Measurement of joint capsule tissue loading in the cat knee using calibrated mechanoreceptors

The vertical loading in the posterior capsule of the cat knee has been measured while the knee is rotated into hyperextension. Tissue loading was determined using a previously verified model of the capsule that represents its upper edge as a catenary suspension cable. Tensile loads in the cable were measured using the discharge of mechanoreceptive sensory neurons that had been calibrated as load sensors. The results revealed that the capsule is very lightly loaded in extension rotations. Less than 4% of the applied moment is sustained by the capsule.     

Calibrating joint capsule mechanoreceptors as in vivo soft tissue load cells

A method has been developed whereby the discharge of mechanically sensitive neurons from the cat knee joint capsule can be calibrated and used as load cells. The neurons are located in the upper edge of the capsule which has been previously modeled as a suspension cable and where the loading has been shown to be one dimensional. The calibration procedure relies upon applying known point loads to the cable and measuring its shape. The biomechanical model is then used to compute the cable tension at the neuron location. Results for 20 neurons showed a strong linear relationship between the tension and the frequency of neuronal discharge (r = 0.96, S.D. = 0.05). For 11 of these neurons the in vivo calibration was verified by subsequently excising the posterior capsule and recording from the same neuron while subjecting the cable to measured uniaxial loads. Results showed good agreement between the in vivo and in vitro calibrations. Once calibrated these neurons can be used as load sensors to study in vivo joint loading.     

A biomechanical analysis of prognathous and orthognathous insect head capsules: evidence for a many‐to‐one mapping of form to function

Insect head shapes are remarkably variable, but the influences of these changes on biomechanical performance are unclear. Among ‘basal’ winged insects, such as dragonflies, mayflies, earwigs and stoneflies, some of the most prominent anatomical changes are the general mouthpart orientation, eye size and the connection of the endoskeleton to the head. Here, we assess these variations as well as differing ridge and sclerite configurations using modern engineering methods including multibody dynamics modelling and finite element analysis in order to quantify and compare the influence of anatomical changes on strain in particular head regions and the whole head. We show that a range of peculiar structures such as the genal/subgenal, epistomal and circumocular areas are consistently highly loaded in all species, despite drastically differing morphologies in species with forward‐projecting (prognathous) and downward‐projecting (orthognathous) mouthparts. Sensitivity analyses show that the presence of eyes has a negligible influence on head capsule strain if a circumocular ridge is present. In contrast, the connection of the dorsal endoskeletal arms to the head capsule especially affects overall head loading in species with downward‐projecting mouthparts. Analysis of the relative strains between species for each head region reveals that concerted changes in head substructures such as the subgenal area, the endoskeleton and the epistomal area lead to a consistent relative loading for the whole head capsule and vulnerable structures such as the eyes. It appears that biting‐chewing loads are managed by a system of strengthening ridges on the head capsule irrespective of the general mouthpart and head orientation. Concerted changes in ridge and endoskeleton configuration might allow for more radical anatomical changes such as the general mouthpart orientation, which could be an explanation for the variability of this trait among insects. In an evolutionary context, many‐to‐one mapping of strain patterns onto a relatively similar overall head loading indeed could have fostered the dynamic diversification processes seen in insects.     

Mechanism of lens capsular rupture following blunt trauma: a finite element study

Blunt impact on the eye could results in lens capsular rupture that allows foreign substances to enter into the lens and leads to cataract formation. This paper aimed to investigate the mechanism of lens capsular rupture using finite element (FE) method. A FE model of the human eye was developed to simulate dynamic response of the lens capsule to a BB (a standard 4.5-mm-diameter pellet) impact. Sensitivity studies were conducted to evaluate the effect of the parameters on capsular rupture, including the impact velocity, the elastic modulus of the lens, the thickness and the elastic modulus of the lens capsule. The results indicated that the lens was subjected to anterior compression and posterior intension when the eye was stricken by a BB pellet. The strain on the posterior capsule (0.392) was almost twice as much as that on the anterior capsule (0.207) at an impact velocity of 20 m/s. The strain on the capsule was proportional to the impact velocity, while the capsular strain showed no significant change when the lens modulus elastic varied with age. The findings confirmed that blunt traumatic capsular rupture is the result of shockwave propagation throughout the eye. The posterior capsule is subjected to greater tension in blunt trauma, which is the main cause that ruptures are more commonly found on the posterior capsule than the anterior capsule. Also, thinner thickness and lower elastic modulus would contribute to the posterior capsular rupture.     

Biomechanical response of human spleen in tensile loading

Blunt splenic injuries are most frequently caused as a result of motor vehicle collisions and are associated with high mortality rates. In order to accurately assess the risk of automotive related spleen injuries using tools such as finite element models, tissue level tolerance values and suitable material models must be developed and validated based on appropriate biomechanical data. This study presents a total of 41 tension tests performed on spleen parenchyma coupons and 29 tension tests performed on spleen capsule/parenchyma coupons. Standard dog-bone coupons were obtained from fresh human spleen and tested within 48 h of death. Each coupon was tested once to failure at one of the four loading rates to investigate the effects of rate dependence. Load and acceleration data were obtained at each of the specimen grips. High-speed video and optical markers placed on the specimens were used to measure local displacement. Failure stress and strain were calculated at the location of failure in the gage length of the coupon. The results of the study showed that both the spleen parenchyma and the capsule are rate dependent, with higher loading rates yielding higher failure stresses and lower failure strains. The results also show that the failure stress of the splenic capsule is significantly greater than that of the underlying parenchyma. Overall, this study provides novel biomechanical data that demonstrate the rate dependent tissue level tolerance values of human spleen tissue in tensile loading, which can aid in the improvement of finite element models used to assess injury risk in blunt trauma.     

Dynamic tension spectroscopy and strength of biomembranes

Rupturing fluid membrane vesicles with a steady ramp of micropipette suction produces a distribution of breakage tensions governed by the kinetic process of membrane failure. When plotted as a function of log(tension loading rate), the locations of distribution peaks define a dynamic tension spectrum with distinct regimes that reflect passage of prominent energy barriers along the kinetic pathway. Using tests on five types of giant phosphatidylcholine lipid vesicles over loading rates(tension/time) from 0.01-100 mN/m/s, we show that the kinetic process of membrane breakage can be modeled by a causal sequence of two thermally-activated transitions. At fast loading rates, a steep linear regime appears in each spectrum which implies that membrane failure starts with nucleation of a rare precursor defect. The slope and projected intercept of this regime are set by defect size and frequency of spontaneous formation, respectively. But at slow loading rates, each spectrum crosses over to a shallow-curved regime where rupture tension changes weakly with rate. This regime is predicted by the classical cavitation theory for opening an unstable hole in a two-dimensional film within the lifetime of the defect state. Under slow loading, membrane edge energy and the frequency scale for thermal fluctuations in hole size are the principal factors that govern the level of tension at failure. To critically test the model and obtain the parameters governing the rates of transition under stress, distributions of rupture tension were computed and matched to the measured histograms through solution of the kinetic master (Markov) equations for defect formation and annihilation or evolution to an unstable hole under a ramp of tension. As key predictors of membrane strength, the results for spontaneous frequencies of defect formation and hole edge energies were found to correlate with membrane thicknesses and elastic bending moduli, respectively.     

Mechanical characterisation of in vivo human skin using a 3D force-sensitive micro-robot and finite element analysis

The complex mechanical properties of skin have been the subject of much study in recent years. Several experimental methods developed to measure the mechanical properties of skin in vivo, such as suction or torsion, are unable to measure skin’s anisotropic characteristics. An experiment characterising the mechanical properties of in vivo human skin using a novel force-sensitive micro-robot is presented. The micro-robot applied in-plane deformations to the anterior forearm and the posterior upper arm. The behaviour of the skin in each area is highly nonlinear, anisotropic, and viscoelastic. The response of the upper arm skin is very dependent on the orientation of the arm. A finite element model consisting of an Ogden strain energy function and quasi-linear viscoelasticity was developed to simulate the experiments. An orthogonal initial stress field, representing the in vivo skin tension, was used as an additional model parameter. The model simulated the experiments accurately with an error-of-fit of 17.5% for the anterior lower forearm area, 6.5% for the anterior upper forearm and 9.3% for the posterior upper arm. The maximum in vivo tension in each area determined by the model was 6.2 Nm⁻¹ in the anterior lower forearm, 11.4 Nm⁻¹ in anterior upper forearm and 5.6 Nm⁻¹ in the posterior upper arm. The results also show that a finite element model with a neo-Hookean strain energy function cannot simulate the experiments with the same accuracy.     

Changes to the mechanical properties of the glenohumeral capsule during anterior dislocation

The glenohumeral joint is the most frequently dislocated major joint in the body, and instability due to permanent deformation of the glenohumeral capsule is a common pathology. The corresponding change in mechanical properties may have implications for the ideal location and extent of plication, which is a common clinical procedure used to repair the capsule. Therefore, the objective of this study was to quantify the mechanical properties of four regions of the glenohumeral capsule after anterior dislocation and compare the properties to the normal glenohumeral capsule. Six fresh-frozen cadaveric shoulders were dislocated in the anterior direction with the joint in the apprehension position using a robotic testing system. After dislocation, mechanical testing was performed on the injured glenohumeral capsule by loading the tissue samples in tension and shear. An inverse finite element optimization routine was used to simulate the experiments and obtain material coefficients for each tissue sample. Cauchy stress–stretch curves were then generated to represent the mechanical response of each tissue sample to theoretical loading conditions. Based on several comparisons (average of the material coefficients, average stress–stretch curve for each region, and coefficients representing the average curves) between the normal and injured tissue samples, the mechanical properties of the injured tissue samples from multiple regions were found to be lower than those of the normal tissue in tension but not in shear. This finding indicates that anterior dislocation primarily affects the tensile behavior of the glenohumeral capsule rather than the shear behavior, and this phenomenon could be caused by plastic deformation of the matrix, permanent collagen fiber rotation, and/or collagen fiber failure. These results suggest that plication and suturing may not be sufficient to return stability to the shoulder after dislocation in all individuals. Thus, surgeons may need to perform a procedure that reinforces or stiffens the tissue itself, such as reconstruction or augmentation, to improve repair procedures.     

The effect of plant growth substances on the development of tension wood in horizontally inclined stems ofAcer rubrum seedlings

Summary In horizontally placedAcer rubrum seedlings the development of tension wood is inhibited by auxin especially when applied along the upper side of the axis. Treatment separately with GA and K does not alter the normal pattern of tension wood formation. The development of tension wood appears to be correlated with a reduced auxin level on the upper side of the stem.Geotropic reorientation of the woody stem ofAcer rubrum seedlings that are placed in the horizontal position is related closely to the amount of tension wood that is formed on the upper side of the axis. Evidence is discussed which indicates that tension wood itself participates actively in the reorientation mechanism.The following abbreviations will be used TIBA (2,3,5-tri-iodobenzoic acid) - IAA (indole-3-acetic acid) - GA (gibberellic acid) - NAA (naphthaleneacetic acid) - 2,4-D (2,4-dichloro-phenoxyacetic acid) - K (kinetin) This material was included in a doctoral thesis submitted by P. R.Morey to the graduate school of Yale University, New Haven.     

Mechanical properties of brain tissue in tension

This paper contains experimental results of in vitro, uniaxial tension of swine brain tissue in finite deformation as well as proposes a new hyper-viscoelastic constitutive model for the brain tissue. The experimental results obtained for two loading velocities, corresponding to strain rates of 0.64 and 0.64 x 10(-2)s(-1), are presented. We believe that these are the first ever experiments of this kind. The applied strain rates were similar to those applied in our previous study, focused on explaining brain tissue properties in compression. The stress-strain curves are convex downward for all extension rates. The tissue response stiffened as the loading speed increased, indicating a strong stress-strain rate dependence. Swine brain tissue was found to be considerably softer in extension than in compression. Previously proposed in the literature brain tissue constitutive models, developed based on experimental data collected in compression are shown to be inadequate to explain tissue behaviour in tension. A new, non-linear, viscoelastic model based on the generalisation of the Ogden strain energy hyper-elastic constitutive equation is proposed. The new model accounts well for brain tissue deformation behaviour in both tension and compression (natural strain in <-0.3,0.2>) for strain rates ranging over five orders of magnitude.     

A micromechanically-based, three-dimensional interface finite element for the modelling of the periodontal ligament

Some ideas are presented for the implementation of an interface finite element capable to model in 3-dimensions several mechanical features of the periodontal ligament. Such an element is based on a simple 2-cable micromechanical model, able to reproduce the periodontal ligament stiffness and strength under any loading condition, including the pure torsion of a tooth. A single cable represents a sufficiently populated sample of collagen fibres, each with an initially crimped geometry; a single collagen fibre can provide a mechanical response, in tension, only when it is completely uncoiled. The macroscopic interface behaviour is obtained by statistical integrations over the uncoiled length of each collagen fibre, up to the fibre failure. Such a model can reproduce the periodontal ligament anisotropy due to the variable fibre orientation along the tooth root, its different behaviour in tension/compression/shear, its different behaviour for extrusive/intrusive loading, and so forth. Some numerical examples illustrate the potentialities of this interface element, quite simple in essence but rather complete from an engineering viewpoint.     

Functional anatomy of vagina muscles in the blood-feeding insect,Rhodnius prolixus

The physiology of the muscles associated with the vagina in the blood-feeding insect, Rhodnius prolixus Stal, was investigated with the use of Methylene Blue staining to visualize the anatomy, and a micro force transducer to record spontaneous and neurally-evoked contractions. The vagina is associated with a dorsal muscle and a set of paired lateral muscles. The dorsal muscle extends from the base of the common oviduct to apodemes located laterally on sternite VIII, the first genital segment. The lateral muscles extend from a medially-located apodeme on the posterior edge of sternite VI around each side of the common oviduct to travel posteriorly along the side of the vagina before inserting laterally on apodemes on sternite VIII. The vagina muscles display spontaneous and neurally-evoked contractions that are prolonged but transient. The response to evoked contractions shows that the muscles are innervated by both excitatory and inhibitory motor axons. The degree of tension generated by evoked contractions is dependent on the frequency of stimulation with maximal tension being generated at 20–30 Hz. This tension, which often exceeds 400 mg, is transient and returns to a baseline within 1 to 2 min during continuous stimulation. These results, which are the first to describe this chamber in this well-studied insect, are discussed with respect to the act of egg laying.     

Dynamic analysis of actin cable function during Drosophila dorsal closure

Throughout development, a series of epithelial movements and fusions occur that collectively shape the embryo. They are dependent on coordinated reorganizations and contractions of the actin cytoskeleton within defined populations of epithelial cells. One paradigm morphogenetic movement, dorsal closure in the Drosophila embryo, involves closure of a dorsal epithelial hole by sweeping of epithelium from the two sides of the embryo over the exposed extraembryonic amnioserosa to form a seam where the two epithelial edges fuse together. The front row cells exhibit a thick actin cable at their leading edge. Here, we test the function of this cable by live analysis of GFP-actin-expressing embryos in which the cable is disrupted by modulating Rho1 signaling or by loss of non-muscle myosin (Zipper) function. We show that the cable serves a dual role during dorsal closure. It is contractile and thus can operate as a "purse string," but it also restricts forward movement of the leading edge and excess activity of filopodia/lamellipodia. Stripes of epithelium in which cable assembly is disrupted gain a migrational advantage over their wild-type neighbors, suggesting that the cable acts to restrain front row cells, thus maintaining a taut, free edge for efficient zippering together of the epithelial sheets.     

Asymmetric distribution of Echinoid defines the epidermal leading edge during Drosophila dorsal closure

During Drosophila melanogaster dorsal closure, lateral sheets of embryonic epidermis assemble an actomyosin cable at their leading edge and migrate dorsally over the amnioserosa, converging at the dorsal midline. We show that disappearance of the homophilic cell adhesion molecule Echinoid (Ed) from the amnioserosa just before dorsal closure eliminates homophilic interactions with the adjacent dorsal-most epidermal (DME) cells, which comprise the leading edge. The resulting planar polarized distribution of Ed in the DME cells is essential for the localized accumulation of actin regulators and for actomyosin cable formation at the leading edge and for the polarized localization of the scaffolding protein Bazooka/PAR-3. DME cells with uniform Ed fail to assemble a cable and protrude dorsally, suggesting that the cable restricts dorsal migration. The planar polarized distribution of Ed in the DME cells thus provides a spatial cue that polarizes the DME cell actin cytoskeleton, defining the epidermal leading edge and establishing its contractile properties.     

A model of tension and compression cracks with cohesive zone at a bone-cement interface

This paper gives an insight about compression and tension cracks as encountered at a bone-cement interface. Within the context of continuum theory of fracture, an analytical solution is presented for the problem of a bimaterial interface edge crack under uniaxial tension or compression, assuming no tangential slip along the crack faces since cement pedicles penetrate into the cancellous bone several millimeters. Also essential to the solution are cohesive zone effects that account for a strengthening mechanism over the crack faces. The solution provides a methodological framework for quantifying the influence of the cohesive zone on the magnitude of the stress singularity. Mode I crack tip stress intensity factors are calculated at different stages of the loading and unloading phases under uniaxial tension or compression. Finally, an inelastic mechanism is presented that gives theoretical support to explain the formation of interfacial compression cracks, a phenomenon that was not previously appreciated and that arises from the rigid cement being forced into the more compliant cancellous bone.     

Xylem-specific and tension stress-responsive coexpression of KORRIGAN endoglucanase and three secondary wall-associated cellulose synthase genes in aspen trees

In nature, angiosperm trees develop tension wood on the upper side of their leaning trunks and drooping branches. Development of tension wood is one of the straightening mechanisms by which trees counteract leaning or bending of stem and resume upward growth. Tension wood is characterized by the development of a highly crystalline cellulose-enriched gelatinous layer next to the lumen of the tension wood fibers. Thus experimental induction of tension wood provides a system to understand the process of cellulose biosynthesis in trees. Since KORRIGAN endoglucanases (KOR) appear to play an important role in cellulose biosynthesis in Arabidopsis, we cloned PtrKOR, a full-length KOR cDNA from aspen xylem. Using RT-PCR, in situ hybridization, and tissue-print assays, we show that PtrKOR gene expression is significantly elevated on the upper side of the bent aspen stem in response to tension stress while KOR expression is significantly suppressed on the opposite side experiencing compression stress. Moreover, three previously reported aspen cellulose synthase genes, namely, PtrCesA1, PtrCesA2, and PtrCesA3 that are closely associated with secondary cell wall development in the xylem cells exhibited similar tension stress-responsive behavior. Our results suggest that coexpression of these four proteins is important for the biosynthesis of highly crystalline cellulose typically present in tension wood fibers. Their simultaneous genetic manipulation may lead to industrially relevant improvement of cellulose in transgenic crops and trees.Suchita Bhandari and Takeshi Fujino contributed equally to this research.     

An analysis of the changes in growth rate occurring during the initial stages of geocurvature in shoots

Abstract A detailed study of the changes in growth rate on the two sides of a shoot prior to, and following geostimulation has been undertaken. Data from etiolated Zea seedlings, and cucumber hypocotyls, and from light grown sunflower hypocotyls are presented. In all cases, the differential growth which brings about geocurvature begins simultaneously along the length of the organ. This is contrary to previous reports in the literature which suggested that curvature begins first at the tip of an organ and progresses basipetally. The feature which is common to all species investigated is that growth of the upper side of the shoot ceases following geostimulation. In some cases there is also a marked acceleration in growth rate on the lower side of the shoot (sunflower) but other species show no such acceleration of growth (cucumber). It has been assumed for many years that the major factor causing upward curvature was an acceleration of growth on the lower side of the organ. The data presented here show that the cessation of growth on the upper side is a major, and in some cases the only factor bringing about geocurvature. The data are discussed in relation to the mechanisms which might control geotropic curvature.     

Anatomic features of postmortem experimental ruptures of the human heart

Comparison of postmortem performed experimental cardiac ruptures with post-infarction lesions reveals uniformity of their localization. The ruptures are found to occur at places of a sharp change in the relief of the cardiac internal surface. These areas should be considered as concentrators of strain, promoting cardiac ruptures. In the left ventricle six concentrators of strain are revealed. They are: the place where the anterior part of the interventricular septum passes into the anterior wall of the left ventricle, the right edge of the papillary muscle, the left edge of the anterior papillary muscle, the left edge of the posterior papillary muscle, the right edge of the posterior papillary muscle, the place where the posterior part of the interventricular septum passes into the posterior wall of the left ventricle. Frequency of the experimental ruptures of the interventricular septum, under loading of the left ventricle, is demonstrated to depend on pressure in the right cardiac part.     

江苏溧阳夏林似剑齿虎一新种

<正> 夏林石灰厂因采石料,裂隙堆积屡见剑齿虎类化石出露。1977年8月,笔者对产地作了短期发掘,在附近采获一颗似剑齿虎下门齿及少许小型食草偶蹄类臼齿碎片。于挖掘期间,学生朱志洪将他所釆一枚完整的似剑齿虎上犬齿化石热诚相赠,盛情可嘉。本文承蒙刘东生教授的支持和指导,深表感谢。保存在南京地质陈列馆的材料,为Homotherium。     

A quantitative model of cellular elasticity based on tensegrity

A tensegrity structure composed of six struts interconnected with 24 elastic cables is used as a quantitative model of the steady-state elastic response of cells, with the struts and cables representing microtubules and actin filaments, respectively. The model is stretched uniaxially and the Young's modulus (E0) is obtained from the initial slope of the stress versus strain curve of an equivalent continuum. It is found that E0 is directly proportional to the pre-existing tension in the cables (or compression in the struts) and inversely proportional to the cable (or strut) length square. This relationship is used to predict the upper and lower bounds of E0 of cells, assuming that the cable tension equals the yield force of actin (approximately 400 pN) for the upper bound, and that the strut compression equals the critical buckling force of microtubules for the lower bound. The cable (or strut) length is determined from the assumption that model dimensions match the diameter of probes used in standard mechanical tests on cells. Predicted values are compared to reported data for the Young's modulus of various cells. If the probe diameter is greater than or equal to 3 microns, these data are closer to the lower bound than to the upper bound. This, in turn, suggests that microtubules of the CSK carry initial compression that exceeds their critical buckling force (order of 10(0)-10(1) pN), but is much smaller than the yield force of actin. If the probe diameter is less than or equal to 2 microns, experimental data fall outside the region defined by the upper and lower bounds.