Thermoluminescence properties of the rock naturally annealed for thousands of years by flames from the earth's inner layers

The gas leak in Chimaera near Çıralı, Antalya, has been active for thousands of years. It is also known to be the source of the first Olympic flame in the Hellenistic period. The sample taken from the Chimaere seepage annealed for thousands of years was determined to be calcite-magnesian (Ca, Mg)O₃. In this study, thermoluminescence (TL) properties of calcite-magnesian annealed for thousands of years in the fire caused by methane gas were investigated for particle size, dose–response, heating rate, and fading experiments. It exhibits a clear TL glow curve with two distinct peaks positioned at 160 and 330°C, and its shape is not affected by variation in applied dose and reproduciility of experiment. There is a wide linear relationship between TL output and applied dose up to 614 Gy. Although the positions of the TL peaks are stable with the cycle of measurement, a poor reusability was observed in terms of the area under the TL glow curve and peak intensity.     

Investigation of zinc polycarboxylate cement used in dental treatments in terms of retrospective dosimeter

Zinc polycarboxylate cement is one of the few dental materials that demonstrate true adhesion to tooth structure. It is suitable for use in living organisms without causing harm. Its strong adhesion to teeth and low level of irritancy are two important parameters for the dental applications. In this study, the dosimetry properties of zinc polycarboxylate cement using thermoluminescence (TL) method were investigated and determined the effectiveness of its use as a good dosimeter. According to the results of this study, the sample shows a good TL properties with three main peaks found around 140°C, 220°C and 330°C. It has a wide linear dose response between 72 Gy and 2.3 kGy and good reusability of the TL peak found at 330°C. Unfortunately, the TL peak intensity values are rapidly faded within a short waiting time interval. Zinc polycarboxylate cement, which is frequently used in dental crowns, can be used as a retrospective dosimeter for measuring the amount of radiation in space studies and nuclear accidents due to its wide linear dose–response curve in the high dose region.     

Thermoluminescence properties of gamma‐irradiated nano‐structure hydroxyapatite

The suitability of nano‐structured hydroxyapatite (HAP) for use as a thermoluminescence dosimeter was investigated. HAP samples were synthesized using a hydrolysis method. The formation of nanoparticles was confirmed by X‐ray diffraction and average particle size was estimated to be ~30 nm. The glow curve exhibited a peak centered at around 200 °C. The additive dose method was applied and this showed that the thermoluminescence (TL) glow curves follow first‐order kinetics due to the non‐shifting nature of T_m after different doses. The numbers of overlapping peaks and related kinetic parameters were identified from T_m–T_stop through computerized glow curve deconvolution methods. The dependence of the TL responses on radiation dose was studied and a linear dose response up to 1000 Gy was observed for the samples. Copyright © 2015 John Wiley & Sons, Ltd.     

Dosimetric properties of lithium borate glass doped with dysprosium

Characterization of thermoluminescence (TL) properties of lithium borate glass samples doped with different concentrations of dysprosium (Dy) was carried out. Samples were prepared using a melting method at 1100°C and irradiated with β‐particles. The glass samples doped with 0.1% Dy displayed the best TL dosimetric properties compared with other compositions. Deconvoluted analyses of the glow curves displayed five overlapping TL glow peaks located between 392.0 and 510.3 K. A good linear TL dose–response for β‐particles was obtained in the dose range 66.6 mGy to 33.3 Gy. The minimum detectible dose was evaluated to be 205.4 μGy and samples revealed thermal fading in 312 h to 29% of their original value.     

Thermoluminescence in pumice stone collected from the Mediterranean coast

Pumice is a low-density, light-coloured volcanic rock (igneous rock) formed when the magma from a volcanic eruption is suddenly cooled. It has a porous structure and can be different colours and have different densities. Pumice stone, unlike other rock, does not sink in water because it has a low density. In the present study, the thermoluminescent (TL) dosimetric characteristics, such as the dose–response, TL signal fading as a function of storage time, heating rate, and reusability of pumice collected on the Mediterranean coast were investigated. From this study, it was concluded that the pumice stone showed TL properties with a TL glow curve including an obviously wide peak at ∼200°C. A wide linear dose–response region up to 144 Gy, low fading of the TL signal when it was kept in a dark room for a long time, and poor reusability properties were observed for dosimetry use.     

Investigation of thermoluminescence glow curves in quartz extracted from the Central Eastern Desert,Egypt

The current study investigated the thermoluminescence (TL) properties of milky quartz samples collected from the Central Eastern Desert, Egypt. The crystallinity and the elemental concentrations of the milky quartz samples were examined using X‐ray diffraction and an atomic absorption spectrometer. Samples were irradiated using a gamma source at different doses from 250 mGy up to 2 kGy. For annealing, the samples were heated at 400°C for 1 h, followed by slow cooling. Kinetic analyses for the TL glow curves were performed using new designed TL deconvolution software. The glow curves were composed of six overlapped trapping sites at 428, 468, 498, 545, 586, and 639 K. The samples also displayed a linear dose–response from 0.25 Gy up to 20 Gy and a supralinear response from 20 Gy up to 200 Gy. The samples exhibited very low sensitivity for gamma radiation compared with LiF and the minimum detectable dose was 545 μGy. From its linear nature, it was observed that the sensitivity had changed. This study recommends starting measurements of these milky quartz samples after 4 days to give established measurements.     

Thermoluminescence dosimeter (TLD) studies of Ca10K(PO4)7:Dy phosphor for applications in radiation dosimetry

This study reports the thermoluminescence (TL) aspects of Ca₁₀K(PO₄)₇:Dy phosphor synthesized using a wet chemical method for the first time. The X-ray diffraction (XRD) results confirm the formation of the desired crystalline phase. Surface morphological studies reveal the formation of polyhedrons and agglomerations having an average diameter of 200 nm, while energy dispersive X-ray spectroscopy (EDS) data show the presence and composition of the elements in appropriate amounts. The effect of Dy doping concentration has been studied on the TL properties with exposure to gamma radiations from the Co-60 source. The best TL response has been observed for 5 mol% Dy doping concentration. The glow curve is simple and consists of a single peak at 130°C. The effect of the heating rate has been studied on the TL glow curve, and the heating rate of 5°C/s shows the best TL response. The various TL properties such as annealing conditions, dose–response, TL linearity, fading, and reusability of the prepared phosphor have been studied to check its suitability as a good TL dosimeter (TLD). TL characterization of the phosphor reports that the TL response is linear from 5- to 2000 Gy. The results show that this phosphor can be a good TLD for the dosimetry of gamma radiations from Co-60.     

Study of thermoluminescence in turtle shell fossils using radiation dosimetry

The present study describes for the first time thermoluminescence (TL) characterization of turtle shell. A fossil shell was collected from the Dongargaon area in the Chandrapur district of Maharashtra, India. TL was recorded and a comparative study of TL for the above material was performed to understand the special TL characteristics of the shell. The shell was irradiated with ⁶⁰Co γ‐radiation to study its TL properties. The sample displayed two good TL peaks at 135°C and 255°C. A linear dose–response curve for the irradiated sample was produced for the dose range 0.79–28.5 kGy; this sample of turtle shell (fossil) may be useful as a high dose dosimetry phosphor in this range. This geological sample was further characterized using X‐ray diffraction to confirm its phase structure and by scanning electron microscopy , Fourier transform infrared and wavelength dispersive X‐ray fluorescence spectroscopy to determine morphology, vibration, and elemental composition as ppm or percentage of the sample, respectively. Kinetic parameters of the TL glow peak were calculated using three different methods.     

Thermoluminescence characteristics of calcite with a Gaussian process regression model of machine learning

Thermoluminescence (TL) is defined as a luminescence phenomenon that can be detected when an insulator or semiconductor is thermally stimulated. Defective crystals store radiation until they are stimulated. Thermoluminescence is a method of monitoring the absorbed dose of dosimeters. The irradiation crystal is heated to 500°C to display the absorbed dose as a luminescent light. The TL dosimetric properties of calcite obtained from nature were investigated in this study. Machine learning was also examined using Gaussian process regression (GPR) for stimulated TL characteristics. According to the experimental output, the TL glow curve had two main peaks located at 90°C and 240°C with good dosimetric properties. In the four regression models of GPR, the data for the heating rate of 3°C s⁻¹ have the lowest residual.     

Effects of temperature and ultraviolet radiation on microbial foodweb structure: potential responses to global change

1. A series of growth experiments were conducted with natural plankton communities from a lake and river in northern Quebec, to evaluate the response of microbial foodweb structure to changes in ambient temperature and solar ultraviolet radiation (UVR). 2. Bioassays were incubated for 6 days at two temperatures (10 and 20 °C) and three near-surface irradiance conditions [photosynthetically active radiation (PAR) + UVA + UVB, PAR + UVA, and PAR only). 3. The concentration of total bacteria showed no net response to temperature, but the percentage of actively respiring bacteria, as measured with the cellular redox probe 5-cyano-2,3-ditolyl tetrazolium chloride (CTC), was up to 57% higher at 20 °C relative to 10 °C. Chlorophyll a concentrations in the < 2 μm size fraction also reacted strongly to temperature, with a net increase of up to 61% over the temperature range of 10–20 °C. 4. The UVR effects were small or undetectable for most of the measured variables; however, the percentage of actively respiring bacteria was significantly inhibited in the presence of UVR at 20 °C, decreasing by 29–48% on day 6 in the lake experiments and by 59% on day 2 in one river experiment. 5. The results show differential sensitivity to temperature among organisms of microbial communities in subarctic freshwaters, and a resilience by the majority of micro-organisms to their present UVR conditions. Microbial foodwebs in northern freshwaters appear to be relatively unresponsive to short-term (days) changes in UVR. However, the observed responses to temperature suggest that climate change could influence community structure, with warmer temperatures favouring picoplanktonic phototrophs and heterotrophs, and a shift in nanoplankton species composition and size structure.     

Effect of annealing temperature and dopant concentration on the thermoluminescence sensitivity in LiF:Mg,Cu,Ag material

LiF:Mg,Cu,Ag is a new dosimetry material that is similar to LiF:Mg,Cu,P in terms of dosimetric properties. The effect of the annealing temperature in the range of 200 to 350°C on the thermoluminescence (TL) sensitivity and the glow curve structure of this material at different concentrations of silver (Ag) was investigated. It has been demonstrated that the optimum values of the annealing temperature and the Ag concentration are 240°C and 0.1 mol% for better sensitivity, respectively. The TL intensity decreases at annealing temperatures lower than 240°C or higher than 240°C, reaching a minimum at 300°C and then again increases for various Ag concentrations. It was observed that the glow curve structure altered and the area under the low temperature peak as well as the area under the main dosimetric peak decreased with increasing annealing temperature. The position of the main dosimetric peak moved in the direction of higher temperatures, but at 320 and 350°C annealing temperatures, it shifted to lower temperatures. It was also observed that the TL sensitivity could partially be recovered by a combined annealing procedure.     

Thermoluminescence properties of annealed natural quartz after beta irradiation

Here we investigated the effects of annealing, heating rate and fading (after annealing at 800 °C) on the thermoluminescence (TL) glow curves of natural quartz (NQ). All of the samples were annealed at different temperatures between 100 °C and 800 °C and then irradiated with a beta dose of about 34 Gray (Gy), in order to determine the effects of annealing treatments on TL peaks of natural quartz. TL glow curves of the samples were recorded. It was observed that the intensities of TL peaks were strongly sensitive to annealing temperatures at 800 °C. The heating rate and fading effect of TL peaks of natural quartz were examined for the annealed samples at 800 °C for 30 min. It was observed that the intensities of the TL peaks were differently affected from heating rate and fading. Additionally, TL kinetic parameters (activation energy, frequency factor and order of kinetics) of all peaks were determined for annealed samples using a computerized glow curve deconvolution (CGCD) method and Mathematica software. Copyright © 2016 John Wiley & Sons, Ltd.     

Thermoluminescence characterization of Ag‐doped Li2B4O7 single crystal materials

In this study, the thermoluminescence (TL) characteristics of Ag‐doped and undoped lithium tetraborate (Li₂B₄O₇, LTB) materials, grown using the Czochralski method, were reported. The TL properties of LTB:Ag, such as glow curve structure, dose response, fading and reproducibility, were investigated. The glow curve of the Li₂B₄O₇:Ag single crystal consists of four peaks located at approximately 75, 130, 190 and 275°C; in undoped LTB, the single crystal shows a broad glow curve with peaks at 65, 90, 125, 160 and 190°C using a heating rate of 5°C/s in the 50–350°C temperature region. The high temperature peak of Ag‐doped sample at 275°C has a nonlinear dose response within the range from 33 mGy to 9 Gy. There is a linear response in the range of 33–800 mGy; after which, a sublinear region appears up to 9 Gy for Ag‐doped LTB single crystal. For undoped single crystal, the dose response is supralinear for low doses and linear for the region between 1 and 9 Gy. The thermal fading ratio of the undoped material is almost 60% for the high temperature peak after 7 days. Ag‐doped LTB single crystal exhibits different behaviour over a period of 7 days.     

The mechanism of cryohemolysis: by direct observation with the cryomicroscope and the electron microscope.

Blood films (3–8 μm thick) supported between two glass coverslips were frozen to ?20 °C. In the extracellular areas, ice cavities of the order of 0.2 μm separated by bands of dense plasma were evident when examined with the electron microscope; intracellular ice was not observed with the light microscope. Electron microscopy also showed the presence of intracellular ice particles of the order of 0.2–0.7 μm, these appeared as fine reticulations when observed with the light microscope. Upon gradual rewarming the following changes were observed: recrystallization in the extracellular matrix (?18 to ?8 °C), intracellular recrystallization (?13 to ?10 °C), transfer of water from erythrocytes to extracellular areas (?9 to ?7 °C), and melting and hemolysis (?6 to ?2 °C).Freezing of blood at ?3 °C and subsequent thawing did not cause hemolysis of the red cells. In blood frozen at ?3 °C and cooled to ?20 °C or frozen by abrupt exposure to 20 °C the erythrocytes hemolyzed in 7/16–11/16 of a second, whereas in blood frozen at ?3 °C and cooled to ?10 °C the cells hemolyzed in 5–15 sec even though the mode if lysis (i.e., uniform seepage of hemoglobin from the surface of the cell) was similar in all cases. This indicates that the presence of intracellular ice does not seem to play a major role in the injury to the erythrocytes. The mechanism of cryoinjury demonstrated by hemolysis has been discussed.     

PHOTOSYNTHESIS OF THE RED ALGA GASTROCLONIUM COULTERI (RHODOPHYTA) IN RESPONSE TO CHANGES IN TEMPERATURE,LIGHT INTENSITY,AND DESICCATION1

Previously reported transplantation experiments in the field showed that Gastroclonium coulteri (Harvey) Kylin could survive above its normal intertidal range (0.0–0.5 m above MLLW), except during periods of daytime low tides in spring. Net photosynthetic rate measurements in the laboratory were performed to determine which physical factors might determine the upper boundary for this species in the intertidal zone. Maximum net photosynthesis occurred between 15 and 20° C, but remained positive between 4 and 35° C. The air temperature extremes observed in the field were 2° C (only seen once) and 26° C. Net photosynthesis increased as expected with light intensity to the highest value obtainable in the laboratory, 1400 μEin m^?2 s^?1. Plants collected from the field under higher light intensity (up to 2000 μEin m^?2 s^?2) also showed high rates of photosynthesis. Neither the temperature nor light levels observed in the field were directly damaging to photosynthesis. Desiccation, however, resulted in a sharp decrease in both photosynthesis and respiration. G. coulteri fully recovered from successive daily treatments of about 35% desiccation, but not from successive treatments of 50% desiccation. One exposure to 70% desiccation allowed no recovery of photosynthetic capacity.     

Photoluminescence and thermoluminescence dosimetry properties of Ag/Y co-doped ZnO nanophosphor for radiation measurements

This work explores the thermoluminescence (TL) and photoluminescence (PL) properties of Ag/Y co-doped zinc oxide (ZnO) nanophosphor. The proposed dosimeter was prepared by the coprecipitation method and sintered at temperatures from 400°C to 1000°C in an air atmosphere. Raman spectroscopy was studied to investigate the structural features of this composition. The new proposed dosimeter revealed two peaks at 150°C and 175°C with a small shoulder at high temperature (225°C). The PL spectrum showed strong green emissions between 500 to 550 nm. The Raman spectrum showed many bands related to the interaction between ZnO, silver (Ag), and yttrium oxide (Y₂O₃). The rising sintering temperature enhanced the TL glow curve intensity. The Ag/Y co-doped ZnO nanophosphor showed an excellent linearity index within a dose from 1 to 4 Gy. The minimum detectable dose (MDD) of the Ag/Y co-doped ZnO nanopowder (pellets) equaled 0.518 mGy. The main TL properties were achieved in this work as follows: thermal fading (37% after 45 days at 1 and 4 Gy), optical fading (53% after 1 h and 68% after 6 h by exposure to sunlight), effective atomic number (27.6), and energy response (flat behavior from 0.1 to 1.3 MeV). Finally, the proposed material shows promising results nominated to be used for radiation measurements.     

Fracto‐mechanoluminescence and thermoluminescence properties of UV and γ‐irradiated Ca2Al2SiO7:Ce3+ phosphor

Ce³⁺‐doped calcium aluminosilicate phosphor was prepared by a combustion‐assisted method at an initiating temperature of 600°C. Structural characterization was carried out using X‐ray diffraction (XRD) and scanning electron microscopy (SEM). The absorption spectra of Ca₂Al₂SiO₇:Ce³⁺ showed an absorption edge at 230 nm. The optical characterization of Ca₂Al₂SiO₇:Ce³⁺ phosphor was investigated in a fracto‐mechanoluminescence (FML) and thermoluminescence (TL) study. The peak of ML intensity increased as the height of impact of the moving piston increased. The TL intensity of Ca₂Al₂SiO₇:Ce³⁺ was recorded for different exposure times of UV and γ‐irradiation and it was observed that TL intensity was maximum for a UV irradiation time of 30 min and for a γ‐dose of 1180 Gy. The TL intensity had three peaks for UV irradiation at temperatures 82°C, 125°C and 203°C. Also the TL intensity had a single peak at 152°C for γ‐irradiation. The TL and ML emission spectra of Ca₂Al₂SiO₇:Ce³⁺ phosphor showed maximum emission at 400 nm. The possible mechanisms involved in the TL and ML processes of the Ca₂Al₂SiO₇:Ce³⁺ phosphor are also explained. Copyright © 2015 John Wiley & Sons, Ltd.     

Synthesis,characterization and thermoluminescence studies of Mn‐doped ZnS nanoparticles

ZnS:Mn nanoparticles were prepared by a chemical precipitation method and characterized by X‐ray diffraction (XRD), field emission gun scanning electron microscope (FEGSEM), and high resolution transmission electron microscopy (HRTEM). Capping agent (mercaptoethanol) concentrations used were 0 M, 0.005 M, 0.01 M, 0.015 M, 0.025 M, 0.040 M, and 0.060 M, and resulted in nanoparticles sizes of 2.98 nm, 2.9 nm, 2.8 nm, 2.7 nm, 2.61 nm, 2.2 nm and 2.1 nm, respectively. The thermoluminescence (TL) glow curve was recorded by heating the sample exposed to UV‐radiation, at a fixed heating rate 1°C sec^–1. The TL intensity initially increased with temperature, attained a peak value I_m for a particular temperature, and then decreased with further increase in temperature. The peak TL intensity increased with decreasing nanoparticle size, whereas the temperature corresponding to the peak TL intensity decreased slightly with reducing nanocrystal size. As a consequence of increase in surface‐to‐volume ratio and increased carrier recombination rates, the TL intensity increased with decreasing nanoparticle size. It was found that, whereas activation energy slightly decreased with decreasing nanoparticle size, the frequency factor decreased significantly with reduction in nanoparticle size. Copyright © 2015 John Wiley & Sons, Ltd.     

Effects of Temperature and Humidity on Laser Diffraction Measurements to Jet Nebulizer and Comparison with NGI

Laser diffraction (LD) and next generation impactor (NGI) are commonly used for the evaluation of inhaled drug formulations. In this study, the effect of temperature and humidity on the assessment of the nebulizer particle size distribution (PSD) by LD was investigated, and the consistency between NGI and LD measurements was evaluated. There was an increase in particle size with higher temperature or lower humidity. The particle population with a diameter less than 1 μm was significant at a temperature of 5°C or at relative humidity >90%; however, the same particle population became undetectable when temperature increased to 39°C or at relative humidity of 30–45%. The results of the NGI and LD measurements of aerosol generated from three types of jet nebulizers were compared. A poor correlation between the NGI and LD measurements was observed for PARI LC (2.2 μm) (R ²?=?0.893) and PARI LC (2.9 μm) (R ²?=?0.878), while a relatively good correlation (R ²?=?0.977) was observed for the largest particle size nebulizer (PARI TIA (8.6 μm)). We conclude that the ambient environment and the nebulizer have significant impacts on the performance and consistency between these instruments. These factors should be controlled in the evaluation of inhaled aerosol drug formulations when these instruments are used individually or in combination.     

Synthesis and thermoluminescence characterizations of Sr2B5O9Cl:Dy3+ phosphor for TL dosimetry

The photoluminescence (PL) and thermoluminescence (TL) displayed by Dy‐activated strontium haloborate (Sr₂B₅O₉Cl) were studied. A modified solid‐state reaction was employed for the preparation of the phosphor. Photoluminescence spectra showed blue (484 nm) and yellow (575 nm) emissions due to incorporation of Dy³⁺ into host matrix. The Dy‐doped (0.5 mol%) Sr₂B₅O₉Cl was studied after exposure to γ‐irradiation and revealed a prominent glow curve at 261°C with a small hump around 143°C indicating that two types of traps were generated. The glow peak at the higher temperature side (261°C) was more stable than the lower temperature glow peak. The TL intensity was 1.17 times less than that of the standard CaSO₄:Dy thermoluminescence dosimetry (TLD) phosphor, the phosphor showed a linear dose–response curve for different γ‐ray irradiation doses (0.002–1.25 Gy) and fading of 5–7% was observed for higher temperature peaks upon storage. Trapping parameters and their estimated error values have been calculated by Chen's peak shape method and by the initial rise method. Values of activation energies estimated by both these techniques were comparable. The slight difference in activation energy values calculated by Chen's peak shape method indicated the formation of two kinds of traps Furthermore, slight differences in frequency values are due to various escaping and retrapping probabilities. Copyright © 2014 John Wiley & Sons, Ltd.