Fabrication of gelatin/calcium phosphate composite nanofibrous membranes by biomimetic mineralization

Based on the principles of biomimetic mineralization, biocomposite nanofibrous membranes were fabricated by the growth of CaP crystals on electrospun gelatin nanofibers to mimic both the physical architecture and chemical composition of natural bone ECM. Plenty more CaP crystals formed on the nanofibrous membrane containing Ca(2+) ion precursors, in which these crystals were also observed on the inner side of membrane. The release rate of Ca(2+) ion precursors from the nanofibrous membrane was slower than that of PO(4)(3-) ion precursors, suggesting the existence of more strong intermolecular interaction between gelatin and Ca(2+) ions. ATR-FTIR and XRD results clearly revealed the formation of CaP crystals mixed with apatite and CaCO(3), or apatite and TCP on the membranes. The Ca/P molar ratio of crystals obtained from the XPS data was 2.03 and 1.60, which depended on the mineralization conditions. Higher amount of CaP crystals significantly accelerated the deposit rate of bone-like apatite on the surface of composite membrane, meaning to the improved in vivo bone bioactivity.     

Core‐shell nanofibers: Integrating the bioactivity of gelatin and the mechanical property of polyvinyl alcohol

Coaxial electrospinning is used to fabricate nanofibers with gelatin in the shell and polyvinyl alcohol (PVA) in the core in order to derive mechanical strength from PVA and bioactivity from gelatin. At a 1:1 PVA/gelatin mass ratio, the core‐shell nanofiber scaffolds display a Young's modulus of 168.6 ± 36.5 MPa and a tensile strength of 5.42 ± 1.95 MPa, which are significantly higher than those of the scaffolds composed solely of gelatin or PVA. The Young's modulus and tensile strength of the core‐shell nanofibers are further improved by reducing the PVA/gelatin mass ratio from 1:1 to 1:3. The mechanical analysis of the core‐shell nanofibers suggests that the presence of the gelatin shell may improve the molecular alignment of the PVA core, transforming the semi‐crystalline, plastic PVA into a more crystallized, elastic PVA, and enhancing the mechanical properties of the core. Lastly, the PVA/gelatin core‐shell nanofibers possess cellular viability, proliferation, and adhesion similar to these of the gelatin nanofibers, and show significantly higher proliferation and adhesion than the PVA nanofibers. Taken together, the coaxial electrospinning of nanofibers with a core‐shell structure permits integration of the bioactivity of gelatin and the mechanical strength of PVA in single fibers. © 2013 Wiley Periodicals, Inc. Biopolymers 101: 336–346, 2014.     

Fabrication of agar-gelatin hybrid scaffolds using a novel entrapment method for in vitro tissue engineering applications

Scaffolds of agar and gelatin were developed using a novel entrapment method where agar and gelatin molecules mutually entrapped one another forming stable cell adhesive matrices. Glutaraldehyde was used as a crosslinking agent for gelatin. Three types of hybrid matrices were prepared using agar and gelatin in different proportions in the weight ratio of 1:1, 2:1, and 3:1. Surface characterization of dry scaffolds was carried out by scanning electron microscope. Swelling studies were carried out in phosphate buffer saline (PBS) at physiological pH 7.4. The integral stability of the scaffolds was evaluated by estimating the released disintegrated gelatin from them in PBS at pH 7.4. The attachment kinetics of the cells was evaluated by culturing mouse fibroblast cell line NIH 3T3 on films. The cytocompatibility of these matrices was determined by studying growth kinetics of NIH 3T3 cells on them and morphology of cells was observed through optical photographs taken at various days of culture. It was found that the matrices containing agar and gelatin in 2:1 weight ratio exhibited best growth kinetics. The results obtained from these studies have suggested that the above-described method is a cheap and easy way to fabricate agar-gelatin hybrid scaffolds to grow cells which can be used in various in vitro tissue engineering applications like screening of drugs.     

Fundamental considerations in the effect of molecular weight on the glass transition of the gelatin/cosolute system

Four molecular fractions of gelatin produced by alkaline hydrolysis of collagen were investigated in the presence of cosolute to record the mechanical properties of the glass transition in high-solid preparations. Dynamic oscillatory and stress relaxation moduli in shear were recorded from 40°C to temperatures as low as -60°C. The small-deformation behavior of these linear polymers was separated by the method of reduced variables into a basic function of time alone and a basic function of temperature alone. The former allowed the reduction of isothermal runs into a master curve covering 17 orders of magnitude in the time domain. The latter follows the passage from the rubbery plateau through the glass transition region to the glassy state seen in the variation of shift factor, a(T) , as a function of temperature. The mechanical glass transition temperature (T(g) ) is pinpointed at the operational threshold of the free volume theory and the predictions of the reaction rate theory. Additional insights into molecular dynamics are obtained via the coupling model of cooperativity, which introduces the concept of coupling constant or interaction strength of local segmental motions that govern structural relaxation at the vicinity of T(g) . The molecular weight of the four gelatin fractions appears to have a profound effect on the transition temperature or coupling constant of vitrified matrices, as does the protein chemistry in relation to that of amorphous synthetic polymers or gelling polysaccharides.     

明胶/海藻酸钠/沙蒿胶复合水凝胶的制备及表征

为探究明胶（G）、海藻酸钠（SA）,沙蒿胶（ASKG）对复合水凝胶的力学性能、溶胀和保湿性能的影响,采用共混-离子交联法制备海藻酸钠/明胶/沙蒿胶复合水凝胶,并对制得的水凝胶进行结构表征和溶血率测试。结果表明:当G质量分数为2.5%,SA为1.5%,ASKG为0.7%时,复合水凝胶压缩强度达到427.2 kPa,拉伸强度达到563.449 kPa,断裂伸长率为117%,溶胀率为744%,且具有较好的保湿性能。红外光谱表明,由于沙蒿胶中存在大量羟基,因此加入沙蒿胶后在3 300 cm^-1～3 600 cm^-1羟基峰形变宽。G/SA/ASKG复合水凝胶溶血率低于5%,具有较好的网络孔结构和血液相容性,为复合水凝胶在医用敷料方面的应用提供一定的参考价值。     

Preparation of gelatin microbeads with a narrow size distribution using microchannel emulsification

The purpose of this study was to prepare monodisperse gelatin microcapsules containing an active agent using microchannel (MC) emulsification, a novel technique for preparing water-in-oil (W/O) and oil-in-water (O/W) emulsions. As the first step in applying MC emulsification to the preparation of monodisperse gelatin microcapsules, simple gelatin microbeads were prepared using this technique. A W/O emulsion with a narrow size distribution containing gelatin in the aqueous phase was created as follows. First, the aqueous disperse phase was fed into the continuous phase through the MCs at 40°C (operating pressure: 3.9 kPa). The emulsion droplets had an average particle diameter of 40.7 μm and a relative standard deviation of 5.1%. The temperature of the collected emulsion was reduced and maintained at 25°C overnight. The gelatin microbeads had a smooth surface after overnight gelation; the average particle diameter was calculated to be 31.6 μm, and the relative standard deviation, 7.3%. The temperature was then lowered to 5°C by rapid air cooling and finally dried. The gelatin beads were dried and could be resuspended well in iso-octane. The had an average particle diameter of 15.6 μm, and a relative standard deviation of 5.9%. Using MC emulsification, we were able to prepare gelatin microbeads with a narrow size distribution. Since this emulsification technique requires only a low-energy input, it may create desirable experimental conditions for microencapsulation of unstable substances such as peptides and proteins. This method is promising for making monodisperse microbeads.     

Fabrication of porous polycaprolactone/hydroxyapatite (PCL/HA) blend scaffolds using a 3D plotting system for bone tissue engineering

For tissue engineering and regeneration, a porous scaffold with interconnected networks is needed to guide cell attachment and growth/ingrowth in three-dimensional (3D) structure. Using a rapid prototyping (RP) technique, we designed and fabricated 3D plotting system and three types of scaffolds: those from polycaprolactone (PCL), those from PCL and hydroxyapatite (HA), and those from PCL/HA and with a shifted pattern structure (PCL/HA/SP scaffold). Shifted pattern structure was fabricated to increase the cell attachment/adhesion. The PCL/HA/SP scaffold had a lower compressive modulus than PCL and PCL/HA scaffold. However, it has a better cell attachment than the scaffolds without a shifted pattern. MTT assay and alkaline phosphatase activity results for the PCL/HA/SP scaffolds were significantly enhanced compared to the results for the PCL and PCL/HA scaffolds. According to their degree of cell proliferation/differentiation, the scaffolds were in the following order: PCL/HA/SP > PCL/HA > PCL. These 3D scaffolds will be applicable for tissue engineering based on unique plotting system.     

Production of a non‐triple helical collagen α chain in transgenic silkworms and its evaluation as a gelatin substitute for cell culture

We generated transgenic silkworms that synthesized human type I collagen α1 chain [α1(I) chain] in the middle silk glands and secreted it into cocoons. The initial content of the recombinant α1(I) chain in the cocoons of the transgenic silkworms was 0.8%. The IE1 gene, a trans‐activator from the baculovirus, was introduced into the transgenic silkworm to increase the content of the chain. We also generated silkworms homozygous for the transgenes. These manipulations increased the α1(I) chain content to 8.0% (4.24 mg per cocoon). The α1(I) chain was extracted and purified from the cocoons using a very simple method. The α1(I) chain contained no hydroxyprolines due to the absence of prolyl‐hydroxylase activity in the silk glands. Circular dichroism analysis showed that the secondary structure of the α1(I) chain is similar to that of denatured type I collagen, demonstrating the absence of the triple helical structure. Human skin fibroblasts were seeded on the α1(I) chain‐coated dishes. The cells attached and spread, although at decreased chain concentrations the spreading rate was lower than that of the collagen and gelatin. Cynomolgus monkey embryonic stem cells cultured on the α1(I) chain‐coated dishes maintained an undifferentiated state after 30 passages, and their pluripotency was confirmed by teratoma formation in severe combined immunodeficient mice. These results show that the recombinant human α1(I) chain is a promising candidate biomaterial as a high‐quality and safe gelatin substitute for cell culture. Biotechnol. Bioeng. 2010;106: 860–870. © 2010 Wiley Periodicals, Inc.     

Viscosity-temperature behavior of chitin solutions using lithium chloride/DMA as solvent

Solutions of chitin in Li⁺/N,N-dimethylacetamide systems were studied via viscometry, using LiCl concentrations of 3% and 5% (m/v) and chitin concentrations ranging from 0.075 to 0.375 g L⁻¹. The reduced viscosity number versus concentration plot showed a minimum that was related to the formation of Li⁺–OC complex moieties along chitin macromolecular chains. Viscosity behavior was affected by temperature according to the Eyring model: concentration dependence of flow enthalpy of activation was correlated to polymer–polymer interactions and flow entropy of activation to the stiffness of the complexed chitosan macromolecular chain.     

A study of acid phosphatase in mouse kidney using naphthol AS/BI phosphate as a substrate

Summary A kinetic study of mouse kidney acid phosphatase has been performed using an application of the histochemical method ofBurstone (1958a, b). The suitability of the use of naphthol AS/BI phosphate as a substrate for biochemical assays of acid phosphatase has been ascertained. However, the rate of inhibition of the enzyme by sodium molybdate and sodium fluoride suggests that naphthol AS/BI phosphate may represent a substrate for an acid phosphatase different from-glycerophosphatase.     

Fabrication of a biomimetic spinal cord tissue construct with heterogenous mechanical properties using intrascaffold cell assembly

In tissue engineering studies, scaffolds play a very important role in offering both physical and chemical cues for cell growth and tissue regeneration. However, in some cases, tissue regeneration requires scaffolds with high mechanical properties (e.g., bone and cartilage), while cells need a soft mechanical microenvironment. In this study, to mimic the heterogenous mechanical properties of a spinal cord tissue, a biomimetic rat tissue construct is fabricated. A collagen-coated poly(lactic-co-glycolic acid) scaffold is manufactured using thermally induced phase separation casting. Primary rat neural cells (P01 Wistar rat cortex) with soft hydrogels are later printed within the scaffold using an image-guided intrascaffold cell assembly technique. The scaffolds have unidirectional microporous structure with parallel axial macrochannels (260 ± 4 µm in diameter). Scaffolds showed mechanical properties similar to rat spine (ultimate tensile strength: 0.085 MPa, Young's modulus [stretch]: 0.31 MPa). The bioink composed of gelatin/alginate/fibrinogen is precisely printed into the macrochannels and showed mechanical properties suitable for neural cells (Young's modulus [compressive]: 3.814 kPa). Scaffold interface, cell viability, and immunostaining analyses show uniform distribution of stable, healthy, and elongated neural cells and neurites over 14 culture days in vitro. The results demonstrated that this method can serve as a valuable tool to aid manufacturing of tissue constructs requiring heterogenous mechanical properties for complex cell and/or biomolecule assembly.     

Liposome formulation of NSC-639829 using halothane as a solvent: A technical note

Conclusion  Halothane has been successfully used as a solvent for the liposome formulation of NSC-639829. Liposomes with similar morphology, particle size, incorporation efficiency, and stability were obtained with halothane, chloroform, and ether. Halothane provides additional ease in formulation because of its higher volatility and safety as compared with chloroform and ether. Halothane can be regarded as a safe alternative to chloroform or ether in liposome formulation.     

Overproduction of laccase by a monokaryotic strain of Pycnoporus cinnabarinus using ethanol as inducer

AIMS: Laccase production by the monokaryotic strain Pycnoporus cinnabarinus ss3 was studied using ethanol as inducer in the culture medium. METHODS AND RESULTS: The effect of ethanol was tested at 10, 20, 30, 35 and 45 g l-1 and compared with that of ferulic acid, known until now as the most efficient inducer for laccase expression by P. cinnabarinus ss3. In the presence of 35 g l-1 ethanol, laccase activity (266 600 U l-1) and productivity (19 000 U l-1 day-1) were nine and fivefold higher compared with ferulic acid-induced cultures, and 155- and 65-fold higher compared with non-induced cultures, respectively. In vivo, ethanol added to the culture medium of P. cinnabarinus ss3 favoured a continuous and high expression of laccase gene. Under these conditions, P. cinnabarinus ss3 produced preferentially the isoenzyme LAC I. Ethanol added in vitro to the purified P. cinnabarinus ss3 laccase typically inhibited the enzymatic activity. CONCLUSIONS: In spite of an initial inhibitory effect on mycelial growth, ethanol was shown to be a very strong inducer for laccase expression by P. cinnabarinus ss3 allowing an average yield of 1-1.5 g l-1 laccase. SIGNIFICANCE AND IMPACT OF THE STUDY: This study identified P. cinnabarinus ss3 as an outstanding producer of laccase in the presence of ethanol as inducer. Ethanol is an inexpensive agricultural by-product and the process is simple to scale-up for industrial production.     

In vitro study of using calcium phosphate cement as immunoisolative device to enclose insulinoma/agarose microspheres as bioartificial pancreas

In this study, the feasibility of using calcium phosphate cement (CPC) as immunoisolative device to enclose insulinoma/agarose microspheres as bioartificial pancreas was evaluated. We fabricated a chamber by CPC and utilized X-ray diffraction, Scanning electron microscope and Mercury intrusion porosimetry to identify the characters of the CPC chamber. The nominal molecular weight cut-off and cytotoxicity of CPC chamber were also evaluated. An insulinoma cell line (RIN-m5F) was chosen as insulin source and encapsulated in agarose microspheres and then enclosed in preformed CPC chamber. Insulin secretion was analyzed by Enzyme-linked immunosorbant assay to evaluate the function of insulinoma enclosed in CPC chamber. Results showed that the CPC chamber was non-cytotoxicity to insulinoma and can block the penetration of molecules which molecular weight larger than 12.4 kDa. Insulinoma inside the CPC chamber can secrete insulin in stable level for 30 days. This study indicated that we may use CPC as immunoisolative material to enclose insulinoma/agarose microspheres as bioartificial pancreas.     

Techno-economic comparison of a biological hydrogen process and a 2nd generation ethanol process using barley straw as feedstock

A process combining dark fermentation and photofermentation for production of hydrogen is interesting due to its potential of producing hydrogen at a high yields. In this study, the hydrogen process is compared to a 2nd generation ethanol process with respect to cost and with the aim of increasing our understanding of the pros and cons and giving a clear picture of the present status of the two processes. The hydrogen production cost was found to be about 20 times higher than the ethanol production cost, 421.7 €/GJ compared to 19.5 €/GJ. The main drawbacks of the hydrogen process are its low productivity, low energy efficiency, and the high cost of buffer and base required to control the pH.