Fabrication and characterization of electrospun chitosan nanofibers formed via templating with polyethylene oxide

Chitosan is an abundantly common, naturally occurring, polysaccharide biopolymer. Its biocompatible, biodegradable, and antimicrobial properties have led to significant research toward biological applications such as drug delivery, artificial tissue scaffolds for functional tissue engineering, and wound-healing dressings. For applications such as tissue scaffolding, formation of highly porous mats of nanometer-sized fibers, such as those fabricated via electrospinning, may be quite important. Previously, strong acidic solvents and blending with synthetic polymers have been used to achieve electrospun nanofibers containing chitosan. As an alternative approach, in this work, polyethylene oxide (PEO) has been used as a template to fabricate chitosan nanofibers by electrospinning in a core-sheath geometry, with the PEO sheath serving as a template for the chitosan core. Solutions of 3 wt % chitosan (in acetic acid) and 4 wt % PEO (in water) were found to have matching rheological properties that enabled efficient core-sheath fiber formation. After removing the PEO sheath by washing with deionized water, chitosan nanofibers were obtained. Electron microscopy confirmed nanofibers of approximately 250 nm diameter with a clear core-sheath geometry before sheath removal, and chitosan nanofibers of approximately 100 nm diameter after washing. The resultant fibers were characterized with IR spectroscopy and X-ray diffraction, and the mechanical and electrical properties were evaluated.     

Core-shell structured PEO-chitosan nanofibers by coaxial electrospinning

Core-shell structured PEO-chitosan nanofibers have been produced using a coaxial electrospinning setup. PEO and chitosan solutions, both in an aqueous acetic acid solvent, were used as the inner (core) and outer (shell) layer, respectively. Uniform-sized defect-free nanofibers of 150-190 nm diameter were produced. In addition, hollow nanofibers could be obtained subsequent to PEO washing of the membranes. The core-shell nanostructure and existence of chitosan on the shell layer were confirmed by TEM images obtained before and after washing the PEO content with water. The presence of chitosan on the surface of the composite nanofibers was further supported by XPS studies. The chitosan and PEO compositions in the nanofibrous mats were determined by TGA analysis, which were similar to their ratio in the feed solutions. The local compositional homogeneity of the membranes and the efficiency of the washing step to remove PEO were also verified by FTIR. In addition, DSC and XRD were used to characterize the crystalline structure and morphology of the co-electrospun nonwoven mats. The prepared coaxial nanofibers (hollow and solid) have several potential applications due to the presence of chitosan on their outer surfaces.     

Electrospun polyethylene oxide/cellulose nanocrystal composite nanofibrous mats with homogeneous and heterogeneous microstructures

An electrospinning process was successfully used to fabricate polyethylene oxide/cellulose nanocrystal (PEO/CNC) composite nanofibrous mats. Transition of homogeneous to heterogeneous microstructures was achieved by tailoring the concentration of PEO/CNC mixture in the solution from 5 to 7 wt %. Morphology investigation of the obtained nanofibers demonstrated that rod-shaped CNCs were well-dispersed in the as-spun nanofibers and highly aligned along the nanofiber long-axis. PEO/CNC nanofibers became more uniform and smaller in diameter with increased CNC-loading level. The heterogeneous composite mats were composed of rigid-flexible bimodal nanofibers. Results of structure characterization indicated that the incorporated CNCs interacted strongly with the PEO matrix through hydrogen bonding. Mechanical properties of both types of mats were effectively improved by using CNCs, with heterogeneous mats being stronger than their homogeneous counterparts for all compositions (0-20 wt % CNC contents). When a smaller diameter needle was used to form homogeneous mats, enhanced thermal and mechanical properties were obtained.     

Correlation of chitosan's rheological properties and its ability to electrospin

Chitosan-based, defect-free nanofibers with average diameters ranging from 62 +/- 9 nm to 129 +/- 16 nm were fabricated via electrospinning blended solutions of chitosan and polyethylene oxide (PEO). Several solution parameters such as acetic acid concentration, polymer concentration, and polymer molecular weight were investigated to optimize fiber consistency and diameter. These parameters were evaluated using the rheological properties of the solutions as well as images produced by scanning electron microscopy (SEM) of the electrospun nanofibers. Generally, SEM imaging demonstrated that as total polymer concentration (chitosan + PEO) increased, the number of beads decreased, and as chitosan concentration increased, fiber diameter decreased. Chitosan-PEO solutions phase separate over time; as a result, blended solutions were able to be electrospun with the weakest electric field and the least amount of complications when solutions were electrospun within 24 h of initially being blended. The addition of NaCl stabilized these solutions and increased the time the blended solutions could be stored before electrospinning. Pure chitosan nanofibers with high degrees of deacetylation (about 80%) were unable to be produced. When attempting to electrospin highly deacetylated chitosan from aqueous acetic acid at concentrations above the entanglement concentration, the electric field was insufficient to overcome the combined effect of the surface tension and viscosity of the solution. Therefore, the degree of deacetylation is an extremely important parameter to consider when attempting to electrospin chitosan.     

Electrospun poly(lactic acid)/chitosan core-shell structure nanofibers from homogeneous solution

The core-shell structure nanofibers of poly(lactic acid)/chitosan with different weight ratios were successfully electrospun from homogeneous solution. The preparation process was more simple and effective than double-needle electrospinning. The nanofibers were obtained with chitosan in shell while poly(lactic acid) in core attributing to phase separation, which were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and energy dispersive spectrometer (EDS). The electrospun nanofibrous membrane was evaluated in vitro by using mouse fibroblasts (L929) as reference cell lines. Cell culture results indicated that these materials were good in promoting cell growth and attachment, thus they could be used for tissue engineering and wound healing dressing.     

Electrospun scaffold tailored for tissue-specific extracellular matrix

The natural extracellular matrix (ECM) is a complex structure that is built to meet the specific requirements of the tissue and organ. Primarily consisting of nanometer diameter fibrils, ECM may contain other vital substances such as proteoglycans, glycosaminoglycan and various minerals. Current research in tissue engineering involves trying to replicate the ECM such that it provides the environment for tissue regeneration. Electrospinning is a versatile process that results in nanofibers by applying a high voltage to electrically charge a liquid. A variety of polymers and other substances have been incorporated into the artificial nanofibrous scaffold. Surface modification and cross-linking of the nanofibers are some ways to improve the biocompatibility and stability of the scaffold. Electrospun scaffolds with oriented nanofibers and other assemblies can be constructed by modifying the electrospinning setup. Using electrospinning, researchers are able to specifically tailor the electrospun scaffold to meet the requirements of the tissue that they seek to regenerate. In vitro and in vivo experiments demonstrate that electrospun scaffolds hold great potential for tissue engineering applications.     

In vitro study of smooth muscle cells on polycaprolactone and collagen nanofibrous matrices

Biodegradable polycaprolactone and collagen nanofibers were produced by electrospinning, with fiber diameters of around 300-700nm and features similar to the extracellular matrix of natural tissue. Human coronary artery smooth muscle cells (SMCs) seeded on nanofibrous matrices tend to maintain normal phenotypic shape and growth tends to be guided by the nanofiber orientation. The SMC and nanofibrous matrix interaction was observed by SEM, MTS assay, trypan blue exclusion method and laser scanning confocal microscopy. The results showed that the proliferation and growth rate of SMCs were not different on polycaprolactone (PCL) nanofibrous matrices coated with collagen or tissue culture plates. PCL nanofibrous matrices coated with collagen showed that the SMCs migrated towards inside the nanofibrous matrices and formed smooth muscle tissue. This approach may be useful for engineering a variety of tissues in various structures and shapes, and also to demonstrate the importance of matching both the initial mechanical properties and degradation rate of nanofibrous matrices to the specific tissue engineering.     

Effect of chitin/silk fibroin nanofibrous bicomponent structures on interaction with human epidermal keratinocytes

To fabricate a biomimetic nanostructured bicomponent scaffolds, two types of chitin/silk fibroin (SF) nanofibrous scaffolds (blend scaffolds and hybrid scaffolds) were prepared by electrospinning or simultaneous electrospinning of chitin/SF solutions. The chitin/SF bicomponent scaffolds were after-treated with water vapor, and their nanofibrous structures were almost maintained. From the cytocompatibility and cell behavior on the chitin/SF blend or hybrid nanofibrous scaffolds, the hybrid matrix with 25% chitin and 75% SF as well as the chitin/SF blend nanofibers could be a potential candidate for tissue engineering scaffolds.     

Hydrogels and electrospun nanofibrous scaffolds of N-methylene phosphonic chitosan as bioinspired osteoconductive materials for bone grafting

In this work, N-methylene phosphonic chitosan (NMPC) based hydrogels and electrospun nanofibrous scaffolds are reported with objective to obtain osteoconductive and osteoinductive matrixes for bone grafting applications. NMPC, a phosphorylated derivative of chitosan, is known to mimic the function of non collagenous phosphoproteins in providing nucleation sites for biomineralization. NMPC hydrogels were prepared by crosslinking between NMPC and genipin. A detailed investigation of physicochemical properties of NMPC solutions is also carried out in order to obtain beads free nanofibers. Both NMPC gels and nanofibers were further evaluated for their biomineralization potential and biocompatibility with human osteoblast like cells. Results indicated that hydrogels and nanofibrous scaffolds NMPC are biocompatible and significantly osteoinductive compared to tissue culture plate controls. However, cells seeded on nanofibrous scaffolds exhibited greater proliferation measured by MTT assay, and higher expression of early markers for osteogenic differentiation proving the superior applicability of nanofibrous scaffolds for bone grafting applications.     

Electrospun sodium alginate/poly(ethylene oxide) core-shell nanofibers scaffolds potential for tissue engineering applications

Core-shell structure nanofibers of sodium alginate/poly(ethylene oxide) were prepared via electrospinning their dispersions in water solution. The core-shell structure morphology of the obtained nanofibers was viewed under scanning electron microscope (SEM) and transmission electron microscope (TEM), and X-ray photoelectron spectroscopy (XPS) analysis was used to further quantify the chemical composition of the core-shell composite SA/PEO nanofibers surface in detail. Furthermore, one-step cross-linking method through being immersed in CaCl₂ solution was investigated to improve the anti-water property of the electrospun nanofibers mats in order to facilitate their practical applications as tissue engineering scaffolds, and the changes of the structural of nanofibers before and after cross-linking was characterized by Fourier transform infrared (FT-IR). Indirect cytotoxicity assessment indicated that SA/PEO nanofibers membrane was nontoxic to the fibroblasts cells, and cell culture suggested that SA/PEO nanofibers tended to promote fibroblasts cells attachment and proliferation. It was assumed that the nanofibers membrane of electrospun SA/PEO could be used for tissue engineering scaffolds.     

Nanofibers and their applications in tissue engineering

Developing scaffolds that mimic the architecture of tissue at the nanoscale is one of the major challenges in the field of tissue engineering. The development of nanofibers has greatly enhanced the scope for fabricating scaffolds that can potentially meet this challenge. Currently, there are three techniques available for the synthesis of nanofibers: electrospinning, self-assembly, and phase separation. Of these techniques, electrospinning is the most widely studied technique and has also demonstrated the most promising results in terms of tissue engineering applications. The availability of a wide range of natural and synthetic biomaterials has broadened the scope for development of nanofibrous scaffolds, especially using the electrospinning technique. The three dimensional synthetic biodegradable scaffolds designed using nanofibers serve as an excellent framework for cell adhesion, proliferation, and differentiation. Therefore, nanofibers, irrespective of their method of synthesis, have been used as scaffolds for musculoskeletal tissue engineering (including bone, cartilage, ligament, and skeletal muscle), skin tissue engineering, vascular tissue engineering, neural tissue engineering, and as carriers for the controlled delivery of drugs, proteins, and DNA. This review summarizes the currently available techniques for nanofiber synthesis and discusses the use of nanofibers in tissue engineering and drug delivery applications.     

Synthesis of Keratin-based Nanofiber for Biomedical Engineering

Electrospinning, due to its versatility and potential for applications in various fields, is being frequently used to fabricate nanofibers. Production of these porous nanofibers is of great interest due to their unique physiochemical properties. Here we elaborate on the fabrication of keratin containing poly (ε-caprolactone) (PCL) nanofibers (i.e., PCL/keratin composite fiber). Water soluble keratin was first extracted from human hair and mixed with PCL in different ratios. The blended solution of PCL/keratin was transformed into nanofibrous membranes using a laboratory designed electrospinning set up. Fiber morphology and mechanical properties of the obtained nanofiber were observed and measured using scanning electron microscopy and tensile tester. Furthermore, degradability and chemical properties of the nanofiber were studied by FTIR. SEM images showed uniform surface morphology for PCL/keratin fibers of different compositions. These PCL/keratin fibers also showed excellent mechanical properties such as Young''s modulus and failure point. Fibroblast cells were able to attach and proliferate thus proving good cell viability. Based on the characteristics discussed above, we can strongly argue that the blended nanofibers of natural and synthetic polymers can represent an excellent development of composite materials that can be used for different biomedical applications.     

Electrospinning of chitosan nanofibers: Processing optimization

In this study, the electrospinning of chitosan has been investigated. The problem of chitosan high viscosity, which limits its spinability, is resolved through the application of an alkali treatment which hydrolyzes chitosan chains and so decreases its their molecular weight. Solutions of the treated chitosan in aqueous 70–90% acetic acid produce nanofibers with appropriate quality and processing stability. Decreasing the acetic acid concentration in the solvent increases the mean diameter of the nanofibers. Optimum nanofibers are achieved with chitosan which is hydrolyzed for 48 h. Such nanofibers result in a moisture regain which is 74% greater than that of treated and untreated chitosan powder. The diameter of this nanofiber, 140 nm, is strongly affected by the electrospinning conditions as well as by the concentration of the solvent. FTIR investigations prove that neither the alkali treatment nor the electrospinning process change the chemical nature of the polymer.     

Electrospun water-soluble carboxyethyl chitosan/poly(vinyl alcohol) nanofibrous membrane as potential wound dressing for skin regeneration

Biocompatible carboxyethyl chitosan/poly(vinyl alcohol) (CECS/PVA) nanofibers were successfully prepared by electrospinning of aqueous CECS/PVA solution. The composite nanofibrous membranes were subjected to detailed analysis by scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and X-ray diffraction (XRD). SEM images showed that the morphology and diameter of the nanofibers were mainly affected by the weight ratio of CECS/PVA. XRD and DSC demonstrated that there was strong intermolecular hydrogen bonding between the molecules of CECS and PVA. The crystalline microstructure of the electrospun fibers was not well developed. The potential use of the CECS/PVA electrospun fiber mats as scaffolding materials for skin regeneration was evaluated in vitro using mouse fibroblasts (L929) as reference cell lines. Indirect cytotoxicity assessment of the fiber mats indicated that the CECS/PVA electrospun mat was nontoxic to the L929 cell. Cell culture results showed that fibrous mats were good in promoting the cell attachment and proliferation. This novel electrospun matrix would be used as potential wound dressing for skin regeneration.     

基于 AOPAN 纳米纤维膜的粘杆菌素发酵液后处理研究

使用静电纺丝再经胺肟化改性制备AOPAN纳米纤维膜,并基于AOPAN纳米纤维膜构建膜分离装置,用于粘杆菌素发酵液的后处理。研究中,对不同厚度的纳米纤维膜的渗透通量及分离性能进行比较,最终确定双层叠合的纳米纤维膜为分离膜,最适操作压力为0.14 MPa。在此条件下,分离膜的渗透通量为2.61 L/m2．min,蛋白质的截留率达到90％,色素等其他杂质也得到有效去除。     

Enzyme-carrying polymeric nanofibers prepared via electrospinning for use as unique biocatalysts

Improvement of catalytic efficiency of immobilized enzymes via materials engineering was demonstrated through the preparation of bioactive nanofibers. Bioactive polystyrene (PS) nanofibers with a typical diameter of 120 nm were prepared and examined for catalytic efficiency for biotransformations. The nanofibers were produced by electrospinning functionalized PS, followed by the chemical attachment of a model enzyme, alpha-chymotrypsin. The observed enzyme loading as determined by active site titration was up to 1.4% (wt/wt), corresponding to over 27.4% monolayer coverage of the external surface of nanofibers. The apparent hydrolytic activity of the nanofibrous enzyme in aqueous solutions was over 65% of that of the native enzyme, indicating a high catalytic efficiency as compared to other forms of immobilized enzymes. Furthermore, nanofibrous alpha-chymotrypsin exhibited a much-improved nonaqueous activity that was over 3 orders of magnitude higher than that of its native counterpart suspended in organic solvents including hexane and isooctane. It appeared that the covalent binding also improved the enzyme's stability against structural denaturation, such that the half-life of the nanofibrous enzyme in methanol was 18-fold longer than that of the native enzyme.     

Morphological and surface properties of electrospun chitosan nanofibers

Nonwoven fiber mats of chitosan with potential applications in air and water filtration were successfully made by electrospinning of chitosan and poly(ethyleneoxide) (PEO) blend solutions. Electrospinning of pure chitosan was hindered by its limited solubility in aqueous acids and high degree of inter- and intrachain hydrogen bonding. Nanometer-sized fibers with fiber diameter as low as 80 +/- 35 nm without bead defects were made by electrospinning high molecular weight chitosan/PEO (95:5) blends. Fiber formation was characterized by fiber shape and size and was found to be strongly governed by the polymer molecular weight, blend ratios, polymer concentration, choice of solvent, and degree of deacetylation of chitosan. Weight fractions of polymers in the electrospun nonwoven fibers mats were determined by thermal gravimetric analysis and were similar to ratio of polymers in the blend solution. Surface properties of fiber mats were determined by measuring the binding efficiency of toxic heavy metal ions like chromium, and they were found to be related with fiber composition and structure.     

Effects of chain conformation and entanglement on the electrospinning of pure alginate

As a natural biopolymer, sodium alginate (SA) has been widely used in the biomedical field in the form of powder, liquid, gel, and compact solid, but not in the form of nanofiber. Electrospinning is an effective method to fabricate nanofibers. However, electrospinning of SA from its aqueous solution is still a challenge. In this study, an effort has been made to solve this problem and find the key reasons that hinder the electrospinning of alginate aqueous solution. Through this research, it was found that pure SA nanofibers could be fabricated successfully by introducing a strong polar cosolvent, glycerol, into the SA aqueous solutions. The study on the properties of the modified SA solution showed that increasing glycerol content increased the viscosity of the SA solution greatly and, meanwhile, decreased the surface tension and the conductivity of the SA solution. The rheological results indicated that the increase in glycerol content could result in the enhanced entanglements of SA chains. Two schematic molecular models were proposed to depict the change of SA chain conformation in aqueous solution with and without glycerol. The main contribution of glycerol to the electrospinning process is to improve the flexibility and entanglement of SA chains by disrupting the strong inter- and intramolecular hydrogen bondings among SA chains, then forming new hydrogen bondings with SA chains.     

Antioxidant effects of chrysin-loaded electrospun nanofibrous mats on proliferation and stemness preservation of human adipose-derived stem cells

An ideal biomaterial in regenerative medicine should be able to regulate the stem cell proliferation without the loss of its pluripotency. Chrysin (Chr) is a naturally occurring flavone with a wide spectrum of biological functions including anti-inflammatory and anti-oxidant properties. The present study describes the influence of Chr-loaded nanofibrous mats on the regulation of proliferation and stemness preservation of adipose-derived stem cells (ADSCs). For this purpose, Chr-loaded poly (ε-caprolactone)/poly (ethylene glycol) (PCL/PEG) nanofibrous mats were produced via electrospinning process and the successful fabrication of these bioactive mats was confirmed by field emission scanning electron microscopy (FE-SEM) and fourier transform infrared spectroscopy. ADSCs were seeded on the nanofibers and their morphology, viability, and stemness expression were analyzed using FE-SEM, MTT, and qPCR assays after 2 weeks of incubation, respectively. The results display that ADSCs exhibit better adhesion and significantly increased viability on the Chr-loaded PCL/PEG nanofibrous mats in relative to the PCL/PEG nanofibers and tissue culture polystyrene. The greater viability of ADSCs on Chr based nanofibers was further confirmed by higher expression levels of stemness markers Sox-2, Nanog, Oct-4, and Rex-1. These findings demonstrate that Chr-loaded PCL/PEG electrospun nanofibrous mats can be applied to improve cell adhesion and proliferation while concurrently preserving the stemness of ADSCs, thus representing a hopeful potential for application in stem cell therapy strategies.