Alternative fuel properties of tall oil fatty acid methyl ester-diesel fuel blends

In this experimental work, tall oil methyl ester-diesel fuel blends as alternative fuels for diesel engines were studied. Tall oil methyl ester was produced by reacting tall oil fatty acids with methyl alcohol under optimum conditions. The blends of tall oil methyl ester-diesel fuel were tested in a direct injection diesel engine at full load condition. The effects of the new fuel blends on the engine performance and exhaust emission were tested. It was observed that the engine torque and power output with tall oil methyl ester-diesel fuel blends increased up to 6.1% and 5.9%, respectively. It was also seen that CO emissions decreased to 38.9% and NO(x) emissions increased up to 30% with the new fuel blends. The smoke opacity did not vary significantly.     

Influence of tall oil biodiesel with Mg and Mo based fuel additives on diesel engine performance and emission

The purpose of this study is to investigate influences of tall oil biodiesel with Mg and Mo based fuel additives on diesel engine performance and emission. Tall oil resinic acids were reacted with MgO and MoO(2) stoichiometrically for the production of metal-based fuel additives (combustion catalysts). The metal-based additives were added into tall oil biodiesel (B60) at the rate of 4 micromol/l, 8 micromol/l and 12 micromol/l for preparing test fuels. In general, both of the metal-based additives improved flash point, pour point and viscosity of the biodiesel fuel, depending on the rate of additives. A single cylinder DI diesel engine was used in the tests. Engine performance values did not change significantly with biodiesel fuels, but exhaust emission profile was improved. CO emissions and smoke opacity decreased by 56.42% and by 30.43%, respectively. In general, low NO(x) and CO(2) emissions were measured with the biodiesel fuels.     

Combustion characteristics of a turbocharged DI compression ignition engine fueled with petroleum diesel fuels and biodiesel

In this study, the combustion characteristics and emissions of two different petroleum diesel fuels (No. 1 and No. 2) and biodiesel from soybean oil were compared. The tests were performed at steady state conditions in a four-cylinder turbocharged DI diesel engine at full load at 1400-rpm engine speed. The experimental results compared with No. 2 diesel fuel showed that biodiesel provided significant reductions in PM, CO, and unburned HC, the NO(x) increased by 11.2%. Biodiesel had a 13.8% increase in brake-specific fuel consumption due to its lower heating value. However, using No. 1 diesel fuel gave better emission results, NO(x) and brake-specific fuel consumption reduced by 16.1% and 1.2%, respectively. The values of the principal combustion characteristics of the biodiesel were obtained between two petroleum diesel fuels. The results indicated that biodiesel may be blended with No. 1 diesel fuel to be used without any modification on the engine.     

Improvement of engine emissions with conventional diesel fuel and diesel-biodiesel blends

In this report combustion and exhaust emissions with neat diesel fuel and diesel-biodiesel blends have been investigated. In the investigation, firstly biodiesel from non-edible neem oil has been made by esterification. Biodiesel fuel (BDF) is chemically known as mono-alkyl fatty acid ester. It is renewable in nature and is derived from plant oils including vegetable oils. BDF is non-toxic, biodegradable, recycled resource and essentially free from sulfur and carcinogenic benzene. In the second phase of this investigation, experiment has been conducted with neat diesel fuel and diesel-biodiesel blends in a four stroke naturally aspirated (NA) direct injection (DI) diesel engine. Compared with conventional diesel fuel, diesel-biodiesel blends showed lower carbon monoxide (CO), and smoke emissions but higher oxides of nitrogen (NOx) emission. However, compared with the diesel fuel, NOx emission with diesel-biodiesel blends was slightly reduced when EGR was applied.     

Effects of mixing system and pilot fuel quality on diesel–biogas dual fuel engine performance

This paper describes results obtained from CI engine performance running on dual fuel mode at fixed engine speed and four loads, varying the mixing system and pilot fuel quality, associated with fuel composition and cetane number. The experiments were carried out on a power generation diesel engine at 1500 m above sea level, with simulated biogas (60% CH₄–40% CO₂) as primary fuel, and diesel and palm oil biodiesel as pilot fuels. Dual fuel engine performance using a naturally aspirated mixing system and diesel as pilot fuel was compared with engine performance attained with a supercharged mixing system and biodiesel as pilot fuel. For all loads evaluated, was possible to achieve full diesel substitution using biogas and biodiesel as power sources. Using the supercharged mixing system combined with biodiesel as pilot fuel, thermal efficiency and substitution of pilot fuel were increased, whereas methane and carbon monoxide emissions were reduced.     

Effects of biodiesel on emissions of a bus diesel engine

This paper discusses the influence of biodiesel on the injection, spray, and engine characteristics with the aim to reduce harmful emissions. The considered engine is a bus diesel engine with injection M system. The injection, fuel spray, and engine characteristics, obtained with biodiesel, are compared to those obtained with mineral diesel (D2) under various operating regimes. The considered fuel is neat biodiesel from rapeseed oil. Its density, viscosity, surface tension, and sound velocity are determined experimentally and compared to those of D2. The obtained results are used to analyze the most important injection, fuel spray, and engine characteristics. The injection characteristics are determined numerically under the operating regimes, corresponding to the 13 mode ESC test. The fuel spray is obtained experimentally under peak torque condition. Engine characteristics are determined experimentally under 13 mode ESC test conditions. The results indicate that, by using biodiesel, harmful emissions (NO(x), CO, smoke and HC) can be reduced to some extent by adjusting the injection pump timing properly.     

Biodiesel Production from Non-edible Oils of Jatropha and Karanj for Utilization in Electrical Generator

The biodiesel processor was developed for the production of biodiesel from non-edible oil of jatropha and karanj. The newly developed biodiesel processor is suitable for farmers in village level biodiesel production. The biodiesel processor was capable of producing 15 kg biodiesel per batch in 1.5 h at reaction temperature of 60°C. The biodiesel was produced from raw jatropha and karanj oil, and its blends with diesel were tested for power generation in a 7.5-kVA diesel engine generator set. The fuel properties, namely, kinematic viscosity and specific gravity, were found within the limits of Bureau of Indian Standards specifications. The overall efficiency of the generator for 4,500 W loading condition of jatropha- and karanj-biodiesel-blended fuel were recorded in the range of 21–23% and 24–27%, respectively. The overall efficiency of the generator for 6,000 W loading conditions was improved for jatropha and karanj biodiesel blends and were found in the range of 31–33% and 33–39%, respectively. Biodiesel blends B80 and pure biodiesel of karanj produced more power, and maximum overall efficiency was recorded as compared with diesel fueled generator. The overall efficiency on jatropha-biodiesel-blended fuel were found less than the diesel-fueled generator. The biodiesel processor based on alkali-catalyzed transesterification process can be used for quality biodiesel production from edible and non-edible vegetable oils. This processor can be integrated with rural energy system for domestic and small-scale industrial unit for biodiesel production.     

Ethanol-diesel fuel blends -- a review

Ethanol is an attractive alternative fuel because it is a renewable bio-based resource and it is oxygenated, thereby providing the potential to reduce particulate emissions in compression-ignition engines. In this review the properties and specifications of ethanol blended with diesel fuel are discussed. Special emphasis is placed on the factors critical to the potential commercial use of these blends. These factors include blend properties such as stability, viscosity and lubricity, safety and materials compatibility. The effect of the fuel on engine performance, durability and emissions is also considered. The formulation of additives to correct certain key properties and maintain blend stability is suggested as a critical factor in ensuring fuel compatibility with engines. However, maintaining vehicle safety with these blends may entail fuel tank modifications. Further work is required in specifying acceptable fuel characteristics, confirming the long-term effects on engine durability, and ensuring safety in handling and storing ethanol-diesel blends.     

The use of a fuel containing Chlorella vulgaris in a diesel engine

There is a need for sustainable fuels for diesel engines and fuels containing particles will function as a fuel in diesel engines. Some microalgae such as Chlorella vulgaris are unicellular and 5–10 μm in size, which is suitable for combining in an emulsion fuel. An emulsion consisting of transesterified rapeseed oil, a surfactant and a slurry of C. vulgaris was used as a fuel in an unmodified single cylinder diesel engine. The fuel consumption and emissions of this fuel was determined and although the carbon monoxide levels were higher the NO_x emission was lower than that of diesel.     

Experimental study of the spray characteristics of biodiesel based on inedible oil

We studied the spray characteristics of inedible oil using experimental and simulation methods. Spray penetration, spray cone angle and spray tip speed were measured at different biodiesel ratios in a constant volume vessel with wide visualization and high back pressure, using a high-speed camera. The characteristics of biodiesel spray were simulated under the same conditions using Star-CD software. The experimental results showed that, as the ratio of biodiesel in the blends increased, spray penetration and spray speed increased, but the spray cone angle decreased. Throughout the spray injection period, the region at 0.05–0.475S (spray tip penetration) was a key area affecting spray cone angle. From 0.8 ms after injection, the spray penetration deviation ratios started to increase with increasing biodiesel blend ratios. Simulation results showed similar macroscopic spray characteristics to the experimental results for jatropha oil. The results also showed that the Sauter mean diameter of blend fuels was greater than that of diesel, and spray was more concentrated, due to the higher viscosity and surface tension of the biodiesel, compared with conventional diesel fuel. The macroscopic and microscopic spray properties of blended fuels containing 5%, 10% and 20% biodiesel were similar to diesel.     

Biodegradation of diesel/biodiesel blends by a consortium of hydrocarbon degraders: effect of the type of blend and the addition of biosurfactants

Biodegradation experiments for diesel/biodiesel blends in liquid cultures by-petroleum degrading microbial consortium showed that for low amendments of biodiesel (10%) the overall biodegradation efficiency of the mixture after seven days was lower than for petroleum diesel fuel. Preferential usage of methyl esters in the broad biodiesel concentration range and diminished biodegradation of petroleum hydrocarbons for 10% biodiesel blend was confirmed. Rhamnolipids improved biodegradation efficiency only for blends with low content of biodiesel. Emulsion formation experiments showed that biodiesel amendments significantly affected dispersion of fuel mixtures in water. The presence of rhamnolipids biosurfactant affected stability of such emulsions and altered cell surface properties of tested consortium.     

Combustion behaviors of a compression-ignition engine fueled with diesel/methanol blends under various fuel delivery advance angles

A stabilized diesel/methanol blend was described and the basic combustion behaviors based on the cylinder pressure analysis was conducted in a compression-ignition engine. The study showed that increasing methanol mass fraction of the diesel/methanol blends would increase the heat release rate in the premixed burning phase and shorten the combustion duration of the diffusive burning phase. The ignition delay increased with the advancing of the fuel delivery advance angle for both the diesel fuel and the diesel/methanol blends. For a specific fuel delivery advance angle, the ignition delay increased with the increase of the methanol mass fraction (oxygen mass fraction) in the fuel blends and the behaviors were more obvious at low engine load and/or high engine speed. The rapid burn duration and the total combustion duration increased with the advancing of the fuel delivery advance angle. The centre of the heat release curve was close to the top-dead-centre with the advancing of the fuel delivery advance angle. Maximum cylinder gas pressure increased with the advancing of the fuel delivery advance angle, and the maximum cylinder gas pressure of the diesel/methanol blends gave a higher value than that of the diesel fuel. The maximum mean gas temperature remained almost unchanged or had a slight increase with the advancing of the fuel delivery advance angle, and it only slightly increased for the diesel/methanol blends compared to that of the diesel fuel. The maximum rate of pressure rise and the maximum rate of heat release increased with the advancing of the fuel delivery advance angle of the diesel/methanol blends and the value was highest for the diesel/methanol blends.     

Life cycle assessment of biofuels from Jatropha curcas in West Africa: a field study

In recent years, liquid biofuels for transport have benefited from significant political support due to their potential role in curbing climate change and reducing our dependence on fossil fuels. They may also participate to rural development by providing new markets for agricultural production. However, the growth of energy crops has raised concerns due to their high consumption of conventional fuels, fertilizers and pesticides, their impacts on ecosystems and their competition for arable land with food crops. Low-input species such as Jatropha curcas , a perennial, inedible crop well adapted to semiarid regions, has received much interest as a new alternative for biofuel production, minimizing adverse effects on the environment and food supply. Here, we used life-cycle assessment to quantify the benefits of J. curcas biofuel production in West Africa in terms of greenhouse gas emissions and fossil energy use, compared with fossil diesel fuel and other biofuels. Biodiesel from J. curcas has a much higher performance than current biofuels, relative to oil-derived diesel fuels. Under West Africa conditions, J. curcas biodiesel allows a 72% saving in greenhouse gas emissions compared with conventional diesel fuel, and its energy yield (the ratio of biodiesel energy output to fossil energy input) is 4.7. J. curcas production studied is eco-compatible for the impacts under consideration and fits into the context of sustainable development.     

Absorptive removal of biomass tar using water and oily materials

Water is the most common choice of absorption medium selected in many gasification systems. Because of poor solubility of tar in water, hydrophobic absorbents (diesel fuel, biodiesel fuel, vegetable oil, and engine oil) were studied on their absorption efficiency of biomass tar and compared with water. The results showed that only 31.8% of gravimetric tar was removed by the water scrubber, whereas the highest removal of gravimetric tar was obtained by a vegetable oil scrubber with a removal efficiency of 60.4%. When focusing on light PAH tar removal, the absorption efficiency can be ranked in the following order; diesel fuel > vegetable oil > biodiesel fuel > engine oil > water. On the other hand, an increase in gravimetric tar was observed for diesel fuel and biodiesel fuel scrubbers because of their easy evaporation. Therefore, the vegetable oil is recommended as the best absorbent to be used in gasification systems.     

Current and Potential Biofuel Production from Plant Oils

Environmental concerns and depletion of fossil fuels along with government policies have led to the search for alternative fuels from various renewable and sustainable feedstocks. This review provides a critical overview of the chemical composition of common commercial plant oils, i.e., palm oil, olive oil, rapeseed oil, castor oil, WCO, and CTO and their recent trends toward potential biofuel production. Plant oils with a high energy content are primarily composed of triglycerides (generally >?95%), accompanied by diglycerides, monoglycerides, and free fatty acids. The heat content of plant oils is close to 90% for diesel fuels. The oxygen content is the most important difference in chemical composition between fossil oils and plant oils. Triglycerides can even be used directly in diesel engines. However, their high viscosity, low volatility, and poor cold flow properties can lead to engine problems. These problems require that plant oils need to be upgraded if they are to be used as a fuel in conventional diesel engines. Biodiesel, biooil, and renewable diesel are the three major biofuels obtained from plant oils. The main constraint associated with the production of biodiesel is the cost and sustainability of the feedstock. The renewable diesel obtained from crude tall oil is more sustainable than biofuels obtained from other feedstocks. The fuel properties of renewable diesel are similar to those of fossil fuels with reduced greenhouse gas emissions. In this review, the chemical composition of common commercial plant oils, i.e., palm oil, olive oil, rapeseed oil, castor oil, and tall oil, are presented. Both their major and minor components are discussed. Their compositions and fuel properties are compared to both fossil fuels and biofuels.     

Effect of operating and sampling conditions on the exhaust gas composition of small-scale power generators

Small stationary diesel engines, like in generator sets, have limited emission control measures and are therefore responsible for 44% of the particulate matter (PM) emissions in the United States. The diesel exhaust composition depends on operating conditions of the combustion engine. Furthermore, the measurements are influenced by the used sampling method. This study examines the effect of engine loading and exhaust gas dilution on the composition of small-scale power generators. These generators are used in different operating conditions than road-transport vehicles, resulting in different emission characteristics. Experimental data were obtained for gaseous volatile organic compounds (VOC) and PM mass concentration, elemental composition and nitrate content. The exhaust composition depends on load condition because of its effect on fuel consumption, engine wear and combustion temperature. Higher load conditions result in lower PM concentration and sharper edged particles with larger aerodynamic diameters. A positive correlation with load condition was found for K, Ca, Sr, Mn, Cu, Zn and Pb adsorbed on PM, elements that originate from lubricating oil or engine corrosion. The nitrate concentration decreases at higher load conditions, due to enhanced nitrate dissociation to gaseous NO at higher engine temperatures. Dilution on the other hand decreases PM and nitrate concentration and increases gaseous VOC and adsorbed metal content. In conclusion, these data show that operating and sampling conditions have a major effect on the exhaust gas composition of small-scale diesel generators. Therefore, care must be taken when designing new experiments or comparing literature results.     

Correlation for the estimation of the density of fatty acid esters fuels and its implications. A proposed Biodiesel Cetane Index

Biodiesel fuels (methyl or ethyl esters derived from vegetables oils and animal fats) are currently being used as a means to diminish the crude oil dependency and to limit the greenhouse gas emissions of the transportation sector. However, their physical properties are different from traditional fossil fuels, this making uncertain their effect on new, electronically controlled vehicles. Density is one of those properties, and its implications go even further. First, because governments are expected to boost the use of high-biodiesel content blends, but biodiesel fuels are denser than fossil ones. In consequence, their blending proportion is indirectly restricted in order not to exceed the maximum density limit established in fuel quality standards. Second, because an accurate knowledge of biodiesel density permits the estimation of other properties such as the Cetane Number, whose direct measurement is complex and presents low repeatability and low reproducibility. In this study we compile densities of methyl and ethyl esters published in literature, and proposed equations to convert them to 15 °C and to predict the biodiesel density based on its chain length and unsaturation degree. Both expressions were validated for a wide range of commercial biodiesel fuels. Using the latter, we define a term called Biodiesel Cetane Index, which predicts with high accuracy the Biodiesel Cetane Number. Finally, simple calculations prove that the introduction of high-biodiesel content blends in the fuel market would force the refineries to reduce the density of their fossil fuels.     

Influence of fatty acid methyl esters from hydroxylated vegetable oils on diesel fuel lubricity

Current and future regulations on the sulfur content of diesel fuel have led to a decrease in lubricity of these fuels. This decreased lubricity poses a significant problem as it may lead to wear and damage of diesel engines, primarily fuel injection systems. Vegetable oil based diesel fuel substitutes (biodiesel) have been shown to be clean and effective and may increase overall lubricity when added to diesel fuel at nominally low levels. Previous studies on castor oil suggest that its uniquely high level of the hydroxy fatty acid ricinoleic acid may impart increased lubricity to the oil and its derivatives as compared to other vegetable oils. Likewise, the developing oilseed Lesquerella may also increase diesel lubricity through its unique hydroxy fatty acid composition. This study examines the effect of castor and Lesquerella oil esters on the lubricity of diesel fuel using the High-Frequency Reciprocating Rig (HFRR) test and compares these results to those for the commercial vegetable oil derivatives soybean and rapeseed methyl esters.     

The effect of fuel composition on the mutagenicity of diesel engine exhaust

The effect of fuel composition on the mutagenicity of diesel engine emission was investigated. To this end, a fuel matrix comprising fuels with different contents of aromatic and naphthenic compounds was used. Extracts of the organic phase of raw exhausts obtained with different fuels were tested for mutagenicity in bacterial reversion assays. The results obtained demonstrate that the mutagenicity of diesel exhaust is largely dependent on the aromatic content of the fuel. In fact, mutagenicity was greatly reduced when the aromatic content of the fuel was lowered by hydrogen treatment. Conversely, mutagenicity was enhanced when the fuel was enriched with fractions of di- or triaromatic compounds. The addition of di- and trinaphthenic compounds only produced borderline mutagenicity. No clear relationship was observed between sulfur content of the fuel and mutagenicity of the exhaust. Assays in bacterial strains with different sensitivity to nitroaromatic compounds suggest a low contribution of the highly mutagenic dinitropyrenes to the responses observed, and a relatively greater contribution of 1-nitropyrene or other nitroaromatics processed by the same bacterial nitroreductase.     

Microbial growth studies in biodiesel blends

Introduction of biofuels to the fuel matrix poses new questions and challenges. The present study investigates the microbiological stability of biodiesel blends in small scale microcosms. The study presents results from incubations of diesel-biodiesel blends with contaminated inoculation water collected from diesel storage tanks to ensure the presence of relevant fuel degrading bacteria. DAPI and qPCR analyses has subsequently shown an increased bacterial growth and activity in the microcosms containing biodiesel blends as the carbon source compared to those microcosms where neat fossil diesel made up the carbon source. Several anaerobic microorganisms have been identified after incubation. Presence of methanogens, sulfate-reducing bacteria and nitrate reducing bacteria has furthermore been confirmed by chemical analyses, supplemented by observations of methane formation in biodiesel incubations. The findings will contribute to the knowledge base for a safer introduction of biodiesel in the fuel matrix by employment of proper house-keeping and monitoring methods.