Enhanced enzymatic hydrolysis of wheat straw by aqueous glycerol pretreatment

Considering the practical technology-economy of glycerol processing from oleochemicals industry, the ensuing work was proposed to further explore the atmospheric aqueous glycerol autocatalytic organosolv pretreatment (AAGAOP) to improve the enzymatic hydrolysis of lignocellulosic biomass. With the liquid-solid ratio of 20 g g(-1) at 220 degrees C for 3h, the AAGAOP enabled wheat straw to remove approximately 70% hemicelluloses and approximately 65% lignin, with approximately 98% cellulose retention. The pretreated fiber was achieved with approximately 90% of the enzymatic hydrolysis yield after 48 h. At oven-drying, dehydration was likely to cause the hornification of fiber, which was responsible for the low enzymatic hydrolysis of dried fiber. With SEM observations, the AAGAOP disrupted wheat straw into thin and fine fibrils, with a small average size and more surface area. The AAGAOP technique, as a novel strategy, enhanced the enzymatic hydrolysis of lignocellulosic biomass by removing the chemically compositional barrier and altering the physically structural impediment.     

Effect of hydrogen peroxide pretreatment on the structural features and the enzymatic hydrolysis of rice straw

Assessment was made to evaluate the effect of hydrogen peroxide pretreatment on the change of the structural features and the enzymatic hydrolysis of rice straw. Changes in the lignin content, weight loss, accessibility for Cadoxen, water holding capacity, and crystallinity of straw were measured during pretreatment to express the modification of the lignocellulosic structure of straw. The rates and the extents of enzymatic hydrolysis, cellulase adsorption, and cellobiose accumulation in the initial stage of hydrolysis were determined to study the pretreatment effect on hydrolysis. Pretreatment at 60 degrees C for 5 h in a solution with 1% (w/w) H(2)O(2) and NaOH resulted in 60% delignification, 40% weight loss, a fivefold increase in the accessibility for Cadoxen, an one times increase in the water-holding capacity, and only a slight decrease in crystallinity as compared with that of the untreated straw. Improvement on the pretreatment effect could be made by increasing the initial alkalinity and the pretreatment temperature of hydrogen peroxide solution. A saturated improvement on the structural features was found when the weight ratio of hydrogen peroxide to straw was above 0.25 g H(2)O(2)/g straw in an alkaline H(2)O(2) solution with 1% (w/w) NaOH at 32 degrees C. The initial rates and extents of hydrolysis, cellulase adsorption, and cellobiose accumulation in hydrolysis were enhanced in accordance with the improved structural features of straw pretreated. A four times increase in the extent of the enzymatic hydrolysis of straw for 24 h was attributed to the alkaline hydrogen peroxide pretreatment.     

Pretreatment and Lignocellulosic Chemistry

Lignocellulosic materials such as wood, grass, and agricultural and forest residues are promising alternative energy resources that can be utilized to produce ethanol. The yield of ethanol production from native lignocellulosic material is relatively low due to its native recalcitrance, which is attributed to, in part, lignin content/structure, hemicelluloses, cellulose crystallinity, and other factors. Pretreatment of lignocellulosic materials is required to overcome this recalcitrance. The goal of pretreatment is to alter the physical features and chemical composition/structure of lignocellulosic materials, thus making cellulose more accessible to enzymatic hydrolysis for sugar conversion. Various pretreatment technologies to reduce recalcitrance and to increase sugar yield have been developed during the past two decades. This review examines the changes in lignocellulosic structure primarily in cellulose and hemicellulose during the most commonly applied pretreatment technologies including dilute acid pretreatment, hydrothermal pretreatment, and alkaline pretreatment.     

Reconstruction of lignin and hemicelluloses by aqueous ethanol anti‐solvents to improve the ionic liquid‐acid pretreatment performance of Arundo donax Linn

Ionic liquid (IL)‐acid pretreatment is known to not only enhance the enzymatic hydrolysis efficiency of lignocellulose but also to generate deposits on the surface of fiber by conventional water regeneration, which retard the increment. In this study, ethanol aqueous solution regeneration was developed as a new method to change the substrates characteristics for IL‐acid pretreatment and their effects on the enzymatic hydrolysis were evaluated. Following the IL‐acid reaction, the biomass slurry was subjected to ethanol aqueous solution at various concentration. Results indicated that anti‐solvent choice significantly influenced the reconstruction of both hemicelluloses and lignin as a result of the competition between water and ethanol. The partial removal of hemicelluloses and suitable lignin re‐localization contributed to a more porous structure. Consequently, the cellulose digestibility of aqueous ethanol regenerated samples was dramatically enhanced to ～100% and approximately 11‐ and 2‐fold higher than that of untreated and conventional water regenerated pretreated samples, respectively. A giant leap in the initial rate of enzymatic hydrolysis was also detected in 50% ethanol aqueous solution regenerated samples and only about 10 hr was needed to convert 80% of cellulose to glucose due to the appearance of cellulose II hydrate‐like and more porous structure.     

Hemicelluloses negatively affect lignocellulose crystallinity for high biomass digestibility under NaOH and H2SO4 pretreatments in Miscanthus

ABSTRACT: BACKGROUND: Lignocellulose is the most abundant biomass on earth. However, biomass recalcitrance has become a major factor affecting biofuel production. Although cellulose crystallinity significantly influences biomass saccharification, little is known about the impact of three major wall polymers on cellulose crystallization. In this study, we selected six typical pairs of Miscanthus samples that presented different cell wall compositions, and then compared their cellulose crystallinity and biomass digestibility after various chemical pretreatments. RESULTS: A Miscanthus sample with a high hemicelluloses level was determined to have a relatively low cellulose crystallinity index (CrI) and enhanced biomass digestibility at similar rates after pretreatments of NaOH and H2SO4 with three concentrations. By contrast, a Miscanthus sample with a high cellulose or lignin level showed increased CrI and low biomass saccharification, particularly after H2SO4 pretreatment. Correlation analysis revealed that the cellulose CrI negatively affected biomass digestion. Increased hemicelluloses level by 25% or decreased cellulose and lignin contents by 31% and 37% were also found to result in increased hexose yields by 1.3-times to 2.2-times released from enzymatic hydrolysis after NaOH or H2SO4 pretreatments. The findings indicated that hemicelluloses were the dominant and positive factor, whereas cellulose and lignin had synergistic and negative effects on biomass digestibility. CONCLUSIONS: Using six pairs of Miscanthus samples with different cell wall compositions, hemicelluloses were revealed to be the dominant factor that positively determined biomass digestibility after pretreatments with NaOH or H2SO4 by negatively affecting cellulose crystallinity. The results suggested potential approaches to the genetic modifications of bioenergy crops.     

A comparison of chemical pretreatment methods for improving saccharification of cotton stalks

The effectiveness of sulfuric acid (H(2)SO(4)), sodium hydroxide (NaOH), hydrogen peroxide (H(2)O(2)), and ozone pretreatments for conversion of cotton stalks to ethanol was investigated. Ground cotton stalks at a solid loading of 10% (w/v) were pretreated with H(2)SO(4), NaOH, and H(2)O(2) at concentrations of 0.5%, 1%, and 2% (w/v). Treatment temperatures of 90 degrees C and 121 degrees C at 15 psi were investigated for residence times of 30, 60, and 90 min. Ozone pretreatment was performed at 4 degrees C with constant sparging of stalks in water. Solids from H(2)SO(4), NaOH, and H(2)O(2) pretreatments (at 2%, 60 min, 121 degrees C/15 psi) showed significant lignin degradation and/or high sugar availability and hence were hydrolyzed by Celluclast 1.5L and Novozym 188 at 50 degrees C. Sulfuric acid pretreatment resulted in the highest xylan reduction (95.23% for 2% acid, 90 min, 121 degrees C/15 psi) but the lowest cellulose to glucose conversion during hydrolysis (23.85%). Sodium hydroxide pretreatment resulted in the highest level of delignification (65.63% for 2% NaOH, 90 min, 121 degrees C/15 psi) and cellulose conversion (60.8%). Hydrogen peroxide pretreatment resulted in significantly lower (p相似文献   

Enhanced enzymatic hydrolysis of triploid poplar following stepwise acidic pretreatment and alkaline fractionation

In this study, we employed stepwise dilute sulfuric acid-catalyzed hydrothermal pretreatment and alkaline fractionation to enhance digestion of triploid poplar for bioconversion. Samples of triploid poplar were subjected to a pretreatment with 0.5% sulfuric acid at different temperatures and then to fractionation with 70% aqueous ethanol solution containing 1.5% NaOH. The results indicated that the stepwise pretreatment process degraded hemicelluloses, incurring slightly increase in crystallinity of cellulosic residues. Lignin was concentrated during acidic pretreatment and negatively affected the interaction between enzyme and cellulose. As the pretreatment temperature increased to 200 °C, the cellulose was degraded and exhibited lower crystallinity. The removal of polysaccharides and lignin resulted in mass loss and considerable feedstock recoveries were achieved at the temperatures below 130 °C. The results obtained from enzymatic hydrolysis suggested that the stepwise pretreatment enhanced the digestibility of the cellulosic residues. The optimum pretreatment temperature was observed at 120 °C. In this case 60.3% lignocellulose was recovered and achieved 69.4% of cellulose-to-glucose in enzyme-mediate conversion.     

Effects of organosolv pretreatment and enzymatic hydrolysis on cellulose structure and crystallinity in Loblolly pine

Ethanol organosolv pretreatment was performed on Loblolly pine to enhance the efficiency of enzymatic hydrolysis of cellulose to glucose. Solid-state ¹³C NMR spectroscopy coupled with line shape analysis was used to determine the structure and crystallinity of cellulose isolated from pretreated and enzyme-hydrolyzed Loblolly pine. The results indicate reduced crystallinity of the cellulose following the organosolv pretreatment, which renders the substrate easily hydrolyzable by cellulase. The degree of crystallinity increases and the relative proportion of para-crystalline and amorphous cellulose decreases after enzymatic hydrolysis, indicating preferential hydrolysis of these regions by cellulase. The structural and compositional changes in this material resulting from the organosolv pretreatment and cellulase enzyme hydrolysis of the pretreated wood were studied with solid-state CP/MAS ¹³C NMR spectroscopy. NMR spectra of the solid material before and after the treatments show that hemicelluloses and lignin are degraded during the organosolv pretreatment.     

Fractional purification and bioconversion of hemicelluloses

Hemicelluloses are types of plant cell wall polysaccharides, and the world's second most abundant renewable polymers after cellulose in lignocellulosic materials. They represent a type of hetero-polysaccharide with complex structure containing glucose, xylose, mannose, galactose, arabinose, rhamnose, glucuronic acid, and galacturonic acid in various amounts, depending on the source. Hemicelluloses are usually bonded to other cell-wall components such as cellulose, cell-wall proteins, lignin, and phenolic compounds by covalent and hydrogen bonds, and by ionic and hydrophobic interactions. This paper provides a review on hemicelluloses from lignocellulosic materials, especially in regard to their isolation and purification methods, and bioconversion. Current isolation and purification strategies are summarized, including: alkali peroxide extraction, organic solvent extraction, steam explosion, ultrasound-assisted extraction, microwave-assisted extraction, column chromatography, and membrane separation. In addition, the bioconversion of hemicelluloses including pretreatment, enzymatic hydrolysis, and fermentation are discussed.     

Two-stage pretreatment of rice straw using aqueous ammonia and dilute acid

Liberation of fermentable sugars from recalcitrant lignocellulosic biomass is one of the key challenges in production of cellulosic ethanol. Here we developed a two-stage pretreatment process using aqueous ammonia and dilute sulfuric acid in a percolation mode to improve production of fermentable sugars from rice straw. Aqueous NH? was used in the first stage which removed lignin selectively but left most of cellulose (97%) and hemicellulose (77%). Dilute acid was applied in the second stage which removed most of hemicellulose, partially disrupted the crystalline structure of cellulose, and thus enhanced enzymatic digestibility of cellulose in the solids remaining. Under the optimal pretreatment conditions, the enzymatic hydrolysis yields of the two-stage treated samples were 96.9% and 90.8% with enzyme loadings of 60 and 15FPU/g of glucan, respectively. The overall sugar conversions of cellulose and hemicellulose into glucose and xylose by enzymatic and acid hydrolysis reached 89.0% and 71.7%, respectively.     

Lignocellulose conversion for biofuel: a new pretreatment greatly improves downstream biocatalytic hydrolysis of various lignocellulosic materials

Background

Lignocellulosic biomass is an attractive renewable resource for future liquid transport fuel. Efficient and cost-effective production of bioethanol from lignocellulosic biomass depends on the development of a suitable pretreatment system. The aim of this study is to investigate a new pretreatment method that is highly efficient and effective for downstream biocatalytic hydrolysis of various lignocellulosic biomass materials, which can accelerate bioethanol commercialization.

Results

The optimal conditions for the hydrogen peroxide–acetic acid (HPAC) pretreatment were 80 °C, 2 h, and an equal volume mixture of H₂O₂ and CH₃COOH. Compared to organo-solvent pretreatment under the same conditions, the HPAC pretreatment was more effective at increasing enzymatic digestibility. After HPAC treatment, the composition of the recovered solid was 74.0 % cellulose, 20.0 % hemicelluloses, and 0.9 % lignin. Notably, 97.2 % of the lignin was removed with HPAC pretreatment. Fermentation of the hydrolyzates by S. cerevisiae resulted in 412 mL ethanol kg^?1 of biomass after 24 h, which was equivalent to 85.0 % of the maximum theoretical yield (based on the amount of glucose in the raw material).

Conclusion

The newly developed HPAC pretreatment was highly effective for removing lignin from lignocellulosic cell walls, resulting in enhanced enzymatic accessibility of the substrate and more efficient cellulose hydrolysis. This pretreatment produced less amounts of fermentative inhibitory compounds. In addition, HPAC pretreatment enables year-round operations, maximizing utilization of lignocellulosic biomass from various plant sources.

     

Optimization of alkaline pretreatment of coffee pulp for production of bioethanol

The use of lignocellulosic raw materials in bioethanol production has been intensively investigated in recent years. However, for efficient conversion to ethanol, many pretreatment steps are required prior to hydrolysis and fermentation. Coffee stands out as the most important agricultural product in Brazil and wastes such as pulp and coffee husk are generated during the wet and dry processing to obtain green grains, respectively. This work focused on the optimization of alkaline pretreatment of coffee pulp with the aim of making its use in the alcoholic fermentation. A central composite rotatable design was used with three independent variables: sodium hydroxide and calcium hydroxide concentrations and alkaline pretreatment time, totaling 17 experiments. After alkaline pretreatment the concentration of cellulose, hemicellulose, and lignin remaining in the material, the subsequent hydrolysis of the cellulose component and its fermentation of substrate were evaluated. The results indicated that pretreatment using 4% (w/v) sodium hydroxide solution, with no calcium hydroxide, and 25 min treatment time gave the best results (69.18% cellulose remaining, 44.15% hemicelluloses remaining, 25.19% lignin remaining, 38.13 g/L of reducing sugars, and 27.02 g/L of glucose) and produced 13.66 g/L of ethanol with a yield of 0.4 g ethanol/g glucose. © 2013 American Institute of Chemical Engineers Biotechnol. Prog., 30:451–462, 2014     

Restriction of the enzymatic hydrolysis of steam-pretreated spruce by lignin and hemicellulose

The presence of lignin is known to reduce the efficiency of the enzymatic hydrolysis of lignocellulosic raw materials. On the other hand, solubilization of hemicellulose, especially of xylan, is known to enhance the hydrolysis of cellulose. The enzymatic hydrolysis of spruce, recognized among the most challenging lignocellulosic substrates, was studied by commercial and purified enzymes from Trichoderma reesei. Previously, the enzymatic hydrolysis of steam pretreated spruce has been studied mainly by using commercial enzymes and no efforts have been taken to clarify the bottlenecks by using purified enzyme components.Steam-pretreated spruce was hydrolyzed with a mixture of Celluclast and Novozym 188 to obtain a hydrolysis residue, expectedly containing the most resistant components. The pretreated raw material and the hydrolysis residue were analyzed for the enrichment of structural bottlenecks during the hydrolysis. Lignin was removed from these two materials with chlorite delignification method in order to eliminate the limitations caused by lignin. Avicel was used for comparison as a known model substrate. Mixtures of purified enzymes were used to investigate the hydrolysis of the individual carbohydrates: cellulose, glucomannan and xylan in the substrates. The results reveal that factors limiting the hydrolysis are mainly due to the lignin, and to a minor extent by the lack of accessory enzymes. Removal of lignin doubled the hydrolysis degree of the raw material and the residue, and reached close to 100% of the theoretical within 2 days. The presence of xylan seems to limit the hydrolysability, especially of the delignified substrates. The hydrolysis results also revealed significant hemicellulose impurities in the commonly used cellulose model substrate, making it questionable to use Avicel as a model cellulose substrate for hydrolysis experiments.     

Ethanol production from cotton-based waste textiles

Ethanol production from cotton linter and waste of blue jeans textiles was investigated. In the best case, alkali pretreatment followed by enzymatic hydrolysis resulted in almost complete conversion of the cotton and jeans to glucose, which was then fermented by Saccharomyces cerevisiae to ethanol. If no pretreatment applied, hydrolyses of the textiles by cellulase and beta-glucosidase for 24 h followed by simultaneous saccharification and fermentation (SSF) in 4 days, resulted in 0.140-0.145 g ethanol/g textiles, which was 25-26% of the corresponding theoretical yield. A pretreatment with concentrated phosphoric acid prior to the hydrolysis improved ethanol production from the textiles up to 66% of the theoretical yield. However, the best results obtained from alkali pretreatment of the materials by NaOH. The alkaline pretreatment of cotton fibers were carried out with 0-20% NaOH at 0 degrees C, 23 degrees C and 100 degrees C, followed by enzymatic hydrolysis up to 4 days. In general, higher concentration of NaOH resulted in a better yield of the hydrolysis, whereas temperature had a reverse effect and better results were obtained at lower temperature. The best conditions for the alkali pretreatment of the cotton were obtained in this study at 12% NaOH and 0 degrees C and 3 h. In this condition, the materials with 3% solid content were enzymatically hydrolyzed at 85.1% of the theoretical yield in 24 h and 99.1% in 4 days. The alkali pretreatment of the waste textiles at these conditions and subsequent SSF resulted in 0.48 g ethanol/g pretreated textiles used.     

Mild alkaline/oxidative pretreatment of wheat straw

A new mild alkaline/oxidative pretreatment of wheat straw prior to enzymic hydrolysis was carried out. It consists of a first alkaline (1% NaOH for 24 h) step, which mainly solubilises hemicellullose and renders the material more accessible to further chemical attack, and a second alkaline/oxidative step (1% NaOH and 0·3% H₂O₂ for 24 h), which solubilises and oxidises lignin to minor polluting compounds. The entire process was carried out at low temperature (25–40°C) using a low concentration of chemicals, resulting in a relatively low cost and waste liquors containing only trace amounts of dangerous pollutants derived from lignin. Recovery of cellulose after the double pretreatment reached 90% of that contained in the starting material, with a concomitant 81% degradation of lignin. The action of a commercial cellulase on the cellulose obtained produced a syrup with a high concentration of reducing sugars (220 mg/ml), of which a large percentage was glucose.     

Deposition of lignin droplets produced during dilute acid pretreatment of maize stems retards enzymatic hydrolysis of cellulose

Electron microscopy of lignocellulosic biomass following high-temperature pretreatment revealed the presence of spherical formations on the surface of the residual biomass. The hypothesis that these droplet formations are composed of lignins and possible lignin carbohydrate complexes is being explored. Experiments were conducted to better understand the formation of these "lignin" droplets and the possible implications they might have on the enzymatic saccharification of pretreated biomass. It was demonstrated that these droplets are produced from corn stover during pretreatment under neutral and acidic pH at and above 130 degrees C, and that they can deposit back onto the surface of residual biomass. The deposition of droplets produced under certain pretreatment conditions (acidic pH; T > 150 degrees C) and captured onto pure cellulose was shown to have a negative effect (5-20%) on the enzymatic saccharification of this substrate. It was noted that droplet density (per unit area) was greater and droplet size more variable under conditions where the greatest impact on enzymatic cellulose conversion was observed. These results indicate that this phenomenon has the potential to adversely affect the efficiency of enzymatic conversion in a lignocellulosic biorefinery.     

Mild pretreatment of yellow poplar biomass using sequential dilute acid and enzymatically-generated peracetic acid to enhance cellulase accessibility

Biomass contains cellulose, xylan and lignin in a complex interwoven structure that hinders enzymatic hydrolysis of the cellulose. To separate these components in yellow poplar biomass, we sequentially pretreated with dilute sulfuric acid and enzymatically-generated peracetic acid. In the first step, the dilute acid with microwave heating (140°C, 5 min) hydrolyzed 90% of xylan. The xylose yield in hydrolysate after dilute acid pretreatment was 83.1%. In the second step, peracetic acid (60°C, 6 h) removed up to 80% of lignin. This sequential pretreatment fractionated biomass into xylan and lignin, leaving a solid residue enriched in cellulose (~80%). The sequential pretreatment enhanced enzymatic digestibility of the cellulase by removal of the other components in biomass. The glucose yield after enzymatic hydrolysis was 90.5% at a low cellulase loading (5 FPU/g of glucan), which is 1.6 and 18 times higher than for dilute acid-pretreated biomass and raw biomass, respectively. This novel sequential pretreatment with dilute acid and peracetic acid efficiently separates the three major components of yellow poplar biomass, and reduces the amount of cellulase needed.     

Influence of enzyme loading and physical parameters on the enzymatic hydrolysis of steam-pretreated softwood

Softwood is an interesting raw material for the production of fuel ethanol as a result of its high content of hexoses, and it has attracted attention especially in the Northern hemisphere. However, the enzymatic hydrolysis of softwood is not sufficiently efficient for the complete conversion of cellulose to glucose. Since an improvement in the glucose yield is of great importance for the overall economy of the process, the influence of various parameters on the cellulose conversion of steam-pretreated spruce has been investigated. The addition of beta-glucosidase up to 50 IU g(-)(1) cellulose to the enzymatic hydrolysis process resulted in increased cellulose conversion at a cellulase loading up to 48 FPU g(-)(1) cellulose. Despite very high enzyme loading (120 FPU g(-)(1) cellulose) only about 50% of the cellulose in steam-pretreated spruce was converted to glucose when all of the material following pretreatment was used in the hydrolysis step. The influence of temperature, residence time, and pH were investigated for washed pretreated spruce at a dry matter (DM) content of 5% and a cellulase activity of 18.5 FPU g(-)(1) cellulose. The optimal temperature was found to be dependent on both residence time and pH, and the maximum degree of cellulose conversion, 69.2%, was obtained at 38 degrees C and pH 4.9 for a residence time of 144 h. However, when the substrate concentration was changed from 5% to 2% DM, the cellulose conversion increased to 79.7%. An increase from 5% to 10% DM resulted, however, in a similar degree of cellulose conversion, despite a significant increase in the glucose concentration from 23 g L(-)(1) to 45 g L(-)(1). The deactivation of beta-glucosidase increased with increasing residence time and was more pronounced with vigorous agitation.     

Differences in glucose yield of residues from among varieties of rice,wheat, and sorghum after dilute acid pretreatment

Bio-refinery processes require use of the most suitable lignocellulosic biomass for enzymatic saccharification and microbial fermentation. Glucose yield from biomass solid fractions obtained after dilute sulfuric acid (1%) pretreatment (at 180 °C) was investigated using 14, 8, and 16 varieties of rice, wheat, and sorghum, respectively. Biomass solid fractions of each crop showed similar cellulose content. However, glucose yield after enzymatic hydrolysis (cellulase loading at 6.6 filter paper unit/g-biomass) was different among the varieties of each crop, indicating genotypic differences for rice, wheat, and sorghum. Nuclear magnetic resonance method revealed that the high residual level of lignin aromatic regions decreased glucose yield from solid fraction of sorghum.     

Steam-explosion of olive stones: hemicellulose solubilization and enhancement of enzymatic hydrolysis of cellulose

Olive stones (whole stones and seed husks in fragments) were processed by steam-explosion under different experimental conditions of temperature and time, 200-236 degrees C for 2-4 min, with or without previous acid impregnation with 0.1%, H2SO4 (w/w). This paper examines the solubilization of hemicelluloses and their molecular weight distribution. The subsequent enzymatic hydrolysis of the solid residue, using a preparation of cellulase, was also studied. The maximum yield of the pentosan recovered in the water solution was 63% pentose in the starting material for seed husk treated at 200 degrees C for 2 min (log R0 3.24) prior to acid-impregnation, or at 215 degrees C for 2 min (log R0 3.69) without acid, compared to 39% of the potential yield for whole stones pre-impregnated with acid under more severe conditions (at log R0 = 4.07). This indicates that the autohydrolysis of hemicellulose in seed husks when compared to whole stones is enhanced. The molecular weight distribution of profile sugars showed that the depolymerization of hemicelluloses is a function of the severity of the treatment. Steam-explosion improved the accessibility of the cellulose and increased the enzymatic hydrolysis yield after steam-explosion with respect to material without steam explosion (ball-milled material), although little increase in the extent of saccharification occurred when the alkali-soluble lignin was removed. Only when the substrate was post-treated with Na-chlorite was the enzymatic hydrolysis improved, the water-insoluble residue being almost completely hydrolyzed in 8 h of incubation.