Electrochemical sensor for guanine using a self-assembled monolayer of 1,8,15,22-tetraaminophthalocyanatonickel(II) on glassy carbon electrode

This article describes the selective determination of guanine (G) using the self-assembled monolayer (SAM) of 1,8,15,22-tetraaminophthalocyanatonickel(II) (4α-Ni(II)TAPc) modified glassy carbon electrode (GCE) in 0.2 M acetate buffer solution (pH 4.0). The SAM of 4α-Ni(II)TAPc was formed on GCE by spontaneous adsorption of 1 mM 4α-Ni(II)TAPc in dimethylformamide (DMF). It shows two pairs of redox waves corresponding to Ni(III)/Ni(II) and Ni(III)Pc(-1)/Ni(III)Pc(-2) in 0.2 M acetate buffer solution. The SAM modified electrode exhibits excellent electrocatalytic activity toward the oxidation of G by enhancing its oxidation current with 150 mV less positive potential shift in contrast to bare GCE. Furthermore, the SAM modified electrode selectively determines G in the presence of high concentration of adenine (A). In differential pulse voltammetry measurements, the oxidation current response of G was increased linearly in the concentration range of 10 to 100 μM, and a detection limit was found to be 3×10(-8)M (signal/noise=3).     

A novel sensor based on electrochemical polymerization of diglycolic acid for determination of acetaminophen

Diglycolic acid (DA) polymer was coated on glassy carbon (GC) electrode by cyclic voltammetry (CV) technique for the first time. The electrochemical performances of the modified electrode were investigated by CV and electrochemical impedance (EIS). The obtained electrode showed an excellent electrocatalytic activity for the oxidation of acetaminophen (ACOP). A couple of well-defined reversible electrochemical redox peaks were observed on the ploy(DA)/GC electrode in ACOP solution. Compared with bare GC electrode, the oxidation peak potential of ACOP on ploy(DA)/GC electrode moved from 0.289 V to 0.220 V. Meanwhile, the oxidation peak current was much higher on the modified electrode than that on the bare GC electrode, indicating DA polymer modified electrode possessed excellent performance for the oxidation of ACOP. This kind of capability of the modified electrode can be enlisted for the highly sensitive and selective determination of ACOP. Under the optimized conditions, a wide linear range from 2 × 10(-8) to 5.0 × 10(-4)M with a correlation coefficient 0.9995 was obtained. The detection limit was 6.7 × 10(-9)M (at the ratio of signal to noise, S/N=3:1). The modified electrode also exhibited very good stability and reproducibility for the detection of ACOP. The established method was applied to the determination of ACOP in samples. An average recovery of 100.1% was achieved. These results indicated that this method was reliable for determining ACOP.     

Effect of divalent cations on the porcine kidney cortex membrane-bound form of dipeptidyl peptidase IV

Dipeptidyl peptidase IV is an ectopeptidase with multiple physiological roles including the degradation of incretins, and a target of therapies for type 2 diabetes mellitus. Divalent cations can inhibit its activity, but there has been little effort to understand how they act. The intact membrane-bound form of porcine kidney dipeptidyl peptidase IV was purified by a simple and fast procedure. The purified enzyme hydrolyzed Gly-Pro-p-nitroanilide with an average V(max) of 1.397±0.003 μmol min(-1) mL(-1), k(cat) of 145.0±1.2 s(-1), K(M) of 0.138±0.005 mM and k(cat)/K(M) of 1050 mM(-1) s(-1). The enzyme was inhibited by bacitracin, tosyl-L-lysine chloromethyl ketone, and by the dipeptidyl peptidase IV family inhibitor L-threo-Ile-thiazolidide (K(i) 70 nM). The enzyme was inhibited by the divalent ions Ca(2+), Co(2+), Cd(2+), Hg(2+) and Zn(2+), following kinetic mechanisms of mixed inhibition, with K(i) values of 2.04×10(-1), 2.28×10(-2), 4.21×10(-4), 8.00×10(-5) and 2.95×10(-5) M, respectively. According to bioinformatic tools, Ca(2+) ions preferentially bound to the β-propeller domain of the porcine enzyme, while Zn(2+) ions to the α-β hydrolase domain; the binding sites were strikingly conserved in the human enzyme and other homologues. The functional characterization indicates that porcine and human homologues have very similar functional properties. Knowledge about the mechanisms of action of divalent cations may facilitate the design of new inhibitors.     

SiO2/SnO2/Sb2O5 microporous ceramic material for immobilization of Meldola's blue: application as an electrochemical sensor for NADH

The mixed oxide SiO(2)/SnO(2), containing 25 wt% of SnO(2), determined by X-ray fluorescence, was prepared by the sol-gel method and the porous matrix obtained was then grafted with Sb (V), resulting the solid designated as (SiSnSb). XPS indicated 0.7% of Sb atoms on the surface. Sb grafted on the surface contains Br?nsted acid centers (SbOH groups) that can immobilize Meldola's blue (MB(+)) cationic dye onto the surface by an ion exchange reaction, resulting the solid designated as (SiSnSb/MB). In the present case a surface concentration of MB(+)=2.5×10(-11) mol cm(2) on the surface was obtained. A homogeneous mixture of the SiSnSb/MB with ultra pure graphite (99.99%) was pressed in disk format and used to fabricate a working electrode that displayed an excellent specific electrocatalytic response to NADH oxidation, with a formal potential of -0.05 V at pH 7.3. The electrochemical properties of the resulting electrode were investigated thoroughly with cyclic voltammetric and chronoamperometry techniques. The proposed sensor showed a good linear response range for NADH concentrations between 8×10(-5) and 9.0×10(-4) mol L(-1), with a detection limit of 1.5×10(-7) mol L(-1). The presence of dopamine and ascorbic acid did not show any interference in the detection of NADH on this modified electrode surface.     

Cobalt(IV) corroles as catalysts for the electroreduction of O2: reactions of heterobimetallic dyads containing a face-to-face linked Fe(III) or Mn(III) porphyrin

A series of heterobinuclear cofacial porphyrin-corrole dyads containing a Co(IV) corrole linked by one of four different spacers in a face-to-face arrangement with an Fe(III) or Mn(III) porphyrin have been examined as catalysts for the electroreduction of O(2) to H(2)O and/or H(2)O(2) when adsorbed on the surface of a graphite electrode in air-saturated aqueous solutions containing 1M HClO(4). The examined compounds are represented as (PCY)M(III)ClCo(IV)Cl where P is a porphyrin dianion, C is a corrole trianion and Y is a biphenylene (B), 9,9-dimethylxanthene (X), dibenzofuran (O) or anthracene (A) spacer. The catalytic behavior of the seven investigated dyads in the two heterobimetallic (PCY)MClCoCl series of catalysts is compared on one hand to what was previously reported for related dyads with a single Co(III) corrole macrocycle linked to a free-base porphyrin with the same set of linking bridges, (PCY)H(2)Co, and on the other hand to dicobalt porphyrin-corrole dyads of the form (PCY)Co(2) which were shown to efficiently electrocatalyze the four electron reduction of O(2) at a graphite electrode in acid media. Comparisons between the four series of porphyrin-corrole dyads, (PCY)Co(2), (PCY)H(2)Co, (PCY)FeClCoCl and (PCY)MnClCoCl, show that in all cases the biscobalt dyads catalyze O(2) electroreduction at potentials more positive by an average 110mV as compared to the related series of compounds containing a Co(III) or Co(IV) corrole macrocycle linked to a free-base metalloporphyrin or a metalloporphyrin with an Fe(III) or Mn(III) central metal ion. The data indicates that the E(1/2) values where electrocatalysis is initiated is related to the initial site of electron transfer, which is the Co(III)/Co(II) porphyrin reduction process in the case of (PCY)Co(2) and the Co(IV)/Co(III) corrole reduction in the case of (PCY)MnClCoCl, (PCY)FeClCoCl and (PCY)H(2)Co. The overall data also suggests that the catalytically active form of the biscobalt dyad in (PCY)Co(2) contains a Co(II) porphyrin and a Co(IV) corrole.     

An integrated microfluidic system for rapid screening of alpha-fetoprotein-specific aptamers

An electrically neutral cobalt complex, Co(Eim)(4)(NCS)(2) (Eim=1-ethylimidazole, NCS=isothiocyanate) was synthesized and its interaction with double-stranded DNA (dsDNA) was comprehensively studied by electrochemical methods on a glassy carbon electrode (GCE). The experimental results revealed that the cobalt complex could interact with dsDNA via a specific groove-binding mode with an affinity constant of 3.6×10(5)M(-1). The surface-based studies showed that Co(Eim)(4)(NCS)(2) could electrochemically accumulate within the immobilized dsDNA layer rather than single-stranded DNA (ssDNA) layer. Based on this fact, the cobalt complex was utilized as an electrochemical hybridization indicator for the detection of oligonucleotides related to CaMV35S promoter gene. The results showed that the developed biosensor presented very low background interference due to the negligible affinity of the Co(Eim)(4)(NCS)(2) complex with ssDNA. The hybridization specificity experiments further indicated that the biosensor could well discriminate the complementary sequence from the base-mismatched and the non-complementary sequences. The complementary target sequence could be quantified over the range from 5.0×10(-9)M to 2.0×10(-6)M with a detection limit of 2.0×10(-10)M.     

Assay of acetylcholinesterase activity by potentiometric monitoring of acetylcholine

An acetylcholine-selective electrode based on a plasticized polymeric membrane has been developed. The electrode exhibited good selectivity for acetylcholine (ACh) over choline and some common ions, low drift, and a fast response to ACh. The response was linear over an ACh concentration range of 1×10(-6) to 1×10(-3) M with a slope of 59.1±0.1 and a detection limit of 1.5×10(-7)±1.2×10(-8) M. The electrode was used to monitor enzymatic ACh hydrolysis catalyzed by acetylcholinesterase (AChE) at different substrate and enzyme concentrations. A kinetic data analysis permitted the determination of the Michaelis-Menten constant of the enzymatic hydrolysis and AChE activity in the range of 2×10(-5) to 3.8×10(-1)U ml(-1).     

DNA immobilization on a polypyrrole nanofiber modified electrode and its interaction with salicylic acid/aspirin

A double-stranded calf thymus DNA (dsDNA) was physisorbed onto a polypyrrole (PPy) nanofiber film that had been electrochemically deposited onto a Pt electrode. The surface morphology of the polymeric film was characterized using scanning electron microscopy (SEM). The electrochemical characteristics of the PPy film and the DNA deposited onto the PPy modified electrode were investigated by cyclic voltammetry (CV), differential pulse voltammetry (DPV), and electrochemical impedance spectroscopy (EIS). Then the interaction of DNA with salicylic acid (SA) and acetylsalicylic acid (ASA), or aspirin, was studied on the electrode surface with DPV. An increase in the DPV current was observed due to the oxidation of guanine, which decreased with the increasing concentrations of the ligands. The interactions of SA and ASA with the DNA follow the saturation isotherm behavior. The binding constants of these interactions were 1.15 × 10⁴ M for SA and 7.46 × 10⁵ M for ASA. The numbers of binding sites of SA and ASA on DNA were approximately 0.8 and 0.6, respectively. The linear dynamic ranges of the sensors were 0.1–2 μM (r² = 0.996) and 0.05–1 mM (r² = 0.996) with limits of detection of 8.62 × 10⁻¹ and 5.24 × 10⁻⁶ μM for SA and ASA, respectively.     

Cobalt(II) Oxidation by the Marine Manganese(II)-Oxidizing Bacillus sp. Strain SG-1

The geochemical cycling of cobalt (Co) has often been considered to be controlled by the scavenging and oxidation of Co(II) on the surface of manganese [Mn(III,IV)] oxides or manganates. Because Mn(II) oxidation in the environment is often catalyzed by bacteria, we have investigated the ability of Mn(II)-oxidizing bacteria to bind and oxidize Co(II) in the absence of Mn(II) to determine whether some Mn(II)-oxidizing bacteria also oxidize Co(II) independently of Mn oxidation. We used the marine Bacillus sp. strain SG-1, which produces mature spores that oxidize Mn(II), apparently due to a protein in their spore coats (R.A. Rosson and K. H. Nealson, J. Bacteriol. 151:1027-1034, 1982; J. P. M. de Vrind et al., Appl. Environ. Microbiol. 52:1096-1100, 1986). A method to measure Co(II) oxidation using radioactive ⁵⁷Co as a tracer and treatments with nonradioactive (cold) Co(II) and ascorbate to discriminate bound Co from oxidized Co was developed. SG-1 spores were found to oxidize Co(II) over a wide range of pH, temperature, and Co(II) concentration. Leucoberbelin blue, a reagent that reacts with Mn(III,IV) oxides forming a blue color, was found to also react with Co(III) oxides and was used to verify the presence of oxidized Co in the absence of added Mn(II). Co(II) oxidation occurred optimally around pH 8 and between 55 and 65°C. SG-1 spores oxidized Co(II) at all Co(II) concentrations tested from the trace levels found in seawater to 100 mM. Co(II) oxidation was found to follow Michaelis-Menten kinetics. An Eadie-Hofstee plot of the data suggests that SG-1 spores have two oxidation systems, a high-affinity-low-rate system (K_m, 3.3 × 10^-8 M; V_max, 1.7 × 10^-15 M · spore^-1 · h^-1) and a low-affinity-high-rate system (K_m, 5.2 × 10^-6 M; V_max, 8.9 × 10^-15 M · spore^-1 · h^-1). SG-1 spores did not oxidize Co(II) in the absence of oxygen, also indicating that oxidation was not due to abiological Co(II) oxidation on the surface of preformed Mn(III,IV) oxides. These results suggest that some microorganisms may directly oxidize Co(II) and such biological activities may exert some control on the behavior of Co in nature. SG-1 spores may also have useful applications in metal removal, recovery, and immobilization processes.     

Rapid and quantitative activation of Chlamydia trachomatis ribonucleotide reductase by hydrogen peroxide

We recently showed that the class Ic ribonucleotide reductase (RNR) from the human pathogen Chlamydia trachomatis ( Ct) uses a Mn (IV)/Fe (III) cofactor in its R2 subunit to initiate catalysis [Jiang, W., Yun, D., Saleh, L., Barr, E. W., Xing, G., Hoffart, L. M., Maslak, M.-A., Krebs, C., and Bollinger, J. M., Jr. (2007) Science 316, 1188-1191]. The Mn (IV) site of the novel cofactor functionally replaces the tyrosyl radical used by conventional class I RNRs to initiate substrate radical production. As a first step in evaluating the hypothesis that the use of the alternative cofactor could make the RNR more robust to reactive oxygen and nitrogen species [RO(N)S] produced by the host's immune system [H?gbom, M., Stenmark, P., Voevodskaya, N., McClarty, G., Gr?slund, A., and Nordlund, P. (2004) Science 305, 245-248], we have examined the reactivities of three stable redox states of the Mn/Fe cluster (Mn (II)/Fe (II), Mn (III)/Fe (III), and Mn (IV)/Fe (III)) toward hydrogen peroxide. Not only is the activity of the Mn (IV)/Fe (III)-R2 intermediate stable to prolonged (>1 h) incubations with as much as 5 mM H 2O 2, but both the fully reduced (Mn (II)/Fe (II)) and one-electron-reduced (Mn (III)/Fe (III)) forms of the protein are also efficiently activated by H 2O 2. The Mn (III)/Fe (III)-R2 species reacts with a second-order rate constant of 8 +/- 1 M (-1) s (-1) to yield the Mn (IV)/Fe (IV)-R2 intermediate previously observed in the reaction of Mn (II)/Fe (II)-R2 with O 2 [Jiang, W., Hoffart, L. M., Krebs, C., and Bollinger, J. M., Jr. (2007) Biochemistry 46, 8709-8716]. As previously observed, the intermediate decays by reduction of the Fe site to the active Mn (IV)/Fe (III)-R2 complex. The reaction of the Mn (II)/Fe (II)-R2 species with H 2O 2 proceeds in three resolved steps: sequential oxidation to Mn (III)/Fe (III)-R2 ( k = 1.7 +/- 0.3 mM (-1) s (-1)) and Mn (IV)/Fe (IV)-R2, followed by decay of the intermediate to the active Mn (IV)/Fe (III)-R2 product. The efficient reaction of both reduced forms with H 2O 2 contrasts with previous observations on the conventional class I RNR from Escherichia coli, which is efficiently converted from the fully reduced (Fe 2 (II/II)) to the "met" (Fe 2 (III/III)) form [Gerez, C., and Fontecave, M. (1992) Biochemistry 31, 780-786] but is then only very inefficiently converted from the met to the active (Fe 2 (III/III)-Y (*)) form [Sahlin, M., Sj?berg, B.-M., Backes, G., Loehr, T., and Sanders-Loehr, J. (1990) Biochem. Biophys. Res. Commun. 167, 813-818].     

Ultra trace analysis of small molecule by label-free impedimetric immunosensor using multilayer modified electrode

A multilayer electrode modified with a self-assembled thiourea monolayer (SATUM) followed by gold nanoparticles (AuNPs), mercaptosuccinic acid (MSA) and antibody was investigated for the detection of ultra trace amount of a small molecule (chloramphenicol) in an impedimetric system. The formation of the antibody-antigen complex at the electrode surface caused the impedance to increase. Under optimum conditions three modified electrodes were compared the SATUM/AuNPs/MSA electrode provided a wide linear range (0.50-10) × 10?1? M, and a very low determination limit of 1.0 × 10?1? M. This determination limit was much lower than the SATUM/AuNPs electrode, 1.0 × 10?1? M, and SATUM electrode, 4.7 × 10?1? M. The modified electrode provided good selectivity for chloramphenicol detection and can be reused up to 45 times with a relative standard deviation of lower than 4%. When applied to determine chloramphenicol in shrimp samples, the results agreed well with those obtained by the high-performance liquid chromatography coupled with a photo diode array detector (P > 0.05). The developed system can be applied to detect other small molecules using appropriate affinity binding pairs.     

Electrochemical immunosensor for casein based on gold nanoparticles and poly(L-Arginine)/multi-walled carbon nanotubes composite film functionalized interface

In this paper, a novel electrochemical immunosensor for the determination of casein based on gold nanoparticles and poly(L-Arginine)/multi-walled carbon nanotubes (P-L-Arg/MWCNTs) composite film was proposed. The P-L-Arg/MWCNTs composite film was used to modify glassy carbon electrode (GCE) to fabricate P-L-Arg/MWCNTs/GCE through electropolymerization of L-Arginine on MWCNTs/GCE. Gold nanoparticles were adsorbed on the modified electrode to immobilize the casein antibody and to construct the immunosensor. The stepwise assembly process of the immunosensor was characterized by cyclic voltammetry and differential pulse voltammetry. Results demonstrated that the peak currents of [Fe(CN)(6)](3-/4-) redox pair decreased due to the formation of antibody-antigen complex on the modified electrode. The optimization of the adsorption time of gold nanoparticles, the pH of supporting electrolyte and the incubation time were investigated in details. Under optimal conditions, the peak currents obtained by DPV decreased linearly with the increasing casein concentrations in the range from 1 × 10(-7) to 1 × 10(-5) g mL(-1) with a linear coefficiency of 0.993. This electrochemical immunoassay has a low detection limit of 5 × 10(-8) g mL(-1) and was successfully applied to the determination of casein in cheese samples.     

Abacavir modulates peroxynitrite-mediated oxidation of ferrous nitrosylated human serum heme-albumin

Human serum albumin (SA) is best known for its extraordinary ligand-binding capacity. Here, kinetics of peroxynitrite-mediated oxidation of SA-heme(II)-NO is reported. Peroxynitrite reacts with SA-heme(II)-NO leading to SA-heme(III) and ()NO by way of the transient SA-heme(III)-NO species. Abacavir facilitates peroxynitrite-mediated oxidation of SA-heme(II)-NO, in the absence and presence of CO2. Values of the second order rate constant for peroxynitrite-mediated oxidation of SA-heme(II)-NO are (6.5+/-0.9) x 10(3) M(-1) s(-1) in the absence of CO2 and abacavir, (1.3+/-0.2) x 10(5) M(-1) s(-1) in the presence of CO2, (2.2+/-0.2) x 10(4) M(-1) s(-1) in the presence of abacavir, and (3.6+/-0.3) x 10(5) M(-1) s(-1) in the presence of both CO2 and abacavir. The value of the first-order rate constant for *NO dissociation from the SA-heme(III)-NO complex (=(1.8+/-0.3) x 10(-1) s(-1)) is CO2- and abacavir-independent, representing the rate-limiting step. Present data represent the first evidence for the allosteric modulation of SA-heme reactivity by heterotropic interaction(s).     

Chitosan-iron oxide nano-composite platform for mismatch-discriminating DNA hybridization for Neisseria gonorrhoeae detection causing sexually transmitted disease

Electrochemically fabricated nano-composite film of chitosan (CH)-iron oxide (Fe(3)O(4)) has been used to detect gonorrhoea, a sexually transmitted disease (STD) via immobilization of biotinylated probe DNA (BDNA) using avidin-biotin coupling for rapid and specific (mismatch-discriminating) DNA hybridization. The presence of Fe(3)O(4) nanoparticles (～18nm) increases the electro-active surface area of the nano-biocomposite that provides desirable environment for loading of DNA with better conformation leading to increased electron transfer kinetics between the medium and electrode. The differential pulse voltammetric (DPV) studies have been conducted using BDNA/avidin/CH-Fe(3)O(4)/ITO electrode owing to the reduction of the methylene blue (MB) indicator and investigate electron transfer between MB moieties and electrode for one and two-bases mismatch. This STD biosensor is found to have a detection limit (1 × 10(-15)M) and a wide dynamic range (from 1 × 10(-16)M to 1 × 10(-6)M) using the complementary target DNA. In addition, the sensing system can be utilized to accurately discriminate complementary sequence from mismatch sequences.     

Electrochemical sensor based on nitrogen doped graphene: simultaneous determination of ascorbic acid, dopamine and uric acid

Nitrogen doped graphene (NG) was prepared by thermally annealing graphite oxide and melamine mixture. After characterization by atomic force microscopy and X-ray photoelectron spectroscopy etc., the electrochemical sensor based on NG was constructed to simultaneously determine small biomolecules such as ascorbic acid (AA), dopamine (DA) and uric acid (UA). Due to its unique structure and properties originating from nitrogen doping, NG shows highly electrocatalytic activity towards the oxidation of AA, DA and UA. The electrochemical sensor shows a wide linear response for AA, DA and UA in the concentration range of 5.0×10(-6) to 1.3×10(-3)M, 5.0×10(-7) to 1.7×10(-4)M and 1.0×10(-7) to 2.0×10(-5)M with detection limit of 2.2×10(-6)M, 2.5×10(-7)M and 4.5×10(-8)M at S/N=3, respectively. These results demonstrate that NG is a promising candidate of advanced electrode material in electrochemical sensing and other electrocatalytic applications.     

Mechanisms of peroxynitrite decomposition catalyzed by FeTMPS, a bioactive sulfonated iron porphyrin

Peroxynitrite is a known cytotoxic agent that plays a role in many pathological conditions. Various peroxynitrite decomposition catalysts and pathways are being explored to develop efficient therapeutic agents that can safely remove peroxynitrite from cells and tissues. Water-soluble porphyrins, such as iron(III) meso-tetra(2,4,6-trimethyl-3,5-disulfonato)porphine chloride (FeTMPS) and iron(III) meso-tetra(N-methyl4-pyridyl)porphine chloride (FeTMPyP), have been shown to react catalytically with peroxynitrite (ONOO-). However, their mechanisms are yet to be fully understood. In this study, we have explored the reactivity of FeTMPS in the catalytic decomposition of peroxynitrite. The mechanism of this complex process has been determined. According to this mechanism, Fe(III)TMPS is oxidized by peroxynitrite to produce oxoFe(lV)TMPS and NO2 (k1 = 1.3 x 10(5) M(-1)(s(-1). The porphyrin is then reduced back to Fe(III)TMPS by nitrite, but this rate (k2 = 1.4 x 10(4) M(-1)s(-1)) is not sufficient to maintain the catalytic process at the observed rate. The overall rate of peroxynitrite decomposition catalysis, kcat, was determined to be 6 x 10(4) M(-1)s(-1), under typical conditions. We have postulated that an additional reduction pathway must exist. Kinetic simulations showed that a reaction of oxoFe(IV)TMPS with NO2 (k3 = 1.7 x 10(7) M((-1)s(-1)) could explain the behavior of this system and account for the fast reduction of oxoFe(IV)TMPS to Fe(III). Using the kinetic simulation analysis, we have also shown that two other rearrangement reactions, involving FeTMPS and peroxynitrite, are plausible pathways for peroxynitrite decay. A "cage-return" reaction between the generated oxoFe(IV)TMPS and NO2 (k8 = 5.4 x 10(4) M(-1)s(-1)), affording Fe(III)TMPS and nitrate, and a reaction between oxoFe(IV)TMPS and peroxynitrite (k7 = 2.4 x 10(4) M(-1)s(-1)) that affords oxoFe(IV)TMPS and nitrate are presented. The mechanism of FeTMPS-catalyzed peroxynitrite decay differs markedly from that of FeTMPyP, providing some insight into the reactivity of metal centers with peroxynitrite and biologically important radicals such as NO2.     

Inactivation of bakers' yeast glucose-6-phosphate dehydrogenase by aluminum

Preincubation of yeast glucose-6-phosphate dehydrogenase (G6PD) with Al(III) produced an inactive enzyme containing 1 mol of Al(III)/mol of enzyme subunit. None of the enzyme-bound Al(III) was dissociated by dialysis against 10 mM Tris-HCl, pH 7.0, containing 0.2 mM EDTA at 4 degrees C for 24 h. Citrate, NADP+, EDTA, or NaF protected the enzyme against the Al(III) inactivation. The Al-(III)-inactivated enzyme, however, was completely reactivated only by citrate and NaF. The dissociation constant for the enzyme-aluminum complex was calculated to be 4 x 10(-6)M with NaF, a known reversible chelator for aluminum. Modification of histidine and lysine residues of the enzyme with diethyl pyrocarbonate and acetylsalicylic acid, respectively, inactivated the enzyme. However, the modified enzyme still bound 1 mol of Al(III)/mol of enzyme subunit. Circular dichroism studies showed that the binding of Al(III) to the enzyme induced a decrease in alpha-helix and beta-sheet and an increase in random coil. Therefore, it is suggested that inactivation of G6PD by Al(III) is due to the conformational change induced by Al(III) binding.     

Modeling the haloperoxidases: reversible oxygen atom transfer between bromide ion and an oxo-Mn(V) porphyrin

The manganese meso-dimethylimidazolium porphyrin complex Mn(III)[TDMImP] reacted with HOBr/OBr(-) to generate the corresponding oxo-Mn(V)[TDMImP] species. The rate of this process accelerated with increasing pH. A forward rate constant, k(for), of 1.65x10(6)M(-1)s(-1) was determined at pH 8. Under these conditions, the oxo-Mn(V) species is short-lived and is transformed into the corresponding oxo-Mn(IV) complex. A first-order rate constant, k(obs), of 0.66 s(-1) was found for this reduction process at pH 8. The mechanism of this reduction process, which was dependent on bromide ion, appeared to proceed via an intermediate Mn(III)-O-Br complex. Thus, both a fast, reversible Mn(III)-O-Br bond heterolysis and a slower homolytic pathway occur in parallel in this system. The reverse oxidation reaction between oxo-Mn(V)[TDMImP] and bromide was investigated as a function of pH. The rate of this oxo-transfer reaction (k(rev)=1.4x10(3)M(-1)s(-1) at pH 8) markedly accelerated as the pH was lowered. The observed first-order dependence of the rate on [H(+)] indicates that the reactive species responsible for bromide oxidation is a protonated oxo-hydroxo complex and the stable species present in solution at high pH is dioxo-Mn(V)[TDMImP], [O=Mn(V)=O](-). The oxo-Mn(V) species retains nearly all of the oxidative driving force of the hypohalite. The equilibrium constant K(equi)=k(for)/k(rev) for the reversible process was determined at three different pH values (K(equi)=1.15x10(3) at pH 8) allowing the measurement of the redox potentials E of oxo-Mn(V)/Mn(III) (E=1.01 V at pH 8). The redox potential for this couple was extrapolated over the entire pH scale using the Nernst relationship and compared to those of the manganese 2- and 4-meso-N-methylpyridinium porphyrin couples oxo-Mn(V)[2-TMPyP]/Mn(III)[2-TMPyP], oxo-Mn(V)[4-TMPyP]/Mn(III)[4-TMPyP], OBr(-)/Br(-) and H(2)O(2)/H(2)O. Notably, the redox potential of oxo-Mn(V)/Mn(III) for the imidazolium porphyrin approaches that of H(2)O(2)/H(2)O at low pH.     

DNA damage and 2'-deoxyguanosine oxidation induced by S(IV) autoxidation catalyzed by copper(II) tetraglycine complexes: synergistic effect of a second metal ion

S(IV) (SO(2),HSO(3)(-)andSO(3)(2-)) autoxidation catalyzed by Cu(II)/tetraglycine complexes in the presence of DNA or 2'-deoxyguanosine (dGuo) resulted in DNA strand breaks and formation of 8-oxo-7,8-dihydro-2'-deoxyguanosine (8-oxodGuo), respectively. Ni(II), Co(II) or Mn(II) (1.0x10(-4)M) complexes had much smaller effects. Cu(II)/tetraglycine (1.0x10(-4)M) in the presence of Ni(II) or Mn(II) (10(-7)-10(-6)M) and S(IV) showed remarkable synergistic effect with these metal ions producing a higher yield of 8-oxodGuo. Oxidation of dGuo and DNA damage were attributed to oxysulfur radicals formed as intermediates in S(IV) autoxidation catalyzed by transition metal ions. SO*(3)(-) and HO* radicals were detected by EPR-spin trapping experiments with DMPO (5,5-dimethyl-1-pyrroline-N-oxide).     

Rescue of the orphan enzyme isoguanine deaminase

Cytosine deaminase (CDA) from Escherichia coli was shown to catalyze the deamination of isoguanine (2-oxoadenine) to xanthine. Isoguanine is an oxidation product of adenine in DNA that is mutagenic to the cell. The isoguanine deaminase activity in E. coli was partially purified by ammonium sulfate fractionation, gel filtration, and anion exchange chromatography. The active protein was identified by peptide mass fingerprint analysis as cytosine deaminase. The kinetic constants for the deamination of isoguanine at pH 7.7 are as follows: k(cat) = 49 s(-1), K(m) = 72 μM, and k(cat)/K(m) = 6.7 × 10(5) M(-1) s(-1). The kinetic constants for the deamination of cytosine are as follows: k(cat) = 45 s(-1), K(m) = 302 μM, and k(cat)/K(m) = 1.5 × 10(5) M(-1) s(-1). Under these reaction conditions, isoguanine is the better substrate for cytosine deaminase. The three-dimensional structure of CDA was determined with isoguanine in the active site.