determines the amount of HCHO taken up. N/100 NaOH depresses the reducing capacity of the organism without affecting bacterial viability. Exposure of bacterial suspensions to temperatures of 46-52 degrees C. for 10 minutes causes a far more rapid decrease in the number of viable cells than in reducing capacity. Incubation of cellular suspensions with nutrient substances, which are able to support adequately the growth of the organism, for 30 minutes prior to the addition of HCHO, induces increases in reducing capacity. The uptake of HCHO by different microorganisms seems to be related to their gaseous and nutritional requirements. Strains of P. aeruginosa and P. fluorescens are predominantly aerobic, least fastidious in their nutritional requirements, most active against HCHO, and least susceptible to the action of aureomycin and chloromycetin. The potential significance of cellular reducing capacity is discussed.     

Combined effects of sulfites, temperature, and agitation time on production of glycerol in grape juice by Saccharomyces cerevisiae.

Analysis of variance was used to evaluate the simultaneous effects of strain, incubation temperature (15 to 25 degrees C), agitation time (0 to 24 h), and initial sulfite concentration (100 to 300 ppm) on glycerol production in grape juice by Saccharomyces cerevisiae. Fourteen strains were studied to determine their growth patterns in the presence of sulfites and ethanol. Baker's yeast strains were more sensitive to sulfite than wine strains, and little growth occurred at initial sulfite levels greater than 150 ppm. Sensitivity to sulfite increased with increasing levels of ethanol. Three strains exhibiting the best growth in the presence of sulfites and ethanol were selected for interaction studies. Fermentations were carried out until the solids content had decreased to less than 6 degrees Brix, which was the point that glycerol content became stable. For the three strains used, the greatest level of glycerol production was observed in the presence of 300 ppm of sulfite for most incubation temperatures and agitation times. There was significant interaction between the strain, incubation temperature, and agitation time parameters for glycerol synthesis, and a response surface method was used to predict the optimal conditions for glycerol production. Under static conditions, the highest level of glycerol production was observed at 20 degrees C, while incubation at 25 degrees C gave the best results when the cultures were agitated for 24 h. Response surface equations were used to predict that the optimum conditions for glycerol production by S. cerevisiae Y11 were a temperature of 22 degrees C, an initial sulfite concentration of 300 ppm, and no agitation, which yielded 0.68 g of glycerol per 100 ml.     

The effect of incubation temperature and sodium chloride concentration on the growth kinetics of Vibrio anguillarum and Vibrio anguillarum-related organisms

The effect of temperature and NaCl concentration on the growth kinetics of Vibrio anguillarum and V. anguillarum -related (VAR) strains was studied.
For one wild VAR strain, NaCl concentration interfered with growth temperature parameters, in particular, with the maximum growth temperature but also with the optimum temperature (defined as the temperature at which μ_max equals its maximal value μ_opt), and with μ_opt itself. For the same strain, optimal growth required the adding of NaCl to the medium to a final concentration of 1·5%. These results were not confirmed by tests on a V. anguillarum collection strain.
When the NaCl concentration in the culture media was 1.5%, the optmum temperature for the nine strains studied ranged from 29.7°C to 34°C whereas the maximum temperature ranged between 35.3°C and 38.5°C.
Hence, antbiotic susceptibility testing as well as biochemical identification might be carried out at 30°C in the presence of 1.5% NaCl, which corresponded to a suboptimal growth.