Optimisation of integrated biodiesel production. Part II: a study of the material balance

A study was made of the material balance for the fatty acid methyl ester (biodiesel) synthesis from sunflower oil using potassium hydroxide as the catalyst. A factorial design of experiments and a central composite design have been used to evaluate the influence of operating conditions on the process material balance. The responses chosen were the biodiesel yield and the yield losses due to triglyceride saponification and methyl ester dissolution in glycerol, while the variables studied were temperature, initial catalyst concentration and the methanol:vegetable oil molar ratio. The biodiesel yield increased and therefore the yield losses decreased by decreasing catalyst concentration and temperature. However, the methanol:sunflower oil molar ratio did not affect the material balance variables significantly. Second-order models were obtained to predict the biodiesel yield and both yield losses. Within the experimental range studied, these models largely matched the results from the experiments.     

Ultrasonic monitoring of glycerol settling during transesterification of soybean oil

A low-intensity ultrasonic measurement system was used to monitor the products of transesterification of soybean oil in methanol to FAME (biodiesel). The byproducts of the transesterification reaction are methyl esters, glycerol and other products. During the transesterification reaction, the glycerol, having a higher density than the methyl ester, settles at the bottom of the reaction vessel. The aim of this study was to measure the glycerol deposition rate during transesterification and to assess the reaction rate and end time. Soybean oil was converted into biodiesel at four temperature levels. The amount of catalyst (KOH) used in the transesterification reactions was determined by titration. The ultrasonic waveforms captured during the reaction were recorded and analyzed automatically. The ultrasonic system monitored the effects of reaction temperatures on the glycerol settling rate and the reaction end times. The ultrasonic measurement of glycerol settling would be a useful non-destructive method for evaluating the effects of parameters such as catalyst amount, mixing time and temperature on transesterification reactions.     

Influence of fatty acid composition of raw materials on biodiesel properties

The aim of this work was the study of the influence of the raw material composition on biodiesel quality, using a transesterification reaction. Thus, ten refined vegetable oils were transesterificated using potassium methoxide as catalyst and standard reaction conditions (reaction time, 1h; weight of catalyst, 1 wt.% of initial oil weight; molar ratio methanol/oil, 6/1; reaction temperature, 60 degrees C). Biodiesel quality was tested according to the standard [UNE-EN 14214, 2003. Automotive fuels. Fatty acid methyl esters (FAME) for diesel engines. Requirements and test methods]. Some critical parameters like oxidation stability, cetane number, iodine value and cold filter plugging point were correlated with the methyl ester composition of each biodiesel, according to two parameters: degree of unsaturation and long chain saturated factor. Finally, a triangular graph based on the composition in monounsaturated, polyunsaturated and saturated methyl esters was built in order to predict the critical parameters of European standard for whatever biodiesel, known its composition.     

Dimethyl carbonate as potential reactant in non-catalytic biodiesel production by supercritical method

In this study, the non-catalytic supercritical method has been studied in utilizing dimethyl carbonate. It was demonstrated that, the supercritical dimethyl carbonate process without any catalysts applied, converted triglycerides to fatty acid methyl esters with glycerol carbonate and citramalic acid as by-products, while free fatty acids were converted to fatty acid methyl esters with glyoxal. After 12 min of reaction at 350 degrees C/20 MPa, rapeseed oil treated with supercritical dimethyl carbonate reached 94% (w/w) yield of fatty acid methyl ester. The by-products from this process which are glycerol carbonate and citramalic acid are much higher in value than glycerol produced by the conventional process. In addition, the yield of the fatty acid methyl esters as biodiesel was almost at par with supercritical methanol method. Therefore, supercritical dimethyl carbonate process can be a good candidate as an alternative biodiesel production process.     

Transesterification of canola oil in mixed methanol/ethanol system and use of esters as lubricity additive

Transesterification of canola oil was carried out with methanol, ethanol, and various mixtures of methanol/ethanol, keeping the molar ratio of oil to alcohol 1:6 and using KOH as a catalyst. Mixtures of alcohol increased the rate of transesterification reaction and produced methyl as well as ethyl esters. The increased rate was result of better solubility of oil in reaction mixture due to better solvent properties of ethanol than methanol and equilibrium due to methanol. With 3:3 molar ratio of methanol to ethanol {MEE (3:3)} the amount of ethyl ester formed was 50% that of methyl ester. Properties (acid value, viscosity, density) of all esters including mixed esters were within the limits of ASTM standards. Lubricities of these esters are in the order: ethyl ester>methyl ethyl ester>methyl ester.     

Optimization of alkali-catalyzed transesterification of Pongamia pinnata oil for production of biodiesel

Studies were carried out on transesterification of Karanja oil with methanol for the production of biodiesel. The reaction parameters such as catalyst concentration, alcohol/oil molar ratio, temperature, and rate of mixing were optimized for production of Karanja oil methyl ester (KOME). The fatty acid methyl esters content in the reaction mixture were quantified by HPLC and 1H NMR method. The yield of methyl esters from Karanja oil under the optimal condition was 97-98%.     

Preparation of biodiesel from crude oil of Pongamia pinnata

Biodiesel was prepared from the non-edible oil of Pongamia pinnata by transesterification of the crude oil with methanol in the presence of KOH as catalyst. A maximum conversion of 92% (oil to ester) was achieved using a 1:10 molar ratio of oil to methanol at 60 degrees C. Tetrahydrofuran (THF), when used as a co-solvent increased the conversion to 95%. Solid acid catalysts viz. Hbeta-Zeolite, Montmorillonite K-10 and ZnO were also used for this transesterification. Important fuel properties of methyl esters of Pongamia oil (Biodiesel) compare well (Viscosity = 4.8 Cst @ 40 degrees C and Flash point = 150 degrees C) with ASTM and German biodiesel standards.     

Transesterification of palm oil to methyl ester on activated carbon supported calcium oxide catalyst

In this study, methyl ester (ME) was produced by transesterification of palm oil (CPO) (cooking grade) using activated carbon supported calcium oxide as a solid base catalyst (CaO/AC). Response surface methodology (RSM) based on central composite design (CCD) was used to optimize the effect of reaction time, molar ratio of methanol to oil, reaction temperature and catalyst amount on the transesterification process. The optimum condition for CPO transesterification to methyl ester was obtained at 5.5 wt.% catalyst amount, 190 °C temperature, 15:1 methanol to oil molar ratio and 1 h 21 min reaction time. At the optimum condition, the ME content was 80.98%, which is well within the predicted value of the model. Catalyst regeneration studies indicate that the catalyst performance is sustained after two cycles.     

Production of biodiesel and lactic acid from rapeseed oil using sodium silicate as catalyst

Biodiesel and lactic acid from rapeseed oil was produced using sodium silicate as catalyst. The transesterification in the presence of the catalyst proceeded with a maximum yield of 99.6% under optimized conditions [3% (w/w) sodium silicate, methanol/oil molar ratio 9/1, reaction time 60 min, reaction temperature 60 °C, and stirring rate 250 rpm]. After six consecutive transesterification reactions, the catalyst was collected and used for catalysis of the conversion of glycerol to lactic acid. A maximum yield of 80.5% was achieved when the reaction was carried out at a temperature of 300 °C for 90 min. Thus, sodium silicate is an effective catalyst for transesterification and lactic acid production from the biodiesel by-product, glycerol.     

Synthesis of fatty acid methyl ester from palm oil (Elaeis guineensis) with Ky(MgCa)2xO3 as heterogeneous catalyst

Fatty acid methyl esters (FAME) were produced from palm oil using eggshell modified with magnesium and potassium nitrates to form a composite, low-cost heterogeneous catalyst for transesterification. The catalyst, prepared by the combination of impregnation/co-precipitation was calcined at 830 °C for 4 h. Transesterification was conducted at a constant temperature of 65 °C in a batch reactor. Design of experiment (DOE) was used to optimize the reaction parameters, and the conditions that gave highest yield of FAME (85.8%) was 5.35 wt.% catalyst loading at 4.5 h with 16:1 methanol/oil molar ratio. The results revealed that eggshell, a solid waste, can be utilized as low-cost catalyst after modification with magnesium and potassium nitrates for biodiesel production.     

Synthesis of fatty acid methyl ester from used vegetable cooking oil by solid reusable Mg 1-x Zn 1+x O2 catalyst

Fatty acid methyl ester was produced from used vegetable cooking oil using Mg_1−x Zn_1+xO₂ solid catalyst and the performance monitored in terms of ester content obtained. Used vegetable cooking oil was employed to reduce operation cost of biodiesel. The significant operating parameters which affect the overall yield of the process were studied. The highest ester content, 80%, was achieved with the catalyst during 4 h 15 min reaction at 188 °C with methanol to oil ratio of 9:1 and catalyst loading of 2.55 wt% oil. Also, transesterification of virgin oil gave higher yield with the heterogeneous catalyst and showed high selectivity towards ester production. The used vegetable cooking oil did not require any rigorous pretreatment. Catalyst stability was examined and there was no leaching of the active components, and its performance was as good at the fourth as at the first cycle.     

Transesterification of soybean oil using combusted oyster shell waste as a catalyst

Transesterification of soybean oil catalyzed by combusted oyster shell, which is waste material from shellfish farms, was examined. Powdered oyster shell combusted at a temperature above 700 degrees C, at which point the calcium carbonate of oyster shell transformed to calcium oxide, acted as a catalyst in the transesterification of soybean oil. On the basis of factorial design, the reaction conditions of catalyst concentration and reaction time were optimized in terms of the fatty acid methyl ester concentration expressed as biodiesel purity. Under the optimized reaction conditions of a catalyst concentration and reaction time of 25wt.%. and 5h, respectively, the biodiesel yield, expressed relative to the amount of soybean oil poured into the reaction vial, was more than 70% with high biodiesel purity. These results indicate oyster shell waste combusted at high temperature can be reused in biodiesel production as a catalyst.     

Biodiesel production from high acid value waste frying oil catalyzed by superacid heteropolyacid

Transesterification of waste cooking oil with high acid value and high water contents using heteropolyacid H3PW12O40 x 6H2O (PW12) as catalyst was investigated. The hexahydrate form of PW(12) was found to be the most promising catalyst which exhibited highest ester yield 87% for transesterification of waste cooking oil and ester yield 97% for esterification of long-chain palmitic acid, respectively. The PW12 acid catalyst shows higher activity under the optimized reaction conditions compared with conventional homogeneous catalyst sulfuric acid, and can easily be separated from the products by distillation of the excess methanol and can be reused more times. The most important feature of this catalyst is that the catalytic activity is not affected by the content of free fatty acids (FFAs) and the content of water in the waste cooking oil and the transesterification can occur at a lower temperature (65 degrees C), a lower methanol oil ratio (70:1) and be finished within a shorter time. The results illustrate that PW12 acid is an excellent water-tolerant and environmentally benign acid catalyst for production of biodiesel from waste cooking oil.     

Acceleration of catalytic activity of calcium oxide for biodiesel production

This research was aimed at studying the acceleration of the catalytic activity of calcium oxide (CaO) for developing an effective heterogeneous catalyst for biodiesel production by the transesterification of plant oil with methanol. CaO was activated by pretreatment with methanol and was used for the transesterification reaction. The activation and transesterification reaction conditions were examined. The obtained optimal reaction conditions were 0.1-g CaO, 3.9-g methanol, 15-g rapeseed oil, and 1.5-h activation time at room temperature that provided methyl ester in approximately 90% yield within a reaction time of 3h at 60 degrees C. The activation mechanism was also investigated, and the proposed mechanism is as follows. By pretreatment with methanol, a small amount of CaO gets converted into Ca(OCH(3))(2) that acts as an initiating reagent for the transesterification reaction and produces glycerin as a by-product. Subsequently, a calcium-glycerin complex, formed due to the reaction of CaO with glycerin, functions as the main catalyst and accelerates the transesterification reaction.     

Kinetics and mechanism of the cutinase-catalyzed transesterification of oils in AOT reversed micellar system

The kinetics of the enzymatic transesterification between a mixture of triglycerides (oils) and methanol for biodiesel production in a bis(2-ethylhexyl) sodium sulfosuccinate (AOT)/isooctane reversed micellar system, using recombinant cutinase from Fusarium solani pisi as a catalyst, was investigated. In order to describe the results that were obtained, a mechanistic scheme was proposed, based on the literature and on the experimental data. This scheme includes the following reaction steps: the formation of the active enzyme–substrate complex, the addition of an alcohol molecule to the complex followed by the separation of a molecule of the fatty acid alkyl ester and a glycerol moiety, and release of the active enzyme. Enzyme inhibition and deactivation effects due to methanol and glycerol were incorporated in the model. This kinetic model was fitted to the concentration profiles of the fatty acid methyl esters (the components of biodiesel), tri-, di- and monoglycerides, obtained for a 24 h transesterification reaction performed in a stirred batch reactor under different reaction conditions of enzyme and initial substrates concentration.     

A novel enzymatic route for biodiesel production from renewable oils in a solvent-free medium

A new enzymatic route for biodiesel production from soybean oil was developed using methyl acetate as a novel acyl acceptor. Novozym 435 (immobilized Candida antarctica lipase) gave the highest methyl ester (ME) yield of 92%. The optimum conditions of the transesterification were 30% enzyme based on oil weight; a molar ratio of methyl acetate/oil of 12:1; temperature 40 °C and reaction time 10 h. Since no glycerol was produced in the process, this method is very convenient for recycling the catalyst and by-product triacetylglycerol showed no negative effect on the fuel property.     

Enzyme catalyzed transesterification of waste cooking oil with dimethyl carbonate

The detrimental effects of waste cooking oil on sewer system attracted attention toward its proper management and reusing this waste oil for making biodiesel provides commercial and environmental advantage. In the present study, biodiesel has been successfully produced from waste cooking oil and dimethyl carbonate by transesterification, instead of the conventional alcohol. In this optimization study, the effect of various reaction conditions such as solvent, time and temperature, molar ratio of DMC to oil, enzyme loading and reusability, on the yield of fatty acid methyl ester (FAME) has been studied. The Maximum conversion of FAMEs achieved was 77.87% under optimum conditions (solvent free system, reaction time of 24 h, 60 °C, molar ratio of DMC to oil 6:1, catalyst amount 10% Novozym 435 (based on the oil weight)). Moreover, there was no obvious loss in the conversion after lipases were reused for 6 batches under optimized conditions.     

Rapeseed oil methyl esters preparation using heterogeneous catalysts

The classical method of fatty acids methyl esters (FAME) production is based on triglyceride transesterification to methyl esters. Sodium hydroxide dissolved in methanol is used as a catalyst. The purpose of this work was to examine a heterogeneous catalyst, in particular calcium compounds, to produce methyl esters of rapeseed oil. This research showed that the transesterification of rapeseed oil by methyl alcohol can be catalysed effectively by basic alkaline-earth metal compounds: calcium oxide, calcium methoxide and barium hydroxide. Calcium catalysts, due to their weak solubility in the reaction medium, are less active than sodium hydroxide. However, calcium catalysts are cheaper and lead to decreases in the number of technological stages and the amount of unwanted waste products. It was found that the transesterification reaction rate can be enhanced by ultrasound as well as by introducing an appropriate reagent into a reactor to promote methanol solubility in the rapeseed oil. Tetrahydrofuran was used as additive to accelerate the transesterification process.     

Lipase-catalyzed simultaneous biosynthesis of biodiesel and glycerol carbonate from corn oil in dimethyl carbonate

Biodiesel [fatty acid methyl esters (FAMEs)] and glycerol carbonate were synthesized from corn oil and dimethyl carbonate (DMC) via transesterification using lipase (Novozyme 435) in solvent-free reaction in which excess DMC was used as the substrate and reaction medium. Glycerol carbonate was also simultaneously formed from DMC and glycerol. Conversions of FAMEs and glycerol carbonate were examined in batch reactions. The FAMEs and glycerol carbonate reached 94 and 62.5% from oil and DMC (molar ratio of 1:10) with 0.2% (v/v) water and 10% (w/w) Novozyme 435 (based on oil weight) at 60°C. When Novozyme 435 was washed with acetone after each reaction, more than 80% activity still remained after seven recycling.     

Glycerol extracting dealcoholization for the biodiesel separation process

By means of utilizing sunflower oil and Jatropha oil as raw oil respectively, the biodiesel transesterification production and the multi-stage extracting separation were carried out experimentally. Results indicate that dealcoholized crude glycerol can be utilized as the extracting agent to achieve effective separation of methanol from the methyl ester phase, and the glycerol content in the dealcoholized methyl esters is as low as 0.02 wt.%. For the biodiesel separation process utilizing glycerol extracting dealcoholization, its technical and equipment information were acquired through the rigorous process simulation in contrast to the traditional biodiesel distillation separation process, and results show that its energy consumption decrease about 35% in contrast to that of the distillation separation process. The glycerol extracting dealcoholization has sufficient feasibility and superiority for the biodiesel separation process.