One-step kinetics-based immunoassay for the highly sensitive detection of C-reactive protein in less than 30 min

This article reveals a rapid sandwich enzyme-linked immunosorbent assay (ELISA) for the highly sensitive detection of human C-reactive protein (CRP) in less than 30 min. It employs a one-step kinetics-based highly simplified and cost-effective sandwich ELISA procedure with minimal process steps. The procedure involves the formation of a sandwich immune complex on capture anti-human CRP antibody-bound Dynabeads in 15 min, followed by two magnet-assisted washings and one enzymatic reaction. The developed sandwich ELISA detects CRP in the dynamic range of 0.3 to 81 ng ml⁻¹ with a limit of detection of 0.4 ng ml⁻¹ and an analytical sensitivity of 0.7 ng ml⁻¹. It detects CRP spiked in diluted human whole blood and serum with high analytical precision, as confirmed by conventional sandwich ELISA. Moreover, the results of the developed ELISA for the determination of CRP in the ethylenediaminetetraacetic acid plasma samples of patients are in good agreement with those obtained by the conventional ELISA. The developed immunoassay has immense potential for the development of rapid and cost-effective in vitro diagnostic kits.     

Human serum albumin interference on plasmon-based immunokinetic assay for antibody screening in model blood sera

The effect of human serum albumin (HSA) on an immunokinetic assay for an antibody to bovine serum albumin has been determined in model serum solutions with HSA concentrations in the range 0 to 450 μM (0-30 mg ml⁻¹). The assay is performed on two plasmon-based detection platforms: a continuous gold surface and a nanoparticle-based array reader. The assay has a minimum detection concentration of 760 ± 160 pM (120 ± 25 ng ml⁻¹) in phosphate-buffered saline, falling to 2.5 ± 0.7 nM (380 ± 100 ng ml⁻¹) in physiological HSA concentration. The concentration of HSA correlates with the refractive index of the solution, and this may be used to calibrate assay response. The addition of the charged chaotrope SCN⁻ in 150 mM concentration improves the reproducibility and consistency of the assay, with a minimum detection concentration of 2.9 ± 0.5 nM (440 ± 80 ng ml⁻¹). The effect of high concentrations of HSA on the immunokinetic assay can be corrected with a measurement of bulk refractive index in a reference channel.     

Accumulation and excretion of morphine by Calliphora stygia, an Australian blow fly species of forensic importance

This study examined the ability of the forensically important blow fly, Calliphora stygia to actively excrete morphine, thereby maintaining a low morphine level within its body when fed on a diet containing morphine at low (7 pmol g⁻¹) and high (17.5 pmol g⁻¹) concentrations. Morphine was accumulated within the bodies of maggots (≈70% within the tissues) at concentrations which were lower than that of the meat (3-24%). The morphine content of the initial developing stages (second and third instar maggots) maintained on the high morphine diet was higher than those on the low morphine diet. Morphine was cleared from the body with negatively exponential kinetics (High morphine group: Morphine (pmol g⁻¹ wet weight) = 8425e^−0.014t. Low morphine group: Morphine (pmol g⁻¹ wet weight) = 2180e^−0.010t). Clearance constants for morphine by animals in both groups were similar and thus both groups had a similar ability to excrete morphine. The Malpighian tubules of maggots were able to actively secrete morphine using a transport mechanism that transports small type II organic cations, such as morphine and quinine. The rate of morphine secretion by the Malpighian tubules could explain the clearance of the drug by the maggots. As the morphine was transported across the Malpighian tubules cells, a significant proportion was metabolised into a compound that is yet to be fully characterised.     

Facile and sensitive detection of protamine by enhanced room-temperature phosphorescence of Mn-doped ZnS quantum dots

Quantum dot (QD) nanohybrids provide an effective route to explore the new properties of materials and are increasingly used as highly valuable sensitive (bio) chemical probes. Interestingly, the room-temperature phosphorescence (RTP) of 3-mercaptopropionic acid (MPA)-capped Mn-doped ZnS QDs could be remarkably enhanced by the addition of protamine. Based on the above finding, a simple, sensitive, and selective method for rapid detection of protamine was successfully designed. With this method, protamine as a cationic peptide interacts electrostatically with MPA-capped Mn-doped ZnS QDs to form MPA-capped Mn-doped ZnS QD/protamine complexes, which leads to the aggregation of QDs and enhances the RTP intensity. Under the optimized conditions, the RTP intensity change was linearly proportional to the concentration of protamine in the range 0.2–3.0 μg ml⁻¹, and the limit of detection was 0.14 μg ml⁻¹. The proposed method was successfully applied to detect protamine in protamine sulfate injection and human serum samples with satisfactory results, and the recovery ranged from 96.5 to 105.6%.     

Voltammetric determination of cefixime in pharmaceuticals and biological fluids

Electroreduction and adsorption of cefixime was studied in phosphate buffer by cyclic voltammetry (CV), differential pulse cathodic adsorptive stripping voltammetry (DPCAdSV), and square-wave cathodic adsorptive stripping voltammetry (SWCAdSV) at hanging mercury drop electrode (HMDE). These fully validated sensitive and reproducible cathodic adsorptive stripping voltammetric procedures were applied for the trace determination of the bulk drug in pharmaceutical formulations and in human urine. The optimal experimental parameters were as follows: accumulation potential = −0.1 V (vs. Ag/AgCl, 3 M KCl), accumulation time = 50 s, frequency = 140 Hz, pulse amplitude = 0.07 V, and scan increment = 10 mV in phosphate buffer (pH 2.6). The first peak current showed a linear dependence with the drug concentration over the range of 50 ng ml⁻¹ to 25.6 μg ml⁻¹. The achieved limit of detection and limit of quantitation were 3.99 and 13.3 ng ml⁻¹ by SWCAdSV and 7.98 and 26.6 ng ml⁻¹ by DPCAdSV, respectively. The procedure was applied to assay the drug in tablets. Applicability was also tested in urine samples. Peak current was linear with the drug concentration in the range of 1 to 60 μg ml⁻¹ of the urine, and minimum detectability was found to be 12.6 ng ml⁻¹ by SWCAdSV and 58.4 ng ml⁻¹ by DPCAdSV.     

Detection of Bacillus thuringiensis Cry1Ab protein based on surface plasmon resonance immunosensor

Two novel surface plasmon resonance immunosensors were fabricated for detection of the Bacillus thuringiensis Cry1Ab protein and to demonstrate their performance in analyzing Cry1Ab protein in crop samples. Sensor 2 was modified by 1,6-hexanedithiol, Au/Ag alloy nanoparticles, 3-mercaptopropionic acid, and protein A (or not [sensor 1]), with Cry1Ab monoclonal antibody. As a result, both of the immunosensors exhibited satisfactory linear responses in the Cry1Ab protein concentration ranges of 10 to 500 ng ml⁻¹ and 8 to 1000 ng ml⁻¹, and the detection limits were 5.0 and 4.8 ng ml⁻¹, respectively. The immunosensors possessed good specificity and acceptable reproducibility. In addition, crop samples could be analyzed after a simple treatment. The transgenic crops could be easily identified from the conventional ones by the two immunosensors.     

A liquid chromatography method for quantifying caffeine dissolution from pharmaceutical formulations into colloidal,fat-rich media

A simple and rapid high-performance liquid-chromatography method is presented that permits quantification of caffeine in colloidal fat emulsions proposed as new ‘biorelevant’ dissolution media (Intralipid™ and various milks). Using a mobile phase of 0.1 M sodium acetate (pH 4.0) and acetonitrile (89.5:10.5, v/v) at 1 ml min⁻¹, the drug and internal standard (7-β-hydroxyethyltheophylline) were eluted within 8 min. Caffeine extraction was undertaken by protein precipitation in ice-cold 12% (w/v) trichloroacetic acid and centrifugation at 10,000 rpm for 15 min. This simple extraction method generated caffeine recovery values (corrected for % fat content) of 75.4 ± 1.4–100.6 ± 5.5%. The limit of detection was within the range 0.25–0.4 μg ml⁻¹ and linearity was demonstrated in each medium up to 125 μg ml⁻¹. Precision was <11.5% RSD and intra- and inter-day accuracy was 93.4–109.3%. The validated method was applied to in vitro USP dissolution tests in milk which compared the kinetics of caffeine release from (i) extended release matrices containing hydroxypropyl methylcellulose (HPMC) and (ii) an immediate release commercial analgesic tablet. Good reproducibility was obtained in both extended and immediate release dissolution tests. The method provides high-throughput quantification of this common drug in fat emulsions used as biorelevant dissolution media.     

γ-Cyclodextrin–polyurethane copolymer adsorbent for selective removal of endotoxin from DNA solution

Copolymer particles for removal of endotoxins (lipopolysaccharides, LPSs) were prepared by suspension copolymerization of γ-cyclodextrin (CyD) and 1,6-hexamethylenediisocyanate. The LPS-removing activity of the copolymer particles was compared with that of poly(ε-lysine)-immobilized Cellufine (cationic adsorbent) or polystyrene particles (hydrophobic adsorbent) by a batch method. When DNA was present in solution with LPSs under physiological conditions (pH 6.0, ionic strength of μ = 0.05–0.8), LPS-removing activity of the cationic or hydrophobic adsorbent was unsatisfactory because both the DNA and the LPSs were adsorbed onto each adsorbent. By contrast, the copolymer particles with γ-CyD cavity (CyD content: 14–20 mol%) could selectively remove LPSs from a DNA solution (50 μg ml⁻¹, pH 6.0, and μ = 0.05–0.2) containing LPSs (15 EU ml⁻¹) without the adsorption of DNA. The residual concentration of LPSs in the treated DNA solution was below 0.1 EU ml⁻¹, and the recovery of DNA was 99%.     

Determination of 17β-oestradiol by fluorescence immunoassay with streptavidin-conjugated quantum dots as label

A sensitive and selective method for the determination of 17β-oestradiol by fluorescence immunoassay (FIA) was established on the basis of quantum dots (QDs) as label. The complex of biotin-labelled anti-rabbit IgG and strepavidin conjugated by quantum dots (QD-SA) was regarded as a probe in this system and the strepavidin-biotin system as signal amplification system. After optimising the conditions of the immunoreaction, such as the concentration of the reagent and the pH of the buffer solution, the linear range and the limit of detection of 17β-oestradiol were 0.01-10,000 ng ml⁻¹ and 0.00542 ng ml⁻¹, respectively. This method was applied to determine oestradiol in water samples, with the percent recoveries in the range of 86-113%.     

Assessment of olive-mill wastewater as a growth medium for lipase production by Candida cylindracea in bench-top reactor

Olive-mill wastewater (OMW) was investigated for its suitability to serve as a medium for lipase production by Candida cylindracea NRRL Y-17506. The OMW that best supported enzyme production was characterized by low COD and low total sugars content. In shake flask batch cultures, OMW supplementation with 2.4 g l⁻¹ NH₄Cl and 3 g l⁻¹ olive oil led to an enzyme activity of about 10 U ml⁻¹. The addition of glucose or malt extract and supplements containing organic N (e.g., peptone, yeast extract) either depressed or did not affect the enzyme production. Further experiments were then performed in a 3-l stirred tank reactor to assess the impact of medium pH and stirring speed on the yeast enzyme activity. The lipase activity was low (1.8 U ml⁻¹) when the pH was held constant at 6.5, significantly increased (18.7 U ml⁻¹) with uncontrolled pH and was maximum (20.4 U ml⁻¹) when the pH was let free to vary below 6.5. A stirring regime, that varied depending on the dissolved oxygen concentration in the medium, both prevented the occurrence of anoxic conditions during the exponential growth phase and enabled good lipase production (i.e., 21.6 U ml⁻¹) and mean volumetric productivity (i.e., 123.5 U l⁻¹ h⁻¹).     

Screening of boldenone and methylboldenone in bovine urine using disposable electrochemical immunosensors

Electrochemical based immunosensors for the detection of boldenone and methylboldenone in bovine urine were described in this paper. The immunosensors were fabricated by immobilizing boldenone-bovine serum albumin conjugate on the surface of screen-printed electrodes (SPEs), and followed by the competition between the free analyte and coating conjugate with corresponding antibodies. The use of anti-species IgG-horseradish peroxidase conjugate determined the degree of competition. The electrochemical technique chosen was chronoamperometry, performed at a potential of +100 mV whereby the product of the catalysis of 3,3′,5,5′-tetramethylbenzidine undergoes reduction produced by the enzyme label. The limits of detection of assay were 30.9 ± 4.3 pg ml⁻¹ for boldenone and 120.2 ± 8.2 pg ml⁻¹ for methylboldenone, respectively. Results of repeated analysis of each androgen carried out using three different batches of electrodes indicate suitable repeatability (EC₅₀ = 1.0 ± 0.3 ng ml⁻¹ (n = 3, N = 3), R² = 0.969, R.S.D. = 9.6% for boldenone and 1.5 ± 0.3 ng ml⁻¹, 0.971, 10.5% for methylboldenone, respectively). Urine samples were determined directly after a single dilution step, omitting extraction and hydrolysis. This method offers the advantage to pick up both boldenone and its major metabolites in an efficient manner due to the high cross-reactivity pattern of α-boldenone with this antibody. The concentration of methylboldenone in urine detected by developed methods does indicate methylboldenone administration to heifers. Gas chromatography coupled to mass spectrometry analysis was performed to quantitate the individual metabolites present in urine samples, and results were validated with both ELISA and immunosensor data.     

Primary hemocyte culture of Penaeus monodon as an in vitro model for white spot syndrome virus titration, viral and immune related gene expression and cytotoxicity assays

Immortal cell lines have not yet been reported from Penaeus monodon, which delimits the prospects of investigating the associated viral pathogens especially white spot syndrome virus (WSSV). In this context, a method of developing primary hemocyte culture from this crustacean has been standardized by employing modified double strength Leibovitz-15 (L-15) growth medium supplemented with 2% glucose, MEM vitamins (1×), tryptose phosphate broth (2.95 g l⁻¹), 20% FBS, N-phenylthiourea (0.2 mM), 0.06 μg ml⁻¹ chloramphenicol, 100 μg ml⁻¹ streptomycin and 100 IU ml⁻¹ penicillin and hemolymph drawn from shrimp grown under a bio-secured recirculating aquaculture system (RAS). In this medium the hemocytes remained viable up to 8 days. 5-Bromo-2′-deoxyuridine (BrdU) labeling assay revealed its incorporation in 22 ± 7% of cells at 24 h. Susceptibility of the cells to WSSV was confirmed by immunofluoresence assay using a monoclonal antibody against 28 kDa envelope protein of WSSV. A convenient method for determining virus titer as MTT₅₀/ml was standardized employing the primary hemocyte culture. Expression of viral genes and cellular immune genes were also investigated. The cell culture could be demonstrated for determining toxicity of a management chemical (benzalkonium chloride) by determining its IC₅₀. The primary hemocyte culture could serve as a model for WSSV titration and viral and cellular immune related gene expression and also for investigations on cytotoxicity of aquaculture drugs and chemicals.     

Interferences of suspended clay fraction in protein quantitation by several determination methods

Seven current methods of protein quantitation, Bradford (standard, micro, and 590/450 nm ratio), Lowry, bicinchoninic acid (BCA), UV spectrophotometry at 280 nm, and Quant-iT fluorescence-based determination, were compared with regard to their susceptibility to interferences due to the presence of suspended and not easily detectable clay particles. Bovine serum albumin (BSA) and Na-Wyoming montmorillonite were selected as model protein and reference clay, respectively. Protein-clay suspension mixtures were freshly prepared for each assay to simulate supernatants not completely centrifuged in batch sorption/kinetic experiments. Seven fixed increasing levels of clay (0.0, 0.00725, 0.0145, 0.029, 0.058, 0.145, 0.435 mg ml⁻¹) were mixed with different levels of BSA in an appropriate range for each assay. To ascertain the interfering effect of different levels of clay, the theoretical concentrations of BSA were plotted against the estimated BSA concentrations of the samples, as obtained from the calibration curve of each method. A correct quantitation of the BSA concentration not influenced by clay would be described by a regression line with slope (b) not significantly different from 1 and an intercept (a) not significantly different from zero. At the lowest clay levels (0.00725 mg ml⁻¹) a significant interference was evident for Bradford micro, Bradford 590/450, UV, and fluorescence. The three methods (Bradford standard, Lowry, and BCA) that seemed to show the better performances in the presence of clay after this first screening step also underwent an ANCOVA analysis, with the measured BSA concentrations as dependent variable and the clay concentrations as covariate. The Bradford standard and BCA methods were affected by a clay-dependent interference on BSA quantitation. The Lowry assay was the only method that gave correct estimates of BSA concentrations in the presence of any of the clay levels tested.     

Electrochemical biosensor based on base-stacking-dependent DNA hybridization assay for protein detection

An antibody-based electrochemical biosensing platform has been developed and used for the detection of protein. In the presence of the target, an antibody pair binds to the protein simultaneously, which causes two oligo-DNAs conjugated with the antibody pair to hybridize to each other and become a big “stem–loop” structure. Subsequently, the longer oligo-DNA of the stem, with a methylene blue (MB) label at the terminal, hybridizes stably with capture DNA owing to the enhancement of base stacking. The strong redox current signal of MB is used for protein quantification. Using α-fetoprotein (AFP) as a model, the proposed method could detect AFP at a concentration as low as 2 pg ml⁻¹ with a dynamic range of 4 orders of magnitude, which approaches traditional assays such as enzyme-linked immunosorbent assay.     

Synergistic production of L-arabinose from arabinan by the combined use of thermostable endo- and exo-arabinanases from Caldicellulosiruptor saccharolyticus

The optimum conditions for the production of l-arabinose from debranched arabinan were determined to be pH 6.5, 75 °C, 20 g l⁻¹ debranched arabinan, 42 U ml⁻¹ endo-1,5-α-l-arabinanase, and 14 U ml⁻¹ α-l-arabinofuranosidase from Caldicellulosiruptor saccharolyticus and the conditions for sugar beet arabinan were pH 6.0, 75 °C, 20 g l⁻¹ sugar beet arabinan, 3 U ml⁻¹ endo-1,5-α-l-arabinanase, and 24 U ml⁻¹ α-l-arabinofuranosidase. Under the optimum conditions, 16 g l⁻¹l-arabinose was obtained from 20 g l⁻¹ debranched arabinan or sugar beet arabinan after 120 min, with a hydrolysis yield of 80% and a productivity of 8 g l⁻¹ h⁻¹. This is the first reported trial for the production of l-arabinose from the hemicellulose arabinan by the combined use of endo- and exo-arabinanases.     

Enhanced electrochemiluminescence from luminol at carboxyl graphene for detection of α-fetoprotein

In this study, a novel sensitive electrochemiluminescence (ECL) immunosensor was constructed by carboxyl graphene (GR) for enhancing luminol–O₂ system emission. Here, carboxyl GR was used to enhance the ECL intensity of luminol that had excellent electron transfer ability and good solubility. The sensing platform was constructed by depositing carboxyl GR on electrodes and immobilizing antibodies on the surface of carboxyl GR through amidation. The specific immunoreaction between α-fetoprotein (AFP) and antibodies resulted in a decrease of ECL intensity, and the intensity decreased linearly with AFP concentrations in the range of 5 pg ml⁻¹ to 14 ng ml⁻¹ with a detection limit of 2.0 pg ml⁻¹. The proposed immunosensor exhibits high specificity, good reproducibility, and longtime stability. It may become a promising technique for protein detection.     

Whole serum BSA antibody screening using a label-free biophotonic nanoparticle array

Bovine serum albumin antibodies (aBSA) have been screened from whole leporine anti serum on a biophotonic array. The array was initially printed with seed gold nanoparticles into a 96-spot configuration, and 130-nm gold nanoparticles were synthesised in situ on the surface of each spot. The gold nanoparticle surface was then functionalized with the proteins bovine serum albumin (BSA), fibrinogen, and immunoglobulin G (IgG) and with the amino acid glycine. The concentration of aBSA in the whole serum was determined using a kinetic analysis of the time-dependent light scattering from the nanoparticles. The aBSA-BSA kinetic parameters derived from the array are k_a = (1.3 ± 0.3) × 10⁵ M⁻¹ s⁻¹, k_d = (4 ± 2) × 10⁻⁴ s⁻¹, and K_D = 3 nM, which compare favorably with those from continuous gold surfaces. The ultimate sensitivity of the array reader to the bulk refractive index (RI) is 1 × 10⁻⁴ refractive index units (RIU), corresponding to 1 μg ml⁻¹ for aBSA. The nanoparticles appear to be more sensitive than the continuous gold surface to the aBSA binding event from whole serum, and this is interpreted in terms of the difference in RI contrast in the plasmon fields.     

Effects of the methane-inhibitors nitrate,nitroethane, lauric acid,Lauricidin and the Hawaiian marine algae Chaetoceros on ruminal fermentation in vitro

The effects of several methane-inhibitors on rumen fermentation were compared during three 24 h consecutive batch cultures of ruminal microbes in the presence of nonlimiting amounts of hydrogen. After the initial incubation series, methane production was reduced greater than 92% from that of non-treated controls (25.8 ± 8.1 μmol ml⁻¹ incubation fluid) in cultures treated with nitroethane, sodium laurate, Lauricidin^® or a finely-ground product of the marine algae, Chaetoceros (added at 1, 5, 5 and 10 mg ml⁻¹, respectively) but not in cultures treated with sodium nitrate (1 mg m1⁻¹). Methane production during two successive incubations was reduced greater than 98% from controls (22.5 ± 3.2 and 23.5 ± 7.9 μmol ml⁻¹, respectively) by all treatments. Reductions in amounts of volatile fatty acids and ammonia produced and amounts of hexose fermented, when observed, were most severe in sodium laurate-treated cultures. These results demonstrate that all tested compounds inhibited ruminal methane production in our in vitro system but their effects on fermentation differed.     

A biotin-hydrogel-coated quartz crystal microbalance biosensor and applications in immunoassay and peptide-displaying cell detection

A biotin-coated quartz crystal microbalance (QCM) chip was prepared by dip-coating a long-chain alkanethiol-modified crystal with precoupled dextran-biotin hydrogels. The resulting biotin chip was used to affinity-immobilize streptavidin (SAv) and was then further employed for various biosensor assays. First, the SAv chip allowed efficient on-line binding of biotinylated bovine serum albumin (bBSA), followed by a sensitive and specific response toward anti-bovine serum albumin (BSA) antibodies. Three consecutive immunoassays were reproducibly demonstrated with a single chip. The apparent binding kinetics with k_on = 5.9 μM⁻¹ h⁻¹, k_off = 10.1 h⁻¹, and K_D = 1.71 μM was readily resolved by fitting the real-time sensorgrams. Second, the capability of the SAv chip to selectively recognize recombinant Escherichia coli with flagella displaying an artificial SAv binding peptide, Strep-tag II, was demonstrated by QCM analysis and verified by scanning transmission electron microscope (STEM) image analysis with biotin-coated gold nanoparticles as the label. Finally, the affinity of the cell-displayed Strep-tag II peptide to surface-coated SAv, K_D = 6.8 × 10⁸ CFU/ml, was resolved on-line using equilibrium binding kinetics by QCM. This study presents an easy, economical, and reliable method of preparing high-performance SAv-coated biotin chips with potential for application in real-time repetitive immunoassays, on-line binding kinetics studies, and high-affinity peptide screening.     

N-terminal fragment of the anti-angiogenic human endostatin binds copper(II) with very high affinity

A histidine-rich peptide HSHRDFQPVLHL-NH₂ (L), identical with the N-terminal fragment of the anti-angiogenic human endostatin has been synthesized. Endostatin is a recently identified broad spectrum angiogenesis inhibitor, which inhibits 65 different tumor types. The N-terminal 25-mer peptide fragment of human endostatin has the same antitumor effect as the entire protein. The zinc(II) binding is crucial for the antitumor effect in both cases. Our peptide may provide all critical interactions for zinc(II) binding present in the N-terminal 25-mer peptide fragment. In addition, the N-terminus of human endostatin has a supposedly high affinity binding site for copper(II), similar to human serum albumin. Since copper(II) is intimately involved in angiogenesis, this may have biological relevance.In order to determine the metal binding properties of the N-terminal fragment of endostatin, we performed equilibrium, UV-visible (UV-vis), CD, EPR and NMR studies on the zinc(II) and copper(II) complexes of L. In the presence of zinc(II) the formation of a stable {NH₂, 3N_im, COO⁻} coordinated complex was detected in the neutral pH-range. This coordination mode is probably identical to that present in the zinc(II) complex of the above mentioned N-terminal 25-mer peptide fragment of human endostatin. Moreover, L has extremely high copper(II) binding affinity, close to those of copper-containing metalloenzymes, and forms albumin-like {NH₂, N⁻, N⁻, N_im} coordinated copper(II) complex in the neutral pH-range, which may suggest that copper(II) binding is involved in the biological activity of endostatin.