Advances in the fracture mechanics of cortical bone

As cortical bone is a semi-brittle solid, its fracture is dependent not only on the magnitude of the applied stress, but also on the nature of any intrinsic or introduced cracks. Consequently a variety of fracture mechanics techniques have been utilised to evaluate the fracture toughness of cortical bone, including the single edge notched, centre notched cylindrical and compact tension methods, and values have been established for the critical stress intensity factor (Kc) and the critical strain energy release rate (Gc). The Kc and Gc values obtained depend on the orientation of the cortical bone, as well as on bone density, the velocity of crack propagation and specimen geometry. The significance of these fracture mechanics parameters for cortical bone is critically reviewed.     

Variability of ecdysteroid-induced cell cycle alterations in Drosophila Kc sublines

Abstract. The cell cycle of two lines isolated from Drosophila Kc cells was followed by flow cytofluorometry and cell counting. The first line is the 8-9K clone which grew in a medium supplemented with 5% serum; the second, named subline Kc0, grew in a serum-free medium. The stationary phase is characterized by a G₂ cell accumulation: 73% in the 8-9K clone and 50% in the Kc0 subline.
When the medium was supplemented with the steroid moulting hormone 20-hydroxyecdysone, more than 90% of 8-9K cells and 65% of Kc0 cells were progressively arrested in G₂. In the continuous presence of 20-hydroxyecdysone, most of the 8-9K cells remain G₂-arrested; no massive G₂ release into M was observed and only a few cells were able to divide. When treated for only 3 or 7 days, a transient release into M and proliferation occurred after hormone-free medium renewal, largely masked by G₂ cell death. These results are discussed in comparison with other reports on cell cycle alteration induced by ecdysteroids.     

Human bone marrow CFU-GM and BFU-E localized by light scatter cell sorting

Flow cytometric separation was performed on the normal human bone marrow (BM) by using the low-angle (0 degrees) or high-angle (90 degrees) light scatter. Four distinct subpopulations of cells can be enriched from normal human BM and these fractions were subsequently evaluated for their morphological properties as well as their clonogenic capacity in various progenitor cell assays. Our results indicate that human erythroid and granulocyte-macrophage progenitor cells can be separated from BM low-density cells by cell sorting, and these cells show similar 0 degrees and 90 degrees light scatter properties to those observed with murine bone marrow studies. Flow cytometric analysis also suggests that the majority of sorted BFU-E and CFU-GM resides in the blast cell subset of human BM mononuclear cells.     

Fracture toughness and work of fracture of hydrated, dehydrated, and ashed bovine bone

Bone, a tri-phase composite, consists of nano-sized apatite minerals, an organic component, and water. Heat-treated bovine cortical bone has been proposed as a candidate for void-filling bone substitute. However, the toughness of heat-treated bone is not yet fully studied. Fracture toughness (K(c)) and work of fracture (W(f)) of hydrated, dehydrated, and ashed bovine bone were estimated using a single-edge V-notched beam method. Thermal gravimetric analysis and differential thermal analysis were used to determine the temperature at which the organics and water were removed. Dehydrated specimens were obtained by placing the samples in a 60 degrees C vacuum oven for 24h or a 110 degrees C furnace for 2h. Ashed specimens were obtained by heat-treating samples at 600 degrees C for 24h. K(c) of bovine specimens decreased from 5.5MPa.m(1/2) for hydrated bone, to 3.8MPa.m(1/2) for dehydrated specimens, and to 0.36MPa.m(1/2) for ashed specimens. W(f) decreased from 7.1 to 1.1kJ/m(2) for dehydrated specimens, and to 0.04kJ/m(2) for ashed specimens. The main reasons for the significant decreases in K(c) and W(f) may be attributed to water's ability in stabilizing collagen structure and to the organics' ability in making bone more ductile. Because of the large decrease in fracture toughness and work of fracture, we suggest that ashed bone is not appropriate for load-bearing bone substitute in areas where bone experiences loadings in flexure.     

Effect of temperature on the fracture toughness of compact bone

Bone is a composite composed mainly of organics, minerals, and water. Many researchers have studied effects such as crack velocity, density, orientation, storage media, porosity, and age on the fracture toughness (K(C), also called critical stress intensity factor) of compact bone. Most of these studies were conducted at room temperature. Considering that the body temperature of animals is greater than room temperature, and that bone has a large volumetric percentage of organics and water (generally, 55-65%), it is hypothesized that temperature has a significant effect on the fracture toughness of compact bone. Single-edge V-notched (SEVN) specimens were prepared to measure the fracture toughness of bovine femur and manatee rib in water at 0, 10, 23, 37, and 50 degrees C in four-point flexure. The fracture toughness values of bovine femur and manatee rib were found to decrease from 7.0 to 4.3MPam(1/2) and from 5.5 to 4.0MPam(1/2), respectively, as temperature increased over a temperature range of 50 degrees C. The results support the hypothesis that temperature has a significant effect on the fracture toughness of compact bone. Therefore, we suggest that study on fracture toughness of bone should be done at physiologically relevant temperatures.     

Evaluation of fracture toughness of human dentin using elastic-plastic fracture mechanics

Dentin, the mineralized tissue forming the bulk of the tooth, lies between the enamel and the pulp chamber. It is a rich source of inspiration for designing novel synthetic materials due to its unique microstructure. Most of the previous studies investigating the fracture toughness of dentin have used linear-elastic fracture mechanics (LEFM) that ignores plastic deformation and could underestimate the toughness of dentin. With the presence of collagen (approximately 30% by volume) aiding the toughening mechanisms in dentin, we hypothesize that there is a significant difference between the fracture toughness estimated using LEFM (Kc) and elastic-plastic fracture mechanics (EPFM) (KJc). Single-edge notched beam specimens with in-plane (n=10) and anti-plane (n=10) parallel fractures were prepared following ASTM standard E1820 and tested in three-point flexure. KJc of the in-plane parallel and anti-plane parallel specimens were found to be 3.1 and 3.4 MPa m 1/2 and Kc were 2.4 and 2.5 MPa m 1/2, respectively. The fracture toughness estimated based on KJc is significantly greater than that estimated based on Kc (32.5% on average; p<0.001). In addition, KJc of anti-plane parallel specimens is significantly greater than that of in-plane parallel specimens. We suggest that, in order to critically evaluate the fracture toughness of human dentin, EPFM should be employed.     

Extrachromosomal circular DNAs in Drosophila melanogaster: Comparison between embryos and Kc0% cells

We established the size distribution of extrachromosomal covalently closed circular DNA molecules from embryos of various Drosophila melanogaster strains and from Kc0% tissue culture cells. In embryos, more than 80% of the circular DNA molecules are smaller than 2.5 kb and all the distributions show a peak of molecules of between 200 and 400 bp. The Kc0% cell distribution differs mainly from that of embryos in that 48% of the molecules have a size between 4 and 8 kb. Correlating with this, circular molecules homologous to copia, 412 and 297 were detected only in Kc0% cells. The three tandemly repeated families containing the 5S genes, the histone genes and the 240 bp repeat of the ribosomal DNA intergenic spacer, which had previously been identified in circular DNAs from embryos, were also found in cultured cells. A fourth tandemly repeated family corresponding to the 1.688 g/cm³ satellite DNA was detected, both in embryos and Kc0% cells. It consists of circular multimeric molecules containing multiple copies of the 359 bp repeated unit. No circular DNA molecules homologous to the actin genes, the type I ribosomal DNA insertion, or the F and I transposable elements were found in embryos or Kc0% cells. Thus it appears that the extrachromosomal circular DNA molecules from embryos and from tissue culture cells differ mainly in the presence of circular copies of the copia-like transposable elements.     

Determination of second virial coefficient of proteins using a dual-detector cell for simultaneous measurement of scattered light intensity and concentration in SEC-HPLC

A method is proposed for the measurement of the B22 value of proteins in aqueous solutions in flow-mode that utilizes a novel fabricated dual-detector cell, which simultaneously measures protein concentration and the corresponding scattered light intensity at 90 degrees , after the protein elutes from a size-exclusion column. Each data point on the chromatograms obtained from the light scattering detector and the concentration (ultraviolet) detector is converted to Rayleigh's ratio, Rtheta, and concentration, c, respectively. The B22 value is calculated from the slope of the Debye plot (Kc/Rtheta versus c) generated from a range of concentrations obtained from these chromatograms for a single protein injection. It is shown that this method provides reliable determination of the B22 values for such proteins as lysozyme, chymotrypsinogen, and chymotrypsin in various solution conditions that agree well with those reported in literature.     

A meta-analysis of cigarette smoking,bone mineral density and risk of hip fracture: recognition of a major effect.

OBJECTIVE: To determine the magnitude and importance of the relation between smoking, bone mineral density, and risk of hip fracture according to age. DESIGN: Meta-analysis of 29 published cross sectional studies reporting the difference in bone density in 2156 smokers and 9705 non-smokers according to age, and of 19 cohort and case-control studies recording 3889 hip fractures reporting risk in smokers relative to non-smokers. RESULTS: In premenopausal women bone density was similar in smokers and non-smokers. Postmenopausal bone loss was greater in current smokers than non-smokers, bone density diminishing by about an additional 2% for every 10 year increase in age, with a difference of 6% at age 80. In current smokers relative to non-smokers the risk of hip fracture was similar at age 50 but greater thereafter by an estimated 17% at age 60, 41% at 70, 71% at 80, and 108% at 90. These estimates of relative risk by age, derived directly from a regression analysis of the studies of smoking and hip fracture, were close to estimates using the difference in bone density between smokers and non-smokers and the association between bone density and risk of hip fracture. The estimated cumulative risk of hip fracture in women in England was 19% in smokers and 12% in non-smokers to age 85; 37% and 22% to age 90. Among all women, one hip fracture in eight is attributable to smoking. Limited data in men suggest a similar proportionate effect of smoking as in women. The association was not explained by smokers being thinner, younger at menopause, and exercising less nor by actions of smoking on oestrogen, but smoking may have a direct action on bone. CONCLUSIONS: Hip fracture in old age is a major adverse effect of smoking after the menopause. The cumulative excess bone loss over decades is substantial, increasing the lifetime risk of hip fracture by about half.     

The effect of moisture absorption on the fatigue crack propagation resistance of acrylic bone cement.

In vivo, bone cement is subject to cyclic loading in a fluid environment. However, little is known about the effect of moisture absorption on the fatigue crack propagation resistance of bone cement. The effect of moisture absorption at 37 degrees C on the fatigue crack propagation resistance of a common bone cement (Endurance, DePuy, Orthopaedics, Inc.) was examined. Preliminary fracture toughness tests were conducted on disk-shaped, vacuum-mixed cement specimens (compact tension type) that were cyclically pre-cracked. Plain-strain fracture toughness K(IC) (MPa square root(m)) was determined. To study the effect of moisture absorption four treatment groups, with different soaking periods in Ringer's at 37 degrees C, of Endurance cement were tested. The specimens weights prior to and following soaking showed a significant increase in mean weight for specimens soaked for 8 and 12 weeks. Linear regression analysis of log(da/dN) vs. log (deltaK) was conducted on the combined data in each fatigue test group. Soaking bone cement in Ringer's at 37 degrees C for 8 and 12 weeks lead to an improvement in fatigue crack propagation resistance, that may be related to water sorption that increases polymer chain mobility, with enhanced crack tip blunting. It may be more physiologically relevant to conduct in vitro studies of fatigue and fracture toughness of bone cements following storage in a fluid environment.     

北方稻田蒸散需水分析及其作物系数确定

利用Penman-Monteith方程估算了中国北方下辽河平原地区52年(1951～2002)的潜在蒸散量,分析了潜在蒸散的年际动态变化规律;在中国科学院沈阳生态实验站的水田实验地上,利用非称重式蒸渗仪对充分供水条件下同一水稻品种稻田蒸散量进行了测定,在此基础上确定了水稻作物系数.结果表明,在北方下辽河平原地区稻田蒸散量变化在581～695 mm之间,年际变率为24%.无论是湿润年还是干旱年,由于受降雨量及其时间分配不均的影响,在该地区水稻生产中都需要有灌溉水补充.整个生育期水稻作物系数多年(1993～2002)平均值为1.32,水稻生育期内作物系数基本符合二次曲线趋势变化.     

Hyperbaric Hyperoxia Accelerates Fracture Healing in Mice

Increased oxygen tension influences bone metabolism. This study comprised two main experiments: one aimed to determine the bone mineral apposition and bone formation rates in vivo under hyperbaric hyperoxia (HBO), and the other aimed to evaluate the effects of exposure to HBO on fracture healing. In experiment 1, male mice were exposed to HBO [90 min/day at 90% O₂ at 2 atmospheres absolute (ATA) for 5 days]. In experiment 2, an open femur fracture model was created in mice, followed by exposure to HBO 5 times/week (90 min/day at 90% O₂ at 2 ATA) for 6 weeks after surgery. In experiment 1, HBO treatment significantly increased the mineral apposition and bone formation rates in the lumbar vertebra and femur and type 1 collagen alpha 1 and alkaline phosphatase mRNA expression in the lumbar vertebra. In experiment 2, at 2 weeks after fracture, the fracture callus was significantly larger in the HBO group than in the non-HBO group. Furthermore, at 4 and 6 weeks after fracture, radiographic findings showed accelerated fracture healing in the HBO group. At 6 weeks after fracture, femur stiffness and maximum load were significantly higher in the HBO group than in the non-HBO group. Urinary 8-hydroxy-2′-deoxyguanosine and plasma calcium concentrations were not significantly different between groups. These results suggest that exposure to HBO enhances bone anabolism and accelerates fracture healing without causing oxidative DNA damage or disruption of plasma calcium homeostasis.     

Enhancement of recombinant human EPO production and glycosylation in serum-free suspension culture of CHO cells through expression and supplementation of 30Kc19

We previously reported that the expression of Bombyx mori 30Kc19 gene in CHO cells significantly improved both the production and sialylation of recombinant human EPO (rHuEPO) in adhesion culture mode. In this study, the effects of 30Kc19 expression and supplementation of 30Kc19 recombinant protein on the productivity and glycosylation pattern of rHuEPO were investigated in the serum-free suspension culture mode. Especially, glycosylation pattern was examined in detail using a quantitative MALDI-TOF MS method. The expression of 30Kc19 increased the EPO production by 2.5-folds and the host cells produced rHuEPO with more complex glycan structures and a larger content of sialic acid and fucose. The glycan structures of rHuEPO in the 30Kc19-expressing cell consisted of bi-, tri-, tetra-, and penta-antennary branching (35, 18, 33, and 14?%, respectively), while the control cells produced predominantly bi-antennary branching (70?%). About 53?% of the glycans from rHuEPO in the 30Kc19-expressing cell was terminally sialylated, while no obvious sialylated glycan was found in the control cells. The percentage of fucosylated glycans from the 30Kc19-expressing cell culture was 77?%, whereas only 61?% of the glycans from the control cell were fucosylated glycans. We also examined whether these effects were observed when the recombinant 30Kc19 protein produced from Escherichia coli was supplemented into the culture medium for CHO cells. In the control cell line without the 30Kc19 gene, EPO production increased by 41.6?% after the addition of 0.2?mg/mL of the recombinant 30Kc19 protein to the culture medium. By the Western blot analysis after two-dimensional electrophoresis (2-DE) of isoforms of EPO, we confirmed that 30Kc19 enhanced the sialylation of EPO glycans. These results demonstrated that both 30Kc19 gene expression and the recombinant 30Kc19 protein addition enhanced rHuEPO productivity and glycosylation in suspension culture. In conclusion, the utilization of 30Kc19 in CHO cell culture holds great promise for use in the manufacturing of improved biopharmaceutical glycoproteins.     

Stabilization of enzymes by the recombinant 30Kc19 protein

In previous studies, we reported that the 30K protein originating from the silkworm inhibited apoptosis in mammalian cells. In this work, we demonstrated that the 30Kc19 protein, which is most abundant 30K protein in silkworm hemolymph, also enhanced enzyme stability. When the recombinant 30Kc19 protein was supplemented into distilled-deionized water containing alkaline phosphatase or horseradish peroxidase, deactivation of both enzymes induced by non-buffered DDW was significantly suppressed. The increase in enzyme stability due to the presence of 30Kc19 was similar to that observed for bovine serum albumin, which is commonly used in conventional enzyme reactions. The decrease in enzyme activity due to long-term storage in different buffer systems was also inhibited by 30Kc19. The 30Kc19 protein structure was shown to play a vital role in stabilizing the enzyme. These results imply that the recombinant 30Kc19 protein hold promise for use as an additive to increase or maintain enzyme activity.     

Expression of Bombyx mori 30Kc19 protein in Escherichia coli and its anti-apoptotic effect in Sf9 cell

The silkworm hemolymph has an anti-apoptotic activity in insect, mammalian, and human cell systems. The protein from silkworm hemolymph with the highest apoptosis inhibiting activity was found to be 30Kc19 protein, which was one of the ‘30K proteins’. In this study, 30Kc19 protein encoded by the 30Kc19 gene of the silkworm was expressed in Escherichia coli with (pET-22b(+)) and without (pET-3a) pelB leader sequence. 30Kc19 protein was over-expressed largely as a soluble form by pET-3a and both as soluble and insoluble forms by pET-22b(+). The medium was supplemented with each of the recombinant 30Kc19 proteins, and their presence was found to inhibit nuclear fragmentation and apoptotic body formation in actinomycin D-induced Sf9 cell apoptosis. Moreover, 30Kc19 protein repressed the activation of Sf-caspase-1. The 30Kc19 protein obtained from periplasm showed the most effective anti-apoptotic activity. This protein holds great potential for industrial and pharmaceutical applications since mass production and easy purification of this protein is possible.     

Enhancement of recombinant human EPO production and sialylation in chinese hamster ovary cells through Bombyx mori 30Kc19 gene expression

Productivity and sialylation are two important factors for the production of recombinant glycoproteins in mammalian cell culture. In our previous study, we found that silkworm hemolymph increased the sialylation of recombinant secreted human placental alkaline phosphatase in the insect cells, promoted the transfer of sialic acids onto the glycoprotein oligosaccharides in an in vitro asialofetuin sialylation system, and enhanced recombinant protein production in the Chinese hamster ovary (CHO) cells. These beneficial effects were mainly due to the 30K proteins, which consist of five isoforms. Among the 30K proteins, 30Kc19 was determined to be the major component. In this study, the 30Kc19 gene was introduced into a CHO cell line producing recombinant human erythropoietin, and its effects on productivity and sialylation were investigated. The transient expression of 30Kc19 significantly improved the production and sialylation of EPO. A stable cell line containing 30Kc19 was also established to investigate the effect of 30Kc19 gene expression. The stable expression of 30Kc19 increased the production and sialylation by 102.6% and 87.1%, respectively. The enhanced productivity from 30Kc19 expression is believed to occur because the 30Kc19 protein suppresses the loss of mitochondrial membrane potential and consequently improves the generation of intracellular ATP. In addition, the positive effect of 30Kc19 expression on sialylation is believed to be due to its ability to maintain sialyltransferase activity. In conclusion, 30Kc19 expression is a novel approach to improve the production and sialylation of recombinant glycoproteins in CHO cells.     

The healing of facial bone fractures by the process of secondary union

The mechanism of healing of facial bone fractures was investigated in a rabbit model. Twelve New Zealand white rabbits underwent surgically induced fractures of the right infraorbital rim and fracture ostectomies (4 to 5 mm) of the left infraorbital rim. Animals were sacrificed 2, 4, and 8 weeks postfracture. Bone, including periosteum, obtained from each fracture or fracture osteoctomy site was divided longitudinally for hematoxylin and eosin staining, fluorescent microscopy, microangiography, and microradiography. Sequential fluorochrome labels of oxytetracycline (30 mg/kg), alizarin complexone (30 mg/kg), DCAF (20 mg/kg), and xylenol orange (90 mg/kg) were administered 24 hours preoperatively and at 1, 2, 4, and 8 weeks postfracture. All fracture and fracture ostectomy sites demonstrated vascular ingrowth, mineralization, and woven bone formation by 2 to 4 weeks postoperatively, beginning with a cartilage precursor. Subsequently, the woven bone was replaced with remodeled lamellar bone, resulting in complete bony healing by 8 weeks postoperatively. These steps were substantiated by microscopic, microradiographic, and radiologic examination of the specimens. This study demonstrates that fractures of the facial bones in a rabbit model heal by a process of new bone formation that resembles secondary union in endochondral bones.     

In vivo phosphorylation of Drosophila melanogaster nuclear lamins during both interphase and mitosis

To study phosphorylation of D. melanogaster nuclear lamins in vivo, we used Kc tissue culture cells. Kc cells contain products of both lamin genes, the lamin Dm0 gene encoding constitutive polypeptides expressed in almost all cell types and the developmentally regulated lamin C gene. We grew Kc cells in low phosphate medium and labelled them with (32P(H3PO4. To obtain mitotic cells we used vinblastine to arrest cells in metaphase. Cells were collected, washed, lysed and resultant extracts fractionated in the presence of protein phosphatase inhibitors. D. melanogaster proteins were then denatured by boiling in SDS plus DTT, followed by immunoaffinity chromatography and SDS-PAGE purification. As anticipated, we found that a CNBr fragment derived from the N-terminal part of lamin Dm0-derivatives (amino acid residues 2-158; fragment A) was phosphorylated during both interphase and mitosis. Interphase but not mitotic phosphorylation was found on an internal CNBr fragment (derived from the end of the central rod domain and the first part of the C-terminal lamin tail; amino acid residues 385-548; fragment D). Interphase only phosphorylation was also detected on another CNBr fragment derived from the extreme C-terminal portion of lamin Dm0-derivatives (amino acid residues 549-622; fragment E). To supplement these data, we used 2-D tryptic peptide mapping followed by phosphorImager analysis. We routinely detected at least seven 'spots' derived from interphase lamins but only a single mitotic lamin phosphopeptide.     

Effects of sample handling temperatures on bovine skim milk progesterone concentrations

The effects of incubation of whole milk at various temperatures and times on the concentration of progesterone in the skim milk fraction was determined. For the study, milk samples were collected from 10 pregnant Holstein cows. The milk from each cow was transferred to culture tubes to provide 32 replicates of 3 ml volume. To begin the incubation study, all samples were placed in a 37 degrees C water bath for 4 h. The end of this incubation was designated as time 0 and a sample from each cow was centrifuged to harvest skim milk. At time 0, samples from each cow were divided among incubation temperatures of 0 degrees, 4 degrees, 20 degrees and 37 degrees C. Samples were removed from each incubation group at 30, 60, 90 and 120 min. After 120 min, all remaining samples were returned to the 37 degrees C incubation and skim milk was collected at 30, 60 and 90 min. Progesterone was measured in skim milk by radioimmunoassay. The mean +/- SE concentration of progesterone in skim milk at time 0 was 10.9 +/- 1.1 nmol/L. The mean concentration of progesterone in skim milk was higher (P < 0.05) in all samples incubated at 0 degrees and 4 degrees C, with incremental increases ranging from 34% to 67% above time 0. Progesterone in skim milk returned to time 0 concentrations in milk samples transferred from 0 degrees or 4 degrees C to 37 degrees C. There was no change in skim milk progesterone in whole milk samples incubated at 20 degrees or 37 degrees C. From this study, it can be concluded that the concentration of progesterone in skim milk is temperature dependent. Inconsistency in handling whole milk samples can have a profound effect in the concentration of progesterone on skim milk. The temperature-dependent effect was reversible and may be related to solubility of progesterone in milk fat.