Activated carbons from waste biomass by sulfuric acid activation and their use on methylene blue adsorption

Preparation of the activated carbons from sunflower oil cake by sulphuric acid activation with different impregnation ratios was carried out. Laboratory prepared activated carbons were used as adsorbents for the removal of methylene blue (MB) from aqueous solutions. Liquid-phase adsorption experiments were conducted and the maximum adsorption capacity of each activated carbon was determined. The effects of various process parameters i.e., temperature, pH, initial methylene blue concentration, contact time on the adsorption capacity of each activated carbon were investigated. The kinetic models for MB adsorption onto the activated carbons were studied. Langmuir isotherm showed better fit than Freundlich isotherm for all activated carbon samples. The rates of adsorption were found to conform to the pseudo-second-order kinetics with good correlation. The separation factor (R(L)) revealed the favorable nature of the isotherm of the MB activated carbon system.     

Study on the removal of pesticide in agricultural run off by granular activated carbon

In this batch study, the adsorption of malathion by using granular activated carbon with different parameters due to the particle size, dosage of carbons, as well as the initial concentration of malathion was investigated. Batch tests were carried out to determine the potential and the effectiveness of granular activated carbon (GAC) in removal of pesticide in agricultural run off. The granular activated carbon; coconut shell and palm shells were used and analyzed as the adsorbent material. The Langmuir and Freundlich adsorption isotherms models were applied to describe the characteristics of adsorption behavior. Equilibrium data fitted well with the Langmuir model and Freundlich model with maximum adsorption capacity of 909.1 mg/g. The results indicate that the GAC could be used to effectively adsorb pesticide (malathion) from agricultural runoff.     

Vinyl imidazole carrying metal-chelated beads for reversible use in yeast invertase adsorption

Poly(ethylene glycol dimethacrylate-n-vinyl imidazole) [poly(EGDMA–VIM)] hydrogel (average diameter 150–200 μm) was prepared copolymerizing ethylene glycol dimethacrylate (EGDMA) with n-vinyl imidazole (VIM). Poly(EGDMA–VIM) beads had a specific surface area of 59.8 m²/g. Poly(EGDMA–VIM) beads were characterized by swelling studies and scanning electron microscope (SEM). Cu²⁺ ions were chelated on the poly(EGDMA–VIM) beads (452 μmol Cu²⁺/g), then the metal-chelated beads were used in the adsorption of yeast invertase in a batch system. The maximum invertase adsorption capacity of the poly(EGDMA–VIM)–Cu²⁺ beads was observed as 35.2 mg/g at pH 4.5. The adsorption isotherm of the poly(EGDMA–VIM)–Cu²⁺ beads can be well fitted to the Langmuir model. Adsorption kinetics data were tested using pseudo-first- and -second-order models. Kinetic studies showed that the adsorption followed a pseudo-second-order reaction. The value of the Michaelis constant K_m of invertase was significantly larger upon adsorption, indicating decreased affinity by the enzyme for its substrate, whereas V_max was smaller for the adsorbed invertase. The optimum temperature for the adsorbed preparation of poly(EGDMA–VIM)–Cu²⁺-invertase at 50 °C, 10 °C higher than that of the free enzyme at 40 °C. Storage stability was found to increase with adsorption. Adsorbed invertase retains an activity of 82% after 10 batch successive reactions, demonstrating the usefulness of the enzyme-loaded beads in biocatalytic applications.     

Adsorption of Cd(II) ions from aqueous solutions using activated carbon prepared from olive stone by ZnCl2 activation

This study is aimed to remove Cd(II) ions from aqueous solutions by adsorption. As adsorbent, activated carbon prepared from olive stone, an agricultural solid by-product was used. Different activating agent (ZnCl(2)) amounts and adsorbent particle size were studied to optimize adsorbent surface area. The adsorption experiments were conducted at different parameters such as, adsorbent dose, temperature, equilibrium time and pH. According to the experiments results, the equilibrium time, optimum pH, adsorbent dosage were found 60 min, pH > 6 and 1.0 g/50 ml respectively. The kinetic data supports pseudo-second order model and intra-particle model but shows very poor fit for pseudo-first order model. Adsorption isotherms were obtained from three different temperatures. These adsorption data were fitted with the Langmuir and Freundlich isotherms. In addition, the thermodynamic parameters, standard free energy (DeltaG(0)), standard enthalpy (DeltaH(0)), standard entropy (DeltaS(0)) of the adsorption process were calculated. To reveal the adsorptive characteristics of the produced active carbon, BET surface area measurements were made. Structural analysis was performed using SEM-EDS. The resulting activated carbons with 20% ZnCl(2) solution was the best sample of the produced activated carbons from olive stone with the specific surface area of 790.25 m(2)g(-1). The results show that the produced activated carbon from olive stone is an alternative low-cost adsorbent for removing Cd(II).     

The adsorption of copper(II) ions on to dehydrated wheat bran (DWB): determination of the equilibrium and thermodynamic parameters

The adsorption of copper(II) ions on to dehydrated wheat bran (DWB), a by-product of the flour process, was investigated as a function of initial pH, temperature, initial metal ion concentration and adsorbent dosage. The optimum adsorption conditions were initial pH 5.0, initial copper concentration 100 mg l⁻¹, temperature 60 °C and adsorbent dosage 0.1 g. The adsorption equilibrium was described well by the Langmuir isotherm model with maximum adsorption capacity of 51.5 mg g⁻¹ of copper(II) ions on DWB. The observation of an increase in adsorption with increasing temperature leads to the result that the adsorption of copper(II) ions on DWB is endothermic in nature. The thermodynamic parameters such as enthalpy, free energy and entropy changes were calculated and these values show that the copper(II)-DWB adsorption process was favoured at high temperatures.     

Adsorption of gold ions from industrial wastewater using activated carbon derived from hard shell of apricot stones - an agricultural waste

In this study, hard shell of apricot stones was selected from agricultural solid wastes to prepare effective and low cost adsorbent for the gold separation from gold-plating wastewater. Different adsorption parameters like adsorbent dose, particle size of activated carbon, pH and agitation speed of mixing on the gold adsorption were studied. The results showed that under the optimum operating conditions, more than 98% of gold was adsorbed onto activated carbon after only 3 h. The equilibrium adsorption data were well described by the Freundlich and Langmuir isotherms. Isotherms have been used to obtain thermodynamic parameters. Gold desorption studies were performed with aqueous solution mixture of sodium hydroxide and organic solvents at ambient temperatures. Quantitative recovery of gold ions is possible by this method. As hard shell of apricot stones is a discarded as waste from agricultural and food industries, the prepared activated carbon is expected to be an economical product for gold ion recovery from wastewater.     

Biosorption of Lead from Industrial Wastewater Using Chrysophyllum albidum Seed Shell

The shell of the seed of Chrysophyllum albidum carbon was used to adsorb lead (Pb) from aqueous solution, the sorption process with respect to its equilibria and kinetics as well as the effects of pH, contact time, adsorbent mass, adsorbate concentration, and particle size on adsorption were also studied. The most effective pH range was found to be between 4.5 and 5 for the sorption of the metal ion. The first-order rate equation by Lagergren was tested on the kinetic data and the adsorption process followed first-order rate kinetics. Isotherm data were analyzed for possible agreement with the Langmuir and Freundlich adsorption isotherms; the Freundlich and Langmuir models for dynamics of metal ion uptake proposed in this work fitted the experimental data reasonably well. However, equilibrium sorption data were better represented by Langmuir model than Freundlich. The adsorption capacity calculated from Langmuir isotherm was 72.1 mg Pb (II) g^{- 1} at initial pH of 5.0 at 30°C for the particle size of 1.00 to 1.25 mm with the use of 2.0 g/100 ml adsorbent mass. The structural features of the adsorbent were characterized by Fourier transform infrared (FTIR) spectrometry; the presence of hydroxyl, carbonyl, amide, and phosphate groups confirms the potential mechanism adsorption of the adsorbent. This readily available adsorbent is efficient in the uptake of Pb (II) ion in aqueous solution, thus, it could be an excellent alternative for the removal of heavy metals and organic matter from water and wastewater.     

Adsorption kinetics of a basic dye from aqueous solutions onto apricot stone activated carbon

The preparation of activated carbon from apricot stone with H₂SO₄ activation and its ability to remove a basic dye, astrazon yellow 7GL, from aqueous solutions were reported in this study. The adsorbent was characterized by FTIR, BET and SEM, respectively. The effects of various experimental parameters, such as initial dye concentration, pH, adsorbent dosage and temperature were investigated in a batch-adsorption technique. The optimum conditions for removal of the basic dye were found to be pH 10, 6 g/l of adsorbent dosage and equilibrium time of 35 min, respectively. A comparison of three kinetic models, the pseudo first-order, second-order and diffusion controlled kinetic models, on the basic dye-adsorbent system showed that the removal rate was heavily dependent on diffusion controlled kinetic models. The adsorption isotherm data were fitted well to Langmuir and Freundlich isotherms. The adsorption capacity was calculated as 221.23 mg/g at 50 °C. Thermodynamics parameters were also evaluated. The values of enthalpy and entropy were 49.87 kJ/mol and 31.93 J/mol K, respectively, indicating that this process was spontaneous and endothermic. The experimental studies were indicated that ASC had the potential to act as an alternative adsorbent to remove the basic dye from aqueous solutions.     

Removal of Cr(VI) from aqueous solutions by adsorption onto hazelnut shell activated carbon: kinetic and equilibrium studies

The adsorption Cr(VI) from aqueous solutions onto hazelnut shell activated carbon was carried out by varying the parameters such as pH, initial Cr(VI) concentration and temperature. The experimental data fitted well to the pseudo first-order kinetic model and then the rate constants were evaluated. The Langmuir isotherm provided the best correlation for Cr(VI) onto the activated carbon. Adsorption capacity was calculated from the Langmuir isotherm as 170 mg/g at an initial pH of 1.0 for the 1000 mg/l Cr(VI) solution. Thermodynamic parameters were evaluated and the adsorption is endothermic showing monolayer adsorption of Cr(VI).     

Application of Freundlich and Langmuir models to multistage purification process to remove heavy metal ions by using Schizomeris leibleinii

The adsorption of iron(III), lead(II) and cadmium(II) ions onto Schizomeris leibleinii, a green alga, was studied with respect to initial pH, temperature, initial metal ion and biomass concentration to determine the optimum adsorption conditions. Optimum initial pH for iron(III), lead(II) and cadmium(II) ions were 2.5, 4.5 and 5.0 at optimum temperature 30°C, respectively. The initial adsorption rates increased with increasing initial iron(III), lead(II) and cadmium(II) ion concentrations up to 100, 100 and 150 mg l⁻¹, respectively. The Freundlich and Langmuir adsorption isotherms were developed at various initial pH and temperature values. The adsorption of these metal ions to S. leibleinii was investigated in a two-stage mixed batch reactor. The residual metal ion concentrations (C_eq) at equilibrium at each stage for a given ‘quantity of dried algae (X₀)/volume of solution containing heavy metal ion (V₀)’ ratio were calculated using Freundlich and Langmuir isotherm constants. The experimental biosorption equilibrium data for iron(III), lead(II) and cadmium(II) ions were in good agreement with those calculated by both Freundlich and Langmuir models. The adsorbed iron(III), lead(II) and cadmium(II) ion concentrations increased with increasing X₀/V₀ ratios while the adsorbed metal quantities per unit mass of dried algae decreased.     

Adsorption of volatile organic compounds by pecan shell- and almond shell-based granular activated carbons

The objective of this research was to determine the effectiveness of using pecan and almond shell-based granular activated carbons (GACs) in the adsorption of volatile organic compounds (VOCs) of health concern and known toxic compounds (such as bromo-dichloromethane, benzene, carbon tetrachloride, 1,1,1-trichloromethane, chloroform, and 1,1-dichloromethane) compared to the adsorption efficiency of commercially used carbons (such as Filtrasorb 200, Calgon GRC-20, and Waterlinks 206C AW) in simulated test medium. The pecan shell-based GACs were activated using steam, carbon dioxide or phosphoric acid. An almond shell-based GAC was activated with phosphoric acid. Our results indicated that steam- or carbon dioxide-activated pecan shell carbons were superior in total VOC adsorption to phosphoric acid-activated pecan shell or almond shell carbons, inferring that the method of activation selected for the preparation of activated carbons affected the adsorption of VOCs and hence are factors to be considered in any adsorption process. The steam-activated, pecan shell carbon adsorbed more total VOCs than the other experimental carbons and had an adsorption profile similar to the two coconut shell-based commercial carbons, but had greater adsorption than the coal-based commercial carbon. All the carbons studied adsorbed benzene more effectively than the other organics. Pecan shell, steam-activated and acid-activated GACs showed higher adsorption of 1,1,1-trichloroethane than the other carbons studied. Multivariate analysis was conducted to group experimental carbons and commercial carbons based on their physical, chemical, and adsorptive properties. The results of the analysis conclude that steam-activated and acid-activated pecan shell carbons clustered together with coal-based and coconut shell-based commercial carbons, thus inferring that these experimental carbons could potentially be used as alternative sources for VOC adsorption in an aqueous environment.     

Adsorption of Phenolic Compounds and Methylene Blue onto Activated Carbon Prepared from Date Fruit Pits

Activated carbon has been prepared from date fruit pits. The carbon, prepared at different burn‐off rates, showed a high uptake of methylene blue. At 92 % burn‐off (weight loss percent of the carbonized pits upon activation), methylene blue uptake was 590 mg/g. With this high capacity, the carbon was then used to study the adsorption of phenol, 2‐nitrophenol, 2,4‐dinitrophenol, and 2,4,6‐trinitrophenol. The prepared activated carbon showed an adsorption capacity better than that of many activated carbons in current use. The experimental adsorption data for the single components were regressed using both Langmuir and Freundlich isotherm models and the fit was generally satisfactory. The experimental adsorption data of the binary system phenol‐2‐nitrophenol were compared with the predicted results using two predictive models: the generalized Langmuir and the IAS models. The data were better represented by the IAS theory than the generalized Langmuir model even though the fit of the experimental data was not adequate.     

Removal of molybdate from water by adsorption onto ZnCl2 activated coir pith carbon

Removal and recovery of molybdate from aqueous solution was investigated using ZnCl2 activated carbon developed from coir pith. Studies were conducted to delineate the effects of contact time, adsorbent dose, molybdate concentration, pH and temperature. Two theoretical adsorption isotherms, namely, Langmuir and Freundlich were used to describe the experimental results. The Langmuir adsorption capacity (Q0) was found to be 18.9 mg molybdate/g of the adsorbent. Adsorption followed second order kinetics. Studies were performed at different pH values to find out the pH at which maximum adsorption occurred. The pH effect and desorption studies showed that ion exchange and chemisorption mechanism were involved in the adsorption process. Thermodynamic parameters such as DeltaG0, DeltaH0 and DeltaS0 for the adsorption were evaluated. Effect of foreign ions on adsorption of molybdate has been examined. The results showed that ZnCl2 activated coir pith carbon was effective for the removal and recovery of molybdate from water.     

Characterization of mesoporous activated carbons prepared by pyrolysis of sewage sludge with pyrolusite

Activated carbons were prepared from sewage sludge by chemical activation. Pyrolusite was added as a catalyst during activation and carbonization. The influence of the mineral addition on the properties of the activated carbons produced was evaluated. The results show that activated carbons from pyrolusite-supplemented sewage sludge had up to a 75% higher BET surface area and up to a 66% increase in mesoporosity over ordinary sludge-based activated carbons. Batch adsorption experiments applying the prepared adsorbents to synthetic dye wastewater treatment yielded adsorption data well fitted to the Langmuir isotherm. The adsorbents from pyrolusite-supplemented sludges performed better in dye removal than those without mineral addition, with the carbon from pyrolusite-augmented sludge T2 presenting a significant increase in maximum adsorption capacity of 50 mg/g. The properties of the adsorbents were improved during pyrolusite-catalyzed pyrolysis via enhancement of mesopore production, thus the mesopore channels may provide fast mass transfer for large molecules like dyes.     

Dye adsorption by sewage sludge-based activated carbons in batch and fixed-bed systems

The present research work deals with the production of activated carbons by chemical activation and pyrolysis of sewage sludges. The adsorbent properties of these sewage sludges based activated carbons were studied by liquid-phase adsorption tests. Dyes removal from colored wastewater being a possible application for sludge based adsorbents, methylene blue and saphranine removing from solution was studied. Pure and binary adsorption assays were performed in batch and fixed bed systems. In all cases studied, the adsorbents produced from sewage sludges were able to adsorb both the compounds considered here. Nevertheless, time required for reaching equilibrium, adsorptive capacity and fixed bed characteristic parameters were different for these two compounds. Methylene blue adsorption occurred faster than that of saphranine, and it was preferably adsorbed when treating binary solutions. It could be concluded that the sewage sludge-based activated carbons may be promising for dyes removal from aqueous streams.     

Adsorptive removal of Pb(II) by activated carbon prepared from Spartina alterniflora: Equilibrium,kinetics and thermodynamics

Low-cost activated carbon was prepared from Spartina alterniflora by phosphoric acid activation for the removal of Pb(II) from dilute aqueous solution. The effect of experimental parameters such as pH, initial concentration, contact time and temperature on the adsorption was studied. The obtained data were fitted with the Langmuir and Freundlich equations to describe the equilibrium isotherms. The kinetic data were fitted with the Lagergren-first-order, pseudo-second-order and Elovich models. It was found that pH played a major role in the adsorption process. The maximum adsorption capacity for Pb(II) on S. alterniflora activated carbon (SAAC) calculated from Langmuir isotherm was more than 99 mg g⁻¹. The optimum pH range for the removal of Pb(II) was 4.8–5.6. The Freundlich isotherm model was found to best describe the experimental data. The kinetic rates were best fitted to the pseudo-second-order model. Thermodynamic study showed the adsorption was a spontaneous exothermic process.     

Production and comparison of high surface area bamboo derived active carbons

High surface area activated carbons have been produced from the natural biomaterial bamboo, using phosphoric acid as the activating agent. The effects of phosphoric acid impregnation ratio, activation temperature, heating rate on the carbon surface area, porosity and mass yield are presented. Three of these bamboo derived active carbons, surface areas 1337, 1628 and 2123m(2)/g were assessed for their ability to adsorb Acid Red 18 dye from aqueous solution; these results were compared with three conventional adsorbents: activated carbon F400, bone char and peat. Isotherm data were analysed using Langmuir, Freundlich, Redlich-Peterson and Langmuir-Freundlich isotherms. Different isotherms provided the best fit correlations to the adsorption experimental data but the Langmuir-Freundlich equation provided the best overall correlation of data. The adsorption capacities of two of the selected bamboo derived carbons were much greater than the capacities of the other three adsorbents.     

Lipase-catalyzed acylation of naringin with palmitic acid in highly concentrated homogeneous solutions

Acylation reactions of naringin with palmitic acid were performed by a lipase after formation of highly concentrated homogeneous solutions. Their initial naringin concentration was 840–950 mM, which is 20–60 times greater than that in organic solvent media. The overall productivity of highly concentrated solutions was more than 15 times greater than those of organic phase media. The addition of DMSO (20–40%, w/w) to substrate mixtures lowered the melting temperature of a naringin–palmitic acid mixture (1:1 molar ratio) to about 40 °C. Reactions at 80 °C apparently followed Michaelis–Menten kinetics despite extremely high substrate concentrations. As the temperature increased from 60 °C to 80 °C, the apparent viscosity of the highly concentrated solution decreased remarkably from 4.31 Pa s to 0.063 Pa s. An activation energy of 7.65 kcal/mol obtained in a range of 60–75 °C suggests a diffusion-control. On the other hand, an activation energy of 17.09 kcal/mol in a range of 75–90 °C indicates a reaction-control. The highest product conversion yield of 33% (mol/mol) was obtained in a 10 h reaction at 80 °C. Addition of activated molecular sieves to the highly concentrated solution increased the product conversion yield by 7% (mol/mol), suggesting that the original equilibrium was disrupted by removing water and then a new equilibrium was reached.     

Fast separation of bromelain by polyacrylic acid-bound iron oxide magnetic nanoparticles

The adsorption of bromelain from an aqueous solution by polyacrylic acid (PAA)-bound iron oxide magnetic nanoparticles was studied. The magnetic composite nanoparticles were shown to be efficient for the separation of bromelain. Except at pH <3, the adsorption of bromelain increased with the decrease in solution pH and reached almost 100% at pH 3–5. The adsorbed bromelain could be desorbed by the addition of KCl and complete desorption was achieved at pH 7 when [KCl]>0.6 M. The adsorption behaviour followed the Langmuir isotherm with a maximum adsorption amount of 0.476 mg/mg and a Langmuir adsorption equilibrium constant of 58.4 ml/mg at pH 4 and 0.1 M phosphate. In addition, it was notable that both the adsorption and desorption of bromelain were quite fast and could be completed in about 1 min due to the absence of internal diffusion resistance. Bromelain retained 87.4% activity after adsorption/desorption.     

Adsorption of Neutral Red onto Mn-impregnated activated carbons prepared from Typha orientalis

Activated carbon was prepared from an inexpensive and renewable carbon source, Typha orientalis, by H(3)PO(4) activation and then impregnated with different Mn salts and tested for its Neutral Red (NR) adsorption capacities. The amount of Mn impregnated in the activated carbon was influenced by the anion species. Impregnation with Mn decreased the surface area, changed the pore size and crystal structure, and introduced more acidic functional groups such as carboxyl, lactone and phenol groups. The optimum adsorption performance for all the activated carbons was obtained at pH 3.7, Mn-Carbon dose of 0.100g/100ml solution and contact time 4.5h. The adsorption isotherms fit the Langmuir isotherm equation. The kinetic data followed the pseudo-second-order model. The thermodynamic parameters indicated that the processes were spontaneous and endothermic. According to these results, the prepared Mn modified activated carbons are promising adsorbents for the removal of Neutral Red from wastewater.