Fast‐Charging and Ultrahigh‐Capacity Lithium Metal Anode Enabled by Surface Alloying

Li metal anodes are going through a great revival but they still encounter grand challenges. One often neglected issue is that most reported Li metal anodes are only cyclable under relatively low current density (<5 mA cm^?2) and small areal capacity (<5 mAh cm^?2), which essentially limits their high‐power applications and results in ineffective Li utilization (<1%). Herein, it is reported that surface alloyed Li metal anodes can enable reversible cycling with ultrafast rate and ultralarge areal capacity. Low‐cost Si wafers are used and are chemically etched down to 20–30 µm membranes. Simply laminating a Si membrane onto Li foil results in the formation of Li_xSi alloy film fused onto Li metal with mechanical robustness and high Li‐ion conductivity. Symmetric cell measurements show that the surface alloyed Li anode has excellent cycling stability, even under high current density up to 25 mA cm^?2 and unprecedented areal capacity up to 100 mAh cm^?2. Furthermore, the surface alloyed Li anode is paired with amorphous MoS₃ cathode and achieves remarkable full‐cell performance.     

High Polarity Poly(vinylidene difluoride) Thin Coating for Dendrite‐Free and High‐Performance Lithium Metal Anodes

The high‐polarity β‐phase poly(vinylidene difluoride) (β‐PVDF), which has all trans conformation with F and H atoms located on the opposite sides of the polymer backbone, is demonstrated to be a promising artificial solid‐electrolyte interphase coating on both Cu and Li metal anodes for dendrite‐free Li deposition/stripping and enhanced cycling performance. A thin (≈4 µm) β‐PVDF coating on Cu enables uniform Li deposition/stripping at high current densities up to 5 mA cm^?2, Li‐plating capacity loadings of up to 4 mAh cm^?2, and excellent cycling stability over hundreds of cycles under practical conditions (1 mA cm^?2 with 2 mAh cm^?2). Full cells containing an LiFePO₄ cathode and an anode of either β‐PVDF coated Cu or Li also exhibit excellent cycling stability. The profound effects of the high‐polarity PVDF coating on dendrite suppression are attributed to the electronegative F‐rich interface that favors layer‐by‐layer Li deposition. This study offers a new strategy for the development of dendrite‐free metal anode technology.     

Electrokinetic Phenomena Enhanced Lithium‐Ion Transport in Leaky Film for Stable Lithium Metal Anodes

The application of lithium (Li) metal anodes in Li metal batteries has been hindered by growth of Li dendrites, which lead to short cycling life. Here a Li‐ion‐affinity leaky film as a protection layer is reported to promote a dendrite‐free Li metal anode. The leaky film induces electrokinetic phenomena to enhance Li‐ion transport, leading to a reduced Li‐ion concentration polarization and homogeneous Li‐ion distribution. As a result, the dendrite‐free Li metal anode during Li plating/stripping is demonstrated even at an extremely high deposition capacity (6 mAh cm^?2) and current density (40 mA cm^?2) with improved Coulombic efficiencies. A full cell battery with the leaky‐film protected Li metal as the anode and high‐areal‐capacity LiNi_0.8Co_0.1Mn_0.1O₂ (NCM‐811) (≈4.2 mAh cm^?2) or LiFePO₄ (≈3.8 mAh cm^?2) as the cathode shows improved cycling stability and capacity retention, even at lean electrolyte conditions.     

In Situ Generation of Artificial Solid‐Electrolyte Interphases on 3D Conducting Scaffolds for High‐Performance Lithium‐Metal Anodes

Rational structure design of the current collector along with further engineering of the solid‐electrolyte interphases (SEI) layer is one of the most promising strategies to achieve uniform Li deposition and inhibit uncontrolled growth of Li dendrites. Here, a Li₂S layer as an artificial SEI with high compositional uniformity and high lithium ion conductivity is in situ generated on the surface of the 3D porous Cu current collector to regulate homogeneous Li plating/stripping. Both simulations and experiments demonstrate that the Li₂S protective layer can passivate the porous Cu skeleton and balance the transport rate of lithium ions and electrons, thereby alleviating the agglomerated Li deposition at the top of the electrode or at the defect area of the SEI layer. As a result, the modified current collector exhibits long‐term cycling of 500 cycles at 1 mA cm^?2 and stable electrodeposition capabilities of 4 mAh cm^?2 at an ultrahigh current density of 4 mA cm^?2. Furthermore, full batteries (LiFePO₄ as cathode) paired with this designed 3D anode with only ≈200% extra lithium show superior stability and rate performance than the batteries paired with lithium foil (≈3000% extra lithium). These explorations provide new strategies for developing high‐performance Li metal anodes.     

Cu3P Binary Phosphide: Synthesis via a Wet Mechanochemical Method and Electrochemical Behavior as Negative Electrode Material for Lithium‐Ion Batteries

Mechanochemical synthesis of Cu₃P in the presence of n‐dodecane results in a material with a secondary particle size distribution of 10 μm, secondary particles which consist of homogeneously agglomerated 20 nm primary particles. The electrochemical performance of Cu₃P with lithium is influenced by the reaction depth, in other words by the lower potential cut‐off. During the electrochemical reaction, the displacement of copper by lithium from the Cu₃P structure until the formation of Li₃P and Cu deteriorates the capacity retention. Improved performance was obtained when the charge potential was limited to 0.50 V (vs. Li/Li⁺) and the formation of the Li_xCu_3‐xP phase (0 ≤ × ≤ 2). In this case, when the potential is limited to 0.5 V, the capacity is stable for more than 50 cycles. Acceptable electrochemical performances in Li‐ion cells within the voltage range 0.50–2.0 V (vs. Li/Li⁺) were shown when Cu₃P was used as an anode and Li_1.2(Ni_0.13Mn_0.54Co_0.13)O₂ and LiNi_0.5Mn_1.5O₄ as positive electrode materials.     

Grafting Benzenediazonium Tetrafluoroborate onto LiNixCoyMnzO2 Materials Achieves Subzero‐Temperature High‐Capacity Lithium‐Ion Storage via a Diazonium Soft‐Chemistry Method

Subzero‐temperature Li‐ion batteries (LIBs) are highly important for specific energy storage applications. Although the nickel‐rich layered lithium transition metal oxides(LiNi_xCo_yMn_zO₂) (LNCM) (x > 0.5, x + y +z = 1) are promising cathode materials for LIBs, their very slow Li‐ion diffusion is a main hurdle on the way to achieve high‐performance subzero‐temperature LIBs. Here, a class of low‐temperature organic/inorganic hybrid cathode materials for LIBs, prepared by grafting a conducting polymer coating on the surface of 3 µm sized LiNi_0.6Co_0.2Mn_0.2O₂ (LNCM‐3) material particles via a greener diazonium soft‐chemistry method is reported. Specifically, LNCM‐3 particles are uniformly coated with a thin polyphenylene film via the spontaneous reaction between LNCM‐3 and C₆H₅N₂⁺BF₄^?. Compared with the uncoated one, the polyphenylene‐coated LNCM‐3 (polyphenylene/LNCM‐3) has shown much improved low‐temperature discharge capacity (≈148 mAh g^?1 at 0.1 C, ?20 °C), outstanding rate capability (≈105 mAh g^?1 at 1 C, ?20 °C), and superior low‐temperature long‐term cycling stability (capacity retention is up to 90% at 0.5 C over 1150 cycles). The low‐temperature performance of polyphenylene/LNCM‐3 is the best among the reported state‐of‐the art cathode materials for LIBs. The present strategy opens up a new avenue to construct advanced cathode materials for wider range applications.     

Synthesis and Characterization of High‐Energy,High‐Power Spinel‐Layered Composite Cathode Materials for Lithium‐Ion Batteries

Spinel‐layered composites, where a high‐voltage spinel is incorporated in a layered lithium‐rich (Li‐rich) cathode material with a nominal composition x{0.6Li₂MnO₃ · 0.4[LiCo_0.333Mn_0.333Ni_0.333]O₂} · (1 – x) Li[Ni_0.5Mn_1.5]O₄ (x = 0, 0.3, 0.5, 0.7, 1) are synthesized via a hydroxide assisted coprecipitation route to generate high‐energy, high‐power cathode materials for Li‐ion batteries. X‐ray diffraction patterns and the cyclic voltammetry investigations confirm the presence of both the parent components in the composites. The electrochemical investigations performed within a wide potential window show an increased structural stability of the spinel component when incorporated into the composite environment. All the composite materials exhibit initial discharge capacities >200 mAh g^–1. The compositions with x = 0.5 and 0.7 show excellent cycling stability among the investigated materials. Moreover, the first cycle Coulombic efficiency achieve a dramatic improvement with the incorporation of the spinel component. More notably, the composite materials with increased spinel component exhibit superior rate capability compared with the parent Li‐rich material especially together with the highest capacity retention for x = 0.5 composition, making this as the optimal high‐energy high‐power material. The mechanisms involved in the symbiotic relationship of the spinel and layered Li‐rich components in the above composites are discussed.     

Ultrathin,Flexible Polymer Electrolyte for Cost‐Effective Fabrication of All‐Solid‐State Lithium Metal Batteries

All‐solid‐state batteries are promising candidates for the next‐generation safer batteries. However, a number of obstacles have limited the practical application of all‐solid‐state Li batteries (ASSLBs), such as moderate ionic conductivity at room temperature. Here, unlike most of the previous approaches, superior performances of ASSLBs are achieved by greatly reducing the thickness of the solid‐state electrolyte (SSE), where ionic conductivity is no longer a limiting factor. The ultrathin SSE (7.5 µm) is developed by integrating the low‐cost polyethylene separator with polyethylene oxide (PEO)/Li‐salt (PPL). The ultrathin PPL shortens Li⁺ diffusion time and distance within the electrolyte, and provides sufficient Li⁺ conductance for batteries to operate at room temperature. The robust yet flexible polyethylene offers mechanical support for the soft PEO/Li‐salt, effectively preventing short‐circuits even under mechanical deformation. Various ASSLBs with PPL electrolyte show superior electrochemical performance. An initial capacity of 135 mAh g^?1 at room temperature and the high‐rate capacity up to 10 C at 60 °C can be achieved in LiFePO₄/PPL/Li batteries. The high‐energy‐density sulfur cathode and MoS₂ anode employing PPL electrolyte also realize remarkable performance. Moreover, the ASSLB can be assembled by a facile process, which can be easily scaled up to mass production.     

Polysulfide‐Shuttle Control in Lithium‐Sulfur Batteries with a Chemically/Electrochemically Compatible NaSICON‐Type Solid Electrolyte

A NaSICON‐type Li⁺‐ion conductive membrane with a formula of Li_{1+ x} Y _x Zr_{2? x} (PO₄)₃ (LYZP) (x = 0–0.15) has been explored as a solid‐electrolyte/separator to suppress polysulfide‐crossover in lithium‐sulfur (Li‐S) batteries. The LYZP membrane with a reasonable Li⁺‐ion conductivity shows both favorable chemical compatibility with the lithium polysulfide species and exhibits good electrochemical stability under the operating conditions of the Li‐S batteries. Through an integration of the LYZP solid electrolyte with the liquid electrolyte, the hybrid Li‐S batteries show greatly enhanced cyclability in contrast to the conventional Li‐S batteries with the porous polymer (e.g., Celgard) separator. At a rate of C/5, the hybrid Li ||LYZP|| Li₂S₆ batteries developed in this study (with a Li‐metal anode, a liquid/LYZP hybrid electrolyte, and a dissolved lithium polysulfide cathode) delivers an initial discharge capacity of ≈1000 mA h g^?1 (based on the active sulfur material) and retains ≈90% of the initial capacity after 150 cycles with a low capacity fade‐rate of <0.07% per cycle.     

Ultrafine Copper Nanopalm Tree‐Like Framework Decorated with Iron Oxide for Li‐Ion Battery Anodes with Exceptional Rate Capability and Cycling Stability

Ultrafine copper nanopalm tree‐like frameworks conformally decorated with iron oxide (Cu NPF@Fe₂O₃) are prepared by a facile electrodeposition method utilizing bromine ions as unique anisotropic growth catalysts. The formation mechanism and control over Cu growth are comprehensively investigated under various conditions to provide a guideline for fabricating a Cu nanoarchitecture via electrochemical methods. The optimized Cu NPFs exhibit ultrathin (<90 nm) and elongated (2–50 µm) branches with well‐interconnected and entangled features, which result in highly desirable attributes such as a large specific surface area (≈6.97 m² g^?1), free transfer pathway for Li⁺, and high electrical conductivity. The structural advantages of Cu NPF@Fe₂O₃ enhance the electrochemical kinetics, providing large reactivity, fast Li⁺/electron transfer, and structural stability during cycling, that lead to superior electrochemical Li storage performance. The resulting Cu NPF@Fe₂O₃ demonstrates a high specific capacity (919.5 mAh g^–1 at 0.1 C), long‐term stability (801.1 mAh g^–1 at 2 C, ≈120% retention after 500 cycles), and outstanding rate capability (630 mAh g^–1 at 10 C).     

Low‐Cost Hollow Mesoporous Polymer Spheres and All‐Solid‐State Lithium,Sodium Batteries

A practical, low‐cost synthesis of hollow mesoporous organic polymer (HMOP) spheres is reported. The electrochemical properties of Li⁺/Na⁺‐electrolyte membranes with these spheres substituting for oxide filler particles in poly(ethylene oxide) (PEO)‐filler composite are explored. The electrolyte membranes are mechanically robust, thermally stable to over 250 °C, and block dendrites from a metallic‐lithium/sodium anode. The Li⁺/Na⁺ transfer impedance across the lithium/sodium–electrolyte interface is initially acceptable at 65 °C and scavenging of impurities by the porous‐spheres filler lowers this impedance relative to that with Al₂O₃. All‐solid‐state Li/LiFePO₄ and Na/NaTi₂(PO4)₃ cells give stable discharge capacity of ≈130 and 80 mAh g^?1, respectively, at 0.5 C and 65 °C for 100 cycles.     

3D Vertically Aligned Li Metal Anodes with Ultrahigh Cycling Currents and Capacities of 10 mA cm−2/20 mAh cm−2 Realized by Selective Nucleation within Microchannel Walls

Although metallic lithium is regarded as the “Holy Grail” for next‐generation rechargeable batteries due to its high theoretical capacity and low overpotential, the uncontrollable Li dendrite growth, especially under high current densities and deep plating/striping, has inhibited its practical application. Herein, a 3D‐printed, vertically aligned Li anode (3DP‐VALi) is shown to efficiently guide Li deposition via a “nucleation within microchannel walls” process, enabling a high‐performance, dendrite‐free Li anode. Moreover, the microchannels within the microwalls are beneficial for promoting fast Li⁺ diffusion, supplying large space for the accommodation of Li during the plating/stripping process. The high‐surface‐area 3D anode design enables high operating current densities and high areal capacities. As a result, the Li–Li symmetric cells using 3DP‐VALi demonstrate excellent electrochemical performances as high as 10 mA cm^?2/10 mAh cm^?2 for 1500 h and 5 mA cm^?2/20 mAh cm^?2 for 400 h, respectively. Additionally, the Li–S and Li–LiFePO₄ cells using 3DP‐VALi anodes present excellent cycling stability up to 250 and 800 cycles at a rate of 1 C, respectively. It is believed that these new findings could open a new window for dendrite‐free metal anode design and pave the way toward energy storage devices with high energy/power density.     

Porosity‐Controlled TiNb2O7 Microspheres with Partial Nitridation as A Practical Negative Electrode for High‐Power Lithium‐Ion Batteries

Titanium niobium oxide (TiNb₂O₇) has been recognized as a promising anode material for lithium‐ion batteries (LIBs) in view of its potential to operate at high rates with improved safety and high theoretical capacity of 387 mAh g^?1. However, it suffers from poor Li⁺ ion diffusivity and low electronic conductivity originated from its wide band gap energy (E_g > 2 eV). Here, porous TiNb₂O₇ microspheres (PTNO MSs) are prepared via a facile solvothermal reaction. PTNO MSs have a particle size of ≈1.2 μm and controllable pore sizes in the range of 5–35 nm. Ammonia gas nitridation treatment is conducted on PTNO MSs to introduce conducting Ti_1?xNb_xN layer on the surface and form nitridated PTNO (NPTNO) MSs. The porous structure and conducting Ti_1?xNb_xN layer enhance the transport kinetics associated with Li⁺ ions and electrons, which leads to significant improvement in electrochemical performance. As a result, the NPTNO electrode shows a high discharge capacity of ≈265 mAh g^?1, remarkable rate capability (≈143 mAh g^?1 at 100 C) and durable long‐term cyclability (≈91% capacity retention over 1000 cycles at 5 C). These results demonstrate the great potential of TiNb₂O₇ as a practical high‐rate anode material for LIBs.     

Nonwoven rGO Fiber‐Aramid Separator for High‐Speed Charging and Discharging of Li Metal Anode

Li metal, which has a high theoretical specific capacity and low redox potential, is considered to the most promising anode material for next‐generation Li ion‐based batteries. However, it also exhibits a disadvantageous solid electrolyte interphase (SEI) layer problem that needs to be resolved. Herein, an advanced separator composed of reduced graphene oxide fiber attached to aramid paper (rGOF‐A) is introduced. When rGOF‐A is applied, F^? anions, generated from the decomposition of the LiPF₆ electrolyte during the SEI layer formation process form semi‐ionic C? F bonds along the surface of rGOF. As Li⁺ ions are plated, the “F‐doped” rGO surface induces the formation of LiF, which is known as a component of a chemically stable SEI, therefore it helps the Li metal anode to operate stably at a high current of 20 mA cm^?2 with a high capacity of 20 mAh cm^?2. The proposed rGOF‐A separator successfully achieves a stable SEI layer that could resolve the interfacial issues of the Li metal anode.     

Vanadate‐Based Materials for Li‐Ion Batteries: The Search for Anodes for Practical Applications

While the practical application of electrode materials depends intensively on the Li⁺ ion storage mechanisms correlating ultimately with the coulombic efficiency, reversible capacity, and morphology variation of electrode material upon cycling, only intercalation‐type electrode materials have proven viable for commercialization up to now. This paper reviews the promising anode materials of metal vanadates (M_xV_yO_z, M = Co, Cu, Mn, Fe, Zn, Ni, Li) that have high capacity, low cost, and abundant resource, and also discusses the related Li⁺ ion storage mechanism. It is concluded that most of these (M_xV_yO_z, M = Co, Cu, Mn, Fe, Zn, Ni) exhibit irreversible redox reactions upon lithiation/delithiation accompanied by large volume expansion, which is not favorable for industrial applications. In particular, Li₃VO₄ with specific intercalation Li⁺ ion storage mechanism and compatible merits of safety and energy density exhibits great potential for practical application. This review systematically summarizes the latest progress in Li₃VO₄ research, including the representative fabrication approaches for advanced morphology and state‐of‐the‐art technologies to boost performance and the morphology variation associated with Li⁺ ion storage mechanisms. Furthermore, an outlook on where breakthroughs for Li₃VO₄ may be most likely achieved will be provided.     

Controlling Fluoride‐Forming Reactions for Improved Rate Capability in Lithium‐Perfluorinated Gas Conversion Batteries

Nonaqueous metal–gas batteries based on halogenated reactants exhibit strong potential for future high‐energy electrochemical systems. The lithium–sulfur hexafluoride (Li–SF₆) primary battery, which utilizes a safe, noncombustible, energy‐dense gas as cathode, demonstrates attractive eight‐electron transfer reduction during discharge and high attainable capacities (>3000 mAh g^?1_carbon) at voltages above 2.2 V_Li. However, improved rate capability is needed for practical applications. Here, two viable strategies are reported to achieve this by targeting the solubility of the passivating discharge product, lithium fluoride (LiF). Operating at moderately elevated temperatures, e.g., 50 °C, in DMSO dramatically improves LiF solubility and promotes sparser and larger LiF nuclei on gas diffusion layer electrodes, leading to capacity improvements of ≈10× at 120 µA cm^?2. More aggressive chemical modification of the electrolyte by including a tris(pentafluorophenyl)borane anion receptor further promotes LiF solubilization; capacity increases even at room temperature by a factor of 25 at 120 µA cm^?2, with attainable capacities up to 3 mAh cm^?2. This work shows that bulk fluoride‐forming conversion reactions can be strongly manipulated by tuning the electrolyte environment to be solvating toward F^?, and that significantly improved rates can be achieved, leading a step closer to practical applications.     

Cyclic Aminosilane‐Based Additive Ensuring Stable Electrode–Electrolyte Interfaces in Li‐Ion Batteries

Ni‐rich cathodes are considered feasible candidates for high‐energy‐density Li‐ion batteries (LIBs). However, the structural degradation of Ni‐rich cathodes on the micro‐ and nanoscale leads to severe capacity fading, thereby impeding their practical use in LIBs. Here, it is reported that 3‐(trimethylsilyl)‐2‐oxazolidinone (TMS‐ON) as a multifunctional additive promotes the dissociation of LiPF₆, prevents the hydrolysis of ion‐paired LiPF₆ (which produces undesired acidic compounds including HF), and scavenges HF in the electrolyte. Further, the presence of 0.5 wt% TMS‐ON helps maintain a stable solid–electrolyte interphase (SEI) at Ni‐rich LiNi_0.7Co_0.15Mn_0.15O₂ (NCM) cathodes, thus mitigating the irreversible phase transformation from layered to rock‐salt structures and enabling the long‐term stability of the SEI at the graphite anode with low interfacial resistance. Notably, NCM/graphite full cells with TMS‐ON, which exhibit an excellent discharge capacity retention of 80.4%, deliver a discharge capacity of 154.7 mAh g^?1 after 400 cycles at 45 °C.     

Enabling High‐Energy Solid‐State Batteries with Stable Anode Interphase by the Use of Columnar Silicon Anodes

All‐solid‐state batteries (ASSBs) with silicon anodes are promising candidates to overcome energy limitations of conventional lithium‐ion batteries. However, silicon undergoes severe volume changes during cycling leading to rapid degradation. In this study, a columnar silicon anode (col‐Si) fabricated by a scalable physical vapor deposition process (PVD) is integrated in all‐solid‐state batteries based on argyrodite‐type electrolyte (Li₆PS₅Cl, 3 mS cm^?1) and Ni‐rich layered oxide cathodes (LiNi_0.9Co_0.05Mn_0.05O₂, NCM) with a high specific capacity (210 mAh g^?1). The column structure exhibits a 1D breathing mechanism similar to lithium, which preserves the interface toward the electrolyte. Stable cycling is demonstrated for more than 100 cycles with a high coulombic efficiency (CE) of 99.7–99.9% in full cells with industrially relevant areal loadings of 3.5 mAh cm^?2, which is the highest value reported so far for ASSB full cells with silicon anodes. Impedance spectroscopy revealed that anode resistance is drastically reduced after first lithiation, which allows high charging currents of 0.9 mA cm^?2 at room temperature without the occurrence of dendrites and short circuits. Finally, in‐operando monitoring of pouch cells gave valuable insights into the breathing behavior of the solid‐state cell.     

N‐Doped Graphene Modified 3D Porous Cu Current Collector toward Microscale Homogeneous Li Deposition for Li Metal Anodes

Lithium metal is the most promising anode material for high‐energy‐density batteries due to its high specific capacity of 3860 mAh g^?1 and low reduction potential of ?3.04 V versus standard hydrogen electrode. However, huge volume change, safety concerns, and low efficiency impede the practical applications of Li metal anodes. Herein, it is shown that the nitrogen‐doped graphene modified 3D porous Cu (3DCu@NG) current collector can mitigate the above problems. The N‐doped graphene, coating on the surface of 3D current collector, not only contributes to a uniform Li⁺ flux, but also leads to a scattered distribution of electrons throughout the surface, finally contributing to a uniform Li deposition and the improved electrochemical performance. In addition, the continuously porous structure of 3DCu@NG provides a space for the metallic Li deposition and could effectually accommodate the volume expansion during cycling. As a result, the Li‐3DCu@NG anode exhibits a high areal capacity of 4 mAh cm^?2, a high Li utilization of ≈98%, and an ultralow voltage hysteresis of ≈19 mV. The multifunctional N‐doped graphene modified 3D porous current collector promisingly provides a strategy for safe and high‐energy lithium metal anodes.     

Tailoring Lithium Deposition via an SEI‐Functionalized Membrane Derived from LiF Decorated Layered Carbon Structure

Lithium (Li) metal is a key anode material for constructing next generation high energy density batteries. However, dendritic Li deposition and unstable solid electrolyte interphase (SEI) layers still prevent practical application of Li metal anodes. In this work, it is demonstrated that an uniform Li coating can be achieved in a lithium fluoride (LiF) decorated layered structure of stacked graphene (SG), leading to the formation of an SEI‐functionalized membrane that retards electron transfer by three orders of magnitude to avoid undesirable Li deposition on the top surface, and ameliorates Li⁺ ion migration to enable uniform and dendrite‐free Li deposition beneath such an interlayer. Surface chemistry analysis and density functional theory calculations demonstrate that these beneficial features arise from the formation of C–F_x surface components on the SG sheets during the Li coating process. Based on such an SEI‐functionalized membrane, stable cycling at high current densities up to 3 mA cm^?2 and Li plating capacities up to 4 mAh cm^?2 can be realized in LiPF₆/carbonate electrolytes. This work elucidates the promising strategy of modifying Li plating behavior through the SEI‐functionalized carbon structure, with significantly improved cycling stability of rechargeable Li metal anodes.