首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 15 毫秒
1.
Halloysite/potato starch composites were prepared by adding modified natural halloysite nanotubes into potato starch matrices to reenforce the mechanical properties of potato starch films. The halloysite/potato starch films were characterized by X-ray diffraction, scanning electron microscope and infrared spectrometry. Meanwhile, the mechanical properties and transparency of the films were studied. The results show that the modified halloysite nanotubes can be well distributed in the starch matrix and thus the tensile strength of the films was clearly enhanced. The flexibility of the films could be improved through adding glycerol although at the cost of reducing tensile strength. But incorporation of PVA could further improve the tensile strength of the halloysite/potato starch films.  相似文献   

2.
The proposal in this study was to evaluate the physical properties of different biopolymers films. The materials used were: pectin, carboxyl methylcellulose, methylcellulose, hydroxyl propylcellulose, hydroxypropyl-methylcellulose, and corn waxy starch; from these polysaccharides aqueous dispersions were prepared to 3% (w/v) for obtained films. In these biopolymer films, the thermal diffusivities (α) was evaluated by the Open Photoacoustic Cell method; also, their mechanical properties as tensile strength, elongation, and Young’s modulus were measured, their crystallinity percentage was evaluated by X-ray diffraction and microstructure through atomic force microscopy in contact mode. From the polysaccharide films, it was observed that most of them were flexible and transparent. In the case of the films, mechanical properties were found that the highest value of tensile strength and Young’s modulus corresponded to carboxyl methylcellulose with 69.17 and 1,912.20 MPa values, respectively. Also, Open Photoacoustic Cell method and X-ray diffraction measurements showed that there exist a correlation between the thermal diffusivity values and the crystallinity measured in the biopolymer films. It was also observed that α values of cellulose derived was affected by the substitution group in the molecule, reaching the highest α value, the films of carboxyl methylcellulose. Regarding the microstructural of the films, starch showed the highest roughness value (88.6 nm) whereas hydroxypropyl-methylcellulose resulted with the lowest roughness value (7.67 nm).  相似文献   

3.
Bacterial polyesters have attracted much attention as biodegradable biocompatible polymers. Poly-3-hydroxybutyrate, a microbially produced thermoplastic, has similar material properties to polypropylene. Its potential application as biodegradable and biocompatible plastics is well documented. However, due to high cost it is used mainly in biomaterials for medical applications. Materials with useful properties may result from blending bacterial polyhydroxybutyrate (PHB) with other polymers. In this paper, the compatibility of PHB with starch for improved properties and cost reduction is discussed. The thermal and mechanical properties of the blended films were studied by means of thermogravimetry, differential scanning calorimetry and an automated material testing system. The results revealed that blend films had a single glass transition temperature for all the proportions of PHB:starch tested. The nature of all combinations was found to be crystalline. The tensile strength was optimum for the PHB:starch ratio of 0.7:0.3 (wt/wt). The variation in tensile strength, Young's modulus, extension needed to break, thermal stability, glass transition temperature, melting temperature, for the different proportions of PHB:starch are discussed.  相似文献   

4.
The effects of hydrophilic and hydrophobic characteristics of proteins on the interactions with corn starch were investigated in this study. The model system included corn starch and proteins, i.e. zein, gliadin, gluten, soy protein and rapeseed protein. The blend films were prepared by thermo-moulding in gentle conditions at 70 °C in order to avoid starch gelatinization, with respect to water content, and avoid protein denaturation. The effects of different kinds of proteins on structure and mechanical behaviour of blend biomaterials were characterised by scanning electron microscopy (SEM) and tensile test, respectively. The effects of different kinds of proteins on intermolecular interactions between proteins and starch were investigated by dynamical mechanical thermal analysis. Based on the solubility measurement results, almost all protein films showed the similar solubility to the natural protein powders, resulting from the weak influence of mild thermo-moulding treatment on protein inner structure. Different morphologies were observed for different proteins and corresponding blends, which are relatively loose protein architecture that appeared for hydrophobic protein and blend films, and uniform and densely packed architecture for hydrophilic ones. Moreover, different mechanical behaviours were obtained for different proteins and corresponding blends. No significantly increased strength for hydrophilic protein blends with starch added can be explained that there is weak intermolecular interaction between both components based on SEM observation. However, the addition of corn starch granules in hydrophobic protein networks was assumed that starch destroyed or weakened the protein network, resulting in the decrease of mechanical strength.  相似文献   

5.
BACKGROUND AND AIMS: Leaf mechanical properties, which are important to protect leaves against physical stresses, are thought to change with light and nutrient availabilities. This study aims to understand phenotypic changes of leaf mechanical properties with respect to dry mass allocation and anatomy. METHODS: Leaf lamina strength (maximum force per unit area to fracture), toughness (work to fracture) and stiffness (resistance against deformation) were measured by punch-and-die tests, and anatomical and physiological traits were determined in Plantago major plants grown at different light and nutrient availabilities. A conceptual approach was developed by which punch strength and related carbon costs can be quantitatively related to the underlying anatomical and morphological traits: leaf thickness, dry-mass allocation to cell walls and cell-wall-specific strength. KEY RESULTS: Leaf lamina strength, toughness and stiffness (all expressed on a punch area basis) increased with light availability. By contrast, nutrient availability did not change strength or toughness, but stiffness was higher in low-nutrient plants. Punch strength (maximum force per unit punch area, F(max)/area) was analysed as the product of leaf mass per area (LMA) and F(max)/leaf mass (= punch strength/LMA, indicating mass-use efficiency for strength). The greater strength of sun leaves was mainly explained by their higher LMA. Shade leaves, by contrast, had a higher F(max)/leaf mass. This greater efficiency in shade leaves was caused by a greater fraction of leaf mass in cell walls and by a greater specific strength of cell walls. These differences are probably because epidermis cells constitute a relatively large fraction of the leaf cross-section in shaded leaves. Although a larger percentage of intercellular spaces were found in shade leaves, this in itself did not reduce 'material' strength (punch strength/thickness); it might, however, be important for increasing distance between upper and lower epidermis per unit mass and thus maintaining flexural stiffness at minimal costs. CONCLUSIONS: The consequences of a reduced LMA for punch strength in shaded leaves was partially compensated for by a mechanically more efficient design, which, it is suggested, contributes importantly to resisting mechanical stress under carbon-limited conditions.  相似文献   

6.
Extrusion of pectin/starch blends plasticized with glycerol   总被引:5,自引:0,他引:5  
The microstructural and thermal dynamic mechanical properties of extruded pectin/starch/glycerol (PSG) edible and biodegradable films were measured by scanning electron microscopy (SEM) and thermal dynamic mechanical analysis (TDMA). SEM revealed that the temperature profile (TP) in the extruder and the amount of water present during extrusion could be used to control the degree to which the starch was gelatinized. TDMA revealed that moisture and TP during extrusion and by inference the amount of starch gelatinization had little effect on the mechanical properties of PSG films. Furthermore, TDMA revealed that PSG films underwent a glass transition commencing at about −50°C and two other thermal transitions above room temperature. Finally, it was concluded that the properties of extruded PSG films were comparable to those cast from solution.  相似文献   

7.
The aim of this study was to characterize chayotextle starch films reinforced with cellulose (C) and cellulose nanoparticle (CN) (at concentrations of 0.3%, 0.5%, 0.8% and 1.2%), using thermal, mechanical, physicochemical, permeability, and water solubility tests. C was acid-treated to obtain CN. The films were prepared by casting; potato starch and C were used as the control. The solubility of the starch films decreased with the addition of C and CN compared with its respective film without C and CN. No statistical difference (α = 0.05) was found in the films added with different concentrations of C and CN. In general, the mechanical properties were improved with the addition of C and CN, and higher values of tensile strength and elastic modulus were determined in the films reinforced with CN. The melting temperature and enthalpy increased with the addition of C and CN, and the values of both thermal parameters were higher in the films with CN than with C; the enthalpy value of the film decreased when the concentration of C or CN increased in the composite. Low concentration of C and CN is better distributed in the matrix film. The addition of C and CN in the starch films improved some mechanical, barrier, and functional properties.  相似文献   

8.
Microstructural and mechanical properties of extruded pectin and glycerol films with various combinations of orange albedo and starch were determined by universal mechanical testing (UMT), dynamic mechanical analysis (DMA), optical microscopy (OM) and scanning electron microscopy (SEM). A glass transition and a second order transition attributed to the onset of translational motion of the pectin molecules was observed in all films. Observation by OM suggested that extrusion in the presence of dilute HCl was more effective in disintegrating albedo than either water or dilute citric acid. UMT, DMA and SEM analysis revealed that extruded pectin/albedo/starch/glycerol films provided better mechanical properties than pectin/albedo/glycerol films and were comparable in mechanical properties to extruded pectin/starch/glycerol films.  相似文献   

9.
The material compositions and the technological procedures to prepare biodegradable films with the film blowing technology based on thermoplastic starch were studied in this work. The activities were focused on the analysis of the effects of starch source (maize, potato and wheat), supplier (Roquette, Cerestar and Cameo) and the type of plasticizers (glycerol, urea and formamide) and their content on the physical–chemical and mechanical properties. Moreover, in order to develop a film blowing technology, material composition as well as processing condition were optimized. Among 10 varieties of thermoplastic starch prepared, the combination of urea and formamide as plasticizer restrained retrogradation and improved mechanical properties. Extensional rheological properties of the thermoplastic starch films were also investigated: the results showed that the occurrence of strain-hardening behaviour in some of the investigated compositions lead to a positive effect on the film blowing process. In this study we found that the combination of high-amylose (>51%) starch and urea/formamide mixtures as plasticizer produced an homogenous film of a 50 μm thickness and a robust film blowing process due to the good elongational viscosity, high deformability of the melt and strain-hardening behaviour.  相似文献   

10.
Starch films were developed from oxidized potato starch (OPS) with glycerol as a plasticizer at different contents. The OPS films were transparent and flexible. The mechanical properties of these films were measured, and the results indicated that the film with 19.4% glycerol exhibited the desirable mechanical properties. X-ray diffraction study showed that the increase of glycerol content led to a decrease in the crystallinity for OPS films, and storage conditions such as storage time, storage temperature and relative humidity also had certain effects on the retrogradation of starch owing to re-crystallization. Anti-leakage, anti-crosslinking, and stability in acid or alkali solutions of the OPS films were also studied, and the results indicated that the OPS films had excellent anti-leakage ability for vegetable oil, good anti-crosslinking ability in saturated formaldehyde vapor, and good stability in acid aqueous medium, but poor stability in alkali aqueous medium.  相似文献   

11.
Oxidized and acetylated corn starch-based films were prepared by casting with glycerol as a plasticizer. The present study investigated the effects of extrusion prior to film-making and glycerol content on the properties of starch films. The films with extrusion exhibited lower tensile strength, higher elongation at break, higher water vapor permeability and higher oil permeability than those without extrusion. Extrusion reduced heat sealability of the films. With the increase of glycerol content, the films became more flexible with higher elongation at break and lower tensile strength. Water vapor permeability, oil permeability and the range between the onset temperature and the melt peak temperature rose as glycerol content increased. The thermograms indicated that plasticizers and biopolymers were compatible. These results suggested that extrusion did no good to starch films while glycerol content had apparent effect on the mechanical and barrier properties of the films.  相似文献   

12.
Preparation and characterization of surface crosslinked TPS/PVA blend films   总被引:1,自引:0,他引:1  
Surface crosslinked thermoplastic starch (TPS)/PVA blend films were prepared by applying ultra violet (UV) irradiation. Sodium benzoate was used as photosensitizer and induced onto film surface layer by soaking the TPS/PVA films in the photosensitizer aqueous solution. The effects of concentration of photosensitizer aqueous solution, soaking time and UV irradiation dose on the surface photocrosslinking reaction were investigated. Physical properties, such as water contact angle, moisture absorption, swelling degree and solubility in water as well as mechanical properties of the films were measured to characterize the influence of the surface photocrosslinking modification. The obtained results showed that the surface modification considerably reduced the surface hydrophilic character of the TPS/PVA films, enhanced the film’s water resistance and also increased tensile strength and Young’s modulus but decreased elongation at break of the films.  相似文献   

13.
The need to replace conventional polymers due to environmental pollution caused by them has led to increased production of biodegradable polymers such as starch. Thus, the application possibilities of starch have increased. In this study, we produced and characterized biodegradable films derived from native and oxidized potato starch. The film-forming solution was prepared with different concentrations of extracted starch (native or oxidized) and a plasticizer (glycerol or sorbitol). Then, the mechanical, barrier, morphological, and structural properties of the films were characterized. The moisture content of the films varied from 15.35?±?1.31 to 21.78?±?0.49%. The elastic modulus of the films ranged from 219?±?14.97 to 2299?±?62.91 MPa. The film of oxidized starch plasticized with sorbitol in the lowest content was the most resistant and flexible; moreover, this film also presented lower water vapor permeability and low solubility in water. Fourier-transform infrared spectroscopic analysis of the biodegradable films indicated the presence of same functional groups as those of starch with bands in the same regions. The film thickness was lower for the films plasticized with glycerol whereas the color variation (Δ?) was lower for the ones plasticized with sorbitol. In case of both plasticizers, the increase in their content decreased the Δ? value. All the biodegradable films presented stability against water absorption owing to their low solubility in water. Morphological evaluation revealed the presence of partially gelatinized starch granules in the films. The roughness parameter (Rq) of the films varied from 3.39 to 10.9 nm, indicating that their surfaces are smooth. X-ray diffraction studies showed a B-type pattern for the starches, which is representative of tubers. Further, the films present higher relative crystallinity (RC) compared to the starches. The biodegradable starch films are uniform, transparent and with low solubility in water. The oxidation of starch and use of sorbitol as a plasticizer resulted in improved properties of the starch films, which is suitable for application.  相似文献   

14.
Strong correspondence between the uniaxial apparent strength and stiffness of cancellous bone allows the use of stiffness as a predictor of bone strength. Measured values of mechanical properties in cancellous bone can be different between experiments due to different experimental conditions. In the current study, bone volume fraction, experimentally determined and finite element (FE) predicted stiffness were examined as predictors of cancellous bone ultimate strength in two different groups each of which was tested using a different end constraint. It is demonstrated that, although always significant, the relationships of strength with bone volume fraction and experimentally determined stiffness are different between test groups. Apparent stiffness, estimated by FE modeling, predicts the ultimate strength of human cancellous bone consistently for all examined experimental protocols.  相似文献   

15.
Biomechanical tests of human femora have shown that small variations of the loading direction result in significant changes in measured bone mechanical properties. However, the heterogeneity in geometrical and bone tissue properties does not make human bones well suited to reproducibly assess the effects of loading direction on stiffness and strength. To precisely quantify the influence of loading direction on stiffness and strength of femora loaded at the femoral head, we tested femora from C57BL/6 inbred mice. We developed an image-based alignment protocol and investigated the loading direction influence on proximal femur stiffness and strength. An aluminum femoral phantom and C57BL/6 femora were tested under compression with different loading directions. Both tests, with the aluminum phantom and the murine bones, showed and quantified the linear dependence of stiffness on loading direction: a 5 degrees change in loading direction resulted in almost 30% change in stiffness. Murine bone testing also revealed and quantified the variation in strength due to loading direction: 5 degrees change in loading direction resulted in 8.5% change in strength. In conclusion, this study quantified, for the first time, the influence of misalignment on bone stiffness and strength for femoral head loading. We showed the extreme sensitivity of this site regarding loading direction.  相似文献   

16.
Films formed by blending of two polymers usually have modified physical and mechanical properties compared to films made of the individual components. Our preliminary studies indicated that incorporation of chitosan in polyethylene oxide (PEO) films may provide additional functionality to the PEO films and may decrease their tendency to spherulitic crystallization. The objective of this study was to determine the correlation between chitosan/PEO weight ratio and the physical, mechanical, and antibacterial properties of corresponding films. Films with chitosan/PEO weight ratios from 100/0 to 50/50 in 10% increments were characterized by measuring thickness, puncture strength (PS), tensile strength (TS), elongation at break (%E), water vapor permeability (WVP), and water solubility (WS). Additionally, the films were examined by polarized microscopy, wide-angle X-ray diffraction (WAXD), and Fourier transform infrared (FTIR) spectroscopy, and their antibacterial properties were tested against Escherichia coli. The chitosan fraction contributes to antimicrobial effect of the films, decreases tendency to spherulitic crystallization of PEO, and enhances puncture and tensile strength of the films, while addition of the PEO results in thinner films with lower water vapor permeability. Films with 90/10 blend ratio of chitosan/PEO showed the most satisfactory PS, TS, %E, and antibacterial properties of all tested ratios.  相似文献   

17.
Cross-linked high amylose starch cast films were prepared to study the effect of cross-linking degree on various properties in normal environmental conditions. Mechanical tensile properties (Young's modulus, elongation at break, tensile strength), water vapour transmission rate (WVTR) and oxygen permeability coefficients of cast films were determined as a function of cross-linking degree and percentage of free humidity. Cross-linking degree and degree of crystallinity are closely related and seem to have non-negligible opposite effect on the properties of interest. By using increased amounts of cross-linking agents, the effect of cross-linking degree tends to reduce the degree of crystallinity modulating thus mechanical properties, water vapour permeability and oxygen permeability coefficients. Yield strength, tensile strength at break, WVTR versus cross-linking degree showed a non-monotonous behaviour. Maximal values for these properties were reached for moderate cross-linking degree. Optimal crystalline/amorphous ratio in the films may induce interactions and balanced effects, which would be responsible for the non-linear behaviour of some of the investigated properties. By cross-linking with epichlorohydrin in the range 1–10 g crosslinker/100 g polymer, the mechanical properties of films are still related to water content and water vapour permeability remains high compared to some synthetic polymeric materials.  相似文献   

18.
Polymer films of sago starch/polyvinyl alcohol (PVA) were prepared by casting and cured under ultra violet (UV) radiation. Different blends were made varying the concentration of sago starch and PVA. Tensile strength (TS) and elongation at break (Eb) of the prepared films were studied. Films made up of sago starch and PVA with a ratio of 1:2 showed the highest TS and Eb. The physico-mechanical properties of prepared films were improved by grafting with acrylic monomers with the aid of UV radiation. A series of formulations was prepared with two monomers 2-ethyl 2-hydroxymethyl 1,3 methacrylate (EHMPTMA) and 2-ethylhexylacrylate (EHA) and a photoinitiator. Monomer concentration, soaking time and radiation dose were optimized in terms of grafting and mechanical properties. The highest TS was at 50% EHMPTMA and 48% EHA and 2% photo initiator at 5 min soaking time and recorded value was 6.58 MPa. The prepared films were further characterized with NMR spectroscopy and scanning electron microscope (SEM).  相似文献   

19.
Shogren R 《Biomacromolecules》2007,8(11):3641-3645
The effect of orientation on the properties of amylose and starch films was studied in order to determine if film strength, flexibility, and water resistance could be improved. Potato amylose and high (70%) amylose corn starch were peracetylated, cast into films, stretched in hot glycerol 1-6 times the original length, and deacetylated. Molecular orientation of potato amylose films was much higher than for high-amylose corn starch films as determined by optical birefringence. For potato amylose films, orientation resulted in large increases in tensile strength and elongation but little change in modulus. For high-amylose corn starch films, tensile strength and modulus did not change with draw ratio but elongation to break increased from about 8% to 27% as draw ratio increased from 1 to 5. Scanning electron micrographs revealed many small crazes in the drawn starch films, suggesting that the improved film toughness was due to energy dissipation during deformation of the crazes. Annealing of drawn films at 100% humidity resulted in partial crystallization and improved wet strength.  相似文献   

20.
Starch/poly(vinyl alcohol) (PVA) films were prepared with calcium chloride (CaCl(2)) as the plasticizer. The micro morphology of pure starch/PVA film and CaCl(2) plasticized starch/PVA film was observed by scanning electron microscope. The interaction between CaCl(2) and starch/PVA molecules was investigated by Fourier transform infrared spectroscopy. The influence of CaCl(2) on the crystalline, thermal and mechanical properties of starch/PVA films was studied by X-ray diffraction, differential scanning calorimetry, thermogravimetric analysis, and tensile testing, respectively. The results indicated that CaCl(2) could interact with starch and PVA molecules and then effectively destroy the crystals of starch and PVA. Starch/PVA films plasticized with CaCl(2) became soft and ductile, with lower tensile strength and higher elongation at break compared with pure starch/PVA film. The water content of starch/PVA film would increase with the addition of CaCl(2). This is an important cause of the plasticization of CaCl(2) on starch/PVA film.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号