Superficially Porous Particle Based Hydroxypropyl‐β‐cyclodextrin Stationary Phase for High‐Efficiency Enantiomeric Separations

A superficially porous particle (SPP)‐based hydroxypropyl‐β‐cyclodextrin (HPBCD) chiral stationary phase (CSP) was produced and its chromatographic performance was compared to both 5 µm and 3 µm fully porous particle (FPP)‐based CSPs. The relative surface coverage of the HPBCD chiral selector on each particle was approximately equal, which resulted in equivalent enantiomeric selectivity (α) values on each phase when constant mobile phase conditions were used. Under such conditions, the SPP column resulted in greatly reduced analysis times and three times greater efficiencies compared to the FPP columns. When higher flow rates were used, efficiency gains per analysis times were five times greater for the SPP column compared to the FPP‐based columns. When the mobile phases were altered to give similar analysis times on each column, resolution values were doubled for the SPP column. Finally, the novel SPP based HPBCD column proved to be stable for 500 injections under high flow rate (4.5 mL/min) and high pressure (400 bar) conditions used for an ultrafast (~45 sec) enantiomeric separation. Chirality 27:788–794, 2015. © 2015 Wiley Periodicals, Inc.     

Evaluation of the specific intermolecular interactions responsible for chiral selectivity for phenylalanine analogs in subcritical fluid chromatography

A set of phenyl ring‐substituted N‐t‐butoxycarbonyl‐phenylalanine analogs were chirally resolved using an α‐Burke 2 Pirkle‐type chiral column under subcritical fluid conditions. Various mobile phase modifiers were used to elute the chiral analytes, resulting in different selectivity factors for each analog. The observed selectivity factors were accurately modeled based on the bulk solvation parameters for each mobile phase modifier. The resulting model equation was used to predict the selectivity factors using an additional modifier not included in the model building data set. The predictive ability of the model was demonstrated to be quite good for this limited range of analogs and mobile phase modifiers. Chirality 11:98–102, 1999. © 1999 Wiley‐Liss, Inc.     

Resolution and determination of enantiomeric purity of the enantiomers of felodipine using chiral-AGP® as stationary phase

A direct chiral chromatographic reversed phase method for the determination of the enantiomers of felodipine is described. The influence of charged and uncharged modifiers as well as the effect of the mobile phase pH on the enantiomeric resolution is discussed. A high mobile phase pH and the addition of 2-propanol as organic modifier gave the highest separation factor (α = 1.3). The high mobile phase pH (pH = 7.6) is outside the recommended pH limit of silica based columns but was necessary to achieve baseline resolution of (R)- and (S)-felodipine. Improvement of column efficiency by increasing column temperature was utilized for optimization of the enantiomeric resolution (Rs = 1.7). The enantiomers of felodipine and three related compounds were separated within 15 min. The enantiomeric purity of (R)- and (S)-felodipine in injections and (R)-felodipine in bulk substance was higher than 99.5% and no racemization was observed after storage at accelerated conditions. A poor Chiral-AGP® column used for a long period was restored using a simple wash step together with repacking the top of the chromatographic column. © 1995 Wiley-Liss, Inc.     

Enantiomeric separation of imidazolinone herbicides using chiral high-performance liquid chromatography

Chiral high-performance liquid chromatography (HPLC) is one of the most powerful tools to prepare enantiopure standards of chiral compounds. In this study, the enantiomeric separation of imidazolinone herbicides, i.e., imazethapyr, imazapyr, and imazaquin, was investigated using chiral HPLC. The enantioselectivity of Chiralpak AS, Chiralpak AD, Chiralcel OD, and Chiralcel OJ columns for the three analytes was compared under similar chromatographic conditions. Chiralcel OJ column showed the best chiral resolving capacity among the test columns. The resolved enantiomers were distinguished by their signs of circular dichroism detected at 275 nm and their structures confirmed with LC-mass spectrometric analysis. Factors affecting the chiral separation of imidazolinones on Chiralcel OJ column were characterized. Ethanol acted as a better polar modifier than the other alcohols including 2-propanol, 1-butanol, and 1-pentanol. Although the acidic modifier in the mobile phase did not influence chiral recognition, it was necessary for reducing the retention time of enantiomers and suppressing their peak tailing. Thermodynamic evaluation suggests that enantiomeric separation of imidazolinones on Chiralcel OJ column is an enthalpy-driven process from 10 to 40 degrees C. This study also shows that small amounts of pure enantiomers of imidazolinones may be obtained by using the analytical chiral HPLC approach.     

Study on the HPLC‐based separation of some ezetimibe stereoisomers and the underlying stereorecognition process

The enantioseparation of ezetimibe stereoisomers by high‐performance liquid chromatography on different chiral stationary phases, ie, 3 polysaccharide‐based chiral columns, was studied. It was observed that cellulose‐based Chiralpak IC column exhibited the best resolving ability. After the optimization of mobile phase compositions in both normal and reversed phase modes, satisfactory separation could be obtained on Chiralpak IC column, especially in normal phase mode. The use of prohibited solvents as nonstandard mobile phase gave rise to better resolution than that of standard mobile phases (n‐hexane/alcohol system). In addition, the presence of ethanol in nonstandard mobile phase has played an important role in enhancing chromatographic efficiency and resolution between ezetimibe stereoisomers. Various attempts were made to comprehensively compare the chiral recognition capabilities of immobilized versus coated polysaccharide‐based chiral columns, amylose‐based versus cellulose‐based chiral stationary phases, reversed versus normal phase modes, and standard versus nonstandard mobile phases. Moreover, possible solute‐mobile phase‐stationary phase interactions were derived to explain how stationary and mobile phases affected the separation. Then the method validation with respect to selectivity, linearity, precision, accuracy, and robustness was carried out, which was demonstrated to be suitable and accurate for the quantitative determination of (RRS)‐ezetimibe impurity in ezetimibe bulk drug.     

Manipulation of chiral resolution for isoxazoline-based IIb/IIIa receptor antagonists using various mobile phase additives in subcritical fluid chromatography

Subcritical fluid chromatography (SubFC) using a carbon dioxide-methanol mobile phase is used for the chiral resolution of IIb/IIIa receptor antagonist enantiomers. The chiral resolution of three analogs, each containing two chiral centers, is optimized using various mobile phase additives. The effects that acidic, basic, and neutral additives have on retention, efficiency, and resolution are examined. The additive that gives the best resolution was found to be dependent upon the functionality and charge of the chiral analyte. For charged analytes, additives that act as competing ions of the same charge as the chiral analyte dramatically improve efficiency and resolution. Resolution of neutral chiral analyte enantiomers is also greatly affected by the choice of mobile phase additive. Chirality 10:338–342, 1998. © 1998 Wiley-Liss, Inc.     

Chiral separation of aliphatic primary amino alcohols as o‐phthaldialdehyde/mercaptoethanol derivatives on polysaccharide‐based chiral stationary phases

A sensitive chiral high performance liquid chromatography (HPLC) method for the determination of aliphatic primary amino alcohol isomers with o‐phthaldialdehyde/mercaptoethanol precolumn derivatization has been developed and validated. Seven chiral columns were tested in a reversed phase mode. Excellent enantioseparation with the resolution more than 2.0 was achieved on Chiralcel OJ‐3R. The effect of various chromatographic conditions including column temperature, acetonitrile content in the mobile phase, buffer pH, buffer concentration, and buffer type in the mobile phase on the retention and the selectivity was investigated. The final mobile phase consisted of binary mixture of 20mM ammonium formate solution with acetonitrile (75:25; v/v). The analyses were performed at mobile phase flow rate of 1.0 mL/min and the column temperature of 40°C. The fluorescence detection was performed at excitation wavelength of 345 nm and emission wavelength of 450 nm. The developed method was fully validated in terms of linearity, sensitivity, accuracy, precision, intermediate precision, and selectivity according to International Council for Harmonisation of Technical Requirements for Pharmaceuticals for Human Use guidelines using internal normalization procedure. The proposed chiral method was proved to be highly sensitive, simple, and rapid and was successfully applied to the determination of D‐Valinol content in commercially available samples of L‐Valinol.     

Use of a naphthylethylcarbamoylated-β-cyclodextrin chiral stationary phase for the separation of drug enantiomers and related compounds by sub- and supercritical fluid chromatography

Enantiomeric separation of a variety of drugs and related compounds was achieved on an (S)-naphthylethylcarbamoylated-β-cyclodextrin (S-NEC-CD) chiral stationary phase (CSP) using sub- and supercritical fluid chromatography (SFC). Compounds previously resolved on native or derivatized cyclodextrin CSPs in liquid chromatography (LC) using reversed phase or polar organic mobile phase modes could be resolved in SFC using a simple carbon dioxide/methanol eluent. Resolution of cromakalim, which is not possible on the S-NEC-CD column in LC, was readily accomplished in SFC. The importance of modifier, temperature, and pressure was assessed in relation to retention, selectivity, and resolution. The nature of the modifier and the modifier concentration were found to be crucial parameters. © 1996 Wiley-Liss, Inc. Contribution of the National Institute of Standards and Technology. Not subject to copyright.     

Comparison of polysaccharide-based and protein-based chiral liquid chromatography columns for enantioseparation of drugs

Two different columns—Lux Cellulose-1 and Chiralpak CBH—were evaluated for their chiral recognition abilities for eight drugs comprising three β-blockers, one antacid, and four cathinones in polar-organic elution mode and reversed-phase elution mode, respectively. The factors that affected the enantioseparation were tested and optimized to develop a suitable chiral separation method whose LC conditions are compatible with MS detection. In polar-organic elution mode with the Lux Cellulose-1 column, methanol and acetonitrile were tested as the main components of the mobile phase. In addition, the effects of adding isopropanol as organic modifier, acidic additives (formic acid), and basic additives (diethylamine) were evaluated. In reversed-phase elution mode with the Chiralpak CBH column, the effect of type and concentration of organic modifier (isopropanol, acetonitrile, and methanol), the mobile phase pH (6.4 and 5.0), and buffer concentration (1mM-20mM ammonium acetate) were evaluated. The best enantioseparation was achieved with the Chiralpak CBH column with a mobile phase composed of 5mM ammonium acetate aqueous (pH = 6.4)/methanol (95/5, v/v) at a flow rate of 0.1 mL/min and a temperature of 30°C. Under these conditions, six of eight chiral drugs were baseline separated.     

Optimization of throughput in semipreparative chiral liquid chromatography using stacked injection

An interesting mode of chromatography for preparation of pure enantiomers from pure samples is the method of stacked injection as a pseudocontinuous procedure. Maximum throughput and minimal production costs can be achieved by the use of total chiral column length in this mode of chromatography. To maximize sample loading, often touching bands of the two enantiomers is automatically achieved. Conventional equations show direct correlation between touching‐band loadability and the selectivity factor of two enantiomers. The important question for one who wants to obtain the highest throughput is “How to optimize different factors including selectivity, resolution, run time, and loading of the sample in order to save time without missing the touching‐band resolution?” To answer this question, tramadol and propranolol were separated on cellulose 3,5‐dimethyl phenyl carbamate, as two pure racemic mixtures with low and high solubilities in mobile phase, respectively. The mobile phase composition consisted of n‐hexane solvent with alcohol modifier and diethylamine as the additive. A response surface methodology based on central composite design was used to optimize separation factors against the main responses. According to the stacked injection properties, two processes were investigated for maximizing throughput: one with a poorly soluble and another with a highly soluble racemic mixture. For each case, different optimization possibilities were inspected. It was revealed that resolution is a crucial response for separations of this kind. Peak area and run time are two critical parameters in optimization of stacked injection for binary mixtures which have low solubility in the mobile phase.     

Optimization of chiral resolution using packed columns with carbon dioxide-based mobile phases

Optimization of chiral resolution, using carbon dioxide based mobile phases, must take into consideration the individual contributions of analyte retention, selectivity, and efficiency. Each of these factors may be independently affected by changes in pressure, temperature, or state of the mobile phase. The ability to control retention by different means reflects an advantage of carbon dioxide based mobile phases over conventional HPLC mobile phases. Utilization of this advantage requires that the effects of each of these factors on each contributor to resolution be known. The cumulative effect that each of these variables has on retention, selectivity and efficiency suggests that maximum resolution is obtained using low pressures and temperatures. Maximum resolution (at fixed k′) results from low temperatures and high pressures. The latter may be of more practical importance when speed of analyses and detection limits are considered. Chirality 9:672–677, 1997. © 1997 Wiley-Liss, Inc.     

Direct chiral separations of the enantiomers of phenylpyrazole pesticides and the metabolites by HPLC

The enantiomeric separation of the enantiomers of three phenylpyrazole pesticides (fipronil, flufiprole, ethiprole) and two fipronil metabolites (amide‐fipronil and acid‐fipronil) were investigated by high‐performance liquid chromatography (HPLC) with a CHIRALPAK^® IB chiral column. The mobile phase was n‐ hexane or petroleum ether with 2‐propanol or ethanol as modifier at a flow rate of 1.0 mL/min. The influences of mobile phase composition and column temperature between 15 and 35°C on the separations were studied. All the analytes except ethiprole obtained complete enantiomeric separation after chromatographic condition optimization. Fipronil, flufiprole, amide‐fipronil, and acid‐fipronil obtained complete separation with the best resolution factors of 2.40, 3.40, 1.67, and 16.82, respectively, but ethiprole showed no enantioselectivity under the optimized conditions. In general, n‐ hexane with 2‐propanol gave better separations in most cases. The results showed decreasing temperature and content of modifier in the mobile phase resulted in better separation and longer analysis time as well. The thermodynamic parameters calculated according to linear the Van't Hoff equation indicated the chiral separations in the study were enthalpy‐driven. Fipronil and its two chiral hydrolyzed metabolites obtained baseline separation simultaneously under optimized conditions.     

Effect of acidic mobile phase additives on chiral selectivity for phenylalanine analogs using subcritical fluid chromatography

A variety of acidic mobile phase additives were investigated as to their effects on retention, selectivity, efficiency, and overall chiral resolution for a number of chiral N‐substituted phenylalanine analogs under subcritical conditions. These mobile phase additives showed significant effects for all of the chromatographic parameters evaluated in this study. All of the phenylalanine analogs showed decreasing retention as the pK_a of the additive decreased. Plots of selectivity, efficiency, and chiral resolution showed pronounced improvement using acidic additives with pK_a values near −1. These results demonstrated that the choice of acidic mobile phase additives had a significant effect on the resulting chromatography for these chiral analytes under subcritical conditions. Chirality 11:91–97, 1999. © 1999 Wiley‐Liss, Inc.     

Optimum operational conditions for chiral separation of tryptophan enatiomers using ligand exchange liquid chromatography

A simple and precise method for chiral separation of tryptophan enantiomers using high performance liquid chromatography with aligand exchange mobile phase was developed. Chiral separation was performed on a conventional C₁₈ column, using a mobile phase that consisted of a water-methanol solution (88∶12, v/v) containing 10 mmol/Ll-leucine and 5 mmol/L copper sulfate as a chiral ligand additive at a flow rate of 1.0 mL/min. This method allowed baseline separation of two enantiomers with a resolution of 1.84 in less than 30 min. The effect of various conditions, including concentration, type of ligand, organic modifier, pH, flow rate, and temperature, on enantioseparation were evaluated and chiral recognition mechanisms were investigated. Thermodynamic data (ΔΔH and ΔΔS) obtained by van't Hoff plots revealed that enantioseparation is an enthalpy-controlled process.     

Direct HPLC separation of enantiomers of pantoprazole and other benzimidazole sulfoxides using cellulose-based chiral stationary phases in reversed-phase mode

A direct, isocratic, and simple reversed-phase HPLC method was described for the separation of enantiomers of the proton pump inhibitor, rac-pantoprazole (PAN) using cellulose-based chiral stationary phases (Chiralcel OD-R and Chiralcel OJ-R). Some structurally related chiral benzimidazole sulfoxides, rac-omeprazole (OME) and raclansoprazole (LAN), were also studied. Chiralcel OJ-R was successful in the resolution of enantiomers of rac-PAN and rac-OME, while Chiralcel OD-R was most suitable for resolving the enantiomers of rac-LAN. Highest enantioselectivity to rac-PAN and rac-OME was achieved on Chiralcel OJ-R by using acetonitrile as an organic modifier, whereas methanol afforded better resolution of rac-LAN on Chiralcel OD-R than acetonitrile. Increases in buffer concentration and column temperature decreased retention and did not improve the resolution of the enantiomers on both columns. Using a mixture of 50 mM sodium perchlorate solution and acetonitrile as a mobile phase at a flow rate of 0.5 ml/min, maximum separation factors of 1.26 and 1.13 were obtained for the enantiomers of rac-PAN and rac-OME using a Chiralcel OJ-R column, while maximum separation factor of 1.16 was obtained for the enantiomers of rac-LAN using a Chiralcel OD-R column. © 1995 Wiley-Liss, Inc.     

Chiral-recognition chromatography of β-blockers on continuous polymer beds with immobilized cellulase as enantioselective protein

Columns prepared by coupling cellulase as a chiral selector to silica beads are very efficient for the separation of enantiomers. In this paper we show that continuous polymer beds compete favorably with silica beads as chromatographic supports for such separations. The chiral stationary phase is prepared either by entrapment in and simultaneous covalent linkage of ally1 cellulase to the continuous beds during their preparation or by covalent immobilization of cellulase on an epoxy-activated continuous bed. Enantiomers of β-blockers were separated rapidly and with high resolution. The enantiomers of practolol were thus baseline resolved within 45 sec. The recognition center–or at least part of it—coincides with the active center of the enzyme, since the enantiomers could not be separated in the presence of the competitive enzyme inhibitors cellobiose and D-glucose and the separation was also impaired upon addition of the substrate carboxymethyl cellulose to the eluent. Similar observations have been reported for silica columns derivatized with cellulase. The capacity factor and the separation selectivity could be tuned by the pH and the concentration of the mobile phase, a phosphate buffer. No modifier was required, as is sometimes the case with silica-based supports. The continuous beds give faster enantiomer separations than do columns of silica and are more pH-stable and cost effective to prepare. © 1993 Wiley-Liss, Inc.     

Improvement of the enantiorecognition ability of tyrosine-derived chiral stationary phases: Direct resolution of 1,2-amino-alcohols (β-blockers)

A novel chiral stationary phase (CSP) derived from tyrosine is evaluated with regard to the first generation commercially available (S)-ChyRoSine-A CSP, under normalphase or reversed-phase liquid chromatographic (NPLC or RPLC) and subcritical fluid chromatographic (SubFC) conditions. The complete scope of application of these CSPs is reviewed. The novel CSP, which bears a bulkier functional group, displays a higher enantiorecognition ability than previously described (S)-ChyRoSine-A toward about 15 families of racemates, whatever the mobile phase conditions. The direct enantiomeric separation of 1,2-amino-alcohols (β-blockers) is carried out on both CSPs. Facile separations are achieved within short analysis times using SubFC mode, whereas very poor separations are obtained using NPLC mode. These results disagree with previous theories (interchangeability between NPLC and SubFC modes).     

Normal phase chiral HPLC of methylphenidate: comparison of different polysaccharide-based chiral stationary phases.

A comparison of the enantiomeric resolution of (+/-)-threo-methylphenidate (MPH) (Ritalin) was achieved on different polysaccharide based chiral stationary phases. The mobile phase used was hexane-ethanol-methanol-trifluoroacetic acid (480:9.75:9.75:0.5, v/v/v/v). Benzoic acid and phenol were used as the mobile phase additives for the enantiomeric resolution of MPH on Chiralcel OB column only. The alpha values for the resolved enantiomers were 1.34, 1.29, 1.30, and 1.24 on Chiralpak AD, Chiralcel OD, Chiralcel OB (containing 0.2 mM benzoic acid in mobile phase), and Chiralcel OB (containing 0.2 mM phenol in mobile phase) columns, respectively. The R(s) values were 1.82, 1.53, 1.19, and 1.10 on Chiralpak AD, Chiralcel OD, Chiralcel OB (containing 0.2 mM benzoic acid in mobile phase), and Chiralcel OB (containing 0.2 mM phenol in mobile phase), respectively. The role of benzoic acid and phenol as mobile phase additives is discussed.     

Enantiomeric Separations of Pyriproxyfen and its Six Chiral Metabolites by High‐Performance Liquid Chromatography

Pyriproxyfen is a chiral insecticide, and over 10 metabolites have been identified in the environment. In this work the separations of the enantiomers of pyriproxyfen and its six chiral metabolites were studied by high‐performance liquid chromatography (HPLC). Both normal phase and reverse phase were applied using the chiral columns Chiralpak IA, Chiralpak IB, Chiralpak IC, Chiralcel OD, Chiralcel OD‐RH, Chiralpak AY‐H, Chiralpak AD‐H, Chiracel OJ‐H, (R,R)‐Whelk‐O 1, and Lux Cellulose‐3. The effects of the chromatographic parameters such as mobile phase composition and temperature on the separations were investigated and the enantiomers were identified with an optical rotation detector. The enantiomers of these targets could obtain complete separations (resolution factor Rs > 1.5) on Chiralpak IA, Chiralpak IB, Chiralcel OD, Chiralpak AY‐H, or Chiracel OJ‐H under normal conditions. Chiralcel OJ‐H showed the best chiral separation results with n‐hexane as mobile phase and isopropanol (IPA) as modifier. The simultaneous enantiomeric separation of pyriproxyfen and four chiral metabolites was achieved on Chiralcel OJ‐H under optimized condition: n‐hexane/isopropanol = 80/20, 15°C, flow rate of 0.8 ml/min, and UV detection at 230 nm. The enantiomers of pyriproxyfen and the metabolites A , C , and D obtained complete separations on Chiralpak IA, Chiralpak IC, and Lux Cellulose‐3 under reverse phase using acetonitrile/water as the mobile phase. The retention factors (k) and selectivity factors (α) decreased with increasing temperature, and the separations were better under low temperature in most cases. The work is of significance for the investigation of the environmental behaviors of pyriproxyfen on an enantiomeric level. Chirality 28:245–252, 2016. © 2016 Wiley Periodicals, Inc.     

Chromatographic comparison of atenolol separation in reaction media on cellulose tris-(3,5-dimethylphenylcarbamate) chiral stationary phase using ultra fast liquid chromatography

Because chiral liquid chromatography (LC) could become a powerful tool to estimate racemic atenolol quantity, excellent enantiomeric separation should be produced during data acquisition for satisfactory observation of atenolol concentrations throughout the racemic resolution processes. Selection of chiral LC column and analytical protocol that fulfill demands of the ultra fast LC analysis is essential. This article describes the characteristics of atenolol chromatographic separation that resulted from different resolution media and analytical protocols with the use of a Chiralcel® OD column. The chromatograms showed quite different characteristics of the separation process. The single enantiomer and racemic atenolol could be recognized by the Chiralcel® OD column in less than 20 min. Symmetrical peaks were obtained; however, several protocols produced peaks with wide bases and slanted baselines. Observations showed that efficient enantioresolution of racemic atenolol was obtained at slow mobile phase flow rate, decreased concentration of amine‐type modifier but increased alcohol content in mobile phase and highest ultraviolet detection wavelength were required. The optimal ultra fast LC protocol enables to reduce and eliminate the peaks of either the atenolol solvent or the buffers and provided the highest peak intensities of both atenolol enantiomers. Chirality 24:356–367, 2012. © 2012 Wiley Periodicals, Inc.