Analysis of micromolar concentrations of glucose by an interference free flow injection based biosensor

A fast, sensitive, interference-free, single enzyme single reagent glucose biosensor, operated in flow injection analysis (FIA) mode, was developed. The method used involved formation of colored complex of titanium sulfate reagent with the peroxide generated by glucose oxidase immobilized in a packed bed reactor. The color developed was detected spectrophotometrically in a flow cuvette. The system could measure down to 0.5 mg glucose l^–1 and the response was reproducible and linear in the range 1 mg l^–1 to 100 mg l^–1. The analysis time for a 500 l sample was 35 s and was free of interference from a number of substances tested. Analysis results using an off-line batch kit were observed to be in agreement with the developed system for determination of glucose in blood plasma samples.     

Fed-batch production of <Emphasis Type="SmallCaps">d</Emphasis>-ribose from sugar mixtures by transketolase-deficient <Emphasis Type="Italic">Bacillus subtilis</Emphasis> SPK1

d-Ribose, a five-carbon sugar, is used as a key intermediate for the production of various biomaterials, such as riboflavin and inosine monophosphate. A high d-ribose-producing Bacillus subtilis SPK1 strain was constructed by the chemical mutation of the transketolase-deficient strain, B. subtilis JY1. Batch fermentation of B. subtilis SPK1 with 20 g l^–1 xylose and 20 g l^–1 glucose resulted in 4.78 g l^–1 dry cell mass, 23.0 g l^–1d-ribose concentration, and 0.72 g l^–1 h^–1 productivity, corresponding to a 1.5- to 1.7-fold increase when compared with values for the parental strain. A late-exponential phase was chosen as the best point for switching to a fed-batch process. Optimized fed-batch fermentation of B. subtilis SPK1, feeding a mixture of 200 g l^–1 xylose and 50 g l^–1 glucose after the late-exponential phase reduced the residual xylose and glucose concentrations to less than 7.0 g l^–1 and gave the best results of 46.6 g l^–1d-ribose concentration and 0.88 g l^–1 h^–1 productivity which were 2.0- and 1.2-fold higher than the corresponding values in a simple batch fermentation.     

Lactic acid fermentation by Lactobacillus casei in free cell form and immobilised on gluten pellets

A comparative study of the fermentation of a range of carbohydrate substrates, at various temperatures, was carried out using a commercial Lactobacillus casei strain in a free cell form and immobilised on gluten pellets. This strain required yeast extract, l-cysteine HCl and Mn²⁺ at 5, 0.5 and 0.1 g l^–1, respectively, for maximum growth and lactic acid production. Sugar fermentation using free cells showed preference in the order glucose, sucrose, fructose while lactose was poorly utilised. Optimum temperature for growth and lactic acid production over (18–30 h) was 43 °C. L. casei was successfully immobilised on gluten pellets and fermented glucose and sucrose in a shorter time (18 h) with increased lactic acid production (42 and 41 g l^–1 on glucose and sucrose, respectively).     

Lactic acid production from cellulosic waste by immobilized cells of Lactobacillus delbrueckii

Industrial waste corn cob residue (from xylose manufacturing) without pretreatment was hydrolyzed by cellulase and cellobiase. The cellulosic hydrolysate contained 52.4 g l⁻¹ of glucose and was used as carbon source for lactic acid fermentation by cells of Lactobacillus delbrueckii ZU-S2 immobilized in calcium alginate gel beads. The final concentration of lactic acid and the yield of lactic acid from glucose were 48.7 g l⁻¹ and 95.2%, respectively, which were comparative to the results of pure glucose fermentation. The immobilized cells were quite stable and reusable, and the average yield of lactic acid from glucose in the hydrolysate was 95.0% in 12 repeated batches of fermentation. The suitable dilution rate of continuous fermentation process was 0.13 h⁻¹, and the yield of lactic acid from glucose and the productivity were 92.4% and 5.746 g l⁻¹ h⁻¹, respectively. The production of lactic acid by simultaneous saccharification and fermentation (SSF) process was carried out in a coupling bioreactor, the final concentration of lactic acid was 55.6 g l⁻¹, the conversion efficiency of lactic acid from cellulose was 91.3% and the productivity was 0.927 g l⁻¹ h⁻¹. By using fed-batch technique in the SSF process, the final concentration of lactic acid and the productivity increased to 107.6 g l⁻¹ and 1.345 g l⁻¹ h⁻¹, respectively, while the dosage of cellulase per gram substrate decreased greatly. This research work should advance the bioconversion of renewable cellulosic resources and reduce environmental pollution.     

Selective production of bikaverin in a fluidized bioreactor with immobilized Gibberella fujikuroi

The best culture medium composition for the production of bikaverin by Gibberella fujikuroi in shake-flasks, i.e. 100 g glucose l^–1; 1 g NH₄Cl l^–1; 2 g rice flour l^–1; 5 g KH₂PO₄ l^–1 and 2.5 g MgSO₄ l^–1, was obtained through a fractional factorial design and then scaled-up to a fluidized bioreactor. The effects of carbon and nitrogen concentrations, inoculum size, aeration, flow rate and bead sizes on batch bikaverin production using immobilized G. fujikuroi in a fluidized bioreactor were determined by an orthogonal experimental design. Concentrations of up to 6.83 g bikaverin l^–1 were obtained when the medium contained 100 g glucose l^–1 and 1 g NH₄Cl l^–1 with an inoculum ratio of 10% v/v, an aeration rate of 3 volumes of air per volume of medium min^–1, and a bead size of 3 mm. Based on dry weight, the bikaverin production was 30–100 times larger than found in submerged culture and approximately three times larger than reported for solid substrate fermentation.     

Direct alcoholic fermentation of starchy biomass using amylolytic yeast strains in batch and immobilized cell systems

Summary Direct alcoholic fermentation of dextrin or soluble starch with selected amylolytic yeasts was studied in both batch and immobilized cell systems. In batch fermentations, Saccharomyces diastaticus was capable of fermenting high dextrin concentrations much more efficiently than Schwanniomyces castellii. From 200 g·l^–1 of dextrin S. diastaticus produced 77 g·l^–1 of ethanol (75% conversion efficiency). The conversion efficiency decreased to 59% but a higher final ethanol concentration of 120 g·l^–1 was obtained with a medium containing 400 g·l^–1 of dextrin. With a mixed culture of S. diastaticus and Schw. castellii 136 g·l^–1 of ethanol was produced from 400 g·l^–1 of dextrin (67% conversion efficiency). S. diastaticus cells attached well to polyurethane foam cubes and a S. diastaticus immobilized cell reactor produced 69 g·l^–1 of ethanol from 200 g·l^–1 of dextrin, corresponding to an ethanol productivity of 7.6g·l^–1·h^–1. The effluent from a two-stage immobilized cell reactor with S. diastaticus and Endomycopsis fibuligera contained 70 g·l^–1 and 80 g·l^–1 of ethanol using initial dextrin concentrations of 200 and 250 g·l^–1 respectively. The corresponding values for ethanol productivity were 12.7 and 9.6 g·l^–1·h^–1. The productivity of the immobilized cell systems was higher than for the batch systems, but much lower than for glucose fermentation.     

Batch propagation of Lactobacillus helveticus for production of lactic acid from lactose concentrated cheese whey with microaeration and nutrient supplementation

Continuous mix batch bioreactors were used to study the kinetic parameters of lactic acid fermentation in microaerated-nutrient supplemented, lactose concentrated cheese whey using Lactobacillus helveticus. Four initial lactose concentrations ranging from 50 to 150 g l^–1 were first used with no microaeration and no yeast extract added to establish the substrate concentration above which inhibition will occur and then the effects of microaeration and yeast extract on the process kinetic parameters were investigated. The experiments were conducted under controlled pH (5.5) and temperature (42 °C) conditions. The results indicated that higher concentrations of lactose had an inhibitory effect as they increased the lag period and the fermentation time; and decreased the specific growth rate, the maximum cell number, the lactose utilization rate, and the lactic acid production rate. The maximum lactic acid conversion efficiency (75.8%) was achieved with the 75 g l^–1 initial lactose concentration. The optimum lactose concentration for lactic acid production was 75 g l^–1 although Lactobacillus helveticus appeared to tolerate up to 100 g l^–1 lactose concentration. Since the lactic acid productivity is of a minor importance compared to lactic acid concentration when considering the economic feasibility of lactic acid production from cheese whey using Lactobacillus helveticus, a lactose concentration of up to 100 g l^–1 is recommended. Using yeast extract and/or microaeration increased the cell number, specific growth rate, cell yield, lactose consumption, lactic acid utilization rate, lactic acid concentration and lactic acid yield; and reduced the lag period, fermentation time and residual lactose. Combined yeast extract and microaeration produced better results than each one alone. From the results it appears that the energy uncoupling of anabolism and catabolism is the major bottleneck of the process. Besides lactic acid production, lactose may also be hydrolysed into glucose and galactose. The -galactosidase activity in the medium is caused by cell lysis during the exponential growth phase. The metabolic activities of Lactobacillus helveticus in the presence of these three sugars need further investigation.     

L-Lactic acid production from raw cassava starch in a circulating loop bioreactor with cells immobilized in loofa (Luffa cylindrica)

l-Lactic acid was produced from raw cassava starch, by simultaneous enzyme production, starch saccharification and fermentation in a circulating loop bioreactor with Aspergillus awamori and Lactococcus lactis spp. lactis immobilized in loofa sponge. A. awamori was immobilized directly in cylindrical loofa sponge while the L. lactis was immobilized in a loofa sponge alginate gel cube. In the loofa sponge alginate gel cube, the sponge serves as skeletal support for the gel with the cells. The alginate gel formed a hard outer layer covering the soft porous gel inside. By controlling the rate and frequency of broth circulation between the riser and downcomer columns, the riser could be maintained under aerobic condition while the downcomer was under anaerobic condition. Repeated fed-batch l-lactic acid production was performed for more than 400 h and the average lactic acid yield and productivity from raw cassava starch were 0.76 g lactic acid g^–1 starch and 1.6 g lactic acid l^–1 h^–1, respectively.     

The production of 2,3-butanediol by fermentation of high test molasses

Summary Klebsiella oxytoca fermented 199 g·l^–1 high test or invert molasses using batch fermentation with substrate shift to produce 95.2–98.6 g 2,3-butanediol·l^–1 and 2,4–4.3 g acetoin·l^–1 with a diol yield of 96–100% of the theoretical value and a diol productivity of 1.0–1.1 g·l^–1·h^–1. Fermentation was performed numerous times with molasses in repeated batch culture with cell recovery. Such repeated batch fermentation, in addition to a high product yield, also showed a very high product concentration. For example, 118 g 2,3-butanediol·l^–1 and 2.3 g acetoin·l^–1 were produced from 280 g·l^–1 of high test molasses. The diol productivity in this fermentation amounted to 2.4 g·l^–1·h^–1 and can undoubtedly be further increased by increasing the cell concentration. Because the Klebsiella cultures ferment 2,3-butanediol at an extremely high rate once the sugar has been consumed, the culture was inhibited completely by the addition of 15 g ethanol·l^–1 and switching off aeration. Offprint requests to: A. S. Afschar     

Acetone butanol ethanol (ABE) production from concentrated substrate: reduction in substrate inhibition by fed-batch technique and product inhibition by gas stripping

Acetone butanol ethanol (ABE) was produced in an integrated fed-batch fermentation-gas stripping product-recovery system using Clostridium beijerinckii BA101, with H₂ and CO₂ as the carrier gases. This technique was applied in order to eliminate the substrate and product inhibition that normally restricts ABE production and sugar utilization to less than 20 g l^–1 and 60 g l^–1, respectively. In the integrated fed-batch fermentation and product recovery system, solvent productivities were improved to 400% of the control batch fermentation productivities. In a control batch reactor, the culture used 45.4 g glucose l^–1 and produced 17.6 g total solvents l^–1 (yield 0.39 g g^–1, productivity 0.29 g l^–1 h^–1). Using the integrated fermentation-gas stripping product-recovery system with CO₂ and H₂ as carrier gases, we carried out fed-batch fermentation experiments and measured various characteristics of the fermentation, including ABE production, selectivity, yield and productivity. The fed-batch reactor was operated for 201 h. At the end of the fermentation, an unusually high concentration of total acids (8.5 g l^–1) was observed. A total of 500 g glucose was used to produce 232.8 g solvents (77.7 g acetone, 151.7 g butanol, 3.4 g ethanol) in 1 l culture broth. The average solvent yield and productivity were 0.47 g g^–1 and 1.16 g l^–1 h^–1, respectively.     

Lactic acid production by aggregated continuous cultures of Lactobacillus acidophilus under aerobic conditions

Summary The ability of Lactobacillus acidophilus to aggregate, to produce lactic acid for a long term continuous fermentation process and to exist as aggregate cell cultures in a gas-lift reactor under aerobic conditions was studied. The main product of fermentation was lactic acid and only the traces of other end-products were determined. The highest fermentation efficiency of lactic acid was 98.6% and the highest productivity was 9.6 g.l^–1.h^–1 of lactic acid.     

Amperometric estimation of BOD by using living immobilized yeasts

Summary A microbial electrode consisting of immobilized living whole cells of yeasts, porous membrane and an oxygen electrode was prepared for continuous estimation of biochemical oxygen demand (BOD). Immobilized Trichosporon cutaneum was employed for the microbial electrode sensor for BOD. When a sample solution containing the equivalent amount of glucose and glutamic acid was injected into the sensor system, the current of the electrode decreased markedly with time until steady state was reached. The response time was within 18 min. A linear relationship was observed between the current decrease and the concentration below 41 mg l ^– of glucose and 41 mg l ^– glutamic acid (5-day BOD 60 mg l ^–). The current decrease was reproducible within ± 6% of the relative error when a sample solution containing 27 mg l ^– of glucose and 27 mg l ^– of glutamic acid (5-day BOD 40 mg l ^–) was employed. The microbial electrode sensor was applied to untreated waste waters from a fermentation factory. Good comparative results were obtained between BOD estimated by the microbial electrode and that determined by the conventional 5-day method (regression coefficient was 1.2). Furthermore, the effect of various compounds on BOD estimation was also examined. The current output of the microbial electrode sensor was almost constant for 17 d and 400 tests.     

Optimization of lactic acid production by immobilized <Emphasis Type="Italic">Lactococcus lactis</Emphasis> IO-1

Production of lactic acid from glucose by immobilized cells of Lactococcus lactis IO-1 was investigated using cells that had been immobilized by either entrapment in beads of alginate or encapsulation in microcapsules of alginate membrane. The fermentation process was optimized in shake flasks using the Taguchi method and then further assessed in a production bioreactor. The bioreactor consisted of a packed bed of immobilized cells and its operation involved recycling of the broth through the bed. Both batch and continuous modes of operation of the reactor were investigated. Microencapsulation proved to be the better method of immobilization. For microencapsulated cells at immobilized cell concentration of 5.3 g l⁻¹, the optimal production medium had the following initial concentrations of nutrients (g l⁻¹): glucose 45, yeast extract 10, beef extract 10, peptone 7.5 and calcium chloride 10 at an initial pH of 6.85. Under these conditions, at 37 °C, the volumetric productivity of lactic acid in shake flasks was 1.8 g l⁻¹ h⁻¹. Use of a packed bed of encapsulated cells with recycle of the broth through the bed, increased the volumetric productivity to 4.5 g l⁻¹ h⁻¹. The packed bed could be used in repeated batch runs to produce lactic acid.     

2-Propanol degradation by Sulfolobus solfataricus

Sulfolobus solfataricus used 2-propanol and 2-propanone (acetone) when grown in static cultures at 78 °C with or without glucose at 10 g l^–1. The presence of 3.92 g 2-propanol l^–1 in both cases inhibited growth. However, acetone accumulation following 2-propanol depletion suggested that 2-propanol was co-metabolized via the acetone metabolic pathway. Glucose at 10 g l^–1 increased 2-propanol and acetone utilization from 0.93 g l^–1 to 1.77 g l^–1 and from 0.11 g l^–1 to 1.62 g l^–1, respectively. Without glucose, immobilized S. solfataricus cells increased the 2-propanol removal rate to 0.035 g l^–1 h^–1, compared to 0.0012 g l^–1 h^–1 by its suspended counterpart. The results suggest the establishment of an immobilized reactor configuration is preferential for the treatment of high temperature solvent waste streams by this acidothermophilic Crenarchaeon.     

Fermentative production of l-lactic acid by Lactobacillus casei DSM 20011 and product recovery using ion exchange resins

In order to produce l(+)-lactic acid to be employed in poly-l-lactic acid polymer production, for biomedical applications, the strain Lactobacillus casei subsp. casei DSM 20011 was studied in a conventional batch mode using different initial concentrations of glucose. The results obtained showed that the initial glucose concentration exerts an influence on the fermentation pattern, modifying the different fermentation parameters. Nevertheless, the product yield remained at a constant value of 0.86 g·g^–1. The proposed novel system of product recovery, based on the use of ion-exchange resins, gave high yields of pure lactic acid. Correspondence to: D. Matteuzzi     

Growth of Saccharomyces cerevisiae in a chemostat under high glucose conditions

Saccharomyces cerevisiae was grown in a chemostat under high glucose conditions (up to 300 g l^–1). The results support the view that higher glucose feed favors higher ethanol production regardless of the existence of osmotic stress. A low glucose utilization and yield coefficient provides an opportunity to improve continuous fermentation performance in the fuel alcohol industry. The possibility exists of reusing yeast cells and subsequently lower operating costs, and by using an optimal glucose feeding concentration between 100 and 200 g l^–1.     

Production of acetone,butanol and ethanol by Clostridium beijerinckii BA101 and in situ recovery by gas stripping

We examined the effect of gas-stripping on the in situ removal of acetone, butanol, and ethanol (ABE) from batch reactor fermentation broth. The mutant strain (Clostridium beijerinckii BA101) was not affected adversely by gas stripping. The presence of cells in the fermentation broth affected the selectivities of ABE. A considerable improvement in the productivity and yield was recorded in this work in comparison with the non-integrated process. In an integrated process of ABE fermentation-recovery using C. beijerinckii BA101, ABE productivities and yield were improved up to 200 and 118%, respectively, as compared to control batch fermentation data. In a batch reactor C. beijerinckii BA101 utilized 45.4 g glucose l^–1 and produced 17.7 g total ABE l^–1, while in the integrated process it utilized 161.7 g glucose l^–1 and produced total ABE of 75.9 g l^–1. In the integrated process, acids were completely converted to solvents when compared to the non-integrated process (batch fermentation) which contained residual acids at the end of fermentation. In situ removal of ABE by gas stripping has been reported to be one of the most important techniques of solvent removal. During these studies we were able to maintain the ABE concentration in the fermentation broth below toxic levels.     

Acid hydrolysis of sugarcane bagasse for lactic acid production

In order to use sugarcane bagasse as a substrate for lactic acid production, optimum conditions for acid hydrolysis of the bagasse were investigated. After lignin extraction, the conditions were varied in terms of hydrochloric (HCl) or sulfuric (H₂SO₄) concentration (0.5–5%, v/v), reaction time (1–5 h) and incubation temperature (90–120 °C). The maximum catalytic efficiency (E) was 10.85 under the conditions of 0.5% of HCl at 100 °C for 5 h, which the main components (in g l⁻¹) in the hydrolysate were glucose, 1.50; xylose, 22.59; arabinose, 1.29; acetic acid, 0.15 and furfural, 1.19. To increase yield of lactic acid production from the hydrolysate by Lactococcus lactis IO-1, the hydrolysate was detoxified through amberlite and supplemented with 7 g l⁻¹ of xylose and 7 g l⁻¹ of yeast extract. The main products (in g l⁻¹) of the fermentation were lactic acid, 10.85; acetic acid, 7.87; formic acid, 6.04 and ethanol, 5.24.     

Immobilization of -glucose oxidase onto a hydrogen peroxide permselective membrane and application for an enzyme electrode

A hydrogen peroxide permselective membrane with asymmetric structure was prepared and -glucose oxidase (EC 1.1.3.4) was immobilized onto the porous layer. The activity of the immobilized -glucose oxidase membrane was 0.34 units cm⁻² and the activity yield was 6.8% of that of the native enzyme. Optimum pH, optimum temperature, pH stability and temperature stability were found to be pH 5.0, 30–40°C, pH 4.0–7.0 and below 55°C, respectively. The apparent Michaelis constant of the immobilized -glucose oxidase membrane was 1.6 × 10⁻³ mol l⁻¹ and that of free enzyme was 4.8 × 10⁻² mol l⁻¹. An enzyme electrode was constructed by combination of a hydrogen peroxide electrode with the immobilized -glucose oxidase membrane. The enzyme electrode responded linearly to -glucose over the concentration 0–1000 mg dl⁻¹ within 10 s. When the enzyme electrode was applied to the determination of -glucose in human serum, within day precision (CV) was 1.29% for -glucose concentration with a mean value of 106.8 mg dl⁻¹. The correlation coefficient between the enzyme electrode method and the conventional colorimetric method using a free enzyme was 0.984. The immobilized -glucose oxidase membrane was sufficiently stable to perform 1000 assays (2 to 4 weeks operation) for the determination of -glucose in human whole blood. The dried membrane retained 77% of its initial activity after storage at 4°C for 16 months.     

Continuous solvent production by Clostridium beijerinckii BA101 immobilized by adsorption onto brick

The performance of a continuous bioreactor containing Clostridium beijerinckii BA101 adsorbed onto clay brick was examined for the fermentation of acetone, butanol, and ethanol (ABE). Dilution rates from 0.3 to 2.5 h^–1 were investigated with the highest solvent productivity of 15.8 g l^–1 h^–1 being obtained at 2.0 h^–1. The solvent yield at this dilution rate was found to be 0.38 g g^–1 and total solvent concentration was 7.9 g l^–1. The solvent yield was maximum at 0.45 at a dilution rate of 0.3 h^–1. The maximum solvent productivity obtained was found to be 2.5 times greater than most other immobilized continuous and cell recycle systems previously reported for ABE fermentation. A higher dilution rate (above 2.0 h^–1) resulted in acid production rather than solvent production. This reactor was found to be stable for over 550 h. Scanning electron micrographs (SEM) demonstrated that a large amount of C. beijerinckii cells were adsorbed onto the brick support.