Monitoring tablet surface roughness during the film coating process

The purpose of this study was to evaluate the change of surface roughness and the development of the film during the film coating process using laser profilometer roughness measurements, SEM imaging, and energy dispersive X-ray (EDX) analysis. Surface roughness and texture changes developing during the process of film coating tablets were studied by noncontact laser profilometry and scanning electron microscopy (SEM). An EDX analysis was used to monitor the magnesium stearate and titanium dioxide of the tablets. The tablet cores were film coated with aqueous hydroxypropyl methylcellulose, and the film coating was performed using an instrumented pilot-scale side-vented drum coater. The SEM images of the film-coated tablets showed that within the first 30 minutes, the surface of the tablet cores was completely covered with a thin film. The magnesium signal that was monitored by SEM-EDX disappeared after ∼15 to 30 minutes, indicating that the tablet surface was homogeneously covered with film coating. The surface roughness started to increase from the beginning of the coating process, and the increase in the roughness broke off after 30 minutes of spraying. The results clearly showed that the surface roughness of the tablets increased until the film coating covered the whole surface area of the tablets, corresponding to a coating time period of 15 to 30 minutes (from the beginning of the spraying phase). Thereafter, the film only became thicker. The methods used in this study were applicable in the visualization of the changes caused by the film coating on the tablet surfaces.     

Process Optimization of a Novel Immediate Release Film Coating System using QbD Principles

This work describes a quality-by-design (QbD) approach to determine the optimal coating process conditions and robust process operating space for an immediate release aqueous film coating system (Opadry® 200). Critical quality attributes (CQAs) or associated performance indicators of the coated tablets were measured while coating process parameters such as percent solids of the coating dispersion, coating spray rate, inlet air temperature, airflow rate and pan speed were varied, using a design of experiment protocol. The optimized process parameters were then confirmed by independent coating trials. Disintegration time of coated tablets was not affected by the coating process conditions used in this study, while tablet appearance, as determined by measurement of tablet color, coating defects and gloss was determined to be a CQA. Tablet gloss increased when low spray rate and low percent solids were used, as well as with increased coating pan speed. The study used QbD principles and experimental design models to provide a basis to identify ranges of coating process conditions which afford acceptable product quality. High productivity, color uniformity, and very low defect levels were obtained with Opadry 200 even when using a broad range of coating process conditions.     

Prediction of Tablet Film-coating Thickness Using a Rotating Plate Coating System and NIR Spectroscopy

The purpose of this research was to create a calibration model based on near-infrared (NIR) spectroscopy data obtained during a small-scale coating process to predict in-line the coating layer thickness of tablets coated in a side-vented drum coater. The developed setup for the small-scale coating process consisted of a rotating plate with 20 tablets molds that pass a spraying unit, a heating unit, and an in-line NIR spectroscopy probe during one rotation. High-density polyethylene (HDPE) was compressed to flat-faced tablets, and these were coated with a sustained release coating suspension containing Kollicoat IR and Kollicoat SR 30D. The film thickness of these tablets was determined for each tablet individually with a digital micrometer. A calibration model of predicted film thickness versus real-film thickness using PLS regression was developed. This model was tested against in-line NIR data obtained from a coating drum process, in which biconvex HDPE tablets were film-coated with the same film-coating suspension. The model predicted a final coating thickness of 240 μm, while the measured average thickness (n = 100 tablets) was 210 μm. Taking into account the use of a different setup and differently shaped tablets, it was possible to predict the coating thickness with accuracy comparable to the one of the digital micrometer. Thus, the small-scale rotating plate system was found to be an efficient means of preparing calibration model for a tablet-coating drum process.     

Optimization of Process Parameters for a Quasi-Continuous Tablet Coating System Using Design of Experiments

The aim of this study was to identify and optimize the critical process parameters of the newly developed Supercell quasi-continuous coater for optimal tablet coat quality. Design of experiments, aided by multivariate analysis techniques, was used to quantify the effects of various coating process conditions and their interactions on the quality of film-coated tablets. The process parameters varied included batch size, inlet temperature, atomizing pressure, plenum pressure, spray rate and coating level. An initial screening stage was carried out using a 2^6−1(IV) fractional factorial design. Following these preliminary experiments, optimization study was carried out using the Box–Behnken design. Main response variables measured included drug-loading efficiency, coat thickness variation, and the extent of tablet damage. Apparent optimum conditions were determined by using response surface plots. The process parameters exerted various effects on the different response variables. Hence, trade-offs between individual optima were necessary to obtain the best compromised set of conditions. The adequacy of the optimized process conditions in meeting the combined goals for all responses was indicated by the composite desirability value. By using response surface methodology and optimization, coating conditions which produced coated tablets of high drug-loading efficiency, low incidences of tablet damage and low coat thickness variation were defined. Optimal conditions were found to vary over a large spectrum when different responses were considered. Changes in processing parameters across the design space did not result in drastic changes to coat quality, thereby demonstrating robustness in the Supercell coating process.     

Characterization of tablet film coatings using a laser-induced breakdown spectroscopic technique

Laser-induced breakdown spectroscopy (LIBS) was evaluated as an early phase process analytical technology (PAT) tool for the rapid characterization of pharmaceutical tablet coatings. Measurement of coating thickness, uniformity, and photodegradation-predictive potential of the technique were evaluated. Model formulation tablets were coated with varying amounts (2%-4% wt/wt) of red and yellow Opadry II, and a pulsed laser was used to sample at multiple sites across the tablet face. LIBS was able to successfully detect the emissions of Fe and Ti in the coated samples, and a proportional increase in signal with coating thickness was observed. Batch-to-batch variability in the coating procedure was also easily monitored by LIBS. The coating thickness was non-uniform across the tablet surface with higher thickness at the edges, likely due to the concave shape of the tablet. Film coating levels and color of the film had been subjected to photostability studies according to the International Conference on Harmonisation (ICH) guideline to determine effectiveness of the film coats. LIBS measurements of coating thickness provided a good correlation (R (2) > 0.99) to photodegradation as measured by high-performance liquid chromatography (HPLC). Last, the concentration of Fe in the coating was varied and monitored by LIBS. Increasing photostability was observed with increasing levels of ferric oxide, providing a new understanding of the photoprotection mechanism in the coated formulation. Determination of levels of ferric oxide and coating thickness by LIBS demonstrated its utility as a good PAT tool for the determination of photoprotection of the drug, thereby enabling facile optimization of the coating process.     

Soluble Itraconazole in Tablet Form Using Disordered Drug Delivery Approach: Critical Scale-up Considerations and Bio-equivalence Studies

The present research work explores formulation design, critical scale-up considerations and bio-equivalence studies of soluble itraconazole (ITZ) in a tablet form using disordered drug delivery approach. Disordered system of ITZ with a lower viscosity grade of hydroxypropyl methyl cellulose (Pharmacoat 603) was developed for the first time and extensively characterised at three different stages, namely development of glass system, pellet coating and tablet compression using advanced analytical techniques. Complete molecular embedment of ITZ resulting in amorphisation was observed and found to be sustained until end of the real-time and accelerated stability studies. Developed formulation exhibited comparative in vitro dissolution profile (similarity factor >70) with reference product (Sporanox, Janssen Pharmaceutica) in simulated gastric fluid without enzymes. Formulation was scaled up in three batches (50,000 tablets/batch) with detailed validation of critical process parameters using process capability index method. Critical scale-up considerations like control of residual solvent content, effect of pellet size on dissolution, process variables in pellet coating, compressibility of coated pellets and cushioning effect required for desired compressibility were thoroughly discussed. Bioequivalence study of single dose of test and reference product in seven healthy human volunteers under fed condition exhibited significant bioequivalence with results (AUC_last and AUC_∞) lying between 90% confidence interval. With increase in number of subjects to 24, a significant effect on pharmacokinetic parameters of both reference as well as developed ITZ tablets was observed.     

Influence of Process Parameters on Tablet Bed Microenvironmental Factors During Pan Coating

Recent studies have shown the importance of monitoring microenvironmental conditions (temperature, relative humidity) experienced by the tablet bed during a pan coating process, thereby necessitating the need to understand how various process parameters influence these microenvironmental conditions. The process parameters studied in this work include exhaust air temperature, spray rate, inlet airflow rate, gun-to-bed distance, coating suspension percent solids, and atomization and pattern air pressure. Each of these process parameters was found to have an impact on the tablet bed relative humidity (RH), as measured using PyroButton data logging devices. A higher tablet bed RH was obtained with an increase in spray rate and atomization air pressure and with a decrease in exhaust air temperature, inlet airflow rate, gun-to-bed distance, suspension percent solids, and pattern air pressure. Based on this work, it can be concluded that the tablet bed thermodynamic conditions are a cumulative effect of the various process conditions. A strong correlation between the tablet bed RH and the frequency of tablet coating defect (logo bridging) was established, with increasing RH resulting in a higher percent of logo bridging events.     

A Novel Multi-Unit Tablet for Treating Circadian Rhythm Diseases

This study aimed to develop and evaluate a novel multi-unit tablet that combined a pellet with a sustained-release coating and a tablet with a pulsatile coating for the treatment of circadian rhythm diseases. The model drug, isosorbide-5-mononitrate, was sprayed on microcrystalline cellulose (MCC)-based pellets and coated with Eudragit^® NE30D, which served as a sustained-release layer. The coated pellets were compressed with cushion agents (a mixture of MCC PH-200/ MCC KG-802/PC-10 at a ratio of 40:40:20) at a ratio of 4:6 using a single-punch tablet machine. An isolation layer of OpadryII, swellable layer of HPMC E5, and rupturable layer of Surelease^® were applied using a conventional pan-coating process. Central-composite design-response surface methodology was used to investigate the influence of these coatings on the square of the difference between release times over a 4 h time period. Drug release studies were carried out on formulated pellets and tablets to investigate the release behaviors, and scanning electron microscopy (SEM) was used to monitor the pellets and tablets and their cross-sectional morphology. The experimental results indicated that this system had a pulsatile dissolution profile that included a lag period of 4 h and a sustained-release time of 4 h. Compared to currently marketed preparations, this tablet may provide better treatment options for circadian rhythm diseases.     

Study of coat quality of tablets coated by an on-line supercell coater

The aim of this study was to investigate the nature of Supercell coating, an on-line tablet coater that employed a unique pattern of airflow. Tablets coated at different spray rates (4, 6, 8, 10, and 12 mL/min) were analyzed to investigate the influence of different wetting conditions on the quality of coats formed. Scanning electron micrographs showed that tablet coats formed at a spray rate of 4 mL/min consisted of spray-dried droplets that did not coalesce. At a spray rate of 6 mL/min, surface roughness was found to be lower than at the other spray rates, and the coat appeared smoothest, whereby droplets seemed fused together. At higher spray rates, the droplets appeared as branching arms and scale-like structures. This was attributed to the spread of spray droplets by the processing air and mass transfer of wet coating materials between tablets. Further tests showed that coats formed at higher spray rates had higher drug yield, drug uniformity, color uniformity, and density. However, the variability in coat thickness was increased due to the mass transfer of coats and dissolution of tablet core surfaces by the coating material. Since coats of different characteristics can be formed in Supercell coating, the choice of wetting conditions would depend on the type of coat required and the coating materials used. Published: August 10, 2007     

Quantitative analysis of film coating in a pan coater based on in-line sensor measurements

A method was developed that enables in-line analysis of film coating thickness on tablets during a pan coating operation. Real-time measurements were made using a diffusereflectance near-infrared (NIR) probe positioned inside the pan during the coating operation. Real-time spectra of replicate batches were used for modeling film growth. Univariate analysis provided a simple method for in-line monitoring of the coating process using NIR data. An empirical geometric 2-vector volumetric growth model was developed, which accounts for differential growth on the face and band regions of biconvex tablets. The thickness of the film coat was determined by monitoring the decrease of absorption bands characteristic of a component of the tablet core and monitoring the increase of bands characteristic of a component in the coating material. There was good correlation between values estimated from the NIR data and the measured tablet volumetric growth. In-line measurements allow the coating process to be stopped when a predetermined tablet coating thickness is achieved. Published: September 20, 2005     

Optimization of an Aqueous Tablet-Coating Process Containing Carboxymethylated Cassia fistula Gum

The present investigation was aimed at developing and optimizing a simple aqueous tablet-coating formulation and its process. 5-Fluorouracil (5-FU) was used to ascertain the relative lipophilic/hydrophilic behavior of the coating system. Optimization was performed by evaluating the adhesive force strength and cohesive force strength of the tablet coat using a texture analyzer. The in vitro release of 5-FU was found to decrease with an increase in (tablet surface-coat) adhesive force strength. The (tablet-tablet) cohesive force strength was reduced by the addition of magnesium silicate to the coating solution. The addition of magnesium silicate (0.2% w/v) to the carboxymethyl Cassia fistula gum-chitosan (CCG-CH) coating surface significantly inhibited the release of 5-FU possibly due to an increase in the hydrophobic character of the coated tablet surface. This was possible by coating cohesive force strength reduction coating compositions (CCG-CH (70:30) and 0.3% magnesium silicate). Further, the FTIR-ATR and DSC analyses suggested the pivotal role of magnesium silicate in modifying the release of 5-FU from CCG-CH-coated tablets due to hydrogen bonding of its Si-O-Si or Mg-O groups with -OH moieties of CCG-CH.     

Fast Tablet Tensile Strength Prediction Based on Non-Invasive Analytics

In this paper, linkages between tablet surface roughness, tablet compression forces, material properties, and the tensile strength of tablets were studied. Pure sodium halides (NaF, NaBr, NaCl, and NaI) were chosen as model substances because of their simple and similar structure. Based on the data available in the literature and our own measurements, various models were made to predict the tensile strength of the tablets. It appeared that only three parameters—surface roughness, upper punch force, and the true density of material—were needed to predict the tensile strength of a tablet. Rather surprising was that the surface roughness alone was capable in the prediction. The used new 3D imaging method (Flash sizer) was roughly a thousand times quicker in determining tablet surface roughness than traditionally used laser profilometer. Both methods gave practically analogous results. It is finally suggested that the rapid 3D imaging can be a potential in-line PAT tool to predict mechanical properties of tablets in production.     

A Study on In-Line Tablet Coating—the Influence of Compaction and Coating on Tablet Dimensional Changes

Prior to coating, tablets are usually stored for a definite period to enable complete strain recovery and prevent subsequent volumetric expansion-related coating defects. In-line coating is defined as the coating of tablets immediately after compaction. In-line coating will be expected to improve manufacturing efficiencies. In this study, the possibility of in-line coating was studied by evaluating the influence of compaction and coating on tablet dimensional changes. The use of tapered dies for compaction was also evaluated. Two types of tablet coaters which presented different coating environments, namely the Supercell™ coater and pan coater, were employed for coating. The extent of tablet dimensional changes was studied in real time using optical laser sensors in a controlled environment. After compaction, tablet dimensional changes were found to be anisotropic. In contrast, coating resulted in isotropic volume expansion in both the axial and radial directions. Pan coating resulted in significantly greater tablet dimensional changes compared to Supercell™ coating. There was no significant difference in dimensional changes of tablets coated in line or after complete viscoelastic strain recovery for Supercell™ coating. However, significantly different dimensional changes were observed for pan coating. The use of tapered dies during compaction was found to result in more rapid viscoelastic strain recovery and also significantly reduced tablet dimensional changes when tablets were immediately coated after compaction using the pan coater. In conclusion, the Supercell™ coater appeared to be more suitable for in-line tablet coating, while tapered dies were beneficial in reducing tablet dimensional changes when the pan coater was employed for in-line coating.KEY WORDS: continuous manufacturing, in-line coating, tablet coating, tapered dies, viscoelastic strain recovery     

Rapid Assessment of Tablet Film Coating Quality by Multispectral UV Imaging

Chemical imaging techniques are beneficial for control of tablet coating layer quality as they provide spectral and spatial information and allow characterization of various types of coating defects. The purpose of this study was to assess the applicability of multispectral UV imaging for assessment of the coating layer quality of tablets. UV images were used to detect, characterize, and localize coating layer defects such as chipped parts, inhomogeneities, and cracks, as well as to evaluate the coating surface texture. Acetylsalicylic acid tablets were prepared on a rotary tablet press and coated with a polyvinyl alcohol-polyethylene glycol graft copolymer using a pan coater. It was demonstrated that the coating intactness can be assessed accurately and fast by UV imaging. The different types of coating defects could be differentiated and localized based on multivariate image analysis and Soft Independent Modeling by Class Analogy applied to the UV images. Tablets with inhomogeneous texture of the coating could be identified and distinguished from those with a homogeneous surface texture. Consequently, UV imaging was shown to be well-suited for monitoring of the tablet coating layer quality. UV imaging is a promising technique for fast quality control of the tablet coating because of the high data acquisition speed and its nondestructive analytical nature.     

Granulation by Roller Compaction and Enteric Coated Tablet Formulation of the Extract of the Seeds of <Emphasis Type="BoldItalic">Glinus Lotoides</Emphasis> Loaded on Aeroperl® 300 Pharma

The purpose of this research was to improve the hygroscopicity and poor flow properties of the crude dry extract of the seeds of Glinus lotoides and improve the disintegration time of the core-tablets for enteric coated formulation thereof. The liquid crude extract of the plant was adsorbed on granulated colloidal silicon dioxide (Aeroperl 300 Pharma) at 30% w/w and the dry extract preparation (DEP) was dry-granulated with roller-compaction using Micro-Pactor. Hygroscopicity, flow property and disintegration time were improved significantly due to the adsorption and granulation processes. Moreover, the DEP does not become mucilaginous even at higher relative humidity levels (above 65%). Oblong tablets (20 x 8.25 mm) containing 947 mg of the granulated DEP (equivalent to the traditional dose), 363 mg of Avicel PH101 and 90 mg of Ac-di-Sol as disintegrant were formulated using an instrumented eccentric tablet machine at 20 kN. The tablets showed a crushing strength of 195 N, a friability of 0.4% and disintegrated within 9 min. The tablets were then enteric coated using polymethacrylate co-polymers (Eudragit L 100-55 and Kollicoat MAE 100P). The coated tablets resisted disintegration or softening in simulated gastric fluid for a minimum of 2 h and disintegrated within 15 min in intestine simulated fluid at pH 6.8. In addition to controlling the release of the active agents, the enteric coating improved the strength and decreased friability of the core-tablets.     

Scale-up of a pan-coating process

The purpose of this work was to develop a practical scale-up model for a solvent-based pan-coating process. Practical scale-up rules to determine the key parameters (pan load, pan speed, spray rate, air flow) required to control the process are proposed. The proposed scale-up rules are based on a macroscopic evaluation of the coating process. Implementation of these rules does not require complex experimentation or prediction of model parameters. The proposed scale-up rules were tested by conducting coating scale-up and scale-down experiments on 24-inch and 52-inch Vector Hi-coaters. The data demonstrate that using these rules led to similar cumulative drug release profiles (f2≫50; and P Analysis of Variance [P _ANOVA]≫0.05 for cumulative percentage of drug released after 12 hours [Cum 12] from tablets made at 24- and 52-inch scales. Membrane characteristics such as opacity and roughness were also similar across the 2 scales. The effects of the key process variables on coat weight uniformity and membrane characteristics were also studied. Pan speed was found to be the most significant factor related to coating uniformity. Spray droplet size was found to affect the membrane roughness significantly, whereas opacity was affected by the drying capacity.     

A novel approach in the assessment of polymeric film formation and film adhesion on different pharmaceutical solid substrates

The purpose of this study was to evaluate the nature of film formation on tablets with different compositions, using confocal laser scanning microscopy (CLSM), and to measure film adhesion via the application of a novel “magnet probe test”. Three excipients, microcrystalline cellulose (MCC), spray-dried lactose monohydrate, and dibasic calcium phosphate dihydrate, were individually blended with 0.5% magnesium stearate, as a lubricant, and 2.5% tetracycline HCl, as a fluorescent marker, and were compressed using a Carver press. Tablets were coated with a solution consisting of 7% hydroxypropyl methylcellulose (HPMC) phthalate (HP-55), and 0.5% cetyl alcohl in acetone and isopropanol (11:9). The nature of polymer interaction with the tablets and coating was evaluated using CLSM and a designed magnet probe test. CLSM images clearly showed coating efficiency, thickness, and uniformity of film formation, and the extent of drug migration into the film at the coating interfaces of tablets. Among the excipients, MCC demonstrated the best interface for both film formation and uniformity in thickness relative to lactose monohydrate and dibasic calcium phosphate dihydrate. The detachment force of the coating layers from the tablet surfaces, as measured with the developed magnet probe test, was in the order of MCC>lactose monohydrate>dibasic calcium phosphate dihydrate. It was also shown that the designed magnet probe test provides reliable and reproducible results when used for measurement of film adhesion and bonding strength.     

Nondestructive and on-line monitoring of tablets using light-induced fluorescence technology

A system using light-induced fluorescence (LIF) technology was developed for rapid and nondestructive analysis of active pharmaceutical ingredients on tablet surfaces. Nonhomogenous tablets with defined layer of active ingredients were made by 3-Dimensional Printing technology to determine penetration depths of the light source and the resultant fluorescence responses. The LIF method of analysis showed penetration to depths of up to 3 mm into tablets. A correlation between LIF signals from analysis of tablet surfaces and the total drug content of the respective tablets was established. This method of surface analysis was verified with UV spectrometric methods for the total drug content of each respective tablet. The results from a small sample population of tablets made from both homogeneous and nonhomogeneous powder mixtures established good correlation between LIF surface monitoring and total tablet content. The use of on-line monitoring of the individual tablet for surface content demonstrated consistent LIF profiles from simulated production rates up to 3000 tablets a minute. The instrument was also field tested successfully on a tablet analyzer.     

Maintenance,equipment and operational improvements within an established Fermentation Pilot Plant

The Merck Research Laboratories' Fermentation Pilot Plant was constructed and commissioned in the early 1980's. It is a highly instrumented and automated facility which serves to maximize data collection for a variety of experimental batches. To continue successful and versatile operation as the facility ages, various improvements in equipment, maintenance, instrumentation, cleaning and sterility have been implemented. The goals were to improve flexibility, minimize down time, increase measurement accuracy and reduce contamination to enhance facility output for process development and clinical material production.The authors acknowledge the assistance of Ralph Calderone, Dennis Marshall, Thomas Hartnett, the mechanics and supervisors of the maintenance and instrumentation department, as well as the various vendors involved in these studies.     

Application of Quality by Design (QbD) Approach to Ultrasonic Atomization Spray Coating of Drug-Eluting Stents

The drug coating process for coated drug-eluting stents (DES) has been identified as a key source of inter- and intra-batch variability in drug elution rates. Quality-by-design (QbD) principles were applied to gain an understanding of the ultrasonic spray coating process of DES. Statistically based design of experiments (DOE) were used to understand the relationship between ultrasonic atomization spray coating parameters and dependent variables such as coating mass ratio, roughness, drug solid state composite microstructure, and elution kinetics. Defect-free DES coatings composed of 70% 85:15 poly(dl-lactide-co-glycolide) and 30% everolimus were fabricated with a constant coating mass. The drug elution profile was characterized by a mathematical model describing biphasic release kinetics. Model coefficients were analyzed as a DOE response. Changes in ultrasonic coating processing conditions resulted in substantial changes in roughness and elution kinetics. Based on the outcome from the DOE study, a design space was defined in terms of the critical coating process parameters resulting in optimum coating roughness and drug elution. This QbD methodology can be useful to enhance the quality of coated DES.KEY WORDS: biodegradable polymers, coating, drug-eluting stents, processing, quality by design