The Gallocyanin-Chrome Alum Stain; Influence of Methods of Preparation on Its Activity and Separation of Active Staining Compound

A dye, which is probably a cationic chelate, has been separated from a gallocyanin-chrome alum staining solution and prepared in the dry form. This dye is apparently the major staining compound. To prepare the chelate or dye, dissolve 150 mg of gallocyanin and 15 gm of chrome alum in 100 ml of distilled water and boil for 10-20 min, cool, filter, wash the precipitate with sufficient distilled water to restore the volume of the filtrate to 100 ml, then add concentrated NH₄OH until the pH is raised to 8-8.5. Filter, with suction, through a medium porosity fritted glass funnel. Wash with 100-200 ml of anhydrous ethyl ether and air dry the precipitate. This ratio of chrome alum to gallocyanin and the 10-20 min boiling time are optimal for preparation of the staining solution, which may be used either for staining or for separation of the chelate in its dry form. From the dried chelate, the staining solution is prepared as a 3% solution in1 N H₂SO₄ and a staining time of 16-24 hr is required. No differentiation is needed; the stain is self-limiting.     

A Ribonuclease-Gallocyanin Stain for Sexing Skin Biopsies

Skin biopsies for sexing can be fixed best in 10-15% aqueous formalin or this solution saturated with HgCl₂. Bouin's fluid and all chromate mixtures should be avoided. Celloidin-paraffin double embedding is recommended but not essential. Sections are brought to water, mercurial residues removed if necessary, and then washed in distilled water. They are incubated at 37°C in a ribo-nuclease solution: approximately 1 mg of ribonuclease powder (Light's) in 100 ml of glass-distilled water; boiled 3-5 sec after dissolving, and kept in a refrigerator (usable about a week). The sections are rinsed and incubated at 37°C overnight in gallocyanin-chromalum (Einarson, 1951) made as follows: Dissolve 5 gm of chromalum in 100 ml of distilled water, add 0.15 gm of gallocyanin, shake thoroughly, heat slowly and boil 5 min; cool, filter, and wash through the filter with distilled water until the filtrate reaches 100 ml. This solution is usable at once and keeps at least a month. Sections should be dipped in acid alcohol to clean (optional), but no attempt made to differentiate them, and washed in tap water. Dehydration, clearing and covering complete the process. The method is nearly as precise as the Feulgen and more convenient and reliable for routine use on miscellaneous material.     

Differentiated Staining of Osmium Tetroxide-Fixed, Vestopal-w-Embedded Tissue in thin Sections

Tissues were fixed at 20° C for 1 hr in 1% OsO₄, buffered at pH 7.4 with veronal-acetate (Palade's fixative), soaked 5 min in the same buffer without OsO₄, then dehydrated in buffer-acetone mixtures of 30, 50, 75 and 90% acetone content, and finally in anhydrous acetone. Infiltration was accomplished through Vestopal-W-acetone mixtures of 1:3, 1:1, 3:1 to undiluted Vestopal. After polymerisation at 60° C for 24 hr, 1-2 μ sections were cut, dried on slides without adhesive, and stained by any of the following methods. (1) Mayer's acid hemalum: Flood the slides with the staining solution and allow to stand at 20°C for 2-3 hr while the water of the solution evaporates; wash in distilled water, 2 min; differentiate in 1% HCl; rinse 1-2 sec in 10% NH,OH. (2) Iron-trioxyhematein (of Hansen): Apply the staining solution as in method 1; wash 3-5 min in 5% acetic acid; restain for 1-12 hr by flooding with a mixture consisting of staining solution, 2 parts, and 1 part of a 1:1 mixture of 2% acetic acid and 2% H₂SO₄ (observe under microscope for staining intensity); wash 2 min in distilled water and 1 hr in tap water. (3) Iron-hematoxylin (Heidenhain): Mordant 6 hr in 2.5% iron-alum solution; wash 1 min in distilled water; stain in 1% or 0.5% ripened hematoxylin for 3-12 br; differentiate 8 min in 2.5%, and 15 min in 1% iron-alum solution; wash 1 hr in tap water. (4) Aceto-carmine (Schneider): Stain 12-24 hr; wash 0.5-1.0 min in distilled water. (5) Picrofuchsin: Stain 24-48 hr in 1% acid fuchsin dissolved in saturated aqueous picric acid; differentiate for only 1-2 sec in 96% ethanol. (6) Modified Giemsa: Mix 640 ml of a solution of 9.08 gm KH₂PO₄ in 1000 ml of distilled water and 360 ml of a solution of 11.88 gm Na₂HPO₄-2H₂O in 1000 ml of distilled water. Soak sections in this buffer, 12 hr. Dissolve 1.0 gm of azur I in 125 ml of boiling distilled water; add 0.5 gm of methylene blue; filter and add hot distilled water until a volume of 250 ml is reached (solution “AM”). Dissolve 1.5 gm of eosin, yellowish, in 250 ml of hot distilled water; filter (solution “E”). Mix 1.5 ml of “AM” in 100 ml of buffer with 3 ml of “E” in 100 ml of buffer. Stain 12-24 hr. Differentiate 3 sec in 25 ml methyl benzoate in 75 ml dioxane; 3 sec in 35 ml methyl benzoate in 65 ml acetone; 3 sec in 30 ml acetone in 70 ml methyl benzoate; and 3 sec in 5 ml acetone in 95 ml methyl benzoate. Dehydrated sections may be covered in a neutral synthetic resin (Caedax was used).     

Counterstaining Golgi-Cox Impregnations with Luxol Fast Blue as a Myelin Stain

Immerse pieces of brain tissue 4 wk in solutions A and B, mixed just before use: A. K₂Cr₂O₇, 1 gm; HgCl₂, 1 gm; boiling distilled water, 85 ml. Boil A for 15 min, cool to 2 C and add: B. K₂CrO₄, 0.8 gm; Na₂WO₄, 0.5 gm; distilled water, 20 ml. Rinse in water and immerse 24 hr in LiOH, 0.5 gm; KNO₃, 15 gm; distilled water, 100 ml. Wash 24 hr in several changes of 0.2% acetic acid and then for 2 hr in tap water. Dehydrate and embed in celloidin. Process a 60 μ section through 70 and 95% ethanol, a 3:1 mixture of absolute ethanol and chloroform, and toluene. Immerse it for 5 min in a solution containing methyl benzoate, 25 ml; benzyl alcohol, 100 ml; chloroform, 75 ml. Orient the section on a chemically clean slide and let air-dry 5-10 min. Process through toluene, 3:1 ethanol-chloroform and 95% ethanol. Place the section for 5-60 min at 60 C in a solution made up of: Luxol fast blue G (Matheson, Coleman and Bell), 1 gm; 95% ethanol, 1000 ml; 10% acetic acid, 5 ml. Hydrate to water and immerse in 0.05% Li₂CO₃ for 3-4 min. Differentiate in 70% ethanol and place in water. Immerse for 5-15 min in a mixture of two solutions: A. cresylechtviolet (Otto C. Watzka, Montreal), 2 gm; 1 M acetic acid, 185 ml; B. 1 M sodium acetate, 15 ml; distilled water, 400 ml; absolute ethanol, 200 ml. Dehydrate to 3:1 ethanol-chloroform. Clear in toluene and apply a coverslip. The technique produces fast Golgi-Cox impregnated neurons against a background of counterstained myelinated fibers. Patterns of the myelinated fibers can be used to localize impregnated neurons.     

A Tungstate Modification of the Golgi-Cox Method

Pieces of fresh nervous tissue 4-5 mm thick are put into the following solution: HgCl₂, 1 gm; K₂Cr₂O₇, 1 gm; K₂CrO₄, 0.8 gm; K₂WO₄ (or Na₂WO₄), 0.5 gm; distilled water 100 ml. They are kept undisturbed in the dark at room temperature for 20-30 days, then transferred to the following alkaline solution: LiOH (or NaOH), 1 gm; KNO₃, 15 gm; distilled water, 100 ml. After 12-24 hr in this solution they are washed for 12-24 hr in several changes of distilled water. (If sodium hydroxide was used, 0.5 ml of acetic acid should be added per 100 ml of wash water.) Embedding in celloidin follows dehydration. Sections are dehydrated in 3 parts of absolute alcohol and 1 part of chloroform, cleared in iodobenzene and mounted with a cover slip using a mounting medium with a refractive index around 1.61. The use of tungstate improves the general results and allows especially successful impregnations in very young animals, when the usual technic fails.     

A Self-Limiting, Highly Selective Chromium-Hematoxylin Stain

A compound, which is probably a cationic chelate, can be isolated as a dry powder from a hematoxylin-chrome alum lake. In aqueous acid solution this compound is an excellent nuclear stain which is extremely selective, very resistant to acids and alcohols, and self-limiting. Staining time may vary from 20 min to 16 hr without causing significant differences in staining intensity. To prepare the dry stain, dissolve 10 gm of hematoxylin, 10 gm of NaOH and 70 gm of chrome alum in 600 ml of distilled water, boil 20 min, cool and filter, allowing the filtrate to drop into 3.5 liters of absolute alcohol. Filter off the precipitate formed in the alcohol, and air dry it at room temperature. The staining solution is prepared by dissolving 3 gm of the dried precipitate in 100 ml of 3% HCl.     

Specific Staining of Glycogen with Haematoxylin and Certain Anthraquinone Dyes

Specific staining of glycogen in rat liver fixed in chilled 80% alcohol, chilled formol alcohol or 10% neutral formalin has been accomplished with acid alizarin blue SWR, alizarin brilliant blue BS, alizarin red S, gallein, haematein, and haematoxylin solutions. TO prepare a staining solution, 1 gm dye, 1 gm K₂CO₃ and 5 gm KCl were dissolved by heating in 60 ml of water. Concentrated NH₄OH (0.880 sp.gr.), 15 ml, followed by 15 ml of dry methanol were added to 20 ml of the cooled solution. Paraffi sections were stained for 5 min, rinsed in dry methanol, cleared in xylene, and mounted in D.P.X. The high specificity obviated the need for counterstaining: nuclei and cytoplasm were unstained. Precipitation of stain onto the slide was rare. As all the dyes carried, like carminic acid, numerous groups capable of forming hydrogen bonds, it is suggested that the staining mechanism involved hydrogen bonding.     

Handling Germinated Pollen on Millipore Membrane During the Feulgen and Autoradiographic Procedures

To prevent loss of pollen during the Feulgen's procedure, the pollen was grown on an autoclaved membrane filter (Millipore AA WP 025 00) in contact with a sterilized medium containing agar 0.5-1%, sucrose according to the genus (Malus 0.3-0.5 M; Persica and Tulipa 0.4 M), and H₃BO₃, 0.01%. To fix the germinated pollen of most species, the membrane was placed for 2 hr to overnight at 2-4 C on filter paper wet with the following mixture: OsO₄, 1 gm; CrO₃, 1.66 gm; and distilled water, 233 ml. To fix Persica pollen, 10% of glacial acetic acid had to be added to the fixative. Washing with distilled water and bleaching with a mixture of 3% H₂O₂ and sat. aq. ammonium oxalate, 1:1, were performed also on filter paper. Similarly, the preparation was processed for Feulgen staining by use of pieces of filter paper wet with the required fluids. Hydrolysis preceding the Schiff's reagent was performed at room temperature with 5 N HCl for 18 min. The differentiation after the Schiff's action was with 2% K₂S₂O₅ buffered to pH 2.3 with 9 ml of phosphate buffer (KH₂PO₄, 1.4 gm; conc. HCl, 0.35 ml and distilled water to make 100 ml). The stained pollen was floated off the membrane with a drop of glacial acetic acid to a gelatinized or an albumenized slide, and squashed. When the coverslip is removed the preparation may be either dehydrated and mounted or coated with autoradiographic film.     

A Formalin-Wright Staining Technique for Avian Blood Cells

A rather concentrated alcoholic staining solution, an aqueous formalin-containing diluent, and a mixture of ethyl ether and absolute methyl alcohol are required. Formulas: A. Wright's stain (Harleco, Cert. No. LWr-52 was used), 3.3 gm; methyl alcohol, 500 ml. B. Formaldehyde solution 40% USP (Fisher's used), 0.25 ml; distilled water, 500 ml with its pH adjusted to 6.8 by addition of either 0.25% Na₂CO₂ or 0.25% HCl, as needed. C. A I:I mixture of ethyl ether and absolute methyl alcohol. Procedure: Prepare thin smears of normal or pathological avian blood, air dry, place the slides on a drying rack, cover with solution A, and let stand for about 8 min. Dilute the stain by dropping on a volume of B estimated to be equal to the volume of the partially evaporated stain, and let stand for 2-5 min, or until the surface is well covered by a metallic sheen. Wash with distilled water adjusted to pH 6.8 with the 0.25% Na₂CO₂ solution or 0.25% HCl. Dry the preparations quickly by blotting with filter paper. Differentiate and adjust the color intensities by dipping 6-10 times into C. Check the results microscopically and differentiate further if the colors are not properly balanced. Dry, uncovered preparations may be examined under oil; or, a cover glass can be applied with balsam or a synthetic resin for permanent mount. Results are similar to those described in textbooks, but have been more consistent than those obtained with other techniques for blood cells of chicken, pheasants, American and Indian partridge, quail, pigeon, turkey, goose, canary, and the Himalayan snow partridge.     

Staining Reticulin with Gold

This bromine-iodine-gold chloride-reduction sequence stains reticulin in formalin-fixed paraffin sections without risk of sections becoming detached. After hydration, sections are exposed to 0.2% bromine water containing 0.01% KBr for 1 hr, then rinsed and placed for 5 min in a solution consisting of KI, 2 gm; iodine crystals, 1 gm; and distilled water, 100 ml. After this the sections are well washed in distilled water, immersed for 5 min in 1% w/v aqueous solution of chloro-auric acid, again rinsed in distilled water, and the gold is reduced by placing in freshly made 3% H₂O₂ for 2-4 hr at 37 C, or in 2% oxalic acid for 1-3 hr at the same temperature.     

Staining Tissue of the Central Nervous System with Luxol Fast Blue and Neutral Red

The tissue is fixed in 10% neutral saline formalin for 1 day to 3 wk depending on the size of the block, dehydrated and embedded in paraffin. The sections are stained at 57° C for 2 hr, then at 22° C for 30 min, in a 0.0125% solution of Luxol fast blue in 95% alcohol acidified by 0.1% acetic acid. They are differentiated in a solution consisting of: Li₂CO₃, 5.0 gm; LiOH-H₂O, 0.01 gm; and distilled water, 1 liter at 0-1° C, followed by 70% alcohol, and then treated with 0.2% NaHSO₃. They are soaked 1 min in an acetic acid-sodium acetate buffer 0.1 N, pH 5.6, then stained with 0.03% buffered aqueous neutral red. Sections are washed in distilled water, 1 sec, then treated with the following solution: CuSO₄·5H₂O, 0.5 gm; CrK(SO₄)₂·12H₂O, 0.5 gm; 10% acetic acid, 3 ml; and distilled water, 250 ml. Dehydration, clearing and covering complete the process. Myelin sheaths are stained bright blue; meninges and the adventitia of blood vessels are blue; red blood cells are green. Nissl material is stained brilliant red; axon hillocks, axis cylinders, ependyma, nuclei and some cytoplasm of neuroglia, media and endothelium of blood vessels are pink.     

A Controllable Differential Stain for the Hypophysis by Adaptation of the Mallory Triple Stain

A selective and controllable staining method for the hypophysis has been developed with rat material, using Mallory's triple stain as a basis.

Fix in Zenker neutral formol for 6 hours. Longer fixation is undesirable. Transfer to 30% alcohol plus a few drops of a saturated solution of I₂ in aqueous KI over night. Gradually complete dehydration and clear in cedar oil. Infiltrate with a paraffin mixture (paraffin, rubber-paraffin, bayberry wax and beeswax). Section 3-Sμ. Hydrate to distilled water, placing a few drops of a KI-I₂ solution in the 50% alcohol. Stain in 1% acid fuchsia for 30 minutes. Rinse, and differentiate in a weak NH₄OH solution (one drop 28% NH₄OH to 200 cc. HOH). When differentiation is complete, transfer to a 0.5% phosphomolybdic acid solution for 3 minutes, after first stopping the differentiation with a 0.1% HC1 solution and then rinsing with distilled water. Stain for one hour in a solution of: 1% anilin blue, water soluble, 2% orange 6, and 1% phosphomolybdic acid. Rinse in distilled water plus a few cubic centimeters of the stain. Differentiate in 95% alcohol, transfer to absolute alcohol and clear in a mixture of 30% oil of cedar, 40% oil of thyme, 15% absolute alcohol and 15% xylene. Finally, transfer to xylene and mount.     

The Quantitative Determination of Osmium Tetroxide in Fixatives

This rapid spectrophotometric method for determining the OsO₄ concentration in fixative and stock solutions is based on the reduction of OsO₄ by acidified KI to the blue species of OsI₆ =, which is then determined at 649 mµ. The salt K₂OsI₆ has been isolated from the reaction mixture and characterized. Method: A I ml aliquot of the solution, containing up to 3% OsO₄, is diluted to 100 ml with distilled water. To 1 ml of the diluted solution is added, in order: distilled water, 2 ml; 1 M HCI, 1 ml; and 1 M KI, 1 ml. Optical density at 649 mµ is read from 10-120 min thereafter. OsO₄ concentration is calculated from the measured molecular extinction coefficient of OsI₆ =, 4400 liter/mole cm.     

Luxol Fast Blue Arn: A New Solvent Azo Dye with Improved Staining Qualities for Myelin and Phospholipids

Luxol fast blue ARN (Du Pont, C.I. solvent blue 37) is a diarylguanidine salt of a sulfonated azo dye. This dye was compared with other Luxol blue and Luxol black dyes. Luxol fast blue ARN has improved staining qualities for phospholipids and myelin, and can advantageously be substituted for Luxol fast blue MBS (MBSN). Appropriate staining times for a 0.1% dye solution in 95% ethanol (containing 0.02% acetic add) at 35°-40° C range from 2-3 hr. After staining, the sections should be rinsed in 95% ethanol, rinsed in distilled water, and differentiated for 2 sec in 0.005% Li₂CO₃, rinsed in 70% ethanol, washed in water, and counterstained as required. Phospholipids and myelin selectively stain deep blue. A fixative containing CaCl₂, 1%; cetyltrimethylammonium bromide, 0.5%; and formaldehyde, 10%, in water gave excellent results with brain. However, 10% formalin can be used. The staining of the phospholipids is probably due to the formation of dye-phospholipid complexes.     

Staining Methods For Studying Ingredient Distribution In Baked Cakes

A method is described for preparing cake crumb for sectioning and staining. Previous to embedding, the fat was stained and fixed by exposing small blocks of cake to the fumes from a 5%, freshly-prepared, aqueous solution of osmic acid (OsO₄). This was followed by dehydration in ethyl alcohol and tertiary butyl alcohol, removal of air under vacuum and infiltration with paraffin.

Sections were cut 20 and 9Op thick and mounted with water.

Wax was removed by immersion in xylene. The sections were rehydrated in a series of ethyl alcohol dilutions, from concentrated to dilute, then transferred to distilled water.

Protein was then stained pink by immersion of the slides in an acidified 0.04% water solution of eosin Y, or starch was stained blue with a dilute aqueous solution of iodine. Ten grams iodine and 10 g. KI were dissolved in 25 ml. distilled water. This stock solution was diluted for use one to two hundred times.

The relationship between protein and starch was demonstrated by staining the sections with eosin, differentiating in 50% alcohol and staining with iodine.

When slides of cake crumb were prepared in this way, the fat was stained black, the protein bright pink and the starch granules a dark blue.     

A Nissl Method Using Buffered Solutions of Thionin

Experiments were performed in an attempt to obtain a rapid method for staining the chromophilic substance of formalin-fixed nerve cells differentially without resorting to over-staining and subsequent acid-decolorizing. A satisfactory procedure using thionin in dilute buffered solutions was developed: Prepare a stock solution of the dye using 1 g. in 100 ml. of distilled water. Prepare veronal-acetate buffers (Michaelis, 1931) in the range of pH 5 to pH 3.S. To each 10 ml. of the buffer add 0.5 ml. of the stock dye solution. After rinsing in CO₂-free distilled water place mounted or unmounted sections in this solution. (Freshly fixed material, 10μ to 20μ thick, is completely stained in 10 to 20 minutes but over-staining does not occur when longer times are allowed.) Return sections to distilled water (2 changes) and wash until diffusion of excess dye is no longer visible. Wash in 70% ethyl alcohol (2 changes) until diffusion of excess dye is no longer visible. Dehydrate in 95% ethyl alcohol and normal butyl alcohol, clear and mount.

Optimum staining of chromophilic material occurs at pH 3.65. Glial processes are well stained at pH 4.6. Nissl bodies and glial cytoplasm are purplish blue, nuclear chromatin is blue, background is clear at pH 3.65 but pale blue at pH 4.9.     

Selective Staining of Neurosecretory Material in Semithin Epoxy Sections by Gomori's Aldehyde Fuchsin

The epoxy resin was removed from semithin (1 μm) sections by immersing them for 30 sec in sodium methoxide (Mayor et al., J. Biophys. Biochem. Cytol., 9: 909-10, 1961) and then processed as follows: (1) left for 1-3 hr at 60 C in a mixture of formalin, 25 ml; glacial acetic acid, 5 ml; CrO₃, 3 gm; and distilled water, 75 ml: (2) oxidized 10 min in a 1:1:6 v/v mixture of 2.5% KMnO₄, 5% H₂SO₄ and distilled water: (3) bleached in 1% oxalic acid, and (4) stained for 15 min in aldehyde fuchsin, 0.125% in 70% alcohol, or in a 1% aqueous solution of toluidine blue. The neurosecretory material is selectively stained.     

Phosphotungstic Acid-Eosin Combined with Hematoxylin as A Stain for Negri Bodies in Paraffin Sections

Experimentation with the Papanicolaou stain in this laboratory led to the discovery that the eosin, combined with phosphotungstic acid, was responsible for differential staining of Negri bodies. Eosin prepared as in EA 36 was used, but without the light green and Bismarck brown. Paraffin sections of hippocampus from brains of animal affected with rabies were fixed in 10% formol or in a mixture of 2 volumes of saturated aqueous HgCl₂ and 1 volume of absolute alcohol. They were stained first with hematoxylin and then with eosin. This procedure gave better results than staining with other types of eosin or by the original EA 36 mixture. The Negri bodies were well stained and their structure easily visible. The best results were obtained from material fixed with the HgCl₂ solution.     

The Differentiation of Live From Dead Sperms in Fowl Semen

A combined stain solution is made by dissolving 0.1 gm bromphenol blue and 0.2 gm nigrosin in 100 ml of a M/15 buffer solution of KH₂PO₄ and Na₂HPO₄ adjusted to pH 7.5. This staining solution was used to prepare stained fowl semen smears. Such smears give stable differentiation of live from dead sperms. The dead sperms are stained with a dark violet color while the live ones are not stained.     

Luxol Fast Blue Mbs: A Stain for Phase Contrast Microscopy

A staining method to increase the contrast of sectioned material for phase contrast microscopy is described. Two stock solutions of the stain are required. The first is made by dissolving 2 gm of luxol fast blue MBS in 100 ml of 95% ethanol. The second solution is made up of 4 ml of a 29% aqueous solution of FeCl₃, 95 ml of 95% ethanol, and 1 ml of concentrated HCl. The staining solution is made by mixing equal parts of the two solutions. Sections are deparaffinized and taken to 70% alcohol, stained for 1.5 hr, dehydrated, cleared and covered as usual.