Protein production from whey usingPenicillium cyclopium; growth parameters and cellular composition

Summary The growth parameters ofPenicillium cyclopium have been evaluated in a continuous culture system for the production of fungal protein from whey. Dilution rates varied from 0.05 to 0.20 h^–1 under constant conditions of temperature (28°C) and pH (3.5). The saturation coefficients in the Monod equation were 0.74 g l^–1 for lactose and 0.14 mg l^–1 for oxygen, respectively. For a wide range of dilution rates, the yield was 0.68 g g^–1 biomass per lactose and the maintenance coefficient 0.005 g g^–1 h^–1 lactose per biomass, respectively. The maximum biomass productivity achieved was 2 g l^–1 h^–1 biomass at dilution rates of 0.16–0.17 h^–1 with a lactose concentration of 20 g l^–1 in the feed. The crude protein and total nucleic acid contents increased with a dilution rate, crude protein content varied from 43% to 54% and total nucleic acids from 6 to 9% in the range of dilution rates from 0.05 to 0.2 h^–1, while the Lowry protein content was almost constant at approximately 37.5% of dry matter.Nomenclature (mg l^–1) C_o initial concentration of dissolved oxygen - (h^–1) D dilution rate - (mg l^–1) K₀₂ saturation coefficient for oxygen - (g l^–1) K_s saturation coefficient for substrate - (g g^–1 h^–1) lactose per biomass) m maintenance energy coefficient - (mM g^–1 h^–1O₂ per biomass) Q₀₂ specific oxygen uptake rate - (g l^–1) S residual substrate concentration at steady state - (g l^–1) S_o initial substrate concentration in feed - (min) t_1/2 time when C_o is equal to C_o/2 - (g l^–1) X biomass concentration - (g l^–1) X biomass concentration at steady state - (g g^–1 biomass per lactose) Y_G yield coefficient for cell growth - (g g^–1 biomass per lactose) Y_x/s overall yield coefficient - (h^–1) specific growth rate     

Influence of temperature rise on kinetic parameters during batch propagation of Kluyveromyces fragilis in cheese whey under ambient conditions

Three 5 l working volume fermenters were used to investigate the growth of the yeast Kluyveromyces fragilis in acid cheese whey under ambient temperature in order to assess the specific growth rate and yield, the lactose and oxygen uptake rates during the various phases of batch culture, the effect of increasing temperature on the various kinetic parameters, and the need for a cooling unit for single cell production batch systems. The initial dissolved oxygen in the medium was 5.5 mg l^–1 and the pH was maintained at 4.5. The observed lag phase, specific growth rate and maximum cell number were 4 h, 0.2 h^–1 and 8.4 × 10⁸ cells ml^–1, respectively. About 99% of the lactose in cheese whey was utilized within 20 h, 85% during the exponential growth phase. The specific lactose utilization rates by K. fragilis were 0.20 × 10^–12, 1.457 × 10^–12, 0.286 × 10^–12 and 0.00 g lactose cell^–1 h^–1, for the lag, exponential, stationary and death phases, respectively. The dissolved oxygen concentration in the medium decreased as the cell number increased. The lowest oxygen concentration of 1.2 mg l^–1 was observed during the stationary phase. The volumetric oxygen transfer coefficient was 0.41 h^–1 and the specific oxygen uptake rates were 0.32 × 10^–12, 2.14 × 10^–12, 0.51 × 10^–12 and 0.003 × 10^–12 mg O₂ cell^–1 h^–1, for the lag, exponential, stationary and death phases, respectively. The maximum temperature recorded for the medium was 33 °C, indicating that a cooling unit for batch production of single cell protein at ambient temperature is not needed for this type of bioreactor. The increase in medium temperature affected the cell growth and the lactose and oxygen uptake rates.     

Conversion of cellulose into fungal cell mass

Summary Chaetomium cellulolyticum (ATCC 32319) was cultivated on glucose, Avicel and/or Sigmacell in a 20-1 stirred tank batch reactor. The substrate (cellulose) concentration, the cell mass concentration (through protein and/or nitrogen content), reducing sugar concentration, the enzyme activity, the alkali consumption rate, the dissolved O₂ and CO₂ concentrations in the outlet gas were measured. The specific growth rate, the substrate yield coefficient, cell productivity, the oxygen consumption rate, the CO₂ production rate and the volumetric mass transfer coefficient were determined. At the beginning of the growth phase the oxygen utilization rate exhibits a sharp maximum. This maximum could be used to start process control. Because of the long lag phase periodic batch operation is recommended.Symbols CP cell protein concentration (g l^–1) - FPA FP enzyme activity (IU l^–1) - GP dissolved protein concentration (g l^–1) - IU international unit of enzyme activity - k_La volumetric mass tranfer coefficient (h^–1) - LG alkali (1 n NaOH) consumption (ml) - LGX specific alkali consumption rate per cell mass (ml g^–1 h^–1) - P cell mass productivity (g l^–1 h^–1) - specific oxygen consumption rate per cell mass (g g^–1 h^–1) - Q aeration rate (volumetric gas flow rate per volume of medium, vvm) (min^–1) - N impeller speed (revolution per minute, rpm) (min^–1) - S substrate concentration (g l^–1) - S⁰ S at t_F=0 (g l^–1) - S₀ S in feed (g l^–1) - SR acid consumption (ml) - TDW total dry weight (g l^–1) - T temperature (° C) - t_F cultivation time (h) - U substrate conversion - X cell mass concentration (g l^–1) - Y_X/S vield coefficient - specific growth rate (h^–1) - _m maximum specific growth rate (h^–1)     

Studies on the variables and kinetics of SCP production from nopal fruit juice

Summary Submerged batch cultivation under controlled environmental conditions of pH 3.8, temperature 30°C, and K_La200 h^–1 (above 180 mMO₂ l ^–1 h^–1 oxygen supply rate) produced a maximum (12.0 g·l ^–1) SCP (Candida utilis) yield on the deseeded nopal fruit juice medium containing C/N ratio of 7.0 (initial sugar concentration 25 g·l ^–1) with a yield coefficient of 0.52 g cells/g sugar. In continuous cultivation, 19.9 g·l ^–1 cell mass could be obtained at a dilution rate (D) of 0.36 h^–1 under identical environmental conditions, showing a productivity of 7.2 g·l ^–1·h^–1. This corresponded to a gain of 9.0 in productivity in continuous culture over batch culture. Starting with steady state values of state variables, cell mass (C_X–19.9 g·l ^–1), limiting nutrient concentration (C_ln–2.5 g·l ^–1) and sugar concentration (C_S–1.5 g·l ^–1) at control variable conditions of pH 3.8, 30°C, and K_La 200 h^–1 keeping D=0.36 h^–1 as reference, transient response studies by step changes of these control variables also showed that this pH, temperature and K_La conditions are most suitable for SCP cultivation on nopal fruit juice. Kinetic equations obtained from experimental data were analysed and kinetic parameters determined graphically. Results of SCP production from nopal fruit juice are described.Nomenclature C_ln concentration of ammonium sulfate (g·l ^–1) - C_S concentration of total sugar (g·l ^–1) - C_X cell concentration (g·l ^–1) - D dilution rate (h^–1) - K_ln Monod's constant (g·l ^–1) - m maintenance coefficient (g ammonium sulfate cell^–1 h^–1) - m_(S) maintenance coefficient (g sugar g cell^–1 h^–1) - t time, h - Y yield coefficient (g cells/g ammonium sulfate) - Y_m maximum of Y - Y_S yield coefficient based on sugar consumed (g cells · g sugar^–1) - Y_S(m) maximum value of Y_S - ^µm maximum specific growth rate constant (h^–1)     

Modeling of the pyruvate production with<Emphasis Type="Italic"> Escherichia coli</Emphasis> in a fed-batch bioreactor

A family of 10 competing, unstructured models has been developed to model cell growth, substrate consumption, and product formation of the pyruvate producing strain Escherichia coli YYC202 ldhA::Kan strain used in fed-batch processes. The strain is completely blocked in its ability to convert pyruvate into acetyl-CoA or acetate (using glucose as the carbon source) resulting in an acetate auxotrophy during growth in glucose minimal medium. Parameter estimation was carried out using data from fed-batch fermentation performed at constant glucose feed rates of q_VG=10 mL h^–1. Acetate was fed according to the previously developed feeding strategy. While the model identification was realized by least-square fit, the model discrimination was based on the model selection criterion (MSC). The validation of model parameters was performed applying data from two different fed-batch experiments with glucose feed rate q_VG=20 and 30 mL h^–1, respectively. Consequently, the most suitable model was identified that reflected the pyruvate and biomass curves adequately by considering a pyruvate inhibited growth (Jerusalimsky approach) and pyruvate inhibited product formation (described by modified Luedeking–Piret/Levenspiel term).List of symbols c_A acetate concentration (g L^–1) - c_A,0 acetate concentration in the feed (g L^–1) - c_G glucose concentration (g L^–1) - c_G,0 glucose concentration in the feed (g L^–1) - c_P pyruvate concentration (g L^–1) - c_P,max critical pyruvate concentration above which reaction cannot proceed (g L^–1) - c_X biomass concentration (g L^–1) - K_I inhibition constant for pyruvate production (g L^–1) - K_I^A inhibition constant for biomass growth on acetate (g L^–1) - K_P saturation constant for pyruvate production (g L^–1) - K_P inhibition constant of Jerusalimsky (g L^–1) - K_S^A Monod growth constant for acetate (g L^–1) - K_S^G Monod growth constant for glucose (g L^–1) - m_A maintenance coefficient for growth on acetate (g g^–1 h^–1) - m_G maintenance coefficient for growth on glucose (g g^–1 h^–1) - n constant of extended Monod kinetics (Levenspiel) (–) - q_V volumetric flow rate (L h^–1) - q_VA volumetric flow rate of acetate (L h^–1) - q_VG volumetric flow rate of glucose (L h^–1) - r_A specific rate of acetate consumption (g g^–1 h^–1) - r_G specific rate of glucose consumption (g g^–1 h^–1) - r_P specific rate of pyruvate production (g g^–1 h^–1) - r_P,max maximum specific rate of pyruvate production (g g^–1 h^–1) - t time (h) - V reaction (broth) volume (L) - Y_P/G yield coefficient pyruvate from glucose (g g^–1) - Y_X/A yield coefficient biomass from acetate (g g^–1) - Y_X/A,max maximum yield coefficient biomass from acetate (g g^–1) - Y_X/G yield coefficient biomass from glucose (g g^–1) - Y_X/G,max maximum yield coefficient biomass from glucose (g g^–1) - growth associated product formation coefficient (g g^–1) - non-growth associated product formation coefficient (g g^–1 h^–1) - specific growth rate (h^–1) - _max maximum specific growth rate (h^–1)     

Effect of the dilution rate on the biomass yield ofBacillus thuringiensis and determination of its rate coefficients under steady-state conditions

Depending on the biomass yield on glucose and the cell morphology ofBacillus thuringiensis, three different metabolic states were observed in continuous culture. At dilution rates between 0.18 h^–1 and 0.31 h^–1 vegetative cells, sporulating bacteria and spores coexisted, while glucose and amino acids were consumed. Only vegetative cells were observed at dilution rates between 0.42 h^–1 and 0.47 h^–1 and glucose was used as the main carbon and energy source. AtD = 0.50 h^–1 the biomass yield on glucose decreases sharply. To define better the specific growth rate range in which the microorganism uses mainly glucose, a dilution rate of 0.25–0.45 h^–1 was studied. The experimental data could be adjusted to a Monod model and the following rate coefficients and growth yields were determined: maximum specific growth rate 0.54 h^–1, saturation constant 0.56 mg glucose ml^–1, biomass growth yields 0.43 g cells (g glucose)^–1, and 0.76 g cells (g oxygen)^–1, and maintenance coefficients 0.065 g glucose (g cells)^–1 h^–1 and 0.039 g oxygen (g cells)^–1 h^–1.     

Potential of Thiobacillus ferrooxidans for waste gas purification. Part 1. Kinetics of continuous ferrous iron oxidation

Kinetic data of ferrous iron oxidation by Thionacillus ferrooxidans were determined. The aim was to remove H₂S (<0.5 ppm) from waste gas by a process proposed earlier. Kinetic data necessary for industrial scale-up were investigated in a chemostat airlift reactor (dilution rate 0.02–0.12 h^–1; pH 1.3). Due to the low pH, ferric iron precipitation and wall growth could be avoided. The maximum ferrous iron oxidation rate of submersed bacteria was 0.77 g 1^–1 h^–1, the maximum specific growth rate about 0.12 h^–1 and the yield coefficient was found to be 0.007 g g^–1 Fe²⁺. The specific O₂ demand of an exponentially growing, ironoxidizing batch culture was 1.33 mg O₂ mg^–1 biomass h^–1. The results indicate that a pH of 1.3 has no negative influence on the kinetics of iron oxidation and growth. Correspondence to: W. Schäfer-Treffenfeldt     

Growth kinetic parameter estimation of Candida rugopelliculosa using a fish manufacturing effluent

A fourth order Runge–Kutta approximation was used to determine the Monod kinetics of Candida rugopelliculosa by using unsteady state data from only one continuous unsteady state operation at a fixed dilution rate. The maximum microbial growth rates, max, and half saturation coefficient, K _s, were 0.82 ± 0.22 h^–1 and 690 ± 220 mg soluble chemical oxygen demand (SCOD) l^–1, respectively. The microbial yield coefficient, Y, and microbial decay rate coefficient, k _d, were 1.39 ± 0.22 × 10⁴ cells mg^–1 SCOD and 0.06 ± 0.01 h^–1, respectively.     

The effect of carbon dioxide on the growth kinetics of fructose-limited chemostat cultures of Acetobacterium woodii DSM 1030

The growth of the anaerobic acetogenic bacterium Acetobacterium woodii DSM 1030 was investigated in fructose-limited chemostat cultures. A defined medium was developed which contained fructose, mineral salts, cysteine · HCl and Ca pantothenate (1 mg · 1^–1) supplied in a vitamin supplement. Growth at high dilution rates was dependent on the presence of CO₂ in the gas phase. The ^max was found to be 0.16 h^–1 and the fructose maintenance requirement was 0.1 to 0.13 mmol fructose · (g dry wt)^–1 · h^–1. A growth yield of 61 g dry wt · (mol fructose)^–1, corrected for the cell maintenance requirement and for incorporation of fructose carbon into cell biomass, was determined from the fructose consumption. A corresponding growth yield of 69 g dry wt · (mol fructose)^–1 was calculated from the acetate production assuming that fructose fermentation was homoacetogenic. A Y_ATP of 12.2 to 13.8 g dry wt · (mol ATP)^–1 was calculated from these growth yields using a value of 5 mol ATP · (mol fructose)^–1 as an estimate of the amount of ATP synthesised from fructose fermentation. The addition of yeast extract (0.5 g · 1^–1) to the medium did not influence the ^max or cell yield. After prolonged growth under fructose-limited conditions the requirement of the culture for CO₂ in the gas phase was reduced.Abbreviations YE yeast extract - IC inorganic carbon - D fermenter dilution rate : h^–1 - M_X maintenance requirement for X: mmol X · (g dry wt)^–1 · h^–1 - X may be fructose (Fruct), fructose consumed in energy metabolism (Fruct [E]), acetate (Ac) - ATP CO₂, NH _inf4 ^sup+ or Pi - qX specific rate of utilisation or consumption of X: mmol X · (g dry wt)^–1 · h^–1 - V fermenter volume: litre - rC · Cell, fermenter cell carbon production: mmol C · h^–1 - Y_X yield of cells on X: g dry wt · (mol X)^–1 - Y _infx ^supmax the yield corrected for cell maintenance: g dry wt · (mol X)^–1 - S_ATP stoichiometry of ATP synthesis from fructose: mol ATP · (mol frucose)^–1 - x cell concentration: g dry wt · 1^–1 - specific growth rate : h^–1 - ^max maximum specific growth rate: h^–1     

Microcalorimetric investigations of the metabolism of yeasts. Growth in chemostat cultures on glucose

Summary As part of a project on the production of penicillin, the penicillin production of two strains of Penicillium chrysogenum which have a different penicillin productivity was investigated in bubble column bioreactors and for comparison in stirred fermenters. The main interest of this study were the complicated interrelations between the stirrer speed, the stirrer type, the shear stress, the morphology of the mycelium and broth viscosity as well as the effect of the oxygen transfer behavior on antibiotic productivity.Stirred tank reactors with different turbine stirrers as well as with a draught tube and propeller were employed.The main variable investigated was the stirrer speed. At low stirrer speeds, gas dispersion is inadequate and the insufficient oxygen transfer rate is a limiting factor. At higher stirrer speeds, the oxygen supply of pulpy mycelia is improved and more cell mass is formed. This result is the same for both strains in all three reactors.If the oxygen partial pressure is near the lower cirtical value, a high percentage of the carbon source is converted into penicillin but the penicillin productivity is low due to a low percentage of penicillin producing cells. At oxygen partial pressures just above 8% saturation, the absolute penicillin productivity is maximal. At higher stirrer speeds and dissolved oxygen concentrations the penicillin production phase is shorter, cell growth is higher and a higher percentage of the carbon source is converted into CO₂.In reactors with a draught tube and propeller, a lower productivity is attained than in those with turbine stirrers.The behavior of the two strains is fairly similar. The higher producing strain, however, has a more distinct separation between its periods of growth and production than does the low producing one. At high stirrer speeds the increase in the cell growth rate is less significant and the substrate yield coefficients are higher for the high producing strain than for the low producing one.Symbols C Dissolved oxygen concentration (mg l^–1) - C^* C at saturation (mg l^–1) - k_La Volumetric mass transfer coefficient (h^–1) - OTR Oxygen transfer rate (mg l^–1 h^–1) - OUR Oxygen uptake rate (mg l^–1 h^–1) - rpm Impeller speed (min^–1) - X (Dry) biomass concentration (g kg^–1) - V_g Volumetric gas flow rate (Nl min^–1) - CMC Carboxymethyl cellulose     

Fed-batch fermentation for production of Kluyveromyces marxianusFII 510700 cultivated on a lactose-based medium

A strain of Kluyveromyces marxianus was grown in batch culture in lactose-based media at varying initial lactose concentrations (10–60 g L^–1) at 30°C, pH 5.0, dissolved oxygen concentrations greater than 20%. Increasing the concentration of mineral salts three-fold at 40 g L^–1 and 60 g L^–1 initial lactose concentration showed only a small increase in the yield of biomass, from 0.38 g g^–1 to 0.41 g g^–1, indicating that the initial batch cultures were not significantly nutrient- (mineral salts)-limited. A relatively high biomass concentration (105 g L^–1) was obtained in fed-batch culture following extended lactose feeding. An average specific growth rate (0.27 h^–1), biomass yield (0.38 g g^–1) and overall productivity (2.9 g L^–1 h^–1) were obtained for these fed-batch conditions. This fed-batch protocol provides a strategy for achieving relatively high concentrations and productivities of K. marxianus on other lactose-based substrate streams (e.g., whey) from the dairy industry.     

Decolourization of anaerobically digested and polyaluminium chloride treated distillery spentwash in a fungal stirred tank aerobic reactor

Decolourization of anaerobically digested and polyaluminium chloride treated distillery spentwash was studied in a fungal stirred tank aerobic reactor without dilution of wastewater. Aspergillus niger isolate IITB-V8 was used as the fungal inoculum. The main objectives of the study were to optimize the stirrer speed for achieving maximum decolourization and to determine the kinetic parameters. A mathematical model was developed to describe the batch culture kinetics. Volumetric oxygen transfer coefficient (k _L a) was obtained using dynamic method. The maximum specific growth rate and growth yield of fungus were determined using Logistic equation and using Luedeking–Piret equation. 150 rpm was found to be optimum stirrer speed for overall decolourization of 87%. At the optimum stirrer speed, volumetric oxygen transfer coefficient (k _L a) was 0.4957 min⁻¹ and the maximum specific growth rate of fungus was 0.224 h⁻¹. The values of yield coefficient (Y _x/s) and maintenance coefficient (m _s) were found to be 0.48 g cells (g substrate)⁻¹ and 0.015 g substrate (g cells)⁻¹ h⁻¹.     

Effect of dilution rate on the release of pertussis toxin and lipopolysaccharide ofBordetella pertussis

Summary The kinetics ofBordetella pertussis growth was studied in a glutamate-limited continuous culture. Growth kinetics corresponded to Monod's model. The saturation constant and maximum specific growth rate were estimated as well as the energetic parameters, theoretical yield of cells and maintenance coefficient. Release of pertussis toxin (PT) and lipopolysaccharide (LPS) were growth-associated. In addition, they showed a linear relationship between them. Growth rate affected neither outer membrane proteins nor the cell-bound LPS pattern.Nomenclature X cell concentration (g L^–1) - specific growth rate (h^–1) - _m maximum specific growth rate (h^–1) - D dilution rate (h^–1) - S concentration of growth rate-limiting nutrient (glutamate) (mmol L^–1 or g L^–1) - Ks substrate saturation constant (mol L^–1) - m_s maintenance coefficient (g g^–1 h^–1) - Y_x/s theoretical yield of cells from glutamate (g g^–1) - Y_x/s yield of cells from glutamate (g g^–1) - Y_PT/s yield of soluble PT from glutamate (mg g^–1) - Y_KDO/s yield of cell-free KDO from glutamate (g g^–1) - Y_PT/x specific yield of soluble PT (mg g^–1) - Y_KDO/x specific yield of cell-free KDO (g g^–1) - q_PT specific soluble PT production rate (mg g^–1 h^–1) - q_KDO specific cell-free KDO production rate (g g^–1 h^–1)     

Oxygen effect on batch cultures of Leuconostoc mesenteroides: relationship between oxygen uptake,growth and end-products

Growth and lactose metabolism of a Leuconostoc mesenteroides strain were studied in batch cultures at pH 6.5 and 30° C in 101 modified MRS medium sparged with different gases: nitrogen, air and pure oxygen. In all cases, growth occurred, but in aerobiosis there was oxygen consumption, leading to an improvement of growth yield Y _x/s and specific growth rate compared to anaerobiosis. Whatever the extent of aerobic growth, oxygen uptake and biomass production increased with the oxygen transfer rate so that the oxygen growth yield, Y _x/o2, remained at a constant value of 11 g dry weight of biomass/mol oxygen consumed. Pure oxygen had a positive effect on Leuconostoc growth. Oxygen transfer was limiting under air, but pure oxygen provided bacteria with sufficient dissolved oxygen and leuconostocs were able to consume large amounts of oxygen. Acetate production increased progressively with oxygen consumption so that the total molar concentration of acetate plus ethanol remained constant. Maximal Y _x/s was obtained with a 120 l/h flow rate of pure oxygen: the switch from ethanol to acetate was almost complete. In this case, a 46.8 g/mol Y _x/s and a 0.69 h^–1 maximal growth rate could be reached.     

Continuous cultivation of the yeast Candida utilis at different dilution rates on pineapple cannery effluent

Candida utilis was grown on a pineapple cannery effluent in a chemostat at dilution rates ranging between 0.05 and 0.65 h^–1 to establish optimal conditions for biomass production and chemical oxygen demand (COD) reduction. Sucrose, fructose and glucose were the main sugars in the effluent. Maximum value for cell yield coefficient and productivity were (0.686, g_x/g_s) and (2.96, g_x/l/h) at a dilution rate of 0.425 and 0.475 h^–1, respectively, while maximum COD reduction (98%) was attained at a dilution rate of 0.1 h^–1. The maintenance coefficient attained a value of (0.093, g_s/g_x/h). An increase in dilution rate produced a higher protein content of the biomass.     

A heuristic approach to fed-batch optimisation of streptokinase fermentation

Previous studies have shown that the rate of formation of streptokinase, a secondary metabolite, in batch fermentation is proportional to the specific growth rate of the biomass, which in turn is inhibited by its substrate and the primary product (lactic acid). These kinetics suggest the suitability of fed-batch operation to increase the yield of streptokinase. A near-optimal feed policy has been calculated by the chemotaxis algorithm, and it shows a substrate feed rate decreasing nonlinearly and vanishing after 11 hours. This is followed by batch fermentation for a further 8 hours, at the end of which 12% more streptokinase is generated than by purely batch fermentation. Further improvements in productivity are possible.List of Symbols k _dh^–1 decay constant for active cells - k _ph^–1 decay constant for streptokinase - K _Igl^–1 inhibition constant for lactic acid - K_S gl^–1 inhibition constant for substrate - M gl^–1 lactic acid concentration - P gl^–1 streptokinase concentration - Q 1h^–1 substrate feed rate - S gl^–1 substrate concentration - S _ingl^–1 inlet concentration of substrate - t h time - t _bh end-point of batch fermentation - t _fh end-point of fed-batch fermentation - V l volume of broth in fermenter - V ₀ l initial value of V (at t=0) - V _ml maximum value of V - X gl^–1 total biomass concentration - X _agl^–1 concentration of active biomass - Y _MX yield coefficient for lactic acid from biomass - Y _PX yield coefficient for streptokinase from biomass - Y _XS yield coefficient for biomass from substrate Greek Letters h^–1 specific growth rate of biomass - _mh^–1 maximum specific growth rate     

Conversion of fat into yeast biomass in protein-containing waste-water

Summary Candida tropicalis S001 was grown on the lipid fraction of a protein-containing waste-water in order to (i) remove fat from the water, and (ii) produre yeast biomass for feed. The yeast cells were separated from the waste-water by sedimentation. Defatted waste-water was used for methane production and gave a yield of a 0.3 m³ methane/kg reduced chemical oxygen demand. The maximum specific growth rate (µ_max) of C. tropicalis growing on waste-water fat at pH 4.0 was 0.35 h^–1; the fat content was decreased from 8 g/l to about 0.1 g/l within 24 h. In continous culture a corresponding reduction was maintained at dilution rates up to 0.36 h^–1. The effect on growth of pH, temperature and CO₂ concentration was studied with triolein as the major carbon source. The µ_max was nearly constant (0.16 h^–1) in the pH and temperature range of 3.2–4.0 and 30°–38° C, respectively; 10% CO₂ was optimal for growth. Growth on triolein resulted in a biomass yield of 0.70 g dry weight/g fat. Offprint requests to: S. Rydin     

Effects of growth temperature on maximal specific growth rate,yield, maintenance,and death rate in glucose-limited continuous culture of the thermophilic Bacillus caldotenax

Summary The influence of temperature on the growth of the theromophilic Bacillus caldotenax was investigated using chemostat techniques and a chemically defined minimal medium. All determined growth constants, that is maximal specific growth rate, yield and maintenance, were temperature dependent. It was striking that the very large maintenance requirement was about 10 times higher than for mesophilic cells under equivalent conditions. A death rate, which was very substantial at optimal and supraoptimal growth temperatures, was estimated by comparing the maintenance for substrate and oxygen. There was no indication for a thermoadaptation as postulated by Haberstich and Zuber (1974).Symbols D Dilution rate (h^–1) - D_c=_max Critical dilution rate (h^–1) - E Temperature characteristic (J mol^–1) - k Organism constant - k_d Death rate coefficient (h^–1) - k_m Maintenance substrate coefficient estimated from M_O (h^–1) - M_O Maintenance respiration, mmol O₂ per g dry biomass and h (mmol g^–1h^–1) - M_O Maintenance respiration, taking k_d into account - m_S Maintenance substrate coefficient, g glucose per g dry biomass and h (h^–1) - OD Optical density at 546 nm - QO₂ Specific O₂-uptake rate (mmol g^–1h^–1) - Q _O2 ^V Specific O₂-uptake rate for viable portion of biomass (mmol g^–1 h^–1) - Q_S Specific glucose uptake rate (h^–1) - Q _S ^V Specific glucose uptake rate for viable portion of biomass (h^–1) - R Gas constant 8.28 J mol^–1K^–1 - S Substrate concentration in reactor (g l^–1) - S_O Influent substrate concentration (g l^–1) - T_max Maximal growth temperature (°C) - T_min Minimal growth temperature (°C) - X Dry biomass (g l^–1) - X_tOt=X Dry biomass containing dead and viable cells - X_v Viable portion of biomass - Y _O ^m Potential yield for O₂ corrected for maintenance respiration (g mol^–1) - Y _S ^m Potential yield for substrate corrected for maintenance requirement, g biomass per g glucose (–) - Specific growth rate (h^–1) - _max Maximal specific growth rate (h^–1)     

Continuous culture of the hyperthermophilic archaeum Pyrococcus furiosus

Summary A system for continuous culture of the hyperthermophilic archaeum Pyrococcus furiosus in the absence of elemental sulphur has been developed. An all-glass gas-lift bioreactor was used to provide high mass transfer at low shear forces, whilst eliminating the potential for corrosion. Steady-state cell densities of P. furiosus were found to increase with higher inert gas flow rates, reaching a maximum in this system with 0.5 vol. vol^–1 min^–1 of nitrogen (N₂). N₂ permitted higher cell densities than the other inert gases tested (argon, helium and sulphur hexafluoride) under equivalent conditions. At 0.5 vol. vol^–1 min^–1 of N₂ a cell density in excess of 3 × 10⁹ ml^–1 could be maintained indefinitely at a dilution rate of 0.2 h^–1. Higher dilution rates gave progressively lower steady-state cell densities. Teh biomass production was maximal, however, at a dilution rate of 0.4 h^–1. At this dilution rate the bioreactor was able to generate more than 1.5 g wet weight of cells h^–1 l^–1 culture volume.Correspondence to: N. Raven     

Cellulase production by Trichoderma reesei (RUT-C30) in fed-batch culture

Summary Fed-batch cultures of Trichoderma reesei RUT-C30 attained quasi-steady state conditions, in respect of biomass concentration and enzyme production rate, commensurate with a specific cell maintenance coefficient of 0.029 g cellulose.g biomass.^–1h^–1 and specific cellulase production rate of between 9.6 and 11.9 IU (filter paper activity).g biomass.^–1h^–1. A maximum enzyme yield of 57 IU.m1^–1 at an overall productivity of 201 IU.L.^–1h^–1 resulted from a cellulose feed rate of 1.0g.L.^–1h^–1.