Screening Microalgae Strains for Biodiesel Production: Lipid Productivity and Estimation of Fuel Quality Based on Fatty Acids Profiles as Selective Criteria

The viability of algae-based biodiesel industry depends on the selection of adequate strains in regard to profitable yields and oil quality. This work aimed to bioprospecting and screening 12 microalgae strains by applying, as selective criteria, the volumetric lipid productivity and the fatty acid profiles, used for estimating the biodiesel fuel properties. Volumetric lipid productivity varied among strains from 22.61 to 204.91 mg l^?1 day^?1. The highest lipid yields were observed for Chlorella (204.91 mg l^?1 day¹) and Botryococcus strains (112.43 and 98.00 mg l^?1 day^?1 for Botryococcus braunii and Botryococcus terribilis, respectively). Cluster and principal components analysis analysis applied to fatty acid methyl esters (FAME) profiles discriminated three different microalgae groups according to their potential for biodiesel production. Kirchneriella lunaris, Ankistrodesmus fusiformis, Chlamydocapsa bacillus, and Ankistrodesmus falcatus showed the highest levels of polyunsaturated FAME, which incurs in the production of biodiesels with the lowest (42.47–50.52) cetane number (CN), the highest (101.33–136.97) iodine values (IV), and the lowest oxidation stability. The higher levels of saturated FAME in the oils of Chlamydomonas sp. and Scenedesmus obliquus indicated them as source of biodiesel with higher oxidation stability, higher CN (63.63–64.94), and lower IV (27.34–35.28). The third group, except for the Trebouxyophyceae strains that appeared in isolation, are composed by microalgae that generate biodiesel of intermediate values for CN, IV, and oxidation stability, related to their levels of saturated and monosaturated lipids. Thus, in this research, FAME profiling suggested that the best approach for generating a microalgae-biodiesel of top quality is by mixing the oils of distinct cell cultures.     

<Emphasis Type="Italic">Fremyella diplosiphon</Emphasis> as a Biodiesel Agent: Identification of Fatty Acid Methyl Esters via Microwave-Assisted Direct In Situ Transesterification

Increasing concerns on environmental and economic issues linked to fossil fuel use has driven great interest in cyanobacteria as third-generation biofuel agents. In this study, the biodiesel potential of a model photosynthetic cyanobacterium, Fremyella diplosiphon, was identified by fatty acid methyl esters (FAME) via direct transesterification. Total lipids in wild type (Fd33) and halotolerant (HSF33-1 and HSF33-2) strains determined by gravimetric analysis yielded 19% cellular dry weight (CDW) for HSF33-1 and 20% CDW for HSF33-2, which were comparable to Fd33 (18% CDW). Gas chromatography-mass spectrometry detected a high ratio of saturated to unsaturated FAMEs (2.48–2.61) in transesterified lipids, with methyl palmitate being the most abundant (C16:0). While theoretical biodiesel properties revealed high cetane number and oxidative stability, high cloud and pour point values indicated that fuel blending could be a viable approach. Significantly high FAME abundance in total transesterified lipids of HSF33-1 (40.2%) and HSF33-2 (69.9%) relative to Fd33 (25.4%) was identified using comprehensive two-dimensional gas chromatography coupled to time-of-flight mass spectrometry, indicating that robust salt stress response corresponds to higher levels of extractable FAME. Alkanes, a key component in conventional fuels, were present in F. diplosiphon transesterified lipids across all strains confirming that natural synthesis of these hydrocarbons is not inhibited during biodiesel production. While analysis of photosynthetic pigments and phycobiliproteins did not reveal significant differences, FAME abundance varied significantly in wild type and halotolerant strains indicating that photosynthetic pathways are not the sole factors that determine fatty acid production. We characterize the potential of F. diplosiphon for biofuel production with FAME yields in halotolerant strains higher than the wild type with no loss in photosynthetic pigmentation.     

Comparative Analysis of the Fatty Acid Composition of Microalgae Obtained by Different Oil Extraction Methods and Direct Biomass Transesterification

One of the main challenges for the successful production and use of microalgae for biodiesel production is to obtain a satisfactory level of fatty acid methyl esters (FAME). The aims of this study are to identify the best method of lipid extraction and provide high FAME levels and to evaluate their fatty acid profiles. Six lipid extraction methodologies in three microalgae species were tested in comparison with the direct transesterification (DT) of microalgal biomass method. The choice of extraction method affected both the oily extract yield and the FAME composition of the microalgae and consequently may affect the properties of biodiesel. The efficiency of different lipid extraction methods is affected by the solvent polarity, which extracts different target compounds from lipid matrix. Dichloromethane/methanol extraction and Folch extraction produced the largest oil extract yields, but extraction with hexane/ethanol resulted in the best ester profile and levels. Performing DT reduces the volume of extractor solvent, the time and cost of FA composition analysis, as well as, presents less steps for fatty acid quantification. DT provided biomass FAME levels of 50.2, 636.4, and 258.2 mg.g^?1 in Nannochlorophisis oculata, Chaetoceros muelleri, and Chlorella sp., respectively. On the basis of an analysis of the fatty acids profiles of different species, C. muelleri is a promising microalga for biodiesel production. Depending on the extraction method, Chlorella sp. and N. oculata can be considered as an alternative in obtaining arachidonic (Aa) and eicosapentaenoic (EPA) acids.     

Lipid Extraction from <Emphasis Type="Italic">Tetraselmis</Emphasis> sp. Microalgae for Biodiesel Production Using Hexane-based Solvent Mixtures

Lipid extraction is a critical step in the downstream processing of biodiesel production from microalgae. Solvent extraction using mixtures of non-polar and polar solvents is one of the most well-known processes for this purpose. Hexane is the most common solvent of choice for large-scale lipid extractions due to its technical and economic advantages, especially its high selectivity toward lipids and low cost. In this study, extractions using mixtures of hexane and polar solvents were evaluated for their performance in order to develop a more efficient method for large-scale lipid extraction from microalgae. The combination of hexane and methanol resulted in the highest fatty acid methyl ester (FAME) yield for lipids from Tetraselmis sp. The effects of extraction conditions, including proportions of methanol to hexane, ratios of total solvent volume to dry biomass, and extraction time, on extraction yields were evaluated to determine optimum conditions providing higher lipid and FAME yields. The optimal conditions were as follows: proportion of hexane to methanol of 1:1, ratio of total solvent volume to dry biomass of 10 mL/g, and extraction time of 120 min. Finally, the selected solvent mixture and optimal conditions were applied to larger scale extraction experiments with scale-up factors of 10, 50, and 100. FAME yields of large-scale extractions were almost completely consistent with increasing scale-up factors. The results of this study suggest that a hexane and methanol mixture is a promising solvent for large-scale lipid extraction from microalgae.     

Methanol-free biosynthesis of fatty acid methyl ester (FAME) in Synechocystis sp. PCC 6803

To meet the increasing global demand of biodiesel over the next decades, alternative methods for producing one of the key constituents of biodiesel (e.g. fatty acid methyl esters (FAMEs)) are needed. Algal biodiesel has been a long-term target compromised by excessive costs for harvesting and processing. In this work, we engineered cyanobacteria to convert carbon dioxide into excreted FAME, without requiring methanol as a methyl donor. To produce FAME, acyl-ACP, a product of the fatty acid biosynthesis pathway, was first converted into free fatty acid (FFA) by a thioesterase, namely ’UcFatB1 from Umbellularia californica. Next, by employing a juvenile hormone acid O-methyltransferase (DmJHAMT) from Drosophila melanogaster and S-adenosylmethionine (SAM) as a methyl donor, FFAs were converted into corresponding FAMEs. The esters were naturally secreted extracellularly, allowing simple product separation by solvent overlay as opposed to conventional algae biodiesel production where the algae biomass must first be harvested and processed for transesterification of extracted triacylglycerols (TAGs). By optimizing both the promoter and RBS elements, up to 120 mg/L of FAMEs were produced in 10 days. Quantification of key proteins and metabolites, together with constructs over-expressing SAM synthetase (MetK), indicated that ’UcFatB1, MetK, and DmJHAMT were the main factors limiting pathway flux. In order to solve the latter limitation, two reconstructed ancestral sequences of DmJHAMT were also tried, resulting in strains showing a broader methyl ester chain-length profile in comparison to the native DmJHAMT. Altogether, this work demonstrates a promising pathway for direct sunlight-driven conversion of CO₂ into excreted FAME.     

Effect of nitrate on lipid production by T. suecica, M. contortum, and C. minutissima

Microalgae are an alternative and sustainable source of lipids that can be used as a feedstock for biodiesel production. Nitrate is a good nitrogen source for many microalgae and affects biomass and lipid yields of microalgae. In this study, the effect of nitrate on cell growth and lipid production and composition in Monoraphidium contortum, Tetraselmis suecica, and Chlorella minutissima was investigated. Nitrate affected the production of biomass and the production and composition of lipids of the three microalgae tested. Increasing the nitrate concentration in the culture medium resulted in increased biomass production and higher biomass productivity. Furthermore, increasing the nitrate concentration resulted in a reduction in lipid content and productivity in M. contortum; however, the opposite effect was observed in T. suecica and C. minutissima cultures. C. minutissima and M. contortum lipids contain high levels of oleic acid, with values ranging from 26 to 45.7% and 36.4 to 40.1%, respectively. The data suggest that because of its high lipid productivity (13.79 mg L^?1 d^?1) and high oleic acid productivity (3.78 mg L^?1 d^?1), Chlorella minutissima is a potential candidate for the production of high quality biodiesel.     

Profiling of fatty acid methyl esters from the oleaginous diatom Fistulifera sp. strain JPCC DA0580 under nutrition-sufficient and -deficient conditions

The marine oleaginous diatom, Fistulifera sp. strain JPCC DA0580, is a promising candidate for biodiesel production due to its high lipid content. In order to truly evaluate the potential of this strain as biodiesel feedstock as well as the impact of nutrition-deficiency to this strain, the proportion of the lipid fractions and fatty acid methyl ester (FAME) derived from Fistulifera sp. cultured under nutrition-sufficient or -deficient conditions were analyzed. The nutrition deficiency led to the increase of the total lipid content in the form of neutral lipids (NLs) accumulation and the decline of polar lipids compared with nutrition-sufficiency. Meanwhile, the total lipid productivity was not significantly changed under two nutrition conditions while the NL productivity under nutrition-deficient condition was much higher than nutrition-sufficient condition. The major FAME components, C14:0, C16:0, C16:1, and C20:5, contribute to over 90 % of total FAMEs under both nutrition conditions. A lower polyunsaturated FAME level were observed in the nutrition-deficient condition (9.9?±?0.2 %) compared with the nutrition-sufficient condition (19.8?±?1.2 %), suggesting the availability of the nutrition stress on the strain JPCC DA0580 for improvement of fuel quality as well as productivity. The lipid quality estimation based on the FAME profile revealed that the nutrition-deficiency could further improve the lipid quality of both total lipids and NL fraction. In addition, direct infusion ESI-Q-TRAP-MS/MS was carried out for the fractionated NL in order to estimate triacylglycerol (TAG) composition, suggesting a crucial role of the chloroplast in TAG synthesis.     

Production of algae-based biodiesel using the continuous catalytic Mcgyan® process

This study demonstrates the production of algal biodiesel from Dunaliella tertiolecta, Nannochloropsis oculata, wild freshwater microalgae, and macroalgae lipids using a highly efficient continuous catalytic process. The heterogeneous catalytic process uses supercritical methanol and porous titania microspheres in a fixed bed reactor to catalyze the simultaneous transesterification and esterification of triacylglycerides and free fatty acids, respectively, to fatty acid methyl esters (biodiesel). Triacylglycerides and free fatty acids were converted to alkyl esters with up to 85% efficiency as measured by 300 MHz ¹H NMR spectroscopy. The lipid composition of the different algae was studied gravimetrically and by gas chromatography. The analysis showed that even though total lipids comprised upwards of 19% of algal dry weight the saponifiable lipids, and resulting biodiesel, comprised only 1% of dry weight. Thus highlighting the need to determine the triacylglyceride and free fatty acid content when considering microalgae for biodiesel production.     

Lipid Profile Remodeling in Response to Nitrogen Deprivation in the Microalgae Chlorella sp. (Trebouxiophyceae) and Nannochloropsis sp. (Eustigmatophyceae)

Many species of microalgae produce greatly enhanced amounts of triacylglycerides (TAGs), the key product for biodiesel production, in response to specific environmental stresses. Improvement of TAG production by microalgae through optimization of growth regimes is of great interest. This relies on understanding microalgal lipid metabolism in relation to stress response in particular the deprivation of nutrients that can induce enhanced TAG synthesis. In this study, a detailed investigation of changes in lipid composition in Chlorella sp. and Nannochloropsis sp. in response to nitrogen deprivation (N-deprivation) was performed to provide novel mechanistic insights into the lipidome during stress. As expected, an increase in TAGs and an overall decrease in polar lipids were observed. However, while most membrane lipid classes (phosphoglycerolipids and glycolipids) were found to decrease, the non-nitrogen containing phosphatidylglycerol levels increased considerably in both algae from initially low levels. Of particular significance, it was observed that the acyl composition of TAGs in Nannochloropsis sp. remain relatively constant, whereas Chlorella sp. showed greater variability following N-deprivation. In both algae the overall fatty acid profiles of the polar lipid classes were largely unaffected by N-deprivation, suggesting a specific FA profile for each compartment is maintained to enable continued function despite considerable reductions in the amount of these lipids. The changes observed in the overall fatty acid profile were due primarily to the decrease in proportion of polar lipids to TAGs. This study provides the most detailed lipidomic information on two different microalgae with utility in biodiesel production and nutraceutical industries and proposes the mechanisms for this rearrangement. This research also highlights the usefulness of the latest MS-based approaches for microalgae lipid research.     

An alternative strategy for enhancing lipid accumulation in chlorophycean microalgae for biodiesel production

Oleaginous microalgae are considered as important feedstocks for production of biodiesel. Under nutrient stress conditions, microalgae have the ability to accumulate higher amount of lipids, which can be transesterified for the production of biodiesel. In the present investigation, four different phosphate application strategies were examined in five green microalgae (Tetradesmus obliquus, Tetradesmus lagerheimii, Chlorella vulgaris, Chlorella minutissima, and Chlamydomonas sp.) to achieve higher lipid productivity. Effects of those strategies such as phosphate-sufficient (Control), phosphate-starved approach (PSA), biphasic phosphate-starved approach (BPSA), and sequential phosphate addition (SPA) were studied under batch culture mode. The BPSA emerging as the best in terms of lipid productivity consisted of two biomass harvesting phases, which would lead to an increase in the overall cost of biodiesel production. On the other hand, the SPA with a 1/200th dose of N 11 medium, i.e., 0.4 mg L^?1 of phosphate application in 3-day intervals, also resulted into higher lipid productivity which was equal to BPSA. Fatty acid composition of the biodiesel obtained from the microalgae was analyzed and the fuel characteristics were also evaluated. A profound (~14-fold) reduction in phosphorus requirements under the SPA mode with higher lipid productivity ensured qualitative biodiesel production and a lesser amount of phosphorus release, thus making the process eco-friendly.     

A comparison of lipid storage in Phaeodactylum tricornutum and Tetraselmis suecica using laser scanning confocal microscopy

Microalgae contain lipid bodies (LBs) composed of triacylglycerols, which can be converted to biodiesel. Here we demonstrate a method to study the accumulation patterns of LBs in different microalgae strains and culture conditions utilizing laser scanning confocal microscopy (LSCM) with BODIPY 505/515 (4,4-difluoro-1,3,5,7-tetramethyl-4-bora-3a,4a-diaza-s-indacene) staining, in parallel with Nile Red (9-diethylamino-5H-benzo-a-phenoxazine-5-one) fluorescence analysis of intracellular lipids in microplates. Phaeodactylum tricornutum and Tetraselmis suecica were selected as model organisms and monitored throughout the growth phases in standard and nitrogen-deficient growth conditions. Utilizing image quantification techniques, the number and morphology of LBs suggest that P. tricornutum accumulates lipids by merging with existing LBs, while T. suecica synthesizes new LBs. We observed that T. suecica accumulates a higher number of LBs and total volume of lipids per cell, while P. tricornutum accumulates only 1–2 LBs with a larger volume per LB. LSCM analysis complements Nile Red (NR) methods because LSCM provides three-dimensional images of lipid accumulation at a cellular level, while NR analysis can quickly monitor the total levels of intracellular lipids for phenotypic screening. Using NR analysis, we have observed that the optimal harvest date for P. tricornutum and T. suecica in standard cultivation conditions is 24 and 42 days, respectively. Comparison with nitrogen-deficient growth conditions is utilized as a model to confirm that LSCM and NR analysis can be used to study lipid storage and productivity for diverse growth conditions and various strains of microalgae.     

Assessment and comparison of the properties of biodiesel synthesized from three different types of wet microalgal biomass

In recent years, microalgae-based carbon-neutral biofuels (i.e., biodiesel) have gained considerable interest due to high growth rate and higher lipid productivity of microalgae during the whole year, delivering continuous biomass production as compared to vegetable-based feedstocks. Therefore, biodiesel was synthesized from three different microalgal species, namely Tetraselmis sp. (Chlorophyta) and Nannochloropsis oculata and Phaeodactylum tricornutum (Heterokontophyta), and the fuel properties of the biodiesel were analytically determined, unlike most studies which rely on estimates based on the lipid profile of the microalgae. These include density, kinematic viscosity, total and free glycerol, and high heating value (HHV), while cetane number (CN) and cold filter plugging point (CFPP) were estimated based on the fatty acid methyl ester profile of the biodiesel samples instead of the lipid profile of the microalgae. Most biodiesel properties abide by the ASTM D6751 and the EN 14214 specifications, although none of the biodiesel samples met the minimum CN or the maximum content of polyunsaturated fatty acids with ≥4 double bonds as required by the EN 14214 reference value. On the other hand, bomb calorimetric experiments revealed that the heat of combustion of all samples was on the upper limit expected for biodiesel fuels, actually being close to that of petrodiesel. Post-production processing may overcome the aforementioned limitations, enabling the production of biodiesel with high HHV obtained from lipids present in these microalgae.     

Fluorescent measurement of lipid content in the model organism Chlamydomonas reinhardtii

The green alga Chlamydomonas reinhardtii is one of the most studied microalgae, which has the potential to be used as a model system to study lipid metabolism. Establishment of a method in this organism for rapid and simple measurement of neutral lipids is desirable. Fluorescent measurement of neural lipids by Nile Red staining has been widely used in various cell types including microalgae. However, a systematic study of Nile Red staining to measure neutral lipids in Chlamydomonas has not been reported. Here, we show that Nile Red staining is suitable for relative and absolute quantification of neutral lipids as well as for possible large-scale screening for mutants defective in lipid accumulation. We have compared and optimized the factors involved Nile Red staining including solvents, cell concentration, staining time, and Nile Red concentration. We determined that 5 % DMSO with 1 μg mL^?1 Nile Red and 5–15-min time window after staining was optimal for measuring lipid content of cells within the range of 1 to 8?×?10⁶ cells mL^?1. The absolute quantification of neutral lipids could be achieved by standard addition method. In addition, we developed a protocol that could be potentially used for large-scale screening for cells with different lipid content. Thus, the work reported here provides timely needed techniques to facilitate Chlamydomonas to be used as a model organism for studying lipid metabolism for biodiesel production.     

Zero-waste biorefinery of oleaginous microalgae as promising sources of biofuels and biochemicals through direct transesterification and acid hydrolysis

Oleaginous microalgae are considered as promising sources of biofuels and biochemicals due to their high lipid content and other high-value components such as pigments, carbohydrate and protein. This study aimed to develop an efficient biorefinery process for utilizing all of the components in oleaginous microalgae. Acetone extraction was used to recover microalgal pigments prior to processes for the other products. Microalgal lipids were converted into biodiesel (fatty acid methyl ester, FAME) through a conventional two-step process of lipid extraction followed by transesterification, and alternatively a one-step direct transesterification. The comparable FAME yields from both methods indicate the effectiveness of direct transesterification. The operating parameters for direct transesterification were optimized through response surface methodology (RSM). The maximum FAME yield of 256 g/kg-biomass was achieved when using chloroform:methanol as co-solvents for extracting and reacting reagents at 1.35:1 volumetric ratio, 70 °C reaction temperature, and 120 min reaction time. The carbohydrate content in lipid-free microalgal biomass residues (LMBRs) was subsequently acid hydrolyzed into sugars under optimized conditions from RSM. The maximum sugar yield obtained was 44.8 g/kg-LMBRs and the protein residues were recovered after hydrolysis. This biorefinery process may contribute greatly to zero-waste industrialization of microalgae based biofuels and biochemicals.     

Analysis of Fatty Acid Content and Composition in Microalgae

A method to determine the content and composition of total fatty acids present in microalgae is described. Fatty acids are a major constituent of microalgal biomass. These fatty acids can be present in different acyl-lipid classes. Especially the fatty acids present in triacylglycerol (TAG) are of commercial interest, because they can be used for production of transportation fuels, bulk chemicals, nutraceuticals (ω-3 fatty acids), and food commodities. To develop commercial applications, reliable analytical methods for quantification of fatty acid content and composition are needed. Microalgae are single cells surrounded by a rigid cell wall. A fatty acid analysis method should provide sufficient cell disruption to liberate all acyl lipids and the extraction procedure used should be able to extract all acyl lipid classes.With the method presented here all fatty acids present in microalgae can be accurately and reproducibly identified and quantified using small amounts of sample (5 mg) independent of their chain length, degree of unsaturation, or the lipid class they are part of.This method does not provide information about the relative abundance of different lipid classes, but can be extended to separate lipid classes from each other.The method is based on a sequence of mechanical cell disruption, solvent based lipid extraction, transesterification of fatty acids to fatty acid methyl esters (FAMEs), and quantification and identification of FAMEs using gas chromatography (GC-FID). A TAG internal standard (tripentadecanoin) is added prior to the analytical procedure to correct for losses during extraction and incomplete transesterification.     

Combined silver-ion and reversed-phase high-performance liquid chromatography for the separation and identification of C20 metabolites of conjugated linoleic acid isomers in rat liver lipids

Reversed-phase high-performance liquid chromatography (RP-HPLC) and silver-ion high-performance liquid chromatography (Ag-HPLC) were successively combined for the separation of the longer-chain metabolites of conjugated linoleic acids (CLAs). Commercial silver nitrate-impregnated columns were used with an eluting solvent composed of a mixture of hexane–acetonitrile. Fatty acid methyl esters (FAMEs) from liver lipids of rats fed CLA were analysed. This method allowed separation both of the non-conjugated FAME, as C16:1, C18:2, C18:3, C20:4 and C22:5, but also the conjugated fatty acids like CLA, 8,12,14-20:3, 5,8,12,14-20:4 and 5,8,11,13-20:4. The presence of 8,11,13-20:3 is reported for the first time. This method is of interest for the isolation and identification of the C₂₀ conjugated metabolites that cannot be resolved by gas chromatography. Furthermore, it allows the isolation of FAME for further characterisation by GC–mass spectrometry (MS).     

Application of the standard addition method for the absolute quantification of neutral lipids in microalgae using Nile red

Microalgae are considered one of the best candidates for biofuel production due to their high content in neutral lipids, therefore, an accurate quantification of these lipids in microalgae is fundamental for the identification of the better candidates as biodiesel source.Nile red is a fluorescent dye widely employed for the quantification of neutral lipids in microalgae. Usually, the fluorescence intensity of the stained samples is correlated to the neutral lipid content determined with standard methods, in order to draw a standard curve and deduce the neutral lipids concentration of the unknown samples positioning their fluorescence intensity values on the curve.Standard methods used for the neutral lipids determination are laborious and often implying solvent extraction and/or other transformation (i.e. saponification or transesterification) of the sample. These methods are also time consuming and may give rise to an underestimation of the lipid content due to variable extraction yields.The approach described in this paper combines the standard addition method and the fluorometric staining using Nile red, avoiding the association of traditional neutral lipids quantification methods to the fluorometric determination. After optimization of instrument parameters and staining conditions, a linear correlation between the fluorescence intensity of each sample stained with the Nile red and its neutral lipids content deduced with the standard addition method was identified. The obtained curve allowed the direct determination of neutral lipids content maintaining a linearity range from 0.12 to 12 μg of neutral lipids per ml of sample, without need of pre-concentration. This curve was then used in the quantification of the neutral lipids content in culture of Skeletonema marinoi (Bacillariophyceae) at different days from the inoculum. This method was also successfully applied on Chaetoceros socialis (Bacillariophyceae) and Alexandrium minutum (Dinophyceae).     

Biodiesel production by in situ transesterification of municipal primary and secondary sludges

The potential of using municipal wastewater sludges as a lipid feedstock for biodiesel production was investigated. Primary and secondary sludge samples obtained from a municipal wastewater treatment plant in Tuscaloosa, AL were freeze-dried and subjected to an acid-catalyzed insitu transesterification process. Experiments were conducted to determine the effects of temperature, sulfuric acid concentration, and mass ratio of methanol to sludge on the yield of fatty acid methyl esters (FAMEs). Results indicated a significant interactive effect between temperature, acid concentration, and methanol to sludge mass ratio on the FAME yield for the insitu transesterification of primary sludge, while the FAME yield for secondary sludge was significantly affected by the independent effects of the three factors investigated. The maximum FAME yields were obtained at 75 degrees C, 5% (v/v) H(2)SO(4), and 12:1 methanol to sludge mass ratio and were 14.5% and 2.5% for primary and secondary sludge, respectively. Gas chromatography (GC) analysis of the FAMEs revealed a similar fatty acid composition for both primary and secondary sludge. An economic analysis estimated the cost of $3.23/gallon for a neat biodiesel obtained from this process at an assumed yield of 10% FAMEs/dry weight of sludge.     

Optimization of the biomass production of oil algae Chlorella minutissima UTEX2341

High production cost is a major obstacle to the extensive use of microalgae biodiesel. To cut the cost and achieve higher biomass productivity, Chlorella minutissima UTEX2341 was cultured under photoheterotrophic conditions. With the carbon, nitrogen and phosphorus concentration of 26.37, 2.61 and 0.03 g L?1 d?1 respectively, a maximum biomass productivity of 1.78 g L?1 d?1 was obtained, which was 59 times more than that cultured under autotrophic condition. The lipid productivity reached 0.29 g L?1 d?1, which was 11.9 times higher than the highest value reported by Oh et al. (2010). The conversion rate of microalgae lipids to FAME was found to be elevated from 45.65% to 62.97% and the FAME productivity increased from 1.16 to 180.68 mg L?1 d?1 after the optimization. 94% of the fatty acid of C. minutissima UTEX2341 was found to be composed of palmitic, oleic, linoleic and γ linoleic and the unsaturated fatty acids were the main parts (79.42%).     

The effect of temperature on growth and lipid and fatty acid composition on marine microalgae used for biodiesel production

Cultivation temperature is one of the major factors affecting the growth and lipid accumulation of microalgae. In this study, the effects of temperature on the growth, lipid content, fatty acid composition and biodiesel properties of the marine microalgae Chaetoceros sp. FIKU035, Tetraselmis suecica FIKU032 and Nannochloropsis sp. FIKU036 were investigated. These species were cultured at different temperatures (25, 30, 35 and 40 °C). The results showed that the specific growth rate, biomass and lipid content of all microalgae decreased with increasing temperature. With regards to fatty acids, the presence of saturated fatty acids (SFAs) in T. suecica FIKU032 and Nannochloropsis sp. FIKU036 decreased with increasing temperature, in contrast with polyunsaturated fatty acids (PUFAs). Moreover, Chaetoceros sp. FIKU035 was the only species that could grow at 40 °C. The highest lipid productivity was observed in Chaetoceros sp. FIKU035 when cultivated at 25 °C (66.73 ± 1.34 mg L^?1 day^?1) and 30 °C (61.35 ± 2.89 mg L^?1 day^?1). Moreover, the biodiesel properties (cetane number, cold filter plugging point, kinematic viscosity and density) of the lipids obtained from this species were in accordance with biodiesel standards. This study indicated that Chaetoceros sp. FIKU035 can be considered as a suitable species for biodiesel production in outdoor cultivation.