Impact of Harvest Equipment on Ash Variability of Baled Corn Stover Biomass for Bioenergy

Cost-effective conversion of agricultural residues for renewable energy hinges not only on the material’s quality but also the biorefinery’s ability to reliably measure quality specifications. The ash content of biomass is one such specification, influencing pretreatment and disposal costs for the conversion facility and the overall value of a delivered lot of biomass. The biomass harvest process represents a primary pathway for accumulation of soil-derived ash within baled material. In this work, the influence of five collection techniques on the total ash content and variability of ash content within baled corn stover in southwest Kansas is discussed. The equipment tested included a mower for cutting the corn stover stubble, a basket rake, wheel rake, or shred flail to gather the stover, and a mixed or uniform in-feed baler for final collection. The results showed mean ash content to range from 11.5 to 28.2 % depending on operational choice. Resulting impacts on feedstock costs for a biochemical conversion process range from $5.38 to $22.30 Mg^?1 based on the loss of convertible dry matter and ash disposal costs. Collection techniques that minimized soil contact (shred flail or nonmowed stubble) were shown to prevent excessive ash contamination, whereas more aggressive techniques (mowing and use of a wheel rake) caused greater soil disturbance and entrainment within the final baled material. Material sampling and testing were shown to become more difficult as within-bale ash variability increased, creating uncertainty around feedstock quality and the associated costs of ash mitigation.     

LCA case study. Part 2: environmental footprint and carbon tax of cradle-to-gate for composite and stainless steel I-beams

Purpose

Part 1 of this research investigated environmental footprint for the cradle-to-grave of a linear metre I-beam made from traditional and alternative materials which are stainless steel (316) and glass reinforced plastics (GRP). Results revealed that GRP generally produced less environmental footprint than stainless steel. The main contribution found in the cradle-to-gate caused by raw materials (90 %) and associated transportation (10 %). Certain impact categories of GRP were either equalled or higher than stainless steel I-beam including the climate change impact category. Therefore, part 2 of this research further investigates the ecological and economic hot spots of the cradle-to-gate of GRP I-beam and alternative supply chain scenarios. The potential carbon tax was also estimated under two different situations.

Methods

GRP and stainless steel (316) are used to assess the environmental footprint and the economic impact of 6,098 m I-beams as a production volume in practice. The World ReCiPe midpoint and endpoint methods generated the life cycle inventory, characteristic and single score results for the environmental footprint. The economic impact estimated based on a simple cost calculation associated with the cradle-to-gate including material, production and transportation costs. The ecological and economic hot spots were identified and formed 12 supply chain scenarios.

Results and discussion

Both identified hot spots came from raw materials that used in large quantities, consumed higher electricity and delivered by road and water transportation over long travel distances. The climate change impact category and the potential carbon tax values are improved under the scenarios that use a supplier from countries that generate electricity from less coal-based energy source and involve less transportation in delivering the raw materials.

Conclusions

Win–win and trade-off scenarios were revealed when comparing both impacts. The former scenario reduces material costs, the travel distances and using lower freight rate transportation that consumes less fuel such as shipping. The latter scenarios are often occurred by either attempting to reduce the environmental footprint from using less transportation but the raw material costs are suffered. Manufacturers may select the scenario based on their production constrains. Cradle-to-grave was discussed and shown the benefits in including steel recycling into the assessment which can equate the potential carbon tax of the stainless steel with some GRP I-beam scenarios. Future work can be enhanced by considering other factors in the practice of manufacturing system such as insurance cost and lead time.     

Importance of good manufacturing practices in microbiological monitoring in processing human tissues for transplant

Skin allografts represent an important therapeutic resource in the treatment of severe skin loss. The risk associated with application of processed tissues in humans is very low, however, human material always carries the risk of disease transmission. To minimise the risk of contamination of grafts, processing is carried out in clean rooms where air quality is monitored. Procedures and quality control tests are performed to standardise the production process and to guarantee the final product for human use. Since we only validate and distribute aseptic tissues, we conducted a study to determine what type of quality controls for skin processing are the most suitable for detecting processing errors and intercurrent contamination, and for faithfully mapping the process without unduly increasing production costs. Two different methods for quality control were statistically compared using the Fisher exact test. On the basis of the current study we selected our quality control procedure based on pre- and post-processing tissue controls, operator and environmental controls. Evaluation of the predictability of our control methods showed that tissue control was the most reliable method of revealing microbial contamination of grafts. We obtained 100 % sensitivity by doubling tissue controls, while maintaining high specificity (77 %).     

Enhanced Soil Washing for the Remediation of a Brownfield Polluted by Pyrite Ash

Soil from an abandoned/disused fertilizer plant polluted with pyrite ash containing heavy metal(loid)s (As, Cu, Pb, and Zn) was treated by means of physical and chemical washing. We first performed an exhaustive characterization of the soil-pollutant interaction, which allowed us to determine the chemical nature (complex oxyhydroxides), potential mobility and bioavailability of the pollutants (very low), as well as the grain size fractions of preferential accumulation (silt-clay fraction comprises more than 60% of the material and revealed contents well above 2.000 ppm of Cu, Zn and Pb). Soil/ash samples were subjected to a number of chemical washing trials, including leaching with 2 M HCl, 2 M NaOH and acidic process water (pH around 0). The fraction below 63 µm was mechanically separated and exposed to additional leaching tests e.g. chloridizing roasting with NaCl plus water leaching. Of all the tested procedures, the latter proved the most effective, particularly with regard to Cu and Zn recovery (recoveries up to 40% and 34%, respectively). The information gathered offers an insight into the modes and rates at which metals can be leached from pyrite ashes after chloridizing roasting as a prelude to more extensive soil washing feasibility studies focused on potential metal recovery.     

Improving Woody Biomass Feedstock Logistics by Reducing Ash and Moisture Content

We examined two practical methods for reducing moisture content and/or ash content in biomass from southern pine harvests. Logging residues are a potential bioenergy feedstock, but contaminants can increase ash content during collection. We found that trommel screens can reduce ash levels in grindings from southern pine roundwood and clean chipped logging residues from 4.0 to 1.4 % and 11.9 to 6 %, respectively. Green whole-tree chips are a widely used form of forest biomass, but are 50 % moisture. Felling and transpirationally drying in-field before chipping reduced moisture from 53 to 43 % and 39 % in 4 and 8 weeks, respectively, without changing ash content (<0.7 %). Finally, we used data from the screening and drying studies in a simulation study to estimate delivered costs for whole-tree chipping and screened and unscreened grinders processing logging and clean chip residue. Whole-tree chipping provided the lowest cost option at ash content levels less than 1 %, and unscreened grinding of clean chip residue produced the least expensive option at 5 % ash.     

Counter-Current Metal Leaching and Precipitation for Soil Remediation

Chemical acid leaching is an effective technique for extracting toxic metals from the finest fractions of polluted soils. Nevertheless, the use of large quantities of reagents and process water results in prohibitive operating costs. The purpose of this study was to evaluate the technical and economic advantages of recirculating water in a counter-current leaching process (CCLP). Five 1-h sulfuric acid extraction steps (at pH = 1.5) followed by three 5-min water-washing steps were applied to the fine particle fraction (<0.125 mm) of an industrial soil polluted by Cd (13.2 mg·kg^?1), Cu (3 100 mg·kg^?1), Mn (685 mg kg^?1), Pb (550 mg·kg^?1), and Zn (2 840 mg·kg^?1). The leaching experiments were carried out at ambient temperature using a 10% soil suspension and in 1-L working volume stirred tank reactors. This paper presents results of conventional and counter-current leaching process (CCLP) tests and shows that the CCLP yields removal results for Cu (85%), Zn (86%), Mn (75%), and Cd (90%) that are similar to those obtained using the conventional leaching process. Moreover, the CCLP uses half of the quantity of acid and one-eighth of the amount of water that the conventional process uses. Metal precipitation with NaOH and Ca(OH)₂ was applied to treat the acidic leachates, and good metal removal yields were achieved with both reagents. However, the large consumption of chemicals implies high operating costs. In addition, the precipitation causes considerable sludge production, particularly when using Ca(OH)₂. Overall, the CCLP coupled to metal precipitation using NaOH and water recycling appears to be the most attractive option for the removal of toxic metals from this industrial soil.     

Carbon and nutrient losses during manure storage under traditional and improved practices in smallholder crop-livestock systems—evidence from Kenya

In the absence of mineral fertiliser, animal manure may be the only nutrient resource available to smallholder farmers in Africa, and manure is often the main input of C to the soil when crop residues are removed from the fields. Assessments of C and nutrient balances and cycling within agroecosystems or of greenhouse gas emissions often assume average C and nutrient mass fractions in manure, disregarding the impact that manure storage may have on C and nutrient losses from the system. To quantify such losses, in order to refine our models of C and nutrient cycling in smallholder (crop-livestock) farming systems, an experiment was conducted reproducing farmers’ practices: heaps vs. pits of a mix of cattle manure and maize stover (2:3 v/v) stored in the open air during 6 months. Heaps stored under a simple roof were also evaluated as an affordable improvement of the storage conditions. The results were used to derive empirical models and graphs for the estimation of C and nutrient losses. Heaps and pits were turned every month, weighed, and sampled to determine organic matter, total and mineral N, P and K mass fractions. Soils beneath heaps/pits were sampled to measure mineral N to a depth of 1 m, and leaching tube tests in the laboratory were used to estimate P leaching from manure. After 6 months, ca. 70% remained of the initial dry mass of manure stored in pits, but only half of or less of the manure stored in heaps. The stored manure lost 45% of its C in the open air and 69% under roof. The efficiencies of nutrient retention during storage varied between 24–38% for total N, 34–38% for P and 18–34% for K, with the heaps under a roof having greater efficiencies of retention of N and K. Laboratory tests indicated that up to 25% of the P contained in fresh manure could be lost by leaching. Results suggest that reducing the period of storage by, for example, more frequent application and incorporation of manure into the soil may have a larger impact on retaining C and nutrient within the farm system than improving storage conditions.     

A life cycle comparison of disposal and beneficial use of coal combustion products in Florida

Background, aim, and scope  Beneficial use of coal combustion products (CCPs) in industrial or construction operations has the potential to minimize environmental and human health impacts that would otherwise be associated with disposal of CCPs in the life cycle of coal used for electricity generation. To assess opportunities for reducing impacts associated with four CCP materials considered in this study, fly ash, bottom ash, boiler slag, and flue gas desulfurization (FGD) material, this paper reports results of expanding a life cycle inventory of raw material and emissions (part 1 of this series of papers) by performing life cycle impact assessment on five scenarios of CCP management. Materials and methods  SimaPro 5.1 software (PRé Consultants) was used to calculate comparative environmental impacts of all scenarios using CML2001 and Environmental Design of Industrial Products 1997 midpoint impact assessment methods and Heirarchist and Individualist levels of the Eco-indicator 99 end point method. Trends were compared for global and local environmental and human health impact categories of global warming, acidification, smog formation, human toxicity, and ecotoxicity. Results  In each impact category, beneficial use of fly ash, bottom ash, and FGD material resulted in a reduced impact compared to disposal of these materials. The extent to which beneficial use reduced impacts depended on several factors, including the impact category in consideration, the magnitude of potentially avoided impacts associated with producing raw materials that CCPs replace, and the potential impact of CCP disposal methods. Global warming impacts were reduced by the substitution of fly ash for Portland cement in concrete production, as production of Portland cement generates large quantities of CO₂. However, for categories of global warming, smog formation, and acidification, impact reductions from CCP beneficial use are small, less than 6%, as these impacts were attributable, in greater part, to upstream processes of coal mining, transportation, and combustion. Human toxicity and ecotoxicity categories showed larger but more varied reductions, from 0% to 50%, caused by diverting CCPs from landfills and surface impoundments. Discussion  When comparing beneficial use scenarios, the four impact assessment methods used showed similar trends in categories of global warming, acidification, and smog formation. However, results diverged for human toxicity and ecotoxicity categories due to the lack of consensus among methods in classification and characterization of impacts from heavy metal release. Similarly, when assessing sensitivity of these results to changes in assumptions or system boundaries, human toxicity and ecotoxicity categories were most susceptible to change, while other impact categories had more robust results. Conclusions  Impact assessment results showed that beneficial use of CCPs presented opportunities for reduced environmental impacts in the life cycle of coal combusted for electricity generation, as compared to the baseline scenario of 100% CCP disposal, although the impact reductions varied depending on the CCPs used, the ultimate beneficial use, and the impact category in consideration. Recommendations and perspectives  As regulators and electric utilities increasingly consider viability and economics of the use of CCPs in various applications, this study provides a first-basis study of selected beneficial use alternatives. With these initial results, future studies should be directed towards beneficial uses that promise significant economic and environmental savings, such as use of fly ash in concrete, to quantify the currently unknown risk of these applications.     

Combustion influences on natural abundance nitrogen isotope ratio in soil and plants following a wildfire in a sub-alpine ecosystem

This before-and-after-impact study uses the natural abundance N isotope ratio (δ¹⁵N) to investigate the effects of a wildfire on sub-alpine ecosystem properties and processes. We measured the ¹⁵N signatures of soil, charred organic material, ash and foliage in three sub-alpine plant communities (grassland, heathland and woodland) in south-eastern Australia. Surface bulk soil was temporarily enriched in ¹⁵N immediately after wildfire compared to charred organic material and ash in all plant communities. We associated the enrichment of bulk soil with fractionation of N during combustion and volatilization of N, a process that also explains the sequential enrichment of ¹⁵N of unburnt leaves > ash > charred organic material in relation to duration and intensity of heating. The rapid decline in ¹⁵N of bulk soil to pre-fire values indicates that depleted ash, containing considerable amounts of total N, was readily incorporated into the soil. Foliar δ¹⁵N also increased with values peaking 1 year post-fire. Foliar enrichment was foremost coupled with the release of enriched NH₄ ⁺ into the soil owing to isotopic discrimination during volatilization of soluble N and combustion of organic material. The mode of post-fire regeneration influenced foliar ¹⁵N enrichment in two species indicating use of different sources of N following fire. The use of natural abundance of ¹⁵N in soil, ash and foliage as a means of tracing transformation of N during wildfire has established the importance of combustion products as an important, albeit temporary source of inorganic N for plants regenerating after wildfire.     

Life cycle assessment of the supply chain of a Portuguese wine: from viticulture to distribution

Purpose

This paper performs a life cycle assessment study for a white wine produced in the northern part of Portugal, i.e. the white vinho verde. The purpose is to identify the environmental impacts occurring along the wine life cycle as well as the stages that mostly contribute to the environmental impact, as well as the associated causes. The stages considered include: (1) viticulture, (2) wine production (vinification to storage), (3) wine distribution and (4) bottles production.

Methods

The consumption of materials and energy, as well as the emissions to air, soil and water from the wine campaign of 2008/2009 were reported to the functional unit (0.75 l of white vinho verde). A Portuguese company that produces about 25 % of the current total production of white vinho verde supplied specific life cycle data for the stages of viticulture, wine production and distribution. SimaPro and the Ecoinvent database were used to perform the environmental assessment using CML 2001 impact methodology. A sensitivity analysis for a set of significant parameters was performed.

Results

Results show that for viticulture the contribution of each impact category is larger than 50 %. The production of bottles is the second contributor varying from about 4 % (to eutrophication) to 26 % (to acidification). Wine production and distribution are the subsequent contributors. The contribution of wine production varies between 0.6 % (to land competition) and about 13 % (from marine aquatic and sediment ecotoxicity 100a). The contribution of distribution is up to 14 % (to photochemical oxidation). Sensitivity analysis shows that significant changes are calculated for parameters as the nitrate leaching to groundwater, the emission of nitrous oxide from managed soil, and from runoff and leaching. Changes in these parameters are significant for only a few impact categories as eutrophication and global warming.

Conclusions

Viticulture is the stage with the largest relative contribution to the overall environmental impact and the bottle production is the subsequent stage. In order to improve the environmental performance of the supply chain for wine, it is necessary to optimise the dosage of fertilisers and phytosanitary products used during viticulture. The sensitivity analysis demonstrates that the most influential parameters relate with the emission of nitrogen compounds associated with the use of fertilisers.     

LCA case study. Part 1: cradle-to-grave environmental footprint analysis of composites and stainless steel I-beams

Purpose

I-beams for outdoor structures are traditionally made from conventional materials such as stainless steel due to its high strength and corrosive resistant properties. Alternatively, the I-beam can also be made from composite materials such as glass-reinforced plastics (GRP), which provide similar properties under a lighter weight and a lower cost condition. Nonetheless, their environmental footprint performance depends largely on activities involved during their life cycle. Therefore, the findings are presented in two parts: Part 1 and 2. This paper is about Part 1, which presents the environmental footprint for the cradle-to-grave of one linear metre I-beam that is made from two materials namely stainless steel (316) and GRP. Part 2, which will be submitted as a separate paper, has specifically analysed their environmental and economic impacts for the different cradle-to-gate scenarios and the potential carbon tax.

Materials and methods

Materials that were used to compare the environmental footprint of an I-beam are GRP and stainless steel (316). Their cradle-to-grave activities included raw material extraction, supplier transportation, manufacturing process, distribution, disposal transportation and process. Input data were based on data provided by a composites company in Australia, the Ecoinvent 2.2 and Australian data 2007 databases. The World ReCiPe midpoint and endpoint methods were used to assess the environmental footprint.

Results and discussion

The environmental footprint results for the cradle-to-grave of the I-beams are presented as a contribution percentage of the single score unit in the total and damage category levels which produced by the endpoint method. The characteristic and normalisation results were also generated for all impact categories by the midpoint method.

Conclusions

Overall, the cradle-to-grave results show that the composite I-beam produces 20 % less environmental footprint than that of the stainless steel I-beam. The human health damage category is affected the most due to the main contribution from the material stage. The cradle-to-gate results are contributed by 90 % from raw material extraction, 7 % from the manufacturing process and 3 % from the supplier transportation. In terms of the characteristic results, the composite I-beam produces less environmental impact in most of the impact categories except for the climate change, photochemical oxidant formation, terrestrial acidification, marine eutrophication, natural land transformation and fossil depletion. Therefore, the influential parameters of these impact categories are investigated further in Part 2 where the environmental footprint and economic impact are estimated for different cradle-to-gate scenarios of the I-beams.     

Environmental impacts of end-of-life vehicles’ management: recovery versus elimination

Purpose

In Portugal, the management of end-of-life vehicles (ELV) is set out in targets of the European Union policy for the year 2015, including 85 % recycling, 95 % recovery, and maximum of 5 % landfilling. These goals will be attained only through more efficient technologies for waste separation and recycling of shredder residues or higher rates of dismantling components. Focusing on this last alternative, a field experiment was carried out. There is potential for additional recycling/recovery of 10 %.

Methods

Three scenarios were proposed for the management of ELV wastes: (1) scenario 1 corresponds to the baseline and refers to the current management, i.e., the 10 % of ELV wastes are shredded whereby some ferrous and non-ferrous metals are recovered and the remaining fraction, called automotive shredder residues (ASR), is landfilled, (2) scenario 2 wherein the ASR fraction is incinerated with energy recovery, and (3) scenario 3 includes the additional dismantling of components for recycling and for energy recovery through solid recovered fuel, to be used as a fuel substitute in the cement industry. The environmental performance of these scenarios was quantified by using the life cycle assessment methodology. Five impact categories were assessed: abiotic resource depletion, climate change, photochemical oxidant creation, acidification, and eutrophication.

Results and discussion

Compared to the other scenarios, in scenario 1 no benefits for the impact categories of climate change and eutrophication were observed. Scenario 2 has environmental credits due to the recycling of ferrous and non-ferrous metals and benefits from energy recovery. However, this scenario has a significant impact on climate change due to emissions from thermal oxidation of polymeric materials present in the ASR fraction. A net environmental performance upgrading seems to be ensured by scenario 3, mainly due to replacing fossil fuel by solid recovered fuel.

Conclusions

The proposed additional dismantling of ELV (scenario 3) not only brings environmental benefits but also meets the European recovery and recycling targets. The associated increase of dismantling costs can be compensated by the additional recycling material revenues as well as social benefits by a rise in employment.     

Metabolic response of bluegill to exercise at low water temperature: implications for angling conservation

The metabolic response of fish to exercise is highly dependent on environmental factors such as temperature. In addition to natural challenges that force exercise (foraging, avoiding predators, etc.), sportfish species are also subjected to exercise when they are hooked by anglers, leading to metabolic energy costs that may impact fitness. While several studies have examined the physiological response of fish to capture in warm conditions, little work has examined this response under cold winter conditions when fish are targeted by ice-anglers. To fill this gap, we examined the metabolic impacts of exercise duration and air exposure on bluegill, Lepomis macrochirus, at a temperature typical for ice angling. Thirty-two bluegill were subjected to a simulated angling session which included either a light (30 s) or exhaustive exercise procedure, followed by either 30 s or 4 min of air exposure. Fish were then assessed at 5 °C for the following metabolic metrics using intermittent-flow respirometry: standard metabolic rate (SMR), maximum metabolic rate (MMR), aerobic scope (AS), recovery time, and excess post-exercise oxygen consumption (EPOC). Fish exercised to exhaustion had higher EPOC compared to lightly exercised fish, however EPOC was not affected by air exposure time. No other metrics were impacted by air exposure or exercise duration. These results are directly applicable to physiological outcomes for fish captured by ice-anglers during the winter and suggest that both low temperatures and low durations of exercise serve to keep metabolic costs low for fish angled during the winter months.     

Developmental and physiological challenges of octopus (Octopus vulgaris) early life stages under ocean warming

The ability to understand and predict the effects of ocean warming (under realistic scenarios) on marine biota is of paramount importance, especially at the most vulnerable early life stages. Here we investigated the impact of predicted environmental warming (+3 °C) on the development, metabolism, heat shock response and antioxidant defense mechanisms of the early stages of the common octopus, Octopus vulgaris. As expected, warming shortened embryonic developmental time by 13 days, from 38 days at 18 °C to 25 days at 21 °C. Concomitantly, survival decreased significantly (~29.9 %). Size at hatching varied inversely with temperature, and the percentage of smaller premature paralarvae increased drastically, from 0 % at 18 °C to 17.8 % at 21 °C. The metabolic costs of the transition from an encapsulated embryo to a free planktonic form increased significantly with warming, and HSP70 concentrations and glutathione S-transferase activity levels were significantly magnified from late embryonic to paralarval stages. Yet, despite the presence of effective antioxidant defense mechanisms, ocean warming led to an augmentation of malondialdehyde levels (an indicative of enhanced ROS action), a process considered to be one of the most frequent cellular injury mechanisms. Thus, the present study provides clues about how the magnitude and rate of ocean warming will challenge the buffering capacities of octopus embryos and hatchlings’ physiology. The prediction and understanding of the biochemical and physiological responses to warmer temperatures (under realistic scenarios) is crucial for the management of highly commercial and ecologically important species, such as O. vulgaris.     

Profitability of Willow Biomass Crops Affected by Incentive Programs

The economics of willow biomass crops are strongly influenced by yield, production, and harvesting costs and the delivered price for biomass. Under current management practices, willow biomass crops with yields of 12 oven-dried metric tons (odt)?ha^?1 year^?1 and a delivered price of $60 odt^?1 have an internal rate of return (IRR) of about 5.5 %. Yields below 9 odt ha^?1 year^?1 have an IRR <0 %. We examined the impact of different incentive programs on the returns from willow biomass crops and the hectares or tons of willow biomass supported across a range of yields. Incentive programs examined included establishment grants (EG), annual payments (AIP), low cost startup loans, and matching payments offered by two existing programs, the Conservation Resource Program (CRP) and more recently the Biomass Crop Assistance Program (BCAP). EGs covering 75 % of the establishment costs provide high returns for growers on medium to high-productivity sites. Stand-alone AIPs with payments of $124 ha^?1 year^?1 paid over 5–15 years had little impact on profitability for growers but were costly for a funding agency. Low-cost loans with an interest rate of 2–4 % are one of the least expensive approaches ($1.3–6.6 odt^?1) and improve profitability for medium- and high-yielding (8–16 odt ha^?1 year^?1) sites. A matching payment incentive providing $50 per odt delivered was the only individual incentive approach that made low-yielding sites (6 odt ha^?1 year^?1) profitable but was costly per odt compared to other incentives. Current CRP incentives made willow profitable across all productivity scenarios. The BCAP program generates higher profits for all productivity scenarios but comes at a higher cost. Effective financial incentives need to be well designed and monitored so that the target audience is reached and the intended policy goals are attained.     

Modulation of Habitat-Based Conservation Plans by Fishery Opportunity Costs: A New Caledonia Case Study Using Fine-Scale Catch Data

Numerous threats impact coral reefs and conservation actions are urgently needed. Fast production of marine habitat maps promotes the use of habitat-only conservation plans, where a given percentage of the area of each habitat is set as conservation objectives. However, marine reserves can impact access to fishing grounds and generate opportunity costs for fishers that need to be minimized. In New Caledonia (Southwest Pacific), we used fine-scale fishery catch maps to define nineteen opportunity costs layers (expressed as biomass catch loss) considering i) total catches, ii) target fish families, iii) local marine tenure, and iv) gear type. The expected lower impacts on fishery catch when using the different cost constraints were ranked according to effectiveness in decreasing the costs generated by the habitat-only scenarios. The exercise was done for two habitat maps with different thematic richness. In most cases, habitat conservation objectives remained achievable, but effectiveness varied widely between scenarios and between habitat maps. The results provide practical guidelines for coral reef conservation and management. Habitat-only scenarios can be used to initiate conservation projects with stakeholders but the costs induced by such scenarios can be lowered by up to 50–60% when detailed exhaustive fishery data are used. When using partial data, the gain would be only in the 15–25% range. The best compromises are achieved when using local data.     

All Washed Out? Foliar Nutrient Resorption and Leaching in Senescing Switchgrass

Ideal bioenergy feedstocks are low in nutrients that act as anti-quality factors during conversion processes. Research has shown that delaying harvest of temperate perennial grasses until late winter reduces nutrient content, primarily due to end-season resorption, but also indicates a role for foliar nutrient leaching. While end-season resorption has been estimated, foliar nutrient leaching has not, and is a factor that could refine harvest recommendations. Additionally, establishing a baseline of mineral loss during switchgrass senescence will improve our understanding of leaf-level nutrient resorption. Therefore, we applied simulated rainfall to replicated (n = 5) plots within a previously established switchgrass stand to determine if heavy precipitation can induce nutrient leaching in senescing, unharvested foliage. Hour-long simulated rainfalls of ～120 mm were applied every 2 weeks from early September to a killing frost in 2014 and 2015. Leaf samples were taken from the upper and lower canopy before and after simulated rainfalls and from no-rain controls and analyzed for elemental N, P, K, S, Mg, and Ca. Nutrient resorption estimates ranged from 33 to 82% in control plots. Comparison of rainfall plots to controls indicated that lower canopy leaves, upon reaching ≥50% senescence, were slightly susceptible to foliar nutrient leaching, with losses ranging from 0.3 to 2.8 g kg^?1 dry matter for K, P, and Mg. Nitrogen, Ca, and S were not susceptible to foliar leaching. Although statistically significant (P ≤ 0.05), these values suggested that foliar leaching was not a strong driver of nutrient loss during senescence.     

Soil-nutrient availability and the nutrient-use efficiencies of forests along an altitudinal gradient on Yakushima Island,Japan

The vegetation on Yakushima Island, Japan, grows on soils derived from Akahoya volcanic ash, released from the Kikai Caldera about 7300 years ago. The eruption was devastating and it is believed that primary succession and soil formation reinitiated across all altitudes at this point. We hypothesize that the concentrations of soil total phosphorus (P) and labile P fractions increase with increasing altitude because the soil formation has progressed less in upslope areas as a result of the cooler temperature and because of the ample P source of the volcanic ash. Conversely, we hypothesize that the concentration of soil inorganic nitrogen (N) decreases with increasing altitude. Available soil P and N would result in increasing P limitation downslope and increasing N limitation upslope, respectively. We studied soil P fractions and soil inorganic N, and P- and N-use efficiencies of the seven forests on Yakushima along an elevation gradient (170–1550 m a.s.l.). Contrary to our hypotheses, soil total P, labile soil P fractions, and inorganic N decreased with increasing altitude. The P- and N-use efficiencies of the forests were negatively correlated with the concentration of soil total active P (total P minus occluded P) and inorganic N, respectively. We suggest that progressive soil acidity and slower decomposition under cooler and wetter environments upslope must have dissolved the P contained in volcanic ash and accelerated P leaching. Forest ecosystems on Yakushima that show a distinct altitudinal zonation are, therefore, characterized by increasing P and N shortage with increasing altitude.     

Optimization of Microbial Leaching of Base Metals from a South African Sulfidic Nickel Ore Concentrate by Acidithiobacillus ferrooxidans

X-ray diffraction analysis revealed that pentlandite and chalcopyrite were the prominent mineral phases in a South African sulfidic nickel ore concentrate that hosted nickel and copper. Cobalt was found to be closely associated with the nickel-bearing pentlandite phase of the ore sample. Microbial batch leaching experiments designed according to a central composite design model were run for 15 days in a shaking incubator (150 rpm) at a constant temperature (30°C) with variations in experimental parameters like ore pulp density, particle size, bacterial inoculum, pH of the culture medium, and residence time. Quadratic mathematical models were developed to predict the rate of metal extractions. The suitability of the model of the microbial leaching process was confirmed from normal probability curves. An analysis of variance indicated that the residence time, pulp density of the ore, and particle size were the most significant factors. Bacterial inoculum size hardly showed any effect on the total metal extractions. Maximum nickel (82%), cobalt (76%) and copper (25.6%) extractions were achieved under optimum conditions, operated for 15 days at pulp density of 2% and particle size of ?75 µm at pH 1.5.     

Management of Warm- and Cool-Season Grasses for Biomass on Marginal Lands: II. Composition and Nutrient Balance

Organic fertilizers can improve soil health while providing nutrients for perennial grass growth for bioenergy feedstock, particularly under marginal soil conditions. The impact of organic fertilizer application on perennial grass composition needs clarification. Our objective was to evaluate feedstock composition, and N, P, and K dynamics of switchgrass (Panicum virgatum L.), tall fescue [Lolium arundinaceum (Schreb.)], and reed canarygrass (Phalaris arundinacea L.) provided with either inorganic or organic fertilizer sources. Grasses were established on a sandy soil and a clay soil at the Cornell University Willsboro Research Farm in Willsboro, NY. The experiment was a split-split plot randomization of a randomized block design with six replicates. Sites were whole plots, grass species were subplots, and fertility treatments were sub-subplots. Six treatments were (1) 168 kg ha^?1 of N fertilizer for cool-season grasses; 84 kg ha^?1 for switchgrass, (2) 56 kg ha^?1 of 0-46-0 P fertilizer plus N (#1), (3) 112 kg ha^?1 of 0-0-60 K fertilizer plus N (#1), (4) 89.6 Mg dairy manure ha^?1, (5) 44.8 Mg dairy manure compost ha^?1, and (6) a control without fertilizer. Organic fertilizers produced a net positive P and K balance, while other treatments had negative balances. Organic fertilizer treatments resulted in lower lignin and gross energy values, and higher total ash and Cl, compared to inorganic fertilizer treatments. Switchgrass biomass had higher fiber and gross energy, lower total ash, and much lower Cl content under organic fertilizer applications than cool-season grasses, making switchgrass a more desirable feedstock regardless of conversion process.