High Polarity Poly(vinylidene difluoride) Thin Coating for Dendrite‐Free and High‐Performance Lithium Metal Anodes

The high‐polarity β‐phase poly(vinylidene difluoride) (β‐PVDF), which has all trans conformation with F and H atoms located on the opposite sides of the polymer backbone, is demonstrated to be a promising artificial solid‐electrolyte interphase coating on both Cu and Li metal anodes for dendrite‐free Li deposition/stripping and enhanced cycling performance. A thin (≈4 µm) β‐PVDF coating on Cu enables uniform Li deposition/stripping at high current densities up to 5 mA cm^?2, Li‐plating capacity loadings of up to 4 mAh cm^?2, and excellent cycling stability over hundreds of cycles under practical conditions (1 mA cm^?2 with 2 mAh cm^?2). Full cells containing an LiFePO₄ cathode and an anode of either β‐PVDF coated Cu or Li also exhibit excellent cycling stability. The profound effects of the high‐polarity PVDF coating on dendrite suppression are attributed to the electronegative F‐rich interface that favors layer‐by‐layer Li deposition. This study offers a new strategy for the development of dendrite‐free metal anode technology.     

Fast‐Charging and Ultrahigh‐Capacity Lithium Metal Anode Enabled by Surface Alloying

Li metal anodes are going through a great revival but they still encounter grand challenges. One often neglected issue is that most reported Li metal anodes are only cyclable under relatively low current density (<5 mA cm^?2) and small areal capacity (<5 mAh cm^?2), which essentially limits their high‐power applications and results in ineffective Li utilization (<1%). Herein, it is reported that surface alloyed Li metal anodes can enable reversible cycling with ultrafast rate and ultralarge areal capacity. Low‐cost Si wafers are used and are chemically etched down to 20–30 µm membranes. Simply laminating a Si membrane onto Li foil results in the formation of Li_xSi alloy film fused onto Li metal with mechanical robustness and high Li‐ion conductivity. Symmetric cell measurements show that the surface alloyed Li anode has excellent cycling stability, even under high current density up to 25 mA cm^?2 and unprecedented areal capacity up to 100 mAh cm^?2. Furthermore, the surface alloyed Li anode is paired with amorphous MoS₃ cathode and achieves remarkable full‐cell performance.     

3D Vertically Aligned Li Metal Anodes with Ultrahigh Cycling Currents and Capacities of 10 mA cm−2/20 mAh cm−2 Realized by Selective Nucleation within Microchannel Walls

Although metallic lithium is regarded as the “Holy Grail” for next‐generation rechargeable batteries due to its high theoretical capacity and low overpotential, the uncontrollable Li dendrite growth, especially under high current densities and deep plating/striping, has inhibited its practical application. Herein, a 3D‐printed, vertically aligned Li anode (3DP‐VALi) is shown to efficiently guide Li deposition via a “nucleation within microchannel walls” process, enabling a high‐performance, dendrite‐free Li anode. Moreover, the microchannels within the microwalls are beneficial for promoting fast Li⁺ diffusion, supplying large space for the accommodation of Li during the plating/stripping process. The high‐surface‐area 3D anode design enables high operating current densities and high areal capacities. As a result, the Li–Li symmetric cells using 3DP‐VALi demonstrate excellent electrochemical performances as high as 10 mA cm^?2/10 mAh cm^?2 for 1500 h and 5 mA cm^?2/20 mAh cm^?2 for 400 h, respectively. Additionally, the Li–S and Li–LiFePO₄ cells using 3DP‐VALi anodes present excellent cycling stability up to 250 and 800 cycles at a rate of 1 C, respectively. It is believed that these new findings could open a new window for dendrite‐free metal anode design and pave the way toward energy storage devices with high energy/power density.     

Tailoring Lithium Deposition via an SEI‐Functionalized Membrane Derived from LiF Decorated Layered Carbon Structure

Lithium (Li) metal is a key anode material for constructing next generation high energy density batteries. However, dendritic Li deposition and unstable solid electrolyte interphase (SEI) layers still prevent practical application of Li metal anodes. In this work, it is demonstrated that an uniform Li coating can be achieved in a lithium fluoride (LiF) decorated layered structure of stacked graphene (SG), leading to the formation of an SEI‐functionalized membrane that retards electron transfer by three orders of magnitude to avoid undesirable Li deposition on the top surface, and ameliorates Li⁺ ion migration to enable uniform and dendrite‐free Li deposition beneath such an interlayer. Surface chemistry analysis and density functional theory calculations demonstrate that these beneficial features arise from the formation of C–F_x surface components on the SG sheets during the Li coating process. Based on such an SEI‐functionalized membrane, stable cycling at high current densities up to 3 mA cm^?2 and Li plating capacities up to 4 mAh cm^?2 can be realized in LiPF₆/carbonate electrolytes. This work elucidates the promising strategy of modifying Li plating behavior through the SEI‐functionalized carbon structure, with significantly improved cycling stability of rechargeable Li metal anodes.     

Uniform High Ionic Conducting Lithium Sulfide Protection Layer for Stable Lithium Metal Anode

Artificial solid‐electrolyte interphase (SEI) is one of the key approaches in addressing the low reversibility and dendritic growth problems of lithium metal anode, yet its current effect is still insufficient due to insufficient stability. Here, a new principle of “simultaneous high ionic conductivity and homogeneity” is proposed for stabilizing SEI and lithium metal anodes. Fabricated by a facile, environmentally friendly, and low‐cost lithium solid‐sulfur vapor reaction at elevated temperature, a designed lithium sulfide protective layer successfully maintains its protection function during cycling, which is confirmed by both simulations and experiments. Stable dendrite‐free cycling of lithium metal anode is realized even at a high areal capacity of 5 mAh cm^?2, and prototype Li–Li₄Ti₅O₁₂ cell with limited lithium also achieves 900 stable cycles. These findings give new insight into the ideal SEI composition and structure and provide new design strategies for stable lithium metal batteries.     

Enhanced Stability of Li Metal Anodes by Synergetic Control of Nucleation and the Solid Electrolyte Interphase

Use of a protective coating on a lithium metal anode (LMA) is an effective approach to enhance its coulombic efficiency and cycling stability. Here, a facile approach to produce uniform silver nanoparticle‐decorated LMA for high‐performance Li metal batteries (LMBs) is reported. This effective treatment can lead to well‐controlled nucleation and the formation of a stable solid electrolyte interphase (SEI). Ag nanoparticles embedded in the surface of Li anodes induce uniform Li plating/stripping morphologies with reduced overpotential. More importantly, cross‐linked lithium fluoride‐rich interphase formed during Ag⁺ reduction enables a highly stable SEI layer. Based on the Ag‐LiF decorated anodes, LMBs with LiNi_1/3Mn_1/3Co_1/3O₂ cathode (≈1.8 mAh cm^?2) can retain >80% capacity over 500 cycles. The similar approach can also be used to treat sodium metal anodes. Excellent stability (80% capacity retention in 10 000 cycles) is obtained for a Na||Na₃V₂(PO₄)₃ full cell using a Na‐Ag‐NaF/Na anode cycled in carbonate electrolyte. These results clearly indicate that synergetic control of the nucleation and SEI is an efficient approach to stabilize rechargeable metal batteries.     

Artificial Solid‐Electrolyte Interphase Enabled High‐Capacity and Stable Cycling Potassium Metal Batteries

Secondary batteries based on earth‐abundant potassium metal anodes are attractive for stationary energy storage. However, suppressing the formation of potassium metal dendrites during cycling is pivotal in the development of future potassium metal‐based battery technology. Herein, a promising artificial solid‐electrolyte interphase (ASEI) design, simply covering a carbon nanotube (CNT) film on the surface of a potassium metal anode, is demonstrated. The results show that the spontaneously potassiated CNT framework with a stable self‐formed solid‐electrolyte interphase layer integrates a quasi‐hosting feature with fast interfacial ion transport, which enables dendrite‐free deposition of potassium at an ultrahigh capacity (20 mAh cm^?2). Remarkably, the potassium metal anode exhibits an unprecedented cycle life (over 1000 cycles, over 2000 h) at a high current density of 5 mA cm^?2 and a desirable areal capacity of 4 mAh cm^?2. Dendrite‐free morphology in carbon‐fiber and carbon‐black‐based ASEI for potassium metal anodes, which indicates a broader promise of this approach, is also observed.     

S‐Doped Graphene‐Regional Nucleation Mechanism for Dendrite‐Free Lithium Metal Anodes

Lithium metal is the most promising anode material for next‐generation batteries, owing to its high theoretical specific capacity and low electrochemical potential. However, the practical application of lithium metal batteries (LMBs) has been plagued by the issues of uncontrollable lithium deposition. The multifunctional nanostructured anode can modulate the initial nucleation process of lithium before the extension of dendrites. By combing the theoretical design and experimental validation, a novel nucleation strategy is developed by introducing sulfur (S) to graphene. Through first‐principles simulations, it is found that S atom doping can improve the Li adsorption ability on a large area around the S doping positions. Consequently, S‐doped graphene with five lithiophilic sites rather than a single atomic site can serve as the pristine nucleation area, reducing the uneven Li deposition and improving the electrochemical performance. Modifying Li metal anodes by S‐doped graphene enables an ultralow overpotential of 5.5 mV, a high average Coulombic efficiency of 99% over more than 180 cycles at a current density of 0.5 mA cm^?2 for 1.0 mAh cm^?2, and a high areal capacity of 3 mAh cm^?2. This work sheds new light on the rational design of nucleation area materials for dendrite‐free LMB.     

Plating/Stripping Behavior of Actual Lithium Metal Anode

Lithium (Li) metal anodes exhibits the potential to enable rechargeable Li batteries with a high energy density. However, the irreversible plating and stripping behaviors of Li metal anodes with high reactivity and dendrite growth when matching different cathodes in working cells are not fully understood yet. Herein the working manner of very thin Li metal anodes (50 µm, 10 mAh cm^?2) is probed with different sequences of Li plating and stripping at 3.0 mA cm^?2 and 3.0 mAh cm^?2. Dendrite growth and dead Li forms on the surface of the initially plated Li electrode (P‐Li), while Li dendrites form in the pit of the initially stripped Li electrode (S‐Li). This induces the differences in reactive sites, distribution of dead Li, and voltage polarization of Li metal anodes. There is a gap of 15–20 and 13–16 mV for the end voltages between S‐Li and P‐Li during stripping and plating, respectively. When matching LiFePO₄ and FePO₄ cathodes, P‐Li | LiFePO₄ cells exhibit a 30‐cycle longer lifespan with smaller end polarization due to differences in the sequences of Li plating and stripping. This contribution affords emerging working principles for actual Li metal anodes when matching lithium‐containing and lithium‐free cathodes.     

An Interconnected Channel‐Like Framework as Host for Lithium Metal Composite Anodes

Lithium (Li) metal anodes have long been counted on to meet the increasing demand for high energy, high‐power rechargeable battery systems but they have been plagued by uncontrollable plating, unstable solid electrolyte interphase (SEI) formation, and the resulting low Coulombic efficiency. These problems are even aggravated under commercial levels of current density and areal capacity testing conditions. In this work, the channel‐like structure of a carbonized eggplant (EP) as a stable “host” for Li metal melt infusion, is utilized. With further interphase modification of lithium fluoride (LiF), the as‐formed EP–LiF composite anode maintains ≈90% Li metal theoretical capacity and can successfully suppress dendrite growth and volume fluctuation during cycling. EP–LiF offers much improved symmetric cell and full‐cell cycling performance with lower and more stable overpotential under various areal capacity and elevated rate capability. Furthermore, carbonized EP serves as a light‐weight high‐performance current collector, achieving an average Coulombic efficiency ≈99.1% in ether‐based electrolytes with 2.2 mAh cm^?2 cycling areal capacity. The natural structure of carbonized EP will inspire further artificial designs of electrode frameworks for both Li anode and sulfur cathodes, enabling promising candidates for next‐generation high‐energy density batteries.     

Lithium‐Pretreated Hard Carbon as High‐Performance Sodium‐Ion Battery Anodes

Hard carbon (HC) is the state‐of‐the‐art anode material for sodium‐ion batteries (SIBs). However, its performance has been plagued by the limited initial Coulombic efficiency (ICE) and mediocre rate performance. Here, experimental and theoretical studies are combined to demonstrate the application of lithium‐pretreated HC (LPHC) as high‐performance anode materials for SIBs by manipulating the solid electrolyte interphase in tetraglyme (TEGDME)‐based electrolyte. The LPHC in TEGDME can 1) deliver > 92% ICE and ≈220 mAh g^?1 specific capacity, twice of the capacity (≈100 mAh g^?1) in carbonate electrolyte; 2) achieve > 85% capacity retention over 1000 cycles at 1000 mA g^?1 current density (4 C rate, 1 C = 250 mA g^?1) with a specific capacity of ≈150 mAh g^?1, ≈15 times of the capacity (10 mAh g^?1) in carbonate. The full cell of Na₃V₂(PO₄)₃‐LPHC in TEGDME demonstrated close to theoretical specific capacity of ≈98 mAh g^?1 based on Na₃V₂(PO₄)₃ cathode, ≈2.5 times of the value (≈40 mAh g^?1) with nontreated HC. This work provides new perception on the anode development for SIBs.     

Microscale Lithium Metal Stored inside Cellular Graphene Scaffold toward Advanced Metallic Lithium Anodes

The volume expansion and dendrite growth of metallic Li anode during charge/discharge processes hinder its practical application in energy storage. Seeking an appropriate host for distributing bulk Li in a 3D manner is an effective way to solve these problems. Here, a novel porous graphene scaffold with cellular chambers for incorporating Li metal is presented. Using such a unique host, ultrathin Li layers of 3 µm in thickness are anchored on graphene to form porous microstructures, which provides much more reaction sites for Li ions compared with that of bulk Li, significantly promoting the reversibility of Li stripping and plating. Also the high current density can be effectively dissipated by the graphene scaffold to remarkably improve the rate capability of Li anode. The symmetrical Li cell using such a Li anode can run stably for 200 cycles at 5 mA cm^?2 and even 70 cycles at 10 mA cm^?2 in an unmodified carbonate‐based electrolyte, which has rarely been achieved in such aggressive working conditions. Lithium‐ion capacitor cells using this anode also show outstanding rate capability and cycling stability, which can work at an ultrahigh current density of 30 A g^?1 and keep steady for over 4000 cycles at 3.75 A g^?1.     

Tailoring the Mechanical and Electrochemical Properties of an Artificial Interphase for High‐Performance Metallic Lithium Anode

Lithium metal is regarded as the “Holy Grail” of anode materials due to its low electrochemical potential and high theoretical capacity. Unfortunately, its unstable solid electrolyte interphase (SEI) leads to low Coulombic efficiency (CE) and serious safety issues. Herein, a hybrid nanoscale polymeric protective film with tunable composition and improved stiffness is developed by incorporating aluminum crosslinkers into the polymer chains. The Li plating/stripping process is regulated through the protective coating and the dendrite growth is effectively suppressed. Promisingly, the protected Li can deliver stable performance for more than 350 h with a cycling capacity of 2 mAh cm^?2 without a notable increase in overpotential. Moreover, a stable charge/discharge cycling in Li–O₂ batteries with the protected Li can be maintained for more than 600 h. This work provides guidance on the rational design of electrode interfaces and opens up new opportunities for the fabrication of next‐generation energy storage systems.     

A Coaxial‐Interweaved Hybrid Lithium Metal Anode for Long‐Lifespan Lithium Metal Batteries

Lithium (Li) metal is one of the most promising anode materials to construct next‐generation rechargeable batteries owing to its ultrahigh theoretical capacity and the lowest electrochemical potential. Unfortunately, practical application of Li metal batteries is severely hindered by short lifespan and safety concerns caused by Li dendrite growth during cycling. Herein, a coaxial‐interweaved hybrid Li metal anode is proposed for dendrite inhibition that significantly improves the cycling stability of Li metal batteries. The hybrid Li metal anode is fabricated by Li composition into a 3D interweaved scaffold, where each fiber of the interwoven scaffold is composed of a conductive skeleton and a coaxial lithiophilic layer modified on the surface. The coaxial‐interweaved structure endows the hybrid anode with favored Li affinity to guide uniform Li deposition, sufficient channels for ion transportation and electron conduction, and enhanced stability during Li plating and stripping. Consequently, the hybrid Li metal anode affords high Coulombic efficiency over 98.5% for 750 cycles with dendrite‐free morphologies in half cells and improved capacity retention of 80.1% after 100 cycles in LiFePO₄ full cells. The innovative coaxial‐interweaved hybrid Li metal anode demonstrates multiscale design strategy from lithiophilic modification to scaffold construction and promises the prospect of Li metal batteries for future applications.     

New Binder‐Free Metal Phosphide–Carbon Felt Composite Anodes for Sodium‐Ion Battery

Metal phosphides are promising anode candidates for sodium‐ion batteries (SIBs) due to their high specific capacity and low operating potential but suffer from poor cycling stability caused by huge volume expansion and poor solid‐state ion transfer rate. Herein, a new strategy to grow a new class of mesoporous metal phosphide nanoarrays on carbon felt (CF) as binder‐free anodes for SIBs is reported. The resultant integrated electrodes demonstrate excellent cycling life up to 1000 times (>90% retention rate) and high rate capability of 535 mAh g^?1 at a current density of 4 A g^?1. Detailed characterization reveals that the synergistic effect of unique mesoporous structure for accommodating huge volume expansion during sodiation/desodiation process, ultrasmall primary particle size (≈10 nm) for providing larger electrode/electrolyte contact area and shorter ion diffusion distance, and 3D conductive networks for facilitating the electrochemical reaction, leads to the extraordinary battery performance. Remarkably, a full SIB using the new CoP₄/CF anode and a Na₃V₂(PO₄)₂F₃ cathode delivers an average operating voltage of ≈3.0 V, a reversible capacity of 553 mAh g^?1, and very high energy density of ≈280 Wh kg^?1 for SIBs. A flexible SIB with outstanding mechanical strength based on this binder‐free new anode is also demonstrated.     

High‐Performance Lithium‐Iodine Flow Battery

A cathode‐flow lithium‐iodine (Li–I) battery is proposed operating by the triiodide/iodide (I₃^?/I^?) redox couple in aqueous solution. The aqueous Li–I battery has noticeably high energy density (≈0.28 kWh kg^?1_cell) because of the considerable solubility of LiI in aqueous solution (≈8.2 m ) and reasonably high power density (≈130 mW cm^?2 at a current rate of 60 mA cm^?2, 328 K). In the operation of cathode‐flow mode, the Li–I battery attains high storage capacity (≈90% of the theoretical capacity), Coulombic efficiency (100% ± 1% in 2–20 cycles) and cyclic performance (>99% capacity retention for 20 cycles) up to total capacity of 100 mAh.     

Dendrite‐Suppressed Lithium Plating from a Liquid Electrolyte via Wetting of Li3N

Lithium metal is an ultimate anode material to provide the highest energy density for a given cathode by providing a higher capacity and cell voltage. However, lithium is not used as the anode in commercial lithium‐ion batteries because electrochemical dendrite formation and growth during charge can induce a cell short circuit that ignites the flammable liquid electrolyte. Plating of lithium through a bed of Li₃N particles is shown to transform dendrite growth into a 3D lithium network formed by wetting the particle surfaces; plating through a Li₃N particle is without dendrite nucleation. The Li₃N particles create a higher overpotential during Li deposition than that with dendrite growth in galvanostatic charge/discharge tests. The characteristic overpotential increase is correlated with the morphological changes and a more isotropic growth behavior. The Li₃N‐modified Li electrode shows a stable cycling performance at 0.5 and 1.0 mA cm^?2 for more than 100 cycles. The origin of the bonding responsible for wetting of the Li₃N particles by lithium and for plating through a Li₃N particle is discussed.     

Ultrathin Bilayer of Graphite/SiO2 as Solid Interface for Reviving Li Metal Anode

Lithium metal anodes are expected to drive practical applications that require high energy‐density storage. However, the direct use of metallic lithium causes safety concerns, low rate capabilities, and poor cycling performance due to unstable solid electrolyte interphase (SEI) and undesired lithium dendrite growth. To address these issues, a radio frequency sputtered graphite‐SiO₂ ultrathin bilayer on a Li metal chips is demonstrated, for the first time, as an effective SEI layer. This leads to a dendrite free uniform Li deposition to achieve a stable voltage profile and outstanding long hours plating/stripping compared to the bare Li. Compared to a bare Li anode, the graphite‐SiO₂ bilayer modified Li anode coupled with lithium nickel cobalt manganese oxide cathode (NMC111) and lithium titanate shows improved capacity retention, higher capacity at higher rates, longer cycling stability, and lower voltage hysteresis. Graphite acts as an electrical bridge between the plated Li and Li electrode, which lowers the impedance and buffers the volume expansion during Li plating/stripping. Adding an ultrathin SiO₂ layer facilitates Li‐ion diffusion and lithiation/delithiation, provides higher electrolyte affinity, higher chemical stability, and higher Young's modulus to suppress the Li dendrite growth.     

Mn‐Rich P′2‐Na0.67[Ni0.1Fe0.1Mn0.8]O2 as High‐Energy‐Density and Long‐Life Cathode Material for Sodium‐Ion Batteries

Herein, P′2‐type Na_0.67[Ni_0.1Fe_0.1Mn_0.8]O₂ is introduced as a promising new cathode material for sodium‐ion batteries (SIBs) that exhibits remarkable structural stability during repetitive Na⁺ de/intercalation. The O? Ni? O? Mn? O? Fe? O bond in the octahedra of transition‐metal layers is used to suppress the elongation of the Mn? O bond and to improve the electrochemical activity, leading to the highly reversible Na storage mechanism. A high discharge capacity of ≈220 mAh g^?1 (≈605 Wh kg^?1) is delivered at 0.05 C (13 mAg^?1) with a high reversible capacity of ≈140 mAh g^?1 at 3 C and excellent capacity retention of 80% over 200 cycles. This performance is associated with the reversible P′2–OP4 phase transition and small volume change upon charge and discharge (≈3%). The nature of the sodium storage mechanism in a full cell paired with a hard carbon anode reveals an unexpectedly high energy density of ≈542 Wh kg^?1 at 0.2 C and good capacity retention of ≈81% for 500 cycles at 1 C (260 mAg^?1).     

MoN Supported on Graphene as a Bifunctional Interlayer for Advanced Li‐S Batteries

Rational design of effective polysulfide barriers is highly important for high‐performance lithium‐sulfur (Li‐S) batteries. A variety of adsorbents have been applied as interlayers to alleviate the shuttle effect. Nevertheless, the unsuccessful oxidation of Li₂S on interlayers leads to loss of active materials and blocks Li ion transport. In this work, a MoN‐based interlayer sandwiched between the C‐S cathode and the separator is developed. Such an interlayer not only strongly binds lithium polysulfides via Mo‐S bonding but also efficiently accelerates the decomposition of Li₂S. The acceleration mechanism toward Li₂S decomposition is determined to be a combination of contributions of catalytic cleavage of Li‐S bond in Li₂S based on the proposed covalence‐activation mechanism and rapid migration of the produced Li ions. As a result, the C–S cathodes with the as‐developed interlayer manifest a negligible charging potential barrier and outstanding cycling stability with a very low capacity fading rate of 0.023% per cycle during 1500 cycles at 1 C. High areal capacity of 6.02 mAh cm^?2 is achieved for high sulfur loading of 7.0 mg cm^?2 after cycling at 0.1 C. The material and strategy demonstrated in this work can open the door toward developing shuttle suppression interlayers without impairing cathode performance.