Lead removal by Spirulina platensis biomass

In this investigation, we report on the biosorption of Pb (II) from aqueous solutions by the nonliving biomass of the micro-alga (cyanobacterium) Spirulina platensis. Propagation of the micro-alga was carried out in outside oblong raceway ponds. The biomass was cleaned, dried and used for the investigation. The effects of pH, adsorbent dose, temperature, initial concentration of Pb (II), and contact time on the adsorption of lead by the dry biomass were studied. The experiments were carried out in 250 ml conical flasks containing 100 ml of test solutions using an orbital incubator at 150 rpm. Concentrations of the metal before and after the experiments were measured using Atomic Absorption Spectrophotometer. Very high levels of Pb (II) removal (>91%) were obtained. The optimum conditions for maximal adsorption by S. platensis were found to be pH 3; 2 g of adsorbent dose; incubation at 26°C; 100 mg/l of lead initial concentration and 60 minutes of contact time. The experimental data fitted well with Freundlich isotherm equation with R² values greater than 0.97. Based on our results, we recommend the utilization of S. platensis biomass for heavy metal removal from aqueous solutions.     

Application of Arthrospira (Spirulina) platensis biomass for silver removal from aqueous solutions

The cyanobacterium Arthrospira (Spirulina) platensis was used to study the process of silver biosorption. Effects of various parameters such as contact time, dosage of biosorbent, initial pH, temperature, and initial concentration of Ag(I) were investigated for a batch adsorption system. The optimal biosorption conditions were determined as pH 5.0, biosorbent dosage of 0.4 g, and initial silver concentration of 30 mg/L. Equilibrium adsorption data were analyzed by the Langmuir and Freundlich models – however, the Freundlich model provided a better fit to the experimental data. The kinetic data fit the pseudo-second-order model well, with a correlation coefficient of 0.99. The analysis of thermodynamic parameters (ΔG°, ΔH° and ΔS°) revealed that the adsorption process of silver ion by spirulina biomass was exothermic and spontaneous (ΔG° < 0), and exothermic (ΔH° < 0) process. The biosorption capacity of biomass A. platensis serves as a basis for the development of green technology for environmental remediation.     

Application of Freundlich and Langmuir models to multistage purification process to remove heavy metal ions by using Schizomeris leibleinii

The adsorption of iron(III), lead(II) and cadmium(II) ions onto Schizomeris leibleinii, a green alga, was studied with respect to initial pH, temperature, initial metal ion and biomass concentration to determine the optimum adsorption conditions. Optimum initial pH for iron(III), lead(II) and cadmium(II) ions were 2.5, 4.5 and 5.0 at optimum temperature 30°C, respectively. The initial adsorption rates increased with increasing initial iron(III), lead(II) and cadmium(II) ion concentrations up to 100, 100 and 150 mg l⁻¹, respectively. The Freundlich and Langmuir adsorption isotherms were developed at various initial pH and temperature values. The adsorption of these metal ions to S. leibleinii was investigated in a two-stage mixed batch reactor. The residual metal ion concentrations (C_eq) at equilibrium at each stage for a given ‘quantity of dried algae (X₀)/volume of solution containing heavy metal ion (V₀)’ ratio were calculated using Freundlich and Langmuir isotherm constants. The experimental biosorption equilibrium data for iron(III), lead(II) and cadmium(II) ions were in good agreement with those calculated by both Freundlich and Langmuir models. The adsorbed iron(III), lead(II) and cadmium(II) ion concentrations increased with increasing X₀/V₀ ratios while the adsorbed metal quantities per unit mass of dried algae decreased.     

Immobilization of <Emphasis Type="Italic">Pseudomonas putida</Emphasis> PT in resistant matrices to environmental stresses: a strategy for continuous removal of heavy metals under extreme conditions

The purpose of this study was to investigate the potential of immobilized lead- and cadmium-resistant Pseudomonas putida strain PT to remove heavy metals from aqueous medium under extreme conditions. The tolerance and accumulation of cadmium and lead ions by strain PT were investigated by minimal inhibitory concentration (MIC) determination and polymerase chain reaction (PCR) of cadA gene, respectively. The surface chemical functional groups of P. putida PT involved in the metal biosorption were identified by Fourier transform infrared (FTIR). Pseudomonas putida PT was immobilized in three matrices include carboxy-methyl cellulose (CMC), rice bran, and a new composite made of alginate, polyvinyl alcohol (PVA), and CaCO₃ to prepare heavy metal adsorbent. The biosorbents were analyzed by SEM, and their metal removal capability was assayed in two consecutive cycles by atomic absorption spectroscopy. The viability of immobilized bacterial cells was determined by flow cytometry during storage at 4 °C and exposure to the environmental stresses (pH and temperature). The results showed that PT strain was resistant up to 10 mM Pb²⁺ and 8 mM Cd²⁺. FTIR analysis revealed that alcohol, sulfur, phosphate, esters, and amide groups played important roles in metal biosorption process and, also change in metabolic reactions like hydration and polyesters accumulation was observed after metal biosorption. The presence of cadA gene, a heavy metal translocating pump-coding gene, indicated the ability of metals bioaccumulation by the PT strain. Immobilized cells in alginate–PVA–CaCO₃ and rice bran showed the highest metal removal efficiency for Pb²⁺ as 75% and Cd²⁺ as 96.7%, respectively. Metal adsorbents were reusable, and the highest removal efficiency in the second cycle was observed in inoculated alginate–PVA–CaCO₃ (79.5% Pb²⁺ and 45% Cd²⁺). Flow cytometric analysis represented that the immobilized cell viability was retained (<?97%) after 4 weeks storage at 4 °C. Viability under two environmental stresses in all matrices was as follows: <?96% at 25 °C, <?87% at 45 °C, <?85% at pH 4,?<?96% at pH 7, and?<?89% at pH 11. The results signify that these metal adsorbents are efficient technological tools for bioremediation even in harsh environmental conditions.     

Biosorption of Chromium(VI) and Lead(II): Role of Spirulina platensis in the Treatment of Industrial Effluent

Biosorption is the process of removal of any chemical molecules by the treatment of biological material. Industrialization resulted in the discharge of various toxic heavy metals into water bodies, which poses serious health hazards to humans and animals. In the present study, live Spirulina platensis was used as a biosorbent for the removal of the heavy metals chromium (Cr(VI)) and lead (Pb(II)) from the aqueous samples. S. platensis were cultured in the presence of different concentrations of heavy metals. The growth of the algal cells was found to be decreased by 59% and 36% in media containing 50 ppm Cr(VI) and Pb(II), respectively. To assess the biosorption of heavy metals, at different time intervals, the spent culture media were used to detect Cr(VI) by atomic absorption spectroscopy method and Pb(II) by 4-(2-pyridylazo)resorcinol indicator method. Results suggested that there was a significant uptake of Cr(VI) and Pb(II) from the medium by S. platensis, with corresponding decrease of metals in the medium. When metal salt solutions or industrial effluent samples were passed through the column containing immobilized live S. platensis in calcium alginate beads, the concentration of Cr(VI) was found to be reduced drastically. The present study indicates the application of S. platensis for the bioremediation of heavy metals from the samples obtained from industrial effluents.     

Thermostable phycocyanin from the red microalga <Emphasis Type="Italic">Cyanidioschyzon merolae</Emphasis>, a new natural blue food colorant

The demand for natural food colorants is growing as consumers question the use of artificial colorants more and more. The phycobiliprotein C-phycocyanin of Arthospira platensis is used as a natural blue colorant in certain food products. The thermoacidophilic red microalga Cyanidioschyzon merolae might provide an alternative source of phycocyanin. Cyanidioschyzon merolae belongs to the order Cyanidiophyceae of the phylum Rhodophyta. Its natural habitat are sulfuric hot springs and geysers found near volcanic areas in, e.g., Yellowstone National Park in the USA and in Java, Indonesia. It grows optimally at a pH between 0.5 and 3.0 and at temperatures up to 56 °C. The low pH at which C. merolae grows minimizes the risk of microbial contamination and could limit production loss. As C. merolae lacks a cell wall, phycocyanin with a high purity number of 9.9 could be extracted by an osmotic shock using a simple ultrapure water extraction followed by centrifugation. The denaturation midpoint at pH 5 was 83 °C, being considerably higher than the A. platensis phycocyanin (65 °C). The C. merolae phycocyanin was relatively stable at pH 4 and 5 up to 80 °C. The high thermostability at slightly acidic pH makes the C. merolae phycocyanin an interesting alternative to A. platensis phycocyanin as a natural blue food colorant.     

Kinetic,thermodynamic, and equilibrium biosorption of Pb(II), Cu(II), and Ni(II) using dead mushroom biomass under batch experiment

In this study, a low-cost biosorbent, dead mushroom biomass (DMB) granules, was used for investigating the optimum conditions of Pb(II), Cu(II), and Ni(II) biosorption from aqueous solutions. Various physicochemical parameters, such as initial metal ion concentration, equilibrium time, pH value, agitation speed, particles diameter, and adsorbent dosage, were studied. Five mathematical models describing the biosorption equilibrium and isotherm constants were tested to find the maximum uptake capacities: Langmuir, Freundlich, Redlich-Peterson, Sips, and Khan models. The best fit to the Pb(II) and Ni(II) biosorption results was obtained by Langmuir model with maximum uptake capacities of 44.67 and 29.17 mg/g for these two ions, respectively, whereas for Cu(II), the corresponding value was 31.65 mg/g obtained with Khan model. The kinetic study demonstrated that the optimum agitation speed was 400 rpm, at which the best removal efficiency and/or minimum surface mass transfer resistance (MSMTR) was achieved. A pseudo-second-order rate kinetic model gave the best fit to the experimental data (R² = 0.99), resulting in MSMTR values of 4.69× 10^?5, 4.45× 10^?6, and 1.12× 10^?6 m/s for Pb(II), Cu(II), and Ni(II), respectively. The thermodynamic study showed that the biosorption process was spontaneous and exothermic in nature.     

Fibrous polymer-grafted chitosan/clay composite beads as a carrier for immobilization of papain and its usability for mercury elimination

Papain, which is an industrially important enzyme, has been immobilized on fibrous polymer-modified composite beads, namely poly(methacrylic acid)-grafted chitosan/clay. Characterization studies have been done using FTIR and SEM analysis. Operating parameters such as pH and initial concentration of papain have been varied to obtain the finest papain immobilized polymer-modified composite beads. The immobilization capacity of composite beads has been determined as 34.47 ± 1.18 (n = 3) mg/g. The proteolytic activity of immobilized papain was operated using bovine serum albumin (BSA) and maximum velocity (V _max) and Michaelis–Menten constant (K_m) values of the free and immobilized enzymes were determined using Lineweaver–Burk and Eadie–Hofstee equations. Usability of papain immobilized polymer-modified composite beads as adsorbents for the elimination of mercury was investigated. The maximum removal capacity of PIPMC beads has been found to be 4.88 ± 0.21 mg Hg/g when the initial metal concentration and weight of polymer-modified composite beads were 50 mg/L and 0.04 g at pH 7, respectively. Mercury removal performance of the papain immobilized polymer-modified composite beads was investigated in conjunction with Cu (II), Zn (II) and Cd (II) ions. The mercury adsorption capacity of papain immobilized polymer-modified composite beads was a slight reduction from 1.15 to 0.89 mg/g in presence of multiple metal salts.     

A comparative study on heavy metal biosorption characteristics of some algae

The biosorption of copper(II), nickel(II) and chromium(VI) from aqueous solutions on dried (Chlorella vulgaris, Scenedesmus obliquus and Synechocystis sp.) algae were tested under laboratory conditions as a function of pH, initial metal ion and biomass concentrations. Optimum adsorption pH values of copper(II), nickel(II) and chromium(VI) were determined as 5.0, 4.5 and 2.0. respectively, for all three algae. At the optimal conditions, metal ion uptake increased with initial metal ion concentration up to 250 mg l⁻¹. Experimental results also showed the influence of the alga concentration on the metal uptake for all the species. Both the Freundlich and Langmuir adsorption models were suitable for describing the short-term biosorption of copper(II), nickel(II) and chromium(VI) by all the algal species.     

Cobalt separation by <Emphasis Type="Italic">Alphaproteobacterium</Emphasis> MTB-KTN90: magnetotactic bacteria in bioremediation

Bioremediation of toxic metals by magnetotactic bacteria and magnetic separation of metal-loaded magnetotactic bacteria are of great interest. This bioprocess technique is rapid, efficient, economical, and environmentally friendly. In this study, cobalt removal potential of a novel isolated magnetotactic bacterium (Alphaproteobacterium MTB-KTN90) as a new biosorbent was investigated. The effects of various environmental parameters in the cobalt removal and the technique of magnetic separation of cobalt-loaded bacterial cells were studied. Cobalt removal by MTB-KTN90 was very sensitive to pH solution; higher biosorption capacity was observed around pH 6.5–7.0. When biomass concentration increased from 0.009 to 0.09 g/l, the biosorption efficiency increased from 13.87 % to 19.22 %. The sorption of cobalt by MTB-KTN90 was rapid during the first 15 min (859.17 mg/g dry weight). With the increasing of cobalt concentrations from 1 to 225 mg/l, the specific cobalt uptake increased. Maximum cobalt removal (1160.51 ± 15.42 mg/g dry weight) took place at optimum conditions; pH 7.0 with initial cobalt concentration of 115 mg/l at 60 min by 0.015 g/l of dry biomass. The results showed maximum values for constants of Langmuir and Freundlich models so far. The biosorption mechanisms were studied with FTIR, PIXE, and FESEM analysis. Cobalt-loaded MTB-KTN90 had ability to separate from solution by a simple magnetic separator. Magnetic response in MTB-KTN90 is due to the presence of unique intracellular magnetic nanoparticles (magnetosomes). The orientation magnetic separation results indicated that 88.55 % of cobalt was removed from solution. Consequently, Alphaproteobacterium MTB-KTN90 as a new biosorbent opens up good opportunities for the magnetic removal of cobalt from the polluted aquatic environments.     

Arthrospira (Spirulina) platensis: An effective biosorbent for nutrients

Arthrospira (Spirulina) platensis was tested for biosorption properties. Preliminary experiments concerning biosorption kinetics were performed on Cr(III) ions. Equilibrium of biosorption was tested for Cr(III), Mn(II) and Mg(II) ions, since these elements are crucial for animals with metabolic disorders. In our study, Spirulina was proposed as a feed additive for animals suffering from diseases characterized by insulin dysregulation, abnormal adipose distribution and a high risk for laminitis. Maximum biosorption capacity of A. platensis, determined from Langmuir equation, was 45.2 for Cr(III), 44.3 for Mn(II) and 42.0 mg/g for Mg(II) ions. Biosorption of Mg(II) ions by microalga has never been studied so far. Finally, the raw and enriched microalgal biomass was examined by ICP-OES to determine its multielamental analysis before and after biosorption, FTIR to indicate functional groups that participated in biosorption and SEM-EDX to illustrate the binding of metal ions on the surface of algal biomass. ICP-OES showed that the content of elements significantly increased in the enriched A. platensis. FTIR spectroscopy evidenced that biosorption of metal ions was mainly due to carboxylate groups present on the microalgal cell wall. SEM analysis clearly showed that biosorption occurred. Arthrospira platensis turned out to be a good biosorbent of metal ions.     

Inactivation of the transcription factor <Emphasis Type="Italic">mig1</Emphasis> (<Emphasis Type="Italic">YGL035C</Emphasis>) in <Emphasis Type="Italic">Saccharomyces cerevisiae</Emphasis> improves tolerance towards monocarboxylic weak acids: acetic,formic and levulinic acid

Toxic concentrations of monocarboxylic weak acids present in lignocellulosic hydrolyzates affect cell integrity and fermentative performance of Saccharomyces cerevisiae. In this work, we report the deletion of the general catabolite repressor Mig1p as a strategy to improve the tolerance of S. cerevisiae towards inhibitory concentrations of acetic, formic or levulinic acid. In contrast with the wt yeast, where the growth and ethanol production were ceased in presence of acetic acid 5 g/L or formic acid 1.75 g/L (initial pH not adjusted), the m9 strain (Δmig1::kan) produced 4.06?±?0.14 and 3.87?±?0.06 g/L of ethanol, respectively. Also, m9 strain tolerated a higher concentration of 12.5 g/L acetic acid (initial pH adjusted to 4.5) without affecting its fermentative performance. Moreover, m9 strain produced 33% less acetic acid and 50–70% less glycerol in presence of weak acids, and consumed acetate and formate as carbon sources under aerobic conditions. Our results show that the deletion of Mig1p provides a single gene deletion target for improving the acid tolerance of yeast strains significantly.     

Rapid bioremediation of Alizarin Red S and Quinizarine Green SS dyes using <Emphasis Type="Italic">Trichoderma lixii</Emphasis> F21 mediated by biosorption and enzymatic processes

In this study, a newly isolated ascomycete fungus Trichoderma lixii F21 was explored to bioremediate the polar [Alizarin Red S (ARS)] and non-polar [Quinizarine Green SS (QGSS)] anthraquinone dyes. The bioremediation of ARS and QGSS by T. lixii F21 was found to be 77.78 and 98.31 %, respectively, via biosorption and enzymatic processes within 7 days of incubation. The maximum biosorption (ARS = 33.7 % and QGSS = 74.7 %) and enzymatic biodegradation (ARS = 44.1 % and QGSS = 23.6 %) were observed at pH 4 and 27 °C in the presence of glucose and yeast extract. The laccase and catechol 1,2-dioxygenase produced by T. lixii F21 were involved in the molecular conversions of ARS and QGSS to phenolic and carboxylic acid compounds, without the formation of toxic aromatic amines. This study suggests that T. lixii F21 may be a good candidate for the bioremediation of industrial effluents contaminated with anthraquinone dyes.     

Biosorption of lead phosphates by lead-tolerant bacteria as a mechanism for lead immobilization

The study of metal-tolerant bacteria is important for bioremediation of contaminated environments and development of green technologies for material synthesis due to their potential to transform toxic metal ions into less toxic compounds by mechanisms such as reduction, oxidation and/or sequestration. In this study, we report the isolation of seven lead-tolerant bacteria from a metal-contaminated site at Zacatecas, México. The bacteria were identified as members of the Staphylococcus and Bacillus genera by microscopic, biochemical and 16S rDNA analyses. Minimal inhibitory concentration of these isolates was established between 4.5 and 7.0 mM of Pb(NO₃)₂ in solid and 1.0–4.0 mM of Pb(NO₃)₂ in liquid media. A quantitative analysis of the lead associated to bacterial biomass in growing cultures, revealed that the percentage of lead associated to biomass was between 1 and 37% in the PbT isolates. A mechanism of complexation/biosorption of lead ions as inorganic phosphates (lead hydroxyapatite and pyromorphite) in bacterial biomass, was determined by Fourier transform infrared spectroscopy and X-ray diffraction analyses. Thus, the ability of the lead-tolerant isolates to transform lead ions into stable and highly insoluble lead minerals make them potentially useful for immobilization of lead in mining waste.     

Interaction of Mercuric Ions with Different Marine Algal Species

The use of different seaweeds such as Sargassum sp., Turbinaria conoides, and Ulva sp. in removing mercury(II) from aqueous solutions were investigated. The initial experimental runs, conducted at different equilibrium pH conditions, demonstrated that brown seaweeds outperformed green seaweed in Hg(II) biosorption at all pH conditions. In particular, at pH 5, maximum biosorption capacities of 170.3 and 145.8 mg/g were recorded for the brown seaweeds T. conoides and Sargassum sp., respectively, compared with 138.4 mg/g for the green seaweed Ulva sp. Isotherm data were modeled and interpreted using the Langmuir, Freundlich, Redlich-Peterson, and Toth models, with the latter described the Hg(II) isotherms with high correlation coefficients and low % error values. The kinetic data indicate the rapidity of the biosorption process, with the equilibrium achieved within 90 min. Several models, including the Elovich, pseudo-first-order, and pseudo-second-order models, were examined for their suitability with the present data; the correlation coefficient and % error values, along with better prediction of equilibrium uptake values, favored the pseudo-first-order model. The desorption experiments were highly successful for T. conoides biomass with 0.05 M HCl, whereas for the other two seaweeds, 0.05 M HCl resulted in high biomass weight loss. Reusing T. conoides biomass in three successive sorption-desorption cycles resulted in only 8.8% reduction in Hg(II) biosorption capacity compared with its original uptake.     

Biosorption characteristics of Aspergillus flavus biomass for removal of Pb(II) and Cu(II) ions from an aqueous solution

The Pb(II) and Cu(II) biosorption characteristics of Aspergillus flavus fungal biomass were examined as a function of initial pH, contact time and initial metal ion concentration. Heat inactivated (killed) biomass was used in the determination of optimum conditions before investigating the performance of pretreated biosorbent. The maximum biosorption values were found to be 13.46 +/- 0.99 mg/g for Pb(II) and 10.82 +/- 1.46 mg/g for Cu(II) at pH 5.0 +/- 0.1 with an equilibrium time of 2 h. Detergent, sodium hydroxide and dimethyl sulfoxide pretreatments enhanced the biosorption capacity of biomass in comparison with the heat inactivated biomass. The biosorption data obtained under the optimum conditions were well described by the Freundlich isotherm model. Competitive biosorption of Pb(II) and Cu(II) ions was also investigated to determine the selectivity of the biomass. The results indicated that A. flavus is a suitable biosorbent for the removal of Pb(II) and Cu(II) ions from aqueous solution.     

Date stones of Phoenix dactylifera and jujube shells of Ziziphus lotus as potential biosorbents for anionic dye removal

This study investigated the biosorption of Congo Red (CR) from aqueous solution by Date stones (DS) of Phoenix dactylifera and jujube shells (JS) of Ziziphus lotus. Batch operations were carried out in the liquid phase to observe the effect of various experimental parameters such as contact time, pH, temperature, and initial dye concentration on removal of CR. The characteristics of the DS and JS were also examined by Fourier transform infrared analysis. The biosorption data of CR on DS and JS samples were well fitted with the Langmuir isotherm and pseudo-second kinetics model with a maximum biosorption amount of 45.08 mg g^?1 for DS and 59.55 mg g^?1 for JS at pH = 4, temperature of 50°C, and an initial concentration of 100–800 mg L^?1 after 90 minutes of contact time. The outcomes indicated that DS and JS can be used as a good low-cost alternative for the treatment of effluents containing CR in water.     

Heterologous expression and characterization of a new heme-catalase in <Emphasis Type="Italic">Bacillus subtilis</Emphasis> 168

Reactive oxygen species (ROS) is an inherent consequence to all aerobically living organisms that might lead to the cells being lethal and susceptible to oxidative stress. Bacillus pumilus is characterized by high-resistance oxidative stress that stimulated our interest to investigate the heterologous expression and characterization of heme-catalase as potential biocatalyst. Results indicated that recombinant enzyme significantly exhibited the high catalytic activity of 55,784 U/mg expressed in Bacillus subtilis 168 and 98.097 µmol/min/mg peroxidatic activity, the apparent K _m of catalytic activity was 59.6 ± 13 mM with higher turnover rate (K _cat = 322.651 × 10³ s^?1). The pH dependence of catalatic and peroxidatic activity was pH 7.0 and pH 4.5 respectively with temperature dependence of 40 °C and the recombinant heme-catalase exhibited a strong Fe²⁺ preference. It was further revealed that catalase KatX2 improved the resistance oxidative stress of B. subtilis. These findings suggest that this B. pumilus heme-catalase can be considered among the industrially relevant biocatalysts due to its exceptional catalytic rate and high stability and it can be a potential candidate for the improvement of oxidative resistance of industrially produced strains.     

The nitrite reductase activity of horse heart carboxymethylated-cytochrome <Emphasis Type="Italic">c</Emphasis> is modulated by cardiolipin

Horse heart carboxymethylated cytc (CM-cytc) displays myoglobin-like properties. Here, the effect of cardiolipin (CL) liposomes on the nitrite reductase activity of ferrous CM-cytc [CM-cytc-Fe(II)], in the presence of sodium dithionite, is reported between pH 5.5 and 7.6, at 20.0 °C. Cytc-Fe(II) displays a very low value of the apparent second-order rate constant for the NO₂ ^?-mediated conversion of cytc-Fe(II) to cytc-Fe(II)-NO [k _on = (7.3 ± 0.7) × 10^?2 M^?1 s^?1; at pH 7.4], whereas the value of k _on for NO₂ ^? reduction by CM-cytc-Fe(II) is 1.1 ± 0.2 M^?1 s^?1 (at pH 7.4). CL facilitates the NO₂ ^?-mediated nitrosylation of CM-cytc-Fe(II) in a dose-dependent manner, the value of k _on for the NO₂ ^?-mediated conversion of CL–CM-cytc-Fe(II) to CL–CM-cytc-Fe(II)-NO (5.6 ± 0.6 M^?1 s^?1; at pH 7.4) being slightly higher than that for the NO₂ ^?-mediated conversion of CL–cytc-Fe(II) to CL–cytc-Fe(II)-NO (2.6 ± 0.3 M^?1 s^?1; at pH 7.4). The apparent affinity of CL for CM-cytc-Fe(II) is essentially pH independent, the average value of B being (1.3 ± 0.3) × 10^?6 M. In the absence and presence of CL liposomes, the nitrite reductase activity of CM-cytc-Fe(II) increases linearly on lowering pH and the values of the slope of the linear fittings of Log k _on versus pH are ?1.05 ± 0.07 and ?1.03 ± 0.03, respectively, reflecting the involvement of one proton for the formation of the transient ferric form, NO, and OH^?. These results indicate that Met80 carboxymethylation and CL binding cooperate in the stabilization of the highly reactive heme-Fe atom of CL–CM-cytc.     

Efficient bioconversion of <Emphasis Type="SmallCaps">l</Emphasis>-glutamate to γ-aminobutyric acid by <Emphasis Type="Italic">Lactobacillus brevis</Emphasis> resting cells

This work investigated the efficient bioconversion process of l-glutamate to GABA by Lactobacillus brevis TCCC 13007 resting cells. The optimal bioconversion system was composed of 50 g/L 48 h cultivated wet resting cells, 0.1 mM pyridoxal phosphate in glutamate-containing 0.6 M citrate buffer (pH 4.5) and performed at 45 °C and 180 rpm. By 10 h bioconversion at the ratio of 80 g/L l-glutamic acid to 240 g/L monosodium glutamate, the final titer of GABA reached 201.18 g/L at the molar bioconversion ratio of 99.4 %. This process presents a potential for industrial and commercial applications and also offers a promising feasibility of continuous GABA production coupled with fermentation. Besides, the built kinetics model revealed that the optimum operating conditions were 45 °C and pH 4.5, and the bioconversion kinetics at low ranges of substrate concentration (0 < S < 80 g/L) was assumed to follow the classical Michaelis–Menten equation.