SrTiO3/Al2O3‐Graphene Electron Transport Layer for Highly Stable and Efficient Composites‐Based Perovskite Solar Cells with 20.6% Efficiency

For practical use of perovskite solar cells (PSCs) the instability issues of devices, attributed to degradation of perovskite molecules by moisture, ions migration, and thermal‐ and light‐instability, have to be solved. Herein, highly efficient and stable PSCs based on perovskite/Ag‐reduced graphene oxide (Ag‐rGO) and mesoporous Al₂O₃/graphene (mp‐AG) composites are reported. The mp‐AG composite is conductive with one‐order of magnitude higher mobility than mp‐TiO₂ and used for electron transport layer (ETL). Compared to the mp‐TiO₂ ETL based cells, the champion device based on perovskite/Ag‐rGO and SrTiO₃/mp‐AG composites shows overall a best performance (i.e., V_OC = 1.057 V, J_SC = 25.75 mA cm^?2, fill factor (FF) = 75.63%, and power conversion efficiency (PCE) = 20.58%). More importantly, the champion device without encapsulation exhibits not only remarkable thermal‐ and photostability but also long‐term stability, retaining 97–99% of the initial values of photovoltaic parameters and sustaining ≈93% of initial PCE over 300 d under ambient conditions.     

Surface Engineering of TiO2 ETL for Highly Efficient and Hysteresis‐Less Planar Perovskite Solar Cell (21.4%) with Enhanced Open‐Circuit Voltage and Stability

Interfacial studies and band alignment engineering on the electron transport layer (ETL) play a key role for fabrication of high‐performance perovskite solar cells (PSCs). Here, an amorphous layer of SnO₂ (a‐SnO₂) between the TiO₂ ETL and the perovskite absorber is inserted and the charge transport properties of the device are studied. The double‐layer structure of TiO₂ compact layer (c‐TiO₂) and a‐SnO₂ ETL leads to modification of interface energetics, resulting in improved charge collection and decreased carrier recombination in PSCs. The optimized device based on a‐SnO₂/c‐TiO₂ ETL shows a maximum power conversion efficiency (PCE) of 21.4% as compared to 19.33% for c‐TiO₂ based device. Moreover, the modified device demonstrates a maximum open‐circuit voltage (V_oc) of 1.223 V with 387 mV loss in potential, which is among the highest reported value for PSCs with negligible hysteresis. The stability results show that the device on c‐TiO₂/a‐SnO₂ retains about 91% of its initial PCE value after 500 h light illumination, which is higher than pure c‐TiO₂ (67%) based devices. Interestingly, using a‐SnO₂/c‐TiO₂ ETL the PCE loss was only 10% of initial value under continuous UV light illumination after 30 h, which is higher than that of c‐TiO₂ based device (28% PCE loss).     

Synergistic Crystal and Interface Engineering for Efficient and Stable Perovskite Photovoltaics

The presence of bulk and surface defects in perovskite light harvesting materials limits the overall efficiency of perovskite solar cells (PSCs). The formation of such defects is suppressed by adding methylammonium chloride (MACl) as a crystallization aid to the precursor solution to realize high‐quality, large‐grain triple A‐cation perovskite films and that are combined with judicious engineering of the perovskite interface with the electron and hole selective contact materials. A planar SnO₂/TiO₂ double layer oxide is introduced to ascertain fast electron extraction and the surface of the perovskite facing the hole conductor is treated with iodine dissolved in isopropanol to passivate surface trap states resulting in a retardation of radiationless carrier recombination. A maximum solar to electric power conversion efficiency (PCE) of 21.65% and open circuit photovoltage (V_oc) of ≈1.24 V with only ≈370 mV loss in potential with respect to the band gap are achieved, by applying these modifications. Additionally, the defect healing enhances the operational stability of the devices that retain 96%, 90%, and 85% of their initial PCE values after 500 h under continuously light illumination at 20, 50, and 65 °C, respectively, demonstrating one of the most stable planar PSCs reported so far.     

Long‐Lasting Nanophosphors Applied to UV‐Resistant and Energy Storage Perovskite Solar Cells

Recently, considerable progress is achieved in lab prototype perovskite solar cells (PSCs); however, the stability of outdoor applications of PSCs remains a challenge due to the high sensitivity of perovskite material under moist and ultraviolet (UV) light conditions. In this work, the UV photostability of PSC devices is improved by incorporating a photon downshifting layer—SrAl₂O₄: Eu²⁺, Dy³⁺ (SAED)—prepared using the pulsed laser deposition approach. Light‐induced deep trap states in the photoactive layer are depressed, and UV light‐induced device degradation is inhibited after the SAED modification. Optimized power conversion efficiency (PCE) of 17.8% is obtained through the enhanced light harvesting and reduced carrier recombination provided by SAED. More importantly, a solar energy storage effect due to the long‐persistent luminescence of SAED is obtained after light illumination is turned off. The introduction of downconverting material with long‐persistent luminescence in PSCs not only represents a new strategy to improve PCE and light stability by photoconversion from UV to visible light but also provides a new paradigm for solar energy storage.     

p‐Type CuI Islands on TiO2 Electron Transport Layer for a Highly Efficient Planar‐Perovskite Solar Cell with Negligible Hysteresis

Compact TiO₂ is widely used as an electron transport material in planar‐perovskite solar cells. However, TiO₂‐based planar‐perovskite solar cells exhibit low efficiencies due to intrinsic problems such as the unsuitable conduction band energy and low electron extraction ability of TiO₂. Herein, the planar TiO₂ electron transport layer (ETL) of perovskite solar cells is modified with ionic salt CuI via a simple one‐step spin‐coating process. The p‐type nature of the CuI islands on the TiO₂ surface leads to modification of the TiO₂ band alignment, resulting in barrier‐free contacts and increased open‐circuit voltage. It is found that the polarity of the CuI‐modified TiO₂ surface can pull electrons to the interface between the perovskite and the TiO₂, which improves electron extraction and reduces nonradiative recombination. The CuI solution concentration is varied to control the electron extraction of the modified TiO₂ ETL, and the optimized device shows a high efficiency of 19.0%. In addition, the optimized device shows negligible hysteresis, which is believed to be due to the removal of trap sites and effective electron extraction by CuI‐modified TiO₂. These results demonstrate the hitherto unknown effect of p‐type ionic salts on electron transport material.     

Simultaneous Improved Performance and Thermal Stability of Planar Metal Ion Incorporated CsPbI2Br All‐Inorganic Perovskite Solar Cells Based on MgZnO Nanocrystalline Electron Transporting Layer

The high thermal stability and facile synthesis of CsPbI₂Br all‐inorganic perovskite solar cells (AI‐PSCs) have attracted tremendous attention. As far as electron‐transporting layers (ETLs) are concerned, low temperature processing and reduced interfacial recombination centers through tunable energy levels determine the feasibility of the perovskite devices. Although the TiO₂ is the most popular ETL used in PSCs, its processing temperature and moderate electron mobility hamper the performance and feasibility. Herein, the highly stable, low‐temperature processed MgZnO nanocrystal‐based ETLs for dynamic hot‐air processed Mn²⁺ incorporated CsPbI2Br AI‐PSCs are reported. By holding its regular planar “n–i–p” type device architecture, the MgZnO ETL and poly(3‐hexylthiophene‐2,5‐diyl) hole transporting layer, 15.52% power conversion efficiency (PCE) is demonstrated. The thermal‐stability analysis reveals that the conventional ZnO ETL‐based AI‐PSCs show a serious instability and poor efficiency than the Mg²⁺ modified MgZnO ETLs. The photovoltaic and stability analysis of this improved photovoltaic performance is attributed to the suitable wide‐bandgap, low ETL/perovskite interface recombination, and interface stability by Mg²⁺ doping. Interestingly, the thermal stability analysis of the unencapsulated AI‐PSCs maintains >95% of initial PCE more than 400 h at 85 °C for MgZnO ETL, revealing the suitability against thermal degradation than conventional ZnO ETL.     

Lessons Learnt from Spatially Resolved Electro‐ and Photoluminescence Imaging: Interfacial Delamination in CH3NH3PbI3 Planar Perovskite Solar Cells upon Illumination

The influence of illumination on the long‐term performance of planar structured perovskite solar cells (PSCs) is investigated using fast and spatially resolved luminescence imaging. The authors analyze the effect of illuminated current density–voltage (J–V) and light‐soaking measurements on pristine PSCs by providing visual evidence for the spatial inhomogeneous evolution of device performance. Regions that are exposed to light initially produce stronger electroluminescence signals than surrounding unilluminated regions, mainly due to a lower contact resistance and, possibly, higher charge collection efficiency. Over a period of several days, however, these initially illuminated regions appear to degrade more quickly despite the device being stored in a dark, moisture‐ and oxygen‐free environment. Using transmission electron microscopy, this accelerated degradation is attributed to delamination between the perovskite and the titanium dioxide (TiO₂) layer. An ion migration mechanism is proposed for this delamination process, which is in accordance with previous current–voltage hysteresis observations. These results provide evidence for the intrinsic instability of CH₃NH₃PbI₃‐based devices under illumination and have major implications for the design of PSCs from the standpoint of long‐term performance and stability.     

Simple,Robust, and Going More Efficient: Recent Advance on Electron Transport Layer‐Free Perovskite Solar Cells

Perovskite solar cells (PSCs) have shown great potential for photovoltaic applications with their unprecedented power conversion efficiency advancement. Such devices generally have a complex structure design with high temperature processed TiO₂ as the electron transport layer (ETL). Further careful design of device configuration to fully tap the potentials of perovskite materials is expected. Particularly, for the practical application of PSCs, it is crucial to simplify their device structures thus the associated manufacturing process and cost while maintaining their efficiency to be comparable with the conventional devices. But how simple is simple? ETL‐free PSCs promise the simplest structured, thus simple manufacturing processes and low cost large area PSCs in practical applications. They can also help the further exploration of the great potential of perovskite materials and understanding the working principle of PSCs. Within this review, the evolution of the PSC is outlined by discussing the recent advances in the simplification of device configuration and processes for cost effective, highly efficient, and robust PSCs, with a focus on ETL‐free PSCs. Their advancement, key issues, working mechanism, existing problems, and future performance enhancements. This review aims to promote the future development of low cost and robust ETL‐free PSCs toward more efficient power output.     

Interface Modification by Ionic Liquid: A Promising Candidate for Indoor Light Harvesting and Stability Improvement of Planar Perovskite Solar Cells

Organic–inorganic hybrid perovskite solar cells (PSCs) are currently attracting significant interest owing to their promising outdoor performance. However, the ability of indoor light harvesting of the perovskites and corresponding device performance are rarely reported. Here, the potential of planar PSCs in harvesting indoor light for low‐power consumption devices is investigated. Ionic liquid of 1‐butyl‐3‐methylimidazolium tetrafluoroborate ([BMIM]BF₄) is employed as a modification layer of [6,6]‐phenyl‐C61‐butyric acid methyl ester) (PCBM) in the inverted PSCs. The incorporation of [BMIM]BF₄ not only paves the interface contact between PCBM and electrode, but also facilitates the electron transport and extraction owing to the efficient passivation of the surface trap states. Moreover, [BMIM]BF₄ with excellent thermal stability can act as a protective layer by preventing the erosion of moisture and oxygen into the perovskite layer. The resulting devices present a record indoor power conversion efficiency (PCE) of 35.20% under fluorescent lamps of 1000 lux, and an impressive PCE of 19.30% under 1 sun illumination. The finding in this work verifies the excellent indoor performance of PSCs to meet the requirements of eco‐friendly economy.     

Fusing Nanowires into Thin Films: Fabrication of Graded‐Heterojunction Perovskite Solar Cells with Enhanced Performance

Perovskite solar cells (PSCs) have recently experienced a rapid rise in power conversion efficiency (PCE), but the prevailing PSCs with conventional mesoscopic or planar device architectures still contain nonideal perovskite/hole‐transporting‐layer (HTL) interfaces, limiting further enhancement in PCE and device stability. In this work, CsPbBr₃ perovskite nanowires are employed for modifying the surface electronic states of bulk perovskite thin films, forming compositionally‐graded heterojunction at the perovskite/HTL interface of PSCs. The nanowire morphology is found to be key to achieving lateral homogeneity in the perovskite film surface states resulting in a near‐ideal graded heterojunction. The hidden role of such lateral homogeneity on the performance of graded‐heterojunction PSCs is revealed for the first time. The resulting PSCs show high PCE up to 21.4%, as well as high operational stability, which is superior to control PSCs fabricated without CsPbBr₃‐nanocrystals modification and with CsPbBr₃‐nanocubes modification. This study demonstrates the promise of controlled hybridization of perovskite nanowires and bulk thin films for more efficient and stable PSCs.     

Interfacing Pristine C60 onto TiO2 for Viable Flexibility in Perovskite Solar Cells by a Low‐Temperature All‐Solution Process

A low‐temperature solution‐processed strategy is critical for cost‐effective manufacture of flexible perovskite solar cells (PSCs). Based on an aqueous‐processed TiO₂ layer, and conventional fullerene derivatives replaced by a pristine fullerene interlayer of C₆₀, herein a facile interface engineering for making all‐solution‐processed TiO₂/C₆₀ layers in flexible n‐i‐p PSCs is reported. Due to the improvement of the perovskite grain quality, promotion of interfacial charge transfer and suppression of interfacial charge recombination, the stabilized power conversion efficiency for the flexible PSCs reaches as high as 16% with high bending resistance retention (≈80% after 1500 cycles) and high light‐soaking retention (≈100% after 100 min). In addition, the stabilized efficiency is over 19% for the rigid TiO₂/C₆₀‐based PSCs. The present work with the facile low‐temperature solution process renders the practicability for high‐performance flexible PSCs applied to wearable devices, portable equipment, and electric vehicles.     

Highly stable and Efficient Perovskite Solar Cells Based on FAMA‐Perovskite‐Cu:NiO Composites with 20.7% Efficiency and 80.5% Fill Factor

To solve critical issues related to device stability and performance of perovskite solar cells (PSCs), FA_0.026MA_0.974PbI_3?yCl_y‐Cu:NiO (formamidinium methylammonium (FAMA)‐perovskite‐Cu:NiO) and Al₂O₃/Cu:NiO composites are developed and utilized for fabrication of highly stable and efficient PSCs through fully‐ambient‐air processes. The FAMA‐perovskite‐Cu:NiO composite crystals prepared without using any antisolvents not only improve the perovskite film quality with large‐size crystals and less grain boundaries but also tailor optical and electronic properties and suppress charge recombination with reduction of trap density. A champion device based on the composites as light absorber and Al₂O₃/Cu:NiO interfacial layer between electron transport layer and active layer yields power conversion efficiency (PCE) of 20.67% with V_OC of 1.047 V, J_SC of 24.51 mA cm^?2, and fill factor of 80.54%. More importantly, such composite‐based PSCs without encapsulation show significant enhancement in long‐term air‐stability, thermal‐ and photostability with retaining 97% of PCE over 240 d under ambient conditions (25–30 °C, 45–55% humidity).     

Efficient and Hysteresis‐Free Perovskite Solar Cells Based on a Solution Processable Polar Fullerene Electron Transport Layer

Fullerene derivatives, which possess extraordinary geometric shapes and high electron affinity, have attracted significant attention for thin film technologies. This study demonstrates an important photovoltaic application using carboxyl‐functionalized carbon buckyballs, C60 pyrrolidine tris‐acid (CPTA), to fabricate electron transport layers (ETLs) that replace traditional metal oxide‐based ETLs in efficient and stable n‐i‐p‐structured planar perovskite solar cells (PSCs). The uniform CPTA film is covalently anchored onto the surface of indium tin oxide (ITO), significantly suppressing hysteresis and enhancing the flexural strength in the CPTA‐modified PSCs. Moreover, solution‐processable CPTA‐based ETLs also enable the fabrication of lightweight flexible PSCs. The maximum‐performing device structures composed of ITO/CPTA/CH₃NH₃PbI₃/2,2′,7,7′‐tetrakis‐(N,N‐di‐p‐methoxyphenylamine)‐9,9′‐spirobifluorene (spiro‐OMeTAD)/Au yield power conversion efficiencies of more than 18% on glass substrates and up to 17% on flexible substrates. These results indicate that the CPTA layers provide new opportunities for solution‐processed organic ETLs by substantially simplifying the procedure for fabricating PSCs for portable applications.     

Improving Interfacial Charge Recombination in Planar Heterojunction Perovskite Photovoltaics with Small Molecule as Electron Transport Layer

Although perovskite solar cells (PSCs) have emerged as a promising alternative to widely used fossil fuels, the involved high‐temperature preparation of metal oxides as a charge transport layer in most state‐of‐the‐art PSCs has been becoming a big stumbling block for future low‐temperature and large‐scale R2R manufacturing process. Such an issue strongly encourages scientists to find new type of materials to replace metal oxides. Except for expensive PC₆₁BM with unmanageable morphology and electrical properties, the past investigation on the development of low‐temperature‐processed and highly efficient electron transport layers (ETLs) has met some mixed success. In order to further enhance the performance of all‐solution‐processed PSCs, we propose a novel n‐type sulfur‐containing small molecule hexaazatrinaphtho[2,3‐c][1,2,5]thiadiazole (HATNT) with high electron mobility up to 1.73 × 10^?2 cm² V^?1 s^?1 as an ETL in planar heterojunction PSCs. A high power conversion efficiency of 18.1% is achieved, which is fully comparable with the efficiency from the control device fabricated with PC₆₁BM as ETL. This superior performance mainly attributes from more effective suppression of charge recombination at the perovskite/HATNT interface than that between the perovskite and PC₆₁ BM. Moreover, high electron mobility and strong interfacial interaction via S? I or S? Pb bonding should be also positive factors. Significantly, our results undoubtedly enable new guidelines in exploring n‐type organic small molecules for high‐performance PSCs.     

Doped Copper Phthalocyanine via an Aqueous Solution Process for Normal and Inverted Perovskite Solar Cells

Great efforts toward developing novel and efficient hole‐transporting materials are needed to further improve the device efficiency and enhance the cell stability of perovskite solar cells (PSCs). The poor film conductivity and the low carrier mobility of organic small‐molecule‐based hole‐transporting materials restrict their application in PSCs. This study develops an efficient and stable hole‐transporting material, tetrafluorotetracyanoquinodimethane (F₄‐TCNQ)‐doped copper phthalocyanine‐3,4′,4′′,4′′′‐tetra‐sulfonated acid tetra sodium salt (TS‐CuPc) via a solution process, in planar structure PSCs. The p‐type‐doped TS‐CuPc film demonstrates improved film conductivity and hole mobility owing to the strong electron affinity of F₄‐TCNQ. By the F₄‐TCNQ tailoring, the composite film gives the highest occupied molecular orbital level as high as 5.3 eV, which is beneficial for hole extraction. In addition, the aqueous solution processed TS‐CuPc:F₄‐TCNQ precursor is almost neutral with good stability for avoiding the electrode erosion. As a result, the fabricated PSCs employing TS‐CuPc:F₄‐TCNQ as the hole‐transporting material exhibit a power conversion efficiency of 16.14% in a p–i–n structure and 20.16% in an n–i–p structure, respectively. The developed organic small molecule of TS‐CuPc provides the diversification of hole‐transporting materials in planar PSCs.     

Outstanding Performance of Hole‐Blocking Layer‐Free Perovskite Solar Cell Using Hierarchically Porous Fluorine‐Doped Tin Oxide Substrate

Perovskite solar cells (PSCs) are of great interest in current photovoltaic research due to their extraordinary power conversion efficiency of ≈20% and boundless potentialities. The high efficiency has been mostly obtained from TiO₂‐based PSCs, where TiO₂ is utilized as a hole‐blocking, mesoporous layer. However, trapped charges and the light‐induced photocatalytic effect of TiO₂ seriously degrade the perovskite and preclude PSCs from being immediately commercialized. Herein, a simplified PSC is successfully fabricated by eliminating the problematic TiO₂ layers, using instead a fluorine‐doped tin oxide (FTO)/perovskite/hole–conductor/Au design. Simultaneously, the sluggish charge extraction at the FTO/perovskite interface is overcome by modifying the surface of the FTO to a porous structure using electrochemical etching. This surface engineering enables a substantial increase in the photocurrent density and mitigation of the hysteretic behavior of the pristine FTO‐based PSC; a remarkable 19.22% efficiency with a low level of hysteresis is obtained. This performance is closely approaching that of conventional PSCs and may facilitate their commercialization due to improved convenience, lower cost, greater stability, and potentially more efficient mass production.     

High‐Efficiency Low‐Temperature ZnO Based Perovskite Solar Cells Based on Highly Polar,Nonwetting Self‐Assembled Molecular Layers

Herein, this study reports high‐efficiency, low‐temperature ZnO based planar perovskite solar cells (PSCs) with state‐of‐the‐art performance. They are achieved via a strategy that combines dual‐functional self‐assembled monolayer (SAM) modification of ZnO electron accepting layers (EALs) with sequential deposition of perovskite active layers. The SAMs, constructed from newly synthesized molecules with high dipole moments, act both as excellent surface wetting control layers and as electric dipole layers for ZnO‐EALs. The insertion of SAMs improves the quality of PbI₂ layers and final perovskite layers during sequential deposition, while charge extraction is enhanced via electric dipole effects. Leveraged by SAM modification, our low‐temperature ZnO based PSCs achieve an unprecedentedly high power conversion efficiency of 18.82% with a V_OC of 1.13 V, a J_SC of 21.72 mA cm^?2, and a FF of 0.76. The strategy used in this study can be further developed to produce additional performance enhancements or fabrication temperature reductions.     

In Situ Polymerization of Cross-Linked Perovskite–Polymer Composites for Highly Stable and Efficient Perovskite Solar Cells

Mixed-halide perovskites have emerged as outstanding light absorbers that enable the fabrication of efficient solar cells; however, their instability hinders the commercialization of such systems. Grain-boundary (GB) defects and lattice tensile strain are critical intrinsic-instability factors in polycrystalline perovskite films. In this study, the light-induced cross-linking of acrylamide (Am) monomers with non-crystalline perovskite films is used to fabricate highly efficient and stable perovskite solar cells (PSCs). The Am monomers induce the preferred crystal orientation in the polycrystalline perovskite films, enlarge the perovskite grain size, and cross-link the perovskite grains. Additionally, the liquid properties of Am effectively releases lattice strain during perovskite-film crystallization. The cross-linked interfacial layer functions as an airtight wall that protects the perovskite film from water corrosion. Devices fabricated using the proposed strategy show an excellent power conversion efficiency (PCE) of 24.45% with an open-circuit voltage (V_OC) of 1.199 V, which, to date, is the highest V_OC reported for hybrid PSCs with electron transport layers (ETLs) comprised of TiO₂. Large-area PSC modules fabricated using the proposed strategy show a power conversion efficiency of 20.31% (with a high fill factor of 77.1%) over an active area of 33 cm², with excellent storage stability.     

High‐Performance Flexible Perovskite Solar Cells via Precise Control of Electron Transport Layer

Flexible perovskite solar cells (f‐PSCs) have attracted great attention due to their promising commercial prospects. However, the performance of f‐PSCs is generally worse than that of their rigid counterparts. Herein, it is found that the unsatisfactory performance of planar heterojunction (PHJ) f‐PSCs can be attributed to the undesirable morphology of electron transport layer (ETL), which results from the rough surface of the flexible substrate. Precise control over the thickness and morphology of ETL tin dioxide (SnO₂) not only reduces the reflectance of the indium tin oxide (ITO) on polyethylene 2,6‐naphthalate (PEN) substrate and enhances photon collection, but also decreases the trap‐state densities of perovskite films and the charge transfer resistance, leading to a great enhancement of device performance. Consequently, the f‐PSCs, with a structure of PEN/ITO/SnO₂/perovskite/Spiro‐OMeTAD/Ag, exhibit a power conversion efficiency (PCE) up to 19.51% and a steady output of 19.01%. Furthermore, the f‐PSCs show a robust bending resistance and maintain about 95% of initial PCE after 6000 bending cycles at a bending radius of 8 mm, and they present an outstanding long‐term stability and retain about 90% of the initial performance after >1000 h storage in air (10% relative humidity) without encapsulation.     

Few‐Layer MoS2 Flakes as Active Buffer Layer for Stable Perovskite Solar Cells

Solution‐processed few‐layer MoS₂ flakes are exploited as an active buffer layer in hybrid lead–halide perovskite solar cells (PSCs). Glass/FTO/compact‐TiO₂/mesoporous‐TiO₂/CH₃NH₃PbI₃/MoS₂/Spiro‐OMeTAD/Au solar cells are realized with the MoS₂ flakes having a twofold function, acting both as a protective layer, by preventing the formation of shunt contacts between the perovskite and the Au electrode, and as a hole transport layer from the perovskite to the Spiro‐OMeTAD. As prepared PSC demonstrates a power conversion efficiency (η) of 13.3%, along with a higher lifetime stability over 550 h with respect to reference PSC without MoS₂ (Δη/η = ?7% vs. Δη/η = ?34%). Large‐area PSCs (1.05 cm² active area) are also fabricated to demonstrate the scalability of this approach, achieving η of 11.5%. Our results pave the way toward the implementation of MoS₂ as a material able to boost the shelf life of large‐area perovskite solar cells in view of their commercialization.