Biodiesel production—current state of the art and challenges

Biodiesel is a clean-burning fuel produced from grease, vegetable oils, or animal fats. Biodiesel is produced by transesterification of oils with short-chain alcohols or by the esterification of fatty acids. The transesterification reaction consists of transforming triglycerides into fatty acid alkyl esters, in the presence of an alcohol, such as methanol or ethanol, and a catalyst, such as an alkali or acid, with glycerol as a byproduct. Because of diminishing petroleum reserves and the deleterious environmental consequences of exhaust gases from petroleum diesel, biodiesel has attracted attention during the past few years as a renewable and environmentally friendly fuel. Since biodiesel is made entirely from vegetable oil or animal fats, it is renewable and biodegradable. The majority of biodiesel today is produced by alkali-catalyzed transesterification with methanol, which results in a relatively short reaction time. However, the vegetable oil and alcohol must be substantially anhydrous and have a low free fatty acid content, because the presence of water or free fatty acid or both promotes soap formation. In this article, we examine different biodiesel sources (edible and nonedible), virgin oil versus waste oil, algae-based biodiesel that is gaining increasing importance, role of different catalysts including enzyme catalysts, and the current state-of-the-art in biodiesel production. JIMB 2008: BioEnergy—special issue.     

Production of algae-based biodiesel using the continuous catalytic Mcgyan® process

This study demonstrates the production of algal biodiesel from Dunaliella tertiolecta, Nannochloropsis oculata, wild freshwater microalgae, and macroalgae lipids using a highly efficient continuous catalytic process. The heterogeneous catalytic process uses supercritical methanol and porous titania microspheres in a fixed bed reactor to catalyze the simultaneous transesterification and esterification of triacylglycerides and free fatty acids, respectively, to fatty acid methyl esters (biodiesel). Triacylglycerides and free fatty acids were converted to alkyl esters with up to 85% efficiency as measured by 300 MHz ¹H NMR spectroscopy. The lipid composition of the different algae was studied gravimetrically and by gas chromatography. The analysis showed that even though total lipids comprised upwards of 19% of algal dry weight the saponifiable lipids, and resulting biodiesel, comprised only 1% of dry weight. Thus highlighting the need to determine the triacylglyceride and free fatty acid content when considering microalgae for biodiesel production.     

Efficient production of biodiesel from high free fatty acid-containing waste oils using various carbohydrate-derived solid acid catalysts

In the present study, such carbohydrate-derived catalysts have been prepared from various carbohydrates such as d-glucose, sucrose, cellulose and starch. The catalytic and textural properties of the prepared catalysts have been investigated in detail and it was found that the starch-derived catalyst had the best catalytic performance. The carbohydrate-derived catalysts exhibited substantially higher catalytic activities for both esterification and transesterification compared to the two typical solid acid catalysts (sulphated zirconia and Niobic acid), and gave markedly enhanced yield of methyl esters in converting waste cooking oils containing 27.8wt% high free fatty acids (FFAs) to biodiesel. In addition, under the optimized reaction conditions, the starch-derived catalyst retained a remarkably high proportion (about 93%) of its original catalytic activity even after 50 cycles of successive re-use and thus displayed very excellent operational stability. Our results clearly indicate that the carbohydrate-derived catalysts, especially the starch-derived catalyst, are highly effective, recyclable, eco-friendly and promising solid acid catalysts that are highly suited to the production of biodiesel from waste oils containing high FFAs.     

Biotechnological processes for biodiesel production using alternative oils

As biodiesel (fatty acid methyl ester (FAME)) is mainly produced from edible vegetable oils, crop soils are used for its production, increasing deforestation and producing a fuel more expensive than diesel. The use of waste lipids such as waste frying oils, waste fats, and soapstock has been proposed as low-cost alternative feedstocks. Non-edible oils such as jatropha, pongamia, and rubber seed oil are also economically attractive. In addition, microalgae, bacteria, yeast, and fungi with 20% or higher lipid content are oleaginous microorganisms known as single cell oil and have been proposed as feedstocks for FAME production. Alternative feedstocks are characterized by their elevated acid value due to the high level of free fatty acid (FFA) content, causing undesirable saponification reactions when an alkaline catalyst is used in the transesterification reaction. The production of soap consumes the conventional catalyst, diminishing FAME production yield and simultaneously preventing the effective separation of the produced FAME from the glycerin phase. These problems could be solved using biological catalysts, such as lipases or whole-cell catalysts, avoiding soap production as the FFAs are esterified to FAME. In addition, by-product glycerol can be easily recovered, and the purification of FAME is simplified using biological catalysts.     

Effects of water on biodiesel fuel production by supercritical methanol treatment

In the conventional transesterification of fats/vegetable oils for biodiesel production, free fatty acids and water always produce negative effects, since the presence of free fatty acids and water causes soap formation, consumes catalyst and reduces catalyst effectiveness, all of which result in a low conversion. The objective of this study was, therefore, to investigate the effect of water on the yield of methyl esters in transesterification of triglycerides and methyl esterification of fatty acids as treated by catalyst-free supercritical methanol. The presence of water did not have a significant effect on the yield, as complete conversions were always achieved regardless of the content of water. In fact, the present of water at a certain amount could enhance the methyl esters formation. For the vegetable oil containing water, three types of reaction took place; transesterification and hydrolysis of triglycerides and methyl esterification of fatty acids proceeded simultaneously during the treatment to produce a high yield. These results were compared with those of methyl esters prepared by acid- and alkaline-catalyzed methods. The finding demonstrated that, by a supercritical methanol approach, crude vegetable oil as well as its wastes could be readily used for biodiesel fuel production in a simple preparation.     

Conversion of Solid Organic Wastes into Oil via Boettcherisca peregrine (Diptera: Sarcophagidae) Larvae and Optimization of Parameters for Biodiesel Production

The feedstocks for biodiesel production are predominantly from edible oils and the high cost of the feedstocks prevents its large scale application. In this study, we evaluated the oil extracted from Boettcherisca peregrine larvae (BPL) grown on solid organic wastes for biodiesel production. The oil contents detected in the BPL converted from swine manure, fermentation residue and the degreased food waste, were 21.7%, 19.5% and 31.1%, respectively. The acid value of the oil is 19.02 mg KOH/g requiring a two-step transesterification process. The optimized process of 12∶1 methanol/oil (mol/mol) with 1.5% H₂SO₄ reacted at 70°C for 120 min resulted in a 90.8% conversion rate of free fatty acid (FFA) by esterification, and a 92.3% conversion rate of triglycerides into esters by alkaline transesterification. Properties of the BPL oil-based biodiesel are within the specifications of ASTM D6751, suggesting that the solid organic waste-grown BPL could be a feasible non-food feedstock for biodiesel production.     

An overview on the recent advances in the transesterification of vegetable oils for biodiesel production using chemical and biocatalysts

Biodiesel, chemically defined as monoalkyl esters of long chain fatty acids, are derived from renewable feed stocks like vegetable oils and animal fats. It is produced by both batch and continuous transesterification processes in which, oil or fat is reacted with a monohydric alcohol in the presence of a catalyst. The conventional method of producing biodiesel involves acid and base catalysts to form fatty acid alkyl esters. Downstream processing costs and environmental problems associated with biodiesel production and byproducts recovery have led to the search for alternative production methods and alternative substrates. Enzymatic reactions involving lipases can be an excellent alternative to produce biodiesel through a process commonly referred to as alcoholysis, a form of transesterification reaction or through an interesterification reaction. In order to increase the cost effectiveness of the process, the enzymes are immobilized using a suitable matrix. The use of immobilized lipases and whole cells may lower the overall cost, while presenting less downstream processing problems. Main focus of this paper is to discuss the important parameters that affect the biodiesel yield, various immobilization techniques employed, mechanisms and kinetics of transesterification reaction and the recent advances in continuous transesterification processes.     

Biodiesel production from Jatropha oil by catalytic and non-catalytic approaches: an overview

Biodiesel (fatty acids alkyl esters) is a promising alternative fuel to replace petroleum-based diesel that is obtained from renewable sources such as vegetable oil, animal fat and waste cooking oil. Vegetable oils are more suitable source for biodiesel production compared to animal fats and waste cooking since they are renewable in nature. However, there is a concern that biodiesel production from vegetable oil would disturb the food market. Oil from Jatropha curcas is an acceptable choice for biodiesel production because it is non-edible and can be easily grown in a harsh environment. Moreover, alkyl esters of jatropha oil meet the standard of biodiesel in many countries. Thus, the present paper provides a review on the transesterification methods for biodiesel production using jatropha oil as feedstock.     

Reactivity of triglycerides and fatty acids of rapeseed oil in supercritical alcohols

A catalyst-free biodiesel production method with supercritical methanol has been developed that allows a simple process and high yield because of simultaneous transesterification of triglycerides and methyl esterification of fatty acids. From these lines of evidence, we expected that similar results would be attained with the use of various alcohols by the supercritical treatment. However, it still remains unclear which type of reaction, transesterification or alkyl esterification, is faster. This parameter would be important in designing the optimum reaction conditions of the supercritical alcohol method. Therefore, we studied the effect of transesterification of triglycerides and esterification of fatty acids in rapeseed oil. Reaction temperature was set at 300 degrees C, and methanol, ethanol, 1-propanol, 1-butanol or 1-octanol was used as the reactant. The results showed that transesterification of triglycerides (rapeseed oil) was slower in reaction rates than alkyl esterification of fatty acids for any of the alcohols employed. Furthermore, saturated fatty acids such as palmitic and stearic acids had slightly lower reactivity than that of the unsaturated fatty acids; oleic, linoleic and linolenic.     

Esterification using a liquid lipase to remove residual free fatty acids in biodiesel

Lately, the price of liquid formulated lipase enzymes, usable in biodiesel production, has been significantly reduced. This enables one-time use of these enzymes for transesterification, and the process is used industrially. However, the process suffers a drawback by leaving 2−3 % free fatty acids in the crude biodiesel, which reduces the profitability. This article discusses a novel enzymatic FFA esterification reaction utilizing liquid lipase B from Candida antarctica (CALB) along with glycerol at low water concentrations to eliminate the residual FFA. The reaction setup was found able to reduce the free fatty acid concentration to within biodiesel specifications of < 0.25 wt.% FFA. Additionally, two alternative process setups are proposed, which were both found viable through a combination of experiments and simulations, and can be developed into full-scale processes. The resulting two-step enzymatic biodiesel process - transesterification followed by esterification - provides a potential process layout for the industrial production of biodiesel.     

Acid-catalyzed esterification of Zanthoxylum bungeanum seed oil with high free fatty acids for biodiesel production

A technique to produce biodiesel from crude Zanthoxylum bungeanum seed oil (ZSO) with high free fatty acids (FFA) was developed. The acid value of ZSO was reduced to 1.16mg KOH/g from 45.51mg KOH/g by only one-step acid-catalyzed esterification with methanol-to-oil molar ratio 24:1, H(2)SO(4) 2%, temperature 60 degrees C and reaction time 80min, which was selected as optimum for the acid-catalyzed esterification. During the acid-catalyzed esterification, FFA was converted into fatty acid methyl esters, which was confirmed by (1)H NMR spectrum. Compared with the other two-step pretreatment procedure, this one-step pretreatment can reduce the production cost of ZSO biodiesel. Alkaline-catalyzed transesterification converted the pretreated ZSO into ZSO biodiesel. The yield of ZSO biodiesel was above 98% determined by (1)H NMR spectrum. This study supports the use of crude ZSO as a viable and valuable raw feedstock for biodiesel production.     

脂肪酶催化合成生物柴油的研究

生物柴油是用动植物油脂或长链脂肪酸与甲醇等低碳醇合成的脂肪酸甲酯,是一种替代能源。这里探讨了生物法制备生物柴油的过程,采用脂肪酶酯化和酯交换两条工艺路线进行催化合成。深入研究制备过程中,不同脂肪酶、酶的用量和纯度、有机溶剂、低碳醇的抑制作用、吸水剂的作用、反应时间和进程、底物的特异性和底物摩尔比等参数对酯化过程的影响。试验结果表明,采用最佳酯化反应参数和分批加入甲醇并用硅胶作脱水剂的工艺过程,酯化率可以达到92％,经分离纯化后的产品GC分析的纯度可达98％以上,固定化酶的使用半衰期可达到360h。同时对酯交换制备生物柴油过程中,甲醇的用量和甲醇的加入方式对脂肪酶催化过程的影响作了初步研究,优化后的酯交换率可达到83％。     

Performance of heterogeneous ZrO2 supported metaloxide catalysts for brown grease esterification and sulfur removal

In order to achieve a viable biodiesel industry, new catalyst technology is needed which can process a variety of less expensive waste oils, such as yellow grease and brown grease. However, for these catalysts to be effective for biodiesel production using these feedstocks, they must be able to tolerate higher concentrations of free fatty acids (FFA), water, and sulfur. We have developed a class of zirconia supported metaloxide catalysts that achieve high FAME yields through esterification of FFAs while simultaneously performing desulfurization and de-metallization functions. In fact, methanolysis, with the zirconia supported catalysts, was more effective for desulfurization than an acid washing process. In addition, using zirconia supported catalysts to convert waste grease, high in sulfur content, resulted in a FAME product that could meet the in-use ASTM diesel fuel sulfur specification (<500 ppm). Possible mechanisms of desulfurization and de-metallization by methanolysis were proposed to explain this activity.     

Lipase-catalysed synthesis of ester oils from biodiesel by-products

Ester oils obtained from natural long-chain fatty acids and alcohols are versatile substitutes for many petroleum-based products. Their efficient synthesis with the solvent-free esterification of free fatty acids (FFA) from by-products of biodiesel fabrication and 2-ethyl-1-hexanol with immobilised lipase from Thermomyces lanuginosa was investigated. The immobilisation of the biocatalyst in static emulsion yielded a specific esterification activity that was higher by a factor of 4.9-9.4 than the activity of the native enzyme. Favourable properties of the silicone-based immobilisation matrix in terms of stability and immobilisation yield were observed. In biodiesel by-products, the immobilised lipase catalysed the esterification of FFA as well as the transesterification of residual fatty acid methyl esters (FAME) to the desired ester oils. A conversion of 90% FFA and 35% FAME gave a total yield of 60%. The inactivation coefficients during repeated use in a stirred-tank reactor with intermittent pressure reduction were exceptionally low.     

Lipase-catalysed synthesis of ester oils from biodiesel by-products

Ester oils obtained from natural long-chain fatty acids and alcohols are versatile substitutes for many petroleum-based products. Their efficient synthesis with the solvent-free esterification of free fatty acids (FFA) from by-products of biodiesel fabrication and 2-ethyl-1-hexanol with immobilised lipase from Thermomyces lanuginosa was investigated. The immobilisation of the biocatalyst in static emulsion yielded a specific esterification activity that was higher by a factor of 4.9–9.4 than the activity of the native enzyme. Favourable properties of the silicone-based immobilisation matrix in terms of stability and immobilisation yield were observed. In biodiesel by-products, the immobilised lipase catalysed the esterification of FFA as well as the transesterification of residual fatty acid methyl esters (FAME) to the desired ester oils. A conversion of 90% FFA and 35% FAME gave a total yield of 60%. The inactivation coefficients during repeated use in a stirred-tank reactor with intermittent pressure reduction were exceptionally low.     

Integrated enzymatic production of specific structured lipid and phytosterol ester compositions

Mixtures of specific structured lipids and phytosterol esters, valuable food components, were synthesized by an enzymatic one-pot process in organic-solvent-free medium starting from a mixture of phytosterol, caprylic acid and sunflower oil. Nine biocatalysts, seven commercially available lipases and two air-dried solid state (SSF) fermentation preparations of Aspergillus oryzae NRRL 6270 (AoSSF) and Aspergillus sojae NRRL 6271 (AsSSF), were screened for lipase activity in the transesterification reactions of sunflower oil with caprylic acid and for sterol esterase activity in the direct esterification of phytosterols with free fatty acids. The best process variant using a sequence of sterol esterase (AoSSF)-catalyzed esterification reaction of the free fatty acids and phytosterols, followed by water removal in vacuum and lipase-catalyzed transesterification with immobilized lipase from Rhizomucor miehei (Lipozyme) resulted in 92.1% conversion to phytosterol esters and 44.1% conversion to triacylglycerols containing two caprylic esters.     

Biomass productivity and productivity of fatty acids and amino acids of microalgae strains as key characteristics of suitability for biodiesel production

Microalgae are discussed as an alternative source for the production of biofuels. The lipid content compared to cultivation time of used species is the main reason for any choice of a special strain. This paper reviews more analytical data of 38 screened microalgae strains. After the cultivation period, total content of lipids was analysed. The extracted fatty acids were quantified as fatty acid methyl esters by GC analysis. The amino acids were analysed by HPLC. Chlorella sp., Chlorella saccharophila, Chlorella minutissima and Chlorella vulgaris were identified as species with the highest productivity of fatty acids relevant to transesterification reactions. The components were mainly linoleic acid, palmitic acid and oleic acid. To increase productivity of highly saturated fatty acids, cultivation parameters light intensity and temperature were varied. In this manner, the ideal conditions for biodiesel production were defined in this publication.     

Biodiesel production from algal oil using cassava (<Emphasis Type="Italic">Manihot esculenta</Emphasis> Crantz) as feedstock

As a potential source of biomass supplies, cassava (Manihot esculenta Crantz) has been studied for bioethanol production, but not for the production of biodiesel. In this study, we used cassava hydrolysate as an alternative carbon source for the growth of microalgae (Chlorella protothecoides) which accumulated oil in vivo, with high oil content up to 53% by dry mass under a 5-L scale fermentation condition. The oils were extracted and converted into biodiesel by transesterification. The biodiesel obtained consisted of mainly unsaturated fatty acids methyl ester (over 82%), cetane acid methyl ester, linoleic acid methyl ester, and oleic acid methyl ester. This work suggests the feasibility of an alternative choice for producing biodiesel from cassava by microalgae fermentation. We report herewith the optimized condition for the fermentation and for the hydrolysis of cassava as the carbon source.     

Moringa oleifera oil: a possible source of biodiesel

Biodiesel is an alternative to petroleum-based conventional diesel fuel and is defined as the mono-alkyl esters of vegetable oils and animal fats. Biodiesel has been prepared from numerous vegetable oils, such as canola (rapeseed), cottonseed, palm, peanut, soybean and sunflower oils as well as a variety of less common oils. In this work, Moringa oleifera oil is evaluated for the first time as potential feedstock for biodiesel. After acid pre-treatment to reduce the acid value of the M. oleifera oil, biodiesel was obtained by a standard transesterification procedure with methanol and an alkali catalyst at 60 degrees C and alcohol/oil ratio of 6:1. M. oleifera oil has a high content of oleic acid (>70%) with saturated fatty acids comprising most of the remaining fatty acid profile. As a result, the methyl esters (biodiesel) obtained from this oil exhibit a high cetane number of approximately 67, one of the highest found for a biodiesel fuel. Other fuel properties of biodiesel derived from M. oleifera such as cloud point, kinematic viscosity and oxidative stability were also determined and are discussed in light of biodiesel standards such as ASTM D6751 and EN 14214. The (1)H NMR spectrum of M. oleifera methyl esters is reported. Overall, M. oleifera oil appears to be an acceptable feedstock for biodiesel.     

The potential of restaurant waste lipids as biodiesel feedstocks

Biodiesel is usually produced from food-grade vegetable oils that are more expensive than diesel fuel. Therefore, biodiesel produced from food-grade vegetable oil is currently not economically feasible. Waste cooking oils, restaurant grease and animal fats are potential feedstocks for biodiesel. These inexpensive feedstocks represent one-third of the US total fats and oil production, but are currently devoted mostly to industrial uses and animal feed. The characteristics of feedstock are very important during the initial research and production stage. Free fatty acids and moisture reduce the efficiency of transesterification in converting these feedstocks into biodiesel. Hence, this study was conducted to determine the level of these contaminants in feedstock samples from a rendering plant. Levels of free fatty acids varied from 0.7% to 41.8%, and moisture from 0.01% to 55.38%. These wide ranges indicate that an efficient process for converting waste grease and animal fats must tolerate a wide range of feedstock properties.