Degradation of xenobiotics in a partitioning bioreactor in which the partitioning phase is a polymer

Two-phase partitioning bioreactors (TPPBs) are characterized by a cell-containing aqueous phase and a second immiscible phase that contains toxic and/or hydrophobic substrates that partition to the cells at subinhibitory levels in response to the metabolic demand of the organisms. To date, the delivery phase in TPPBs has been a hydrophobic solvent that traditionally needed to possess a variety of important properties including biocompatibility, nonbioavailability, low volatility, and low cost, among others. In the present work we have shown that the organic solvent phase can be replaced by inexpensive polymer beads that function in a similar fashion as organic solvents, delivering a toxic substrate to cells based on equilibrium considerations. Specifically, 3.4 mm diameter beads of poly(ethylene-co-vinyl acetate) (EVA) were used to reduce the aqueous concentration of phenol in a bioreactor from toxic levels ( approximately 2,000 mg/L) to subinhibitory levels ( approximately 750 mg/L), after which Pseudomonas putida ATCC 11172 was added to the system and allowed to consume the total phenol loading. Thus, the beads absorbed the toxic substrate and released it to the cells on demand. The EVA beads, which could be reused, were able to absorb 14 mg phenol/g EVA. This work has opened the possibility of using widely mixed cultures in TPPB systems without concern for degradation of the delivery material and without concern of contamination.     

Polymer selection for biphenyl degradation in a solid-liquid two-phase partitioning bioreactor

The commercially available thermoplastic polymer Hytrel was selected as the delivery phase for the hydrophobic model compound biphenyl in a solid-liquid two-phase partitioning bioreactor (TPPB), and 2.9 g biphenyl could successfully be degraded in 1-L TPPBs by a pure culture of the biphenyl-degrading bacterium Burkholderia xenovorans LB400 in 50 h and by a mixed microbial consortium isolated from contaminated soil in 45 h. TPPBs consist of an aqueous cell-containing phase and an immiscible second phase that partitions toxic and/or poorly soluble substrates (in this case biphenyl) on the basis of maintaining a thermodynamic equilibrium. This paper illustrates a rational strategy for selecting a suitable solid polymeric substance for the delivery of the poorly water-soluble model compound biphenyl. The partitioning of biphenyl between the selected polymers and water was analogous to partitioning of solutes between two immiscible liquid phases. The partitioning coefficients varied between 180 for Nylon 6.6 and 11,000 for Desmopan, where the later numerical value is comparable to biphenyl partitioning coefficients between water and organic solvents. Employing a solid delivery phase enabled the utilization of a surfactant-producing microbial mixed culture, which could not be cultivated in liquid-liquid TPPBs and thereby extended the range of biocatalysts that can be employed in TPPBs.     

A novel solid-liquid two-phase partitioning bioreactor for the enhanced bioproduction of 3-methylcatechol

The bioproduction of 3-methylcatechol from toluene via Pseudomonas putida MC2 was performed in a solid-liquid two-phase partitioning bioreactor with the intent of increasing yield and productivity over a single-phase system. The solid phase consisted of HYTREL, a thermoplastic polymer that was shown to possess superior affinity for the inhibitory 3-methylcatechol compared to other candidate polymers as well as a number of immiscible organic solvents. Operation of a solid-liquid biotransformation utilizing a 10% (w/w) solid (polymer beads) to liquid phase ratio resulted in the bioproduction of 3-methylcatechol at a rate of 350 mg/L-h, which compares favorably to the single phase productivity of 128 mg/L-h. . HYTREL polymer beads were also reconstituted into polymer sheets, which were placed around the interior circumference of the bioreactor and successfully removed 3-methylcatechol from solution resulting in a rate of 3-methylcatechol production of 343 mg/L-h. Finally, a continuous biotransformation was performed in which culture medium was circulated upwards through an external extraction column containing HYTREL beads. The design maintained sub lethal concentrations of 3-methylcatechol within the bioreactor by absorbing produced 3-methylcatechol into the polymer beads. As 3-methylcatechol concentrations in the aqueous phase approached 500 mg/L the extraction column was replaced (twice) with a fresh column and the process was continued representing a simple and effective approach for the continuous bioproduction of 3-methylcatechol. Recovery of 3-methylcatechol from HYTREL was also achieved by bead desorption into methanol.     

Polymer development for enhanced delivery of phenol in a solid-liquid two-phase partitioning bioreactor

Two-Phase Partitioning Bioreactors (TPPBs) have traditionally been used to partition toxic concentrations of xenobiotics from a cell-containing aqueous phase by means of an immiscible organic solvent and to deliver these substrates back to the cells on the basis of metabolic demand and the maintenance of thermodynamic equilibrium between the phases. A limitation of TPPBs, which use organic liquid solvents, is the possibility that the solvent can be bioavailable, and this has therefore limited organic liquid TPPBs to the use of pure strains of microbes. Solid polymer beads have recently been introduced as a replacement for liquid organic solvents, offering similar absorption properties but with the capability to be used with mixed microbial populations. The present work was aimed at identifying a polymer with a greater capacity for and more rapid uptake and release of phenol for use as the second phase in a mixed culture TPPB. Polarity and hydrogen bonding capabilities between polymer and phenol were considered in the screening and selection process of candidate polymers. Hytrel (a copolymer of poly(butylene terephthalate) and butylene ether glycol terephthalate) polymer beads, offered improved capacity (19 mg phenol/g polymer at a fixed initial phenol concentration of 2000 mg/L) and a greater diffusivity (1.54 x 10(-7) cm2/s) when compared to the capacity and diffusivity of previously used EVA (ethylene vinyl acetate) beads (12.4 mg phenol/g polymer and 3.73 x 10(-9) cm2/s, respectively). Hytrel polymer beads were then used in a TPPB for the investigation of various substrate feeding strategies (fed-batch, bead replacement, and concentrated spikes of phenol), with rapid and complete phenol degradation shown in all cases.     

Two-phase partitioning bioreactors for treatment of volatile organic compounds

Two-phase partitioning bioreactors (TPPBs) allow the biological removal of volatile organic compounds (VOCs) from contaminated gas streams at unprecedented rates and concentrations. TPPBs are constructed by adding a non-aqueous phase (e.g. hexadecane, silicone oil) to an aqueous phase that contains the microorganisms responsible for degrading the VOCs. Presence of a water-immiscible phase improves the transfer of hydrophobic substrates (e.g. hexane, oxygen) or reduces the toxicity of inhibitory substances (e.g. benzene, toluene) to the microorganisms present in the aqueous phase. The non-aqueous phase is selected based on cost, safety, good partitioning properties towards the target pollutants, biocompatibility, and non-biodegradability. TPPBs have hitherto been designed as laboratory-scale well-mixed stirred-tank reactors or as biofilters that contain a non-aqueous phase. Scale-up and industrial use of TPPBs require elucidation and modeling of the mechanisms of substrate transfer and uptake; understanding of the mechanisms of microbial selection; identification or synthesis of new inexpensive and robust non-aqueous phases; and generation of suitable guidelines for process design and control.     

A two‐phase partitioning airlift bioreactor for the treatment of BTEX contaminated gases

This investigation characterizes a novel 11 L airlift two‐phase partitioning bioreactor (TPPB) for the treatment of gases contaminated with a mixture of benzene, toluene, ethylbenzene, and o‐xylene (BTEX). The application of the TPPB technology in an airlift bioreactor configuration provides a novel technology that reduces energy intensity relative to traditional stirred tank TPPB configurations. The addition of a solid second phase of silicone rubber beads (10%, v/v) or of a liquid second phase of silicone oil (10%, v/v) resulted in enhanced performance of the airlift bioreactor relative to the single phase case, with 20% more BTEX being removed from the gas phase during an imposed transient loading. During a 4 h loading step change of three times the nominal loading (60 g m^?3 h^?1), overall removal efficiencies for the airlift TPPBs containing a liquid or solid phase remained above 75%, whereas the single phase airlift had an overall removal efficiency of 47.1%. The airlift TPPB containing a silicone rubber second phase was further characterized by testing performance during steady‐state operation over a range of loadings and inlet gas flow rates in the form of a 3² factorial experimental design. Optimal operating conditions that avoid oxygen limitations and that still have a slow enough gas flow rate for sufficient BTEX transfer from the gas phase to the working volume are identified. The novel solid–liquid airlift TPPB reduces energy inputs relative to stirred tank designs while being able to eliminate large amounts of BTEX during both steady‐state and fluctuating loading conditions. Biotechnol. Bioeng. 2009;103: 1077–1086. © 2009 Wiley Periodicals, Inc.     

Enhancement of PCB degradation by Burkholderia xenovorans LB400 in biphasic systems by manipulating culture conditions

Two-phase partitioning bioreactors (TPPBs) can be used to biodegrade environmental contaminants after their extraction from soil. TPPBs are typically stirred tank bioreactors containing an aqueous phase hosting the degrading microorganism and an immiscible, non-toxic and non-bioavailable organic phase functioning as a reservoir for hydrophobic compounds. Biodegradation of these compounds in the aqueous phase results in thermodynamic disequilibrium and partitioning of additional compounds from the organic phase into the aqueous phase. This self-regulated process can allow the delivery of large amounts of hydrophobic substances to degrading microorganisms. This paper explores the reactor conditions under which the polychlorinated biphenyl (PCB) degrader Burkholderia xenovorans LB400 can degrade significant amounts of the PCB mixture Aroclor(R) 1242. Aroclor(R) degradation was found to stall after approximately 40 h if no carbon source other than PCBs was available in the reactor. Sodium pyruvate was found to be a suitable carbon source to maintain microbial activity against PCBs and to function as a substrate for additional cell growth. Both biphenyl (while required during the inoculum preparation) and glucose had a negative effect during the Aroclor(R) degradation phase. Initial Aroclor(R) 1242 degradation rates in the presence of pyruvate were high (6.2 mg L(-1) h(-1)) and 85% of an equivalent concentration of 100 mg Aroclor(R) 1242 per L aqueous phase could be degraded in 48 h, which suggest that solvent extraction of PCBs from soil followed by their biodegradation in TPPBs might be a feasible remediation option.     

Enhanced biodegradation of phenol by a microbial consortium in a solid–liquid two phase partitioning bioreactor

Two phase partitioning bioreactors (TPPBs) operate by partitioning toxic substrates to or from an aqueous, cell-containing phase by means of second immiscible phase. Uptake of toxic substrates by the second phase effectively reduces their concentration within the aqueous phase to sub-inhibitory levels, and transfer of molecules between the phases to maintain equilibrium results in the continual feeding of substrate based on the metabolic demand of the microorganisms. Conventionally, a single pure species of microorganism, and a pure organic solvent, have been used in TPPBs. The present work has demonstrated the benefits of using a mixed microbial population for the degradation of phenol in a TPPB that uses solid polymer beads (comprised of ethylene vinyl acetate, or EVA) as the second phase. Polymer modification via an increase in vinyl acetate concentration was also shown to increase phenol uptake. Microbial consortia were isolated from three biological sources and, based on an evaluation of their kinetic performance, a superior consortium was chosen that offered improved degradation when compared to a pure strain of Pseudomonas putida ATCC 11172. The new microbial consortium used within a TPPB was capable of degrading high concentrations of phenol (2000mgl^–1), with decreased lag time (10h) and increased specific rate of phenol degradation (0.71g phenolg^–1cellh). Investigation of the four-member consortium showed that it consisted of two Pseudomonas sp., and two Acinetobacter sp., and tests conducted upon the individual isolates, as well as paired organisms, confirmed the synergistic benefit of their existence within the consortium. The enhanced effects of the use of a microbial consortium now offer improved degradation of phenol, and open the possibility of the degradation of multiple toxic substrates via a polymer-mediated TPPB system.     

Biodegradation of polycyclic aromatic hydrocarbons in a two-phase partitioning bioreactor in the presence of a bioavailable solvent

Mycobacterium PYR-1 was used in a two-phase partitioning bioreactor (TPPB) to degrade low and high molecular weight polycyclic aromatic hydrocarbons. TPPBs are characterized by a cell-containing aqueous phase, and an immiscible and biocompatible organic phase that partitions toxic substrates to the cells based on their metabolic demand and the thermodynamic equilibrium of the system. A bioavailable solvent, that is, a solvent usable as a carbon source, was used as the organic layer. Although bioavailable solvents are traditionally deemed unsuitable for use in TPPBs, bis(ethylhexyl) sebacate had superior chemical properties to other solvents examined and was cost-effective. In this system, 1 g of phenanthrene and 1 g of pyrene were completely degraded within 4 days, at rates of 168 mg l(-1) day(-1) and 138 mg l(-1 )day(-1), respectively, based on a 3-l aqueous volume. This is the highest pyrene degradation rate reported in the literature to date. Significant degradation of naphthalene and anthracene was also obtained. This work demonstrates that bioavailable solvents can be successfully used in TPPB systems, and may change the protocols commonly used to select solvents for TPPBs in the future.     

Improved reactor performance and operability in the biotransformation of carveol to carvone using a solid-liquid two-phase partitioning bioreactor

In an effort to improve reactor performance and process operability, the microbial biotransformation of (-)-trans-carveol to (R)-(-)-carvone by hydrophobic Rhodococcus erythropolis DCL14 was carried out in a two phase partitioning bioreactor (TPPB) with solid polymer beads acting as the partitioning phase. Previous work had demonstrated that the substrate and product become inhibitory to the organism at elevated aqueous concentrations and the use of an immiscible second phase in the bioreactor was intended to provide a reservoir for substrates to be delivered to the aqueous phase based on the metabolic rate of the cells, while also acting as a sink to uptake the product as it is produced. The biotransformation was previously undertaken in a two liquid phase TPPB with 1-dodecene and with silicone oil as the immiscible second phase and, although improvement in the reactor performance was obtained relative to a single phase system, the hydrophobic nature of the organism caused the formation of severe emulsions leading to significant operational challenges. In the present work, eight types of polymer beads were screened for their suitability for use in a solid-liquid TPPB for this biotransformation. The use of selected solid polymer beads as the second phase completely prevented emulsion formation and therefore improved overall operability of the reactor. Three modes of solid-liquid TPPB operation were considered: the use of a single polymer bead type (styrene/butadiene copolymer) in the reactor, the use of a mixture of polymer beads in the reactor (styrene/butadiene copolymer plus Hytrel(R) 8206), and the use of one type of polymer beads in the reactor (styrene/butadiene copolymer), and another bead type (Hytrel(R) 8206) in an external column through which fermentation medium was recirculated. This last configuration achieved the best reactor performance with 7 times more substrate being added throughout the biotransformation relative to a single aqueous phase benchmark reactor and 2.7 times more substrate being added relative to the best two liquid TPPB case. Carvone was quantitatively recovered from the polymer beads via single stage extraction into methanol, allowing for bead re-use.     

Solid-liquid two-phase partitioning bioreactors for the treatment of gas-phase volatile organic carbons (VOCs) by a microbial consortium

A two-phase partitioning bioreactor (TPPB), employing styrene-butadiene co-polymer beads as the sequestering/delivery phase, was used to treat high step change loadings of toluene in a contaminated air stream. The polymers, which are biocompatible and non-bioavailable, allowed the use of a microbial consortium and effectively absorbed and released the toluene vapours for biodegradation, while providing a buffering effect against high toluene transients. Toluene loadings were increased from a base steady state rate of 343-6,000 g/m(3) h for 1 h periods, with the polymer-aqueous system substantially outperforming a single phase system on the basis of improving the toluene removal efficiency and reducing the maximum toluene concentrations emitted during the transients.     

Expanded application of a two-phase partitioning bioreactor through strain development and new feeding strategies

This research demonstrated the microbial treatment of concentrated phenol wastes using a two-phase partitioning bioreactor (TPPB). TPPBs are characterized by a cell-containing aqueous phase and an immiscible and biocompatible organic phase that partitions toxic substrates to the cells on the basis of their metabolic demand and the thermodynamic equilibrium of the system. Process limitations imposed by the capability of wild-type Pseudomonas putida ATCC 11172 to utilize long chain alcohols were addressed by strain modification (transposon mutagenesis) to eliminate this undesirable biochemical characteristic, enabling use of a range of previously bioavailable organics as delivery solvents. Degradation of phenol in a system with the modified strain as catalyst and industrial grade Adol 85 NF (primarily oleyl alcohol) as the solvent was demonstrated, with the system ultimately degrading 36 g of phenol within 38 h. Volumetric phenol consumption rates by wild type P. putida ATCC 11172 and the genetically modified derivative revealed equivalent phenol degrading capabilities (0.49 g/L x h vs 0.47 g/L x h respectively, in paired fermentations), with the latter presenting a more efficient remediation option due to decreased solvent losses arising from the modified strain's forced inability to consume the delivery solvent as a substrate. Two feeding strategies and system configurations were evaluated to expand practical applications of TPPB technology. The ability to operate with a lower solvent ratio over extended periods revealed potential for long-term application of TPPB to the treatment of large masses of phenol while minimizing solvent costs. Repeated recovery of 99% of phenol from concentrated phenol solutions and subsequent treatment within a TPPB scheme demonstrated applicability of the approach to the remediation of highly contaminated "effluents" as well as large masses of bulk phenol. Operation of the TPPB system in a dispersed manner, rather than as two distinct phases, resulted in volumetric consumption rates similar to those previously achieved only in systems operated with enriched air.     

A systematic selection of the non-aqueous phase in a bacterial two liquid phase bioreactor treating α-pinene

A systematic evaluation of the selection criteria of non-aqueous phases in two liquid phase bioreactors (TLPBs), also named two-phase partitioning bioreactors (TPPBs), was carried out using the biodegradation of α-pinene by Pseudomonas fluorescens NCIMB 11671 as a model process. A preliminary solvent screening was thus carried out among the most common non-aqueous phases reported in literature for volatile organic contaminants biodegradation in TLPBs: silicon oil, paraffin oil, hexadecane, diethyl sebacate, dibutyl-phtalate, FC 40, 1,1,1,3,5,5,5-heptamethyltrisiloxane (HMS), and 2,2,4,4,6,8,8-heptamethylnonane (HMN). FC 40, silicone oil, HMS, and HMN were first selected based on its biocompatibility, resistance to microbial attack, and α-pinene mass transport characteristics. FC 40, HMS, HMN, and silicone oil at 10% (v/v) enhanced α-pinene mass transport from the gas to the liquid phase by a factor of 3.8, 14.8, 11.4, and 8.6, respectively, compared to a single-phase aqueous system. FC 40 and HMN were finally compared for their ability to enhance α-pinene biodegradation in a mechanically agitated bioreactor. The use of FC 40 or HMN (both at 10% v/v) sustained non-steady state removal efficiencies (RE) and elimination capacities (EC) approximately 7 and 12 times higher than those achieved in the system without an organic phase, respectively. In addition, preliminary results showed that P fluorescens could uptake and mineralize α-pinene directly from the non aqueous phase.     

Enhanced bioproduction of carvone in a two-liquid-phase partitioning bioreactor with a highly hydrophobic biocatalyst

The microbial biotransformation of (-)-trans-carveol to the flavor and fragrance compound (R)-(-)-carvone by Rhodococcus erythropolis DCL14 was carried out in a 3 L two phase partitioning bioreactor with an immiscible liquid second phase in an effort to improve upon the reactor performance achieved in a single aqueous phase system. The purpose of employing the liquid second phase is to minimize biotransformation rate inhibition due to the accumulation of the toxic substrate (cis-carveol) and product (carvone) in the aqueous phase. 1-Dodecene was chosen as the solvent for this application because it is biocompatible, non-biodegradable and has a superior affinity for the target product (carvone) relative to the other solvents tested. However, when 1-dodecene was used in the biotransformation, the extremely hydrophobic R. erythropolis DCL14 created an emulsion with the organic solvent with significant sequestering of the cells into the organic phase and negligible substrate conversion. To overcome these operational difficulties, silicone oil, which is considered a liquid polymer, was used with the aim of preventing emulsification and sequestration of cells in the non-aqueous phase. Although some emulsification of the water-silicone oil was again created by the cells, operability was improved and, in fed-batch mode, the system was able to convert approximately 2(1/2) times more carveol than a benchmark single aqueous phase system before substrate/product toxicity caused the biotransformation to stop. This study has demonstrated enhancement of a microbial biotransformation for the production of a high value nutraceutical compound via the use of a second partitioning phase, along with operational challenges arising from the use of a highly hydrophobic organism in such systems.     

Biodegradation of a phenolic mixture in a solid–liquid two-phase partitioning bioreactor

A solid–liquid two-phase partitioning bioreactor (TPPB) in which the non-aqueous phase consisted of polymer (HYTREL) beads was used to degrade a model mixture of phenols [phenol, o-cresol, and 4-chlorophenol (4CP)] by a microbial consortium. In one set of experiments, high concentrations (850 mg l⁻¹ of each of the three substrates) were reduced to sub-inhibitory levels within 45 min by the addition of the polymer beads, followed by inoculation and rapid (8 h) consumption of the total phenolics loading. In a second set of experiments, the beneficial effect of using polymer beads to launch a fermentation inhibited by high substrate concentrations was demonstrated by adding 1,300 and 2,000 mg l⁻¹ total substrates (equal concentrations of each phenolic) to a pre-inoculated bioreactor. At these levels, no cell growth and no degradation were observed; however, after adding polymer beads to the systems, the ensuing reduced substrate concentrations permitted complete destruction of the target molecules, demonstrating the essential role played by the polymer sequestering phase when applied to systems facing inhibitory substrate concentrations. In addition to establishing alternative modes of TPPB operation, the present work has demonstrated the differential partitioning of phenols in a mixture between the aqueous and polymeric phases. The polymeric phase was also observed to absorb a degradation intermediate (arising from the incomplete biodegradation of 4CP), which opens the possibility of using solid–liquid TPPBs during biosynthetic transformation to sequester metabolic byproducts.     

Substrate mass transport in two-phase partitioning bioreactors employing liquid and solid non-aqueous phases

The mass transfer of phenol and butyl acetate to/from water was studied in two-phase partitioning bioreactors using immiscible organic solvents and solid polymer beads as the partitioning phases in a 5-L stirred tank bioreactor. Virtually instantaneous mass transfer was observed with phenol in water/2-undecanone, and with butyl acetate in water/silicone oil systems. The mass transfer of butyl acetate to silicone oil was rapid irrespective of the viscosity of the partitioning phase. When Hytrel(?) polymer beads were employed as the partitioning phase, substrate transport to the polymer was found not to be externally mass transfer limited, but rather internally by substrate diffusion into the polymer. In contrast to gaseous, poorly soluble substrates studied in other works, mass transfer of soluble substrates such as phenol and butyl acetate to the polymer was unaffected by impeller speed but rather by polymer mass fraction.     

Phase change enzyme immunoassay

A novel enzyme-linked immunoassay employing a partitioning chromophore was developed. The assay system consisted of an aqueous phase and an immiscible organic solvent. Antigen-antibody interaction was indicated by transfer of a chromogenic indicator from the aqueous phase to an organic layer. The indicator employed was a water-soluble phosphate ester of phenylazophenol. Hydrolysis of the ester by acid or alkaline phosphatase produced a water-insoluble phenol that partitioned into toluene. The enzyme employed in this assay format can be covalently linked to antibody or a specific antibody for the phosphatase can be used. Phase change immunoassays were developed for the measurement of alkaline phosphatase, human IgG in whole blood, and the human tumor marker prostatic acid phosphatase. Solid supports of small polystyrene latex particles and Sephadex were employed.     

Enhanced Degradation of a Mixture of Polycyclic Aromatic Hydrocarbons by a Defined Microbial Consortium in a Two-Phase Partitioning Bioreactor

Biological treatment methods are effective at destroying polycyclic aromatic hydrocarbons (PAHs), and some of the highest rates of PAH degradation have been achieved using two-phase-partitioning bioreactors (TPPBs). TPPBs consist of a cell-containing aqueous phase and a biocompatible and immiscible organic phase that partitions toxic and/or recalcitrant substrates to the cells based on their metabolic demand and on maintaining the thermodynamic equilibrium of the system. In this study, the degradation of a 5-component mixture of high and low molecular weight PAHs by a defined microbial consortium of Sphingomonas aromaticivorans B0695 and Sphingomonas paucimobilis EPA505 in a TPPB was examined. The extremely low aqueous solubilities of the high molecular weight (HMW) PAHs significantly reduce their bioavailability to cells, not only in the environment, but in TPPBs as well. That is, in the two-phase system, the originally selected solvent, dodecane, was found to sequester the HMW PAHs from the cells in the aqueous phase due to the inherent high solubility of the hydrophobic compounds in this solvent. To circumvent this limitation, the initial PAH concentrations in dodecane were increased to sufficient levels in the aqueous phase to support degradation: LMW PAHs (naphthalene, phenanthrene) and fluoranthene were degraded completely in 8 h, while the HMW PAHs, pyrene and benzo[a]pyrene, were degraded by 64% and 11%, at rates of 42.9 mg l⁻¹ d⁻¹ and 7.5 mg l⁻¹ d⁻¹, respectively. Silicone oil has superior PAH partitioning abilities compared to dodecane for the HMW PAHs, and was used to improve the extent of degradation for the PAH mixture. Although silicone oil increased the bioavailability of the HMW PAHs and greater extents of biodegradation were observed, the rates of degradation were lower than that obtained in the TPPB employing dodecane.     

Benzene/toluene/p-xylene degradation. Part I. Solvent selection and toluene degradation in a two-phase partitioning bioreactor

A two-phase organic/aqueous reactor configuration was developed for use in the biodegradation of benzene, toluene and p-xylene, and tested with toluene. An immiscible organic phase was systematically selected on the basis of predicted and experimentally determined properties, such as high boiling points, low solubilities in the aqueous phase, good phase stability, biocompatibility, and good predicted partition coefficients for benzene, toluene and p-xylene. An industrial grade of oleyl alcohol was ultimately selected for use in the two-phase partitioning bioreactor. In order to examine the behavior of the system, a single-component fermentation of toluene was conducted with Pseudomonas sp. ATCC 55595. A 0.5-l sample of Adol 85 NF was loaded with 10.4 g toluene, which partitioned into the cell containing 1 l aqueous medium at a concentration of approximately 50 mg/l. In consuming the toluene to completion, the organisms were able to achieve a volumetric degradation rate of 0.115 g l⁻¹ h⁻¹. This system is self-regulating with respect to toluene delivery to the aqueous phase, and requires only feedback control of temperature and pH. Received: 16 November 1998 / Received revision: 28 March 1999 / Accepted: 9 April 1999     

Biodegradation of toluene at high initial concentration in an organic–aqueous phase bioprocess with nitrate respiration

An aerobic organic–aqueous system with forced aeration was shown to be inefficient in preventing significant volatile aromatic compounds loss in gassed systems since air sparging in n-hexadecane under abiotic conditions could reduce the toluene concentration from 2.1 g/L to about 0.5 g/L in 3 days with a gassing rate of 1VVM at 20 °C. However, the presence of such an organic phase was found to significantly reduce substrate loss in aerobic conditions in comparison to pure aqueous systems. It was thus decided to develop a new bioprocess based on an anaerobic microbial system operated in an organic–aqueous phase with nitrate respiration. The denitrifying bacterium used, Thauera aromatica K172, was produced by cultivation on sodium benzoate as carbon source under anaerobic conditions. This cultivated biomass (1.5 g/L) was shown to retain its ability to efficiently metabolize toluene in a biphasic medium without any significant loss of organic compound in the gas phase. Toluene biodegradation was thus performed in a biphasic system using a fed-batch technique involving sequential adding of both toluene and nitrate. The reaction rate with an initial concentration of toluene close to 14.5 g/L in hexadecane was found to be close to 0.5 g/L day and the molar stoichiometry of solute metabolization to nitrate reduction was close to 1:6. This work demonstrated that the denitrifying bacteria could efficiently degrade toluene in hexadecane–aqueous phase systems in which toxic compound release in the environment was prevented.