Potential inhibitors from wet oxidation of wheat straw and their effect on ethanol production of Saccharomyces cerevisiae: wet oxidation and fermentation by yeast

Alkaline wet oxidation (WO) (using water, 6.5 g/L sodium carbonate and 12 bar oxygen at 195 degrees C) was used as pretreatment method for wheat straw (60 g/L), resulting in a hydrolysate and a cellulosic solid fraction. The hydrolysate consisted of soluble hemicellulose (8 g/L), low-molecular-weight carboxylic acids (3.9 g/L), phenols (0.27 g/L = 1.7 mM) and 2-furoic acid (0.007 g/L). The wet oxidized wheat straw hydrolysate caused no inhibition of ethanol production by Saccharomyces cerevisiae ATCC 96581. Nine phenols and 2-furoic acid, identified to be present in the hydrolysate, were each tested in concentrations of 50-100 times the concentration found in the hydrolysate for their effect on fermentation by yeast. At these high concentrations (10 mM), 4-hydroxybenzaldehyde, vanillin, 4-hydroxyacetophenone and acetovanillone caused a 53-67% decrease in the volumetric ethanol productivity in S. cerevisiae compared to controls with an ethanol productivity of 3.8 g/L. The phenol acids (4-hydroxy, vanillic and syringic acid), 2-furoic acid, syringaldehyde and acetosyringone were less inhibitory, causing a 5-16% decrease in ethanol productivity. By adding the same aromatic compounds to hydrolysate (10 mM), it was shown that syringaldehyde and acetovanillone interacted negatively with hydrolysate components on the ethanol productivity. Fermentation in WO hydrolysate, that had been concentrated 6 times by freeze-drying, lasted 4 hours longer than in regular hydrolysate; however, the ethanol yield was the same. The longer fermentation time could not be explained by an inhibitory action of phenols alone, but was more likely caused by inhibitory interactions of phenols with carboxylic acids, such as acetic and formic acid.     

Characterization of degradation products from alkaline wet oxidation of wheat straw

Alkaline wet oxidation pre-treatment (water, sodium carbonate, oxygen, high temperature and pressure) of wheat straw was performed as a 2(4-1) fractional factorial design with the process parameters: temperature, reaction time, sodium carbonate and oxygen. Alkaline wet oxidation was an efficient pre-treatment of wheat straw that resulted in solid fractions with high cellulose recovery (96%) and high enzymatic convertibility to glucose (67%). Carbonate and temperature were the most important factors for fractionation of wheat straw by wet oxidation. Optimal conditions were 10 min at 195 degrees C with addition of 12 bar oxygen and 6.5 g l(-1) Na2CO3. At these conditions the hemicellulose fraction from 100 g straw consisted of soluble hemicellulose (16 g), low molecular weight carboxylic acids (11 g), monomeric phenols (0.48 g) and 2-furoic acid (0.01 g). Formic acid and acetic acid constituted the majority of degradation products (8.5 g). The main phenol monomers were 4-hydroxybenzaldehyde, vanillin, syringaldehyde. acetosyringone (4-hydroxy-3,5-dimethoxy-acetophenone), vanillic acid and syringic acid, occurring in 0.04-0.12 g per 100 g straw concentrations. High lignin removal from the solid fraction (62%) did not provide a corresponding increase in the phenol monomer content but was correlated to high carboxylic acid concentrations. The degradation products in the hemicellulose fractions co-varied with the pre-treatment conditions in the principal component analysis according to their chemical structure, e.g. diacids (oxalic and succinic acids), furan aldehydes, phenol aldehydes, phenol ketones and phenol acids. Aromatic aldehyde formation was correlated to severe conditions with high temperatures and low pH. Apart from CO2 and water, carboxylic acids were the main degradation products from hemicellulose and lignin.     

Concentration-driven reverse membrane bioreactor for the fermentation of highly inhibitory lignocellulosic hydrolysate

Optimal production of lignocellulosic bioethanol is hindered due to commonly faced issues with the presence of inhibitory compounds and sequentially consumed sugars in the lignocellulosic hydrolysate. Therefore, in order to find a robust fermentation approach, this study aimed at enhancing simultaneous co-assimilation of sugars, and inhibitor tolerance and detoxification. Therefore, fermentation of toxic wheat straw hydrolysate containing up to 20 g/l furfural, using the concentration-driven diffusion-based technique of reverse membrane bioreactor (rMBR) was studied. The rMBR fermentation of the hydrolysate led to complete furfural detoxification and the conversion of 87 % of sugars into ethanol at a yield of 0.48 g/g. Moreover, when the toxicity level of the hydrolysate was increased to 9 g/l of initial furfural, the system responded exceptionally by reducing 89 % of the inhibitor while only experiencing about 25 % drop in the ethanol yield. In addition, using this diffusion-based set-up in extremely inhibitory conditions (16 g/l furfural), cells could detoxify 40 % of the furfural at a high initial furfural to cell ratio of 9.5:1. The rMBR set-up applied proved that by properly synchronizing the medium condition, membrane area, and inhibitor to cell ratio, some of the shortcomings with conventional lignocellulosic fermentation can be tackled, guaranteeing a robust fermentation.     

Effect of compounds released during pretreatment of wheat straw on microbial growth and enzymatic hydrolysis rates

In the process of producing ethanol from lignocellulosic materials such as wheat straw, compounds that can act inhibitory to enzymatic hydrolysis and to cellular growth may be generated during the pretreatment. Ethanol production was evaluated on pretreated wheat straw hydrolysate using four different recombinant Saccharomyces cerevisiae strains, CPB.CR4, CPB.CB4, F12, and FLX. The fermentation performance of the four S. cerevisiae strains was tested in hydrolysate of wheat straw that has been pretreated at high dry matter content (220 g/L dry matter). The results clearly showed that F12 was the most robust strain, whereas the other three strains were strongly inhibited when the fraction of hydrolysate in the fermentation medium was higher than 60% (v/v). Furthermore, the impact of different lignin derivatives commonly found in the hydrolysate of pretreated wheat straw, was tested on two different enzyme mixtures, a mixture of Celluclast 1.5 L FG and Novozym 188 (3:1) and one crude enzyme preparation produced from Penicillium brasilianum IBT 20888. From all the potential inhibiting compounds that were tested, formic acid had the most severe influence on the hydrolysis rate resulting in a complete inactivation of the two enzyme mixtures.     

Inhibition of ethanol-producing yeast and bacteria by degradation products produced during pre-treatment of biomass

An overview of the different inhibitors formed by pre-treatment of lignocellulosic materials and their inhibition of ethanol production in yeast and bacteria is given. Different high temperature physical pre-treatment methods are available to render the carbohydrates in lignocellulose accessible for ethanol fermentation. The resulting hydrolyzsates contain substances inhibitory to fermentation—depending on both the raw material (biomass) and the pre-treatment applied. An overview of the inhibitory effect on ethanol production by yeast and bacteria is presented. Apart from furans formed by sugar degradation, phenol monomers from lignin degradation are important co-factors in hydrolysate inhibition, and inhibitory effects of these aromatic compounds on different ethanol producing microorganisms is reviewed. The furans and phenols generally inhibited growth and ethanol production rate (Q_EtOH) but not the ethanol yields (Y_EtOH) in Saccharomyces cerevisiae. Within the same phenol functional group (aldehyde, ketone, and acid) the inhibition of volumetric ethanol productivity was found to depend on the amount of methoxyl substituents and hence hydrophobicity (log P). Many pentose-utilizing strains Escherichia coli, Pichia stipititis, and Zymomonas mobilis produce ethanol in concentrated hemicellulose liquors but detoxification by overliming is needed. Thermoanaerobacter mathranii A3M3 can grow on pentoses and produce ethanol in hydrolysate without any need for detoxification.     

Enhanced ethanol production from industrial lignocellulose hydrolysates by a hydrolysate-cofermenting Saccharomyces cerevisiae strain

Industrial production of lignocellulosic ethanol requires a microorganism utilizing both hexose and pentose, and tolerating inhibitors. In this study, a hydrolysate-cofermenting Saccharomyces cerevisiae strain was obtained through one step in vivo DNA assembly of pentose-metabolizing pathway genes, followed by consecutive adaptive evolution in pentose media containing acetic acid, and direct screening in biomass hydrolysate media. The strain was able to coferment glucose and xylose in synthetic media with the respective maximal specific rates of glucose and xylose consumption, and ethanol production of 3.47, 0.38 and 1.62 g/g DW/h, with an ethanol titre of 41.07 g/L and yield of 0.42 g/g. Industrial wheat straw hydrolysate fermentation resulted in maximal specific rates of glucose and xylose consumption, and ethanol production of 2.61, 0.54 and 1.38 g/g DW/h, respectively, with an ethanol titre of 54.11 g/L and yield of 0.44 g/g. These are among the best for wheat straw hydrolysate fermentation through separate hydrolysis and cofermentation.

     

Direct ethanol production from starch, wheat bran and rice straw by the white rot fungus Trametes hirsuta

The white rot fungus Trametes hirsuta produced ethanol from a variety of hexoses: glucose, mannose, cellobiose and maltose, with yields of 0.49, 0.48, 0.47 and 0.47 g/g of ethanol per sugar utilized, respectively. In addition, this fungus showed relatively favorable xylose consumption and ethanol production with a yield of 0.44 g/g. T. hirsuta was capable of directly fermenting starch, wheat bran and rice straw to ethanol without acid or enzymatic hydrolysis. Maximum ethanol concentrations of 9.1, 4.3 and 3.0 g/l, corresponding to 89.2%, 78.8% and 57.4% of the theoretical yield, were obtained when the fungus was grown in a medium containing 20 g/l starch, wheat bran or rice straw, respectively. The fermentation of rice straw pretreated with ball milling led to a small improvement in the ethanol yield: 3.4 g ethanol/20 g ball-milled rice straw. As T. hirsuta is an efficient microorganism capable of hydrolyzing biomass to fermentable sugars and directly converting them to ethanol, it may represent a suitable microorganism in consolidated bioprocessing applications.     

Influence of Medium Composition on Xylitol Bioproduction from Wheat Straw Hemicellulosic Hydrolysate

Summary Xylose-to-xylitol batch bioconversions from wheat straw hemicellulosic hydrolysate were carried out in Erlenmeyer flasks in order to assess the influence of medium composition (hydrolysate concentration, supplementation with ammonium sulphate, calcium chloride and rice bran extract, and initial pH) on xylitol production, productivity and yield. By using the screening design and the response surface methodologies, the statistically significant variables influencing the bioconversion were selected and linear models were fitted to the experimental data. According to the results, the best conditions to perform the bioconversion consisted in using a threefold concentrated hydrolysate supplemented with ammonium sulphate (1.0 g/l) and rice bran extract (5.0 g/l), whose pH was adjusted to 6.0 prior to inoculation. Under these conditions, a xylitol production of 24.17 g/l was observed after 72 h of fermentation, resulting in a productivity of 0.34 g/l h and in a bioconversion yield of 0.49 g/g.     

Ethanol fermentation of acid-hydrolyzed cellulosic pyrolysate with Saccharomyces cerevisiae

Acid-hydrolysis of cellulosic pyrolysate to glucose and its fermentation to ethanol were investigated. The maximum glucose yield (17.4%) was obtained by the hydrolysis with 0.2 mol/l sulfuric acid using autoclaving at 121 degrees C for 20 min. The fermentation by Saccharomyces cerevisiae of a hydrolysate medium containing 31.6 g/l glucose gave 14.2 g/l ethanol after 24 h, whereas the fermentation of the medium containing 31.6 g/l pure glucose gave 13.7 g/l ethanol after 18 h. The results showed that acid-hydrolyzed pyrolysate could be used for ethanol production. Different nitrogen sources were evaluated and the best ethanol concentration (15.1 g/l) was achieved by single urea. S. cerevisiae (R) was obtained by adaptation of S. cerevisiae to the hydrolysate medium for 12 times, and 40.2 g/l ethanol was produced by it in the fermentation with the hydrolysate medium containing 95.8 g/l glucose, which was about 47% increase in ethanol production compared to its parent strain.     

Ethanol fermentation of acid-hydrolyzed cellulosic pyrolysate with Saccharomyces cerevisiae

The acid hydrolysis of cellulosic pyrolysate to glucose and its fermentation to ethanol were investigated. The maximum glucose yield (17.4%) was obtained by the hydrolysis with 0.2 mol sulfuric acid per liter pyrolysate using autoclaving at 121 degrees C for 20 min. The fermentation by Saccharomyces cerevisiae of a hydrolysate medium containing 31.6 g/l glucose gave 14.2 g/l ethanol in 24 h, whereas the fermentation of the medium containing 31.6 g/l pure glucose gave 13.7 g/l ethanol in 18 h. The results showed that the acid-hydrolyzed pyrolysate could be used for ethanol production. Different nitrogen sources were evaluated and the best ethanol concentration (15.1 g/l) was achieved by single urea. S. cerevisiae (R) was obtained by adaptation of S. cerevisiae to the hydrolysate medium for 12 times, and 40.2 g/l ethanol was produced by S. cerevisiae (R) in the fermentation with the hydrolysate medium containing 95.8 g/l glucose, which was about 47% increase in ethanol production compared to its parent strain.     

Identification and characterization of fermentation inhibitors formed during hydrothermal treatment and following SSF of wheat straw

A pilot plant for hydrothermal treatment of wheat straw was compared in reactor systems of two steps (first, 80°C; second, 190–205°C) and of three steps (first, 80°C; second, 170–180°C; third, 195°C). Fermentation (SSF) with Sacharomyces cerevisiae of the pretreated fibers and hydrolysate from the two-step system gave higher ethanol yield (64–75%) than that obtained from the three-step system (61–65%), due to higher enzymatic cellulose convertibility. At the optimal conditions (two steps, 195°C for 6 min), 69% of available C6-sugar could be fermented into ethanol with a high hemicellulose recovery (65%). The concentration of furfural obtained during the pretreatment process increased versus temperature from 50 mg/l at 190°C to 1,200 mg/l at 205°C as a result of xylose degradation. S. cerevisiae detoxified the hydrolysates by degradation of several toxic compounds such as 90–99% furfural and 80–100% phenolic aldehydes, which extended the lag phase to 5 h. Acetic acid concentration increased by 0.2–1 g/l during enzymatic hydrolysis and 0–3.4 g/l during fermentation due to hydrolysis of acetyl groups and minor xylose degradation. Formic acid concentration increased by 0.5–1.5 g/l probably due to degradation of furfural. Phenolic aldehydes were oxidized to the corresponding acids during fermentation reducing the inhibition level.     

Butanol production by Clostridium beijerinckii ATCC 55025 from wheat bran

Wheat bran, a by-product of the wheat milling industry, consists mainly of hemicellulose, starch and protein. In this study, the hydrolysate of wheat bran pretreated with dilute sulfuric acid was used as a substrate to produce ABE (acetone, butanol and ethanol) using Clostridium beijerinckii ATCC 55025. The wheat bran hydrolysate contained 53.1 g/l total reducing sugars, including 21.3 g/l of glucose, 17.4 g/l of xylose and 10.6 g/l of arabinose. C. beijerinckii ATCC 55025 can utilize hexose and pentose simultaneously in the hydrolysate to produce ABE. After 72 h of fermentation, the total ABE in the system was 11.8 g/l, of which acetone, butanol and ethanol were 2.2, 8.8 and 0.8 g/l, respectively. The fermentation resulted in an ABE yield of 0.32 and productivity of 0.16 g l⁻¹ h⁻¹. This study suggests that wheat bran can be a potential renewable resource for ABE fermentation.     

The enzymatic hydrolysis and fermentation of pretreated wheat straw to ethanol

Autohydrolysis and ethanol-alkali pulping were used as pretreatment methods of wheat straw for its subsequent saccharification by Trichoderma reesei cellulase. The basic hydrolysis parameters, i.e., reaction time, pH, temperature, and enzyme and substrate concentration, were optimized to maximize sugar yields from ethanol-alkali modified straw. Thus, a 93% conversion of 2.5% straw material to sugar syrup containing 73% glucose was reached in 48 h using 40 filter paper units/g hydrolyzed substrate. The pretreated wheat straw was then fermented to ethanol at 43 degrees C in the simultaneous saccharification and fermentation (SSF) process using T. reesei cellulase and Kluyveromyces fragilis cells. From 10% (w/v) of chemically treated straw (dry matter), 2.4% (w/v) ethanol was obtained after 48 h. When the T. reesei cellulase system was supplemented with beta-glucosidase from Aspergillus niger, the ethanol yield in the SSF process increased to 3% (w/v) and the reaction time was shortened to 24 h.     

Fermentation of sugar cane bagasse hemicellulosic hydrolysate and sugar mixtures to ethanol by recombinant Escherichia coli KO11

Escherichia coli KO11, carrying the ethanol pathway genes pdc (pyruvate decarboxylase) and adh (alcohol dehydrogenase) from Zymomonas mobilis integrated into its chromosome, has the ability to metabolize pentoses and hexoses to ethanol, both in synthetic medium and in hemicellulosic hydrolysates. In the fermentation of sugar mixtures simulating hemicellulose hydrolysate sugar composition (10.0 g of glucose/l and 40.0 g of xylose/l) and supplemented with tryptone and yeast extract, recombinant bacteria produced 24.58 g of ethanol/l, equivalent to 96.4% of the maximum theoretical yield. Corn steep powder (CSP), a byproduct of the corn starch-processing industry, was used to replace tryptone and yeast extract. At a concentration of 12.5 g/l, it was able to support the fermentation of glucose (80.0 g/l) to ethanol, with both ethanol yield and volumetric productivity comparable to those obtained with fermentation media containing tryptone and yeast extract. Hemicellulose hydrolysate of sugar cane bagasse supplemented with tryptone and yeast extract was also readily fermented to ethanol within 48 h, and ethanol yield achieved 91.5% of the theoretical maximum conversion efficiency. However, fermentation of bagasse hydrolysate supplemented with 12.5 g of CSP/l took twice as long to complete. This revised version was published online in November 2006 with corrections to the Cover Date.     

Ethanol recovery from corn fiber hydrolysate fermentations by pervaporation

Corn fiber, a byproduct of corn wet milling, is an attractive feedstock for biomass ethanol production. Corn fiber was hydrolyzed by dilute sulfuric acid and neutralized by one of two methods: conventional lime treatment or neutralization by strongly basic anion exchange. The anion exchange neutralized (AEN) hydrolysate contained substantially lower levels of the inhibiting compounds furfural, 5-hydroxymethylfurfural, and acetic acid compared to the lime neutralized hydrolysate. In batch fermentations the ethanol yields and final ethanol concentration of the two hydrolysates were similar at 0.32-0.43 g/g and 29-44 g/l, respectively. Sugar consumption in the AEN fermentations was superior. Coupling of a membrane pervaporation unit to a fed-batch fermentation of AEN hydrolysate maintained the ethanol concentration below 25 g/l with complete sugar utilization for approximately 5 days. A concentrated ethanol stream of 17 wt.% ethanol was produced by the pervaporation unit.     

Ethanol production from corn cob hydrolysates by <Emphasis Type="Italic">Escherichia coli</Emphasis> KO11

Corn cob hydrolysates, with xylose as the dominant sugar, were fermented to ethanol by recombinant Escherichia coli KO11. When inoculum was grown on LB medium containing glucose, fermentation of the hydrolysate was completed in 163 h and ethanol yield was 0.50 g ethanol/g sugar. When inoculum was grown on xylose, ethanol yield dropped, but fermentation was faster (113 h). Hydrolysate containing 72.0 g/l xylose and supplemented with 20.0 g/l rice bran was readily fermented, producing 36.0 g/l ethanol within 70 h. Maximum ethanol concentrations were not higher for fermentations using higher cellular concentration inocula. A simulation of an industrial process integrating pentose fermentation by E. coli and hexose fermentation by yeast was carried out. At the first step, E. coli fermented the hydrolysate containing 85.0 g/l xylose, producing 40.0 g/l ethanol in 94 h. Baker's yeast and sucrose (150.0 g/l) were then added to the spent fermentation broth. After 8 h of yeast fermentation, the ethanol concentration reached 104.0 g/l. This two-stage fermentation can render the bioconversion of lignocellulose to ethanol more attractive due to increased final alcohol concentration. Journal of Industrial Microbiology & Biotechnology (2002) 29, 124–128 doi:10.1038/sj.jim.7000287 Received 20 February 2002/ Accepted in revised form 04 June 2002     

Optimization of a synthetic mixture composed of major Trichoderma reesei enzymes for the hydrolysis of steam-exploded wheat straw

Background

The commercialization of second-generation bioethanol has not been realized due to several factors, including poor biomass utilization and high production cost. It is generally accepted that the most important parameters in reducing the production cost are the ethanol yield and the ethanol concentration in the fermentation broth. Agricultural residues contain large amounts of hemicellulose, and the utilization of xylose is thus a plausible way to improve the concentration and yield of ethanol during fermentation. Most naturally occurring ethanol-fermenting microorganisms do not utilize xylose, but a genetically modified yeast strain, TMB3400, has the ability to co-ferment glucose and xylose. However, the xylose uptake rate is only enhanced when the glucose concentration is low.

Results

Separate hydrolysis and co-fermentation of steam-pretreated wheat straw (SPWS) combined with wheat-starch hydrolysate feed was performed in two separate processes. The average yield of ethanol and the xylose consumption reached 86% and 69%, respectively, when the hydrolysate of the enzymatically hydrolyzed (18.5% WIS) unwashed SPWS solid fraction and wheat-starch hydrolysate were fed to the fermentor after 1 h of fermentation of the SPWS liquid fraction. In the other configuration, fermentation of the SPWS hydrolysate (7.0% WIS), resulted in an average ethanol yield of 93% from fermentation based on glucose and xylose and complete xylose consumption when wheat-starch hydrolysate was included in the feed. Increased initial cell density in the fermentation (from 5 to 20 g/L) did not increase the ethanol yield, but improved and accelerated xylose consumption in both cases.

Conclusions

Higher ethanol yield has been achieved in co-fermentation of xylose and glucose in SPWS hydrolysate when wheat-starch hydrolysate was used as feed, then in co-fermentation of the liquid fraction of SPWS fed with the mixed hydrolysates. Integration of first-generation and second-generation processes also increases the ethanol concentration, resulting in a reduction in the cost of the distillation step, thus improving the process economics.     

Purification of bioethanol effluent in an UASB reactor system with simultaneous biogas formation

In this study, the prospect of using an Upflow Anaerobic Sludge Blanket (UASB) reactor for detoxification of process water derived from bioethanol production has been investigated. The bioethanol effluent (BEE) originated from wet oxidized wheat straw fermented by Saccharomyces cerevisiae and Thermoanaerobacter mathranii A3M4 to produce ethanol from glucose and xylose, respectively. In batch experiments the methane potential of BEE was determined to 529 mL-CH(4)/g-VS. In batch degradation experiments it was shown that the presence of BEE had a positive influence on the removal of the inhibitors 2-furoic acid, 4-hydroxyacetophenone, and acetovanillone as compared to conversion of the inhibitors as sole substrate in synthetic media. Furthermore, experiments were carried out treating BEE in a laboratory-scale UASB reactor. The results showed a Chemical Oxygen Demand (COD) removal of 80% (w/w) at an organic loading rate of 29 g-COD/(L. d). GC analysis of the lignocellulosic related potentially inhibitory compounds 2-furoic acid, vanillic acid, homovanillic acid, acetovanillone, syringic acid, acetosyringone, syringol, 4-hydroxybenzoic acid, and 4-hydroxybenzaldehyde showed that all of these compounds were removed from the BEE in the reactor. Implementation of a UASB purification step was found to be a promising approach to detoxify process water from bioethanol production allowing for recirculation of the process water and reduced production costs.     

Candida shehatae and Saccharomyces cerevisiae work synergistically to improve ethanol fermentation from sugarcane bagasse and rice straw hydrolysate in immobilized cell bioreactor

Sugarcane bagasse (SCB) and rice straw (RS), abundant lignocellulosic agro‐industrial residues in South‐East Asia, are potent feedstocks for bioethanol production as they contain significant amount of glucose and xylose monomers after fractionation and subsequent enzymatic hydrolysis. To simultaneously convert glucose and xylose to ethanol, it requires co‐cultivation of Saccharomyces cerevisiae and Candida shehatae which are hexose and pentose‐fermenting yeasts, respectively. Xylose‐fermenting strain grows slower than glucose‐fermenting one, therefore low efficiency of xylose‐to‐ethanol conversion was found. To enhance the efficiency of ethanol fermentation, the present work proposed to improve xylose assimilation by using co‐immobilization of two strains in a packed bed bioreactor and to increase oxygenation of the medium by applying a recycled batch system when the recycle stream was intervened by a mixing system in a naturally aerated vessel. Initially, conversion of glucose and xylose to ethanol using pure culture was investigated. Subsequently, influence of different immobilization techniques was investigated. Cells entrapment in Ca‐alginate beads provided considerably high ethanol yield over cells immobilized on delignified cellulose, and thus it was selected to use as inoculum in an immobilized cell bioreactor (ICB). The results showed that continuous ethanol production yielded 0.38 and 0.40 g/g corresponding to 74.5% and 78.4% theoretical yields from SCB and RS hydrolysate, respectively. However, recycled batch system produced significantly improved ethanol yield to 0.49 g/g and 0.50 g/g corresponding to 96.1% and 98.0% theoretical yields for SCB and RS hydrolysate, respectively. In this study, higher ethanol concentration and less unfermented sugar concentration was successfully achieved in the ICB with recycled batch system when using SCB and RS hydrolysate as the substrate.     

Feasibility of ethanol production from coffee husks

The objective of this work was to evaluate the feasibility of ethanol production by fermentation of coffee husks by Saccharomyces cerevisiae. Batch fermentation studies were performed employing whole and ground coffee husks, and aqueous extract from ground coffee husks. It was observed that fermentation yield decreased with an increase in yeast concentration. The best results were obtained for the following conditions: whole coffee husks, 3 g yeast/l substrate, temperature of 30°C. Under these conditions ethanol production was 8.49 ± 0.29 g/100 g dry basis (13.6 ± 0.5 g ethanol/l), a satisfactory value in comparison to literature data for other residues such as corn stalks, barley straw and hydrolyzed wheat stillage (5–11 g ethanol/l). Such results indicate that coffee husks present excellent potential for residue-based ethanol production.