Recent Progress in High Donor Electrolytes for Lithium–Sulfur Batteries

Lithium–sulfur (Li–S) batteries continue to be considered promising post‐lithium‐ion batteries owing to their high theoretical energy density. In pursuit of a Li–S cell with long‐term cyclability, most studies thus far have relied on using ether‐based electrolytes. However, their limited ability to dissolve polysulfides requires a high electrolyte‐to‐sulfur ratio, which impairs the achievable specific energy. Recently, the battery community found high donor electrolytes to be a potential solution to this shortcoming because their high solubility toward polysulfides enables a cell to operate under lean electrolyte conditions. Despite the increasing number of promising outcomes with high donor electrolytes, a critical hurdle related to stability of the lithium‐metal counter electrode needs to be overcome. This review provides an overview of recent efforts pertaining to high donor electrolytes in Li–S batteries and is intended to raise interest from within the community. Furthermore, based on analogous efforts in the lithium‐air battery field, strategies for protecting the lithium metal electrode are proposed. It is predicted that high donor electrolytes will be elevated to a higher status in the field of Li–S batteries, with the hope that either existing or upcoming strategies will, to a fair extent, mitigate the degradation of the lithium–metal interface.     

Unraveling the Dual Functionality of High‐Donor‐Number Anion in Lean‐Electrolyte Lithium‐Sulfur Batteries

Minimizing electrolyte use is essential to achieve high practical energy density of lithium–sulfur (Li–S) batteries. However, the sulfur cathode is more readily passivated under a lean electrolyte condition, resulting in low sulfur utilization. In addition, continuous electrolyte decomposition on the Li metal anode aggravates the problem, provoking rapid capacity decay. In this work, the dual functionalities of NO₃^? as a high‐donor‐number (DN) salt anion is presented, which improves the sulfur utilization and cycling stability of lean‐electrolyte Li–S batteries. The NO₃^? anion elevates the solubility of the sulfur species based on its high electron donating ability, achieving a high sulfur utilization of above 1200 mA h g^?1. Furthermore, the anion suppresses electrolyte decomposition on the Li metal by regulating the lithium ion (Li⁺) solvation sheath, enhancing the cycle performance of the lean electrolyte cell. By understanding the anionic effects, this work demonstrates the potential of the high‐DN electrolyte, which is beneficial for both the cathode and anode of Li–S batteries.     

Highly Solvating Electrolytes for Lithium–Sulfur Batteries

There is a critical need to evaluate lithium–sulfur (Li–S) batteries with practically relevant high sulfur loadings and minimal electrolyte. Under such conditions, the concentration of soluble polysulfide intermediates in the electrolyte drastically increases, which can alter the fundamental nature of the solution‐mediated discharge and thereby the total sulfur utilization. In this work, an investigation into various high donor number (DN) electrolytes that allow for increased polysulfide dissolution is presented, and the way in which this property may in fact be necessary for increasing sulfur utilization at low electrolyte and high loading conditions is demonstrated. The solvents dimethylacetamide, dimethyl sulfoxide, and 1‐methylimidazole are holistically evaluated against dimethoxyethane as electrolyte co‐solvents in Li–S cells, and they are used to investigate chemical and electrochemical properties of polysulfide species at both dilute and practically relevant conditions. The nature of speciation exhibited by lithium polysulfides is found to vary significantly between these concentrations, particularly with regard to the S₃^?? species. Furthermore, the extent of the instability in conventional electrolyte solvents and high DN solvents with both lithium metal and polysulfides is thoroughly investigated. These studies establish a basis for future efforts into rationally designing an optimal electrolyte for a lean electrolyte, high energy density Li–S battery.     

Regulating the Hidden Solvation‐Ion‐Exchange in Concentrated Electrolytes for Stable and Safe Lithium Metal Batteries

Lithium–sulfur batteries are attractive for automobile and grid applications due to their high theoretical energy density and the abundance of sulfur. Despite the significant progress in cathode development, lithium metal degradation and the polysulfide shuttle remain two critical challenges in the practical application of Li–S batteries. Development of advanced electrolytes has become a promising strategy to simultaneously suppress lithium dendrite formation and prevent polysulfide dissolution. Here, a new class of concentrated siloxane‐based electrolytes, demonstrating significantly improved performance over the widely investigated ether‐based electrolytes are reported in terms of stabilizing the sulfur cathode and Li metal anode as well as minimizing flammability. Through a combination of experimental and computational investigation, it is found that siloxane solvents can effectively regulate a hidden solvation‐ion‐exchange process in the concentrated electrolytes that results from the interactions between cations/anions (e.g., Li⁺, TFSI^?, and S^2?) and solvents. As a result, it could invoke a quasi‐solid‐solid lithiation and enable reversible Li plating/stripping and robust solid‐electrolyte interphase chemistries. The solvation‐ion‐exchange process in the concentrated electrolytes is a key factor in understanding and designing electrolytes for other high‐energy lithium metal batteries.     

Tailored Reaction Route by Micropore Confinement for Li–S Batteries Operating under Lean Electrolyte Conditions

Lithium‐sulfur (Li–S) batteries are one of the most promising alternative energy storage systems beyond Li‐ion batteries. However, the sluggish kinetics of the nucleation and growth of the solid discharge product of Li₂S/Li₂S₂ in the lower discharge plateau has been recently identified as a critical hurdle for attaining high specific capacity in Li–S batteries with high sulfur loadings under lean electrolyte conditions. Herein, a new strategy of breaking the charge‐transport bottleneck by successful generation of experimentally verified stable Li₂S₂ and a reservoir of quasi‐solid lithium polysulfides within the micropores of activated carbon fiber cloth as a high‐sulfur‐loading host is proposed. The developed Li–S cell is capable of delivering a highly sustainable areal capacity of 6.0 mAh cm^?2 under lower electrolyte to sulfur ratios (<3.0 mL_E g_S^?1). Micropore confinement leads to generation of solid Li₂S₂ that enables high utilization of the entire electroactive area by its inherent self‐healing capacity. This strategy opens a new avenue for rational material designs for Li–S batteries under lean electrolyte condition.     

Boosting Polysulfide Redox Kinetics by Graphene‐Supported Ni Nanoparticles with Carbon Coating

Lithium–sulfur batteries have attracted extensive attention because of their high energy density. However, their application is still impeded by the inherent sluggish kinetics and solubility of intermediate products (i.e., polysulfides) of the sulfur cathode. Herein, graphene‐supported Ni nanoparticles with a carbon coating are fabricated by directly carbonizing a metal–organic framework/graphene oxide composite, which is then dispersed on a commercial glass fiber membrane to form a separator with electrocatalytic activity. In situ analysis and electrochemical investigation demonstrate that this modified separator can effectively suppress the shuttle effect and regulate the catalytic conversion of intercepted polysulfides, which is also confirmed by density functional theory calculations. It is found that Ni–C sites can chemically interact with polysulfides and stabilize the radical S₃^?? through Ni? S bonds to enable fast dynamic equilibrium with S₆^2?, while Ni nanoparticles reduce the oxidation barrier of Li₂S and accelerate ion/electron transport. As a result, the corresponding lithium–sulfur battery shows a high cycle stability (88% capacity retention over 100 cycles) even with a high sulfur mass loading of 8 mg cm^?2 and lean electrolyte (6.25 µ L mg^?1). Surprisingly, benefitting from the improved kinetics, the battery can work well at ?50 °C, which is rarely achieved by conventional Li–S batteries.     

Rational Design of Hierarchical “Ceramic‐in‐Polymer” and “Polymer‐in‐Ceramic” Electrolytes for Dendrite‐Free Solid‐State Batteries

Solid polymer electrolytes as one of the promising solid‐state electrolytes have received extensive attention due to their excellent flexibility. However, the issues of lithium (Li) dendrite growth still hinder their practical applications in solid‐state batteries (SSBs). Herein, composite electrolytes from “ceramic‐in‐polymer” (CIP) to “polymer‐in‐ceramic” (PIC) with different sizes of garnet particles are investigated for their effectiveness in dendrite suppression. While the CIP electrolyte with 20 vol% 200 nm Li_6.4La₃Zr_1.4Ta_0.6O₁₂ (LLZTO) particles (CIP‐200 nm) exhibits the highest ionic conductivity of 1.6 × 10^?4 S cm^?1 at 30 °C and excellent flexibility, the PIC electrolyte with 80 vol% 5 µm LLZTO (PIC‐5 µm) shows the highest tensile strength of 12.7 MPa. A sandwich‐type composite electrolyte (SCE) with hierarchical garnet particles (a PIC‐5 µm interlayer sandwiched between two CIP‐200 nm thin layers) is constructed to simultaneously achieve dendrite suppression and excellent interfacial contact with Li metal. The SCE enables highly stable Li plating/stripping cycling for over 400 h at 0.2 mA cm^?2 at 30 °C. The LiFePO₄/SCE/Li cells also demonstrate excellent cycle performance at room temperature. Fabricating sandwich‐type composite electrolytes with hierarchical filler designs can be an effective strategy to achieve dendrite‐free SSBs with high performance and high safety at room temperature.     

Minimizing the Electrolyte Volume in Li–S Batteries: A Step Forward to High Gravimetric Energy Density

Sulfur electrodes confined in an inert carbon matrix show practical limitations and concerns related to low cathode density. As a result, these electrodes require a large amount of electrolyte, normally three times more than the volume used in commercial Li‐ion batteries. Herein, a high‐energy and high‐performance lithium–sulfur battery concept, designed to achieve high practical capacity with minimum volume of electrolyte is proposed. It is based on deposition of polysulfide species on a self‐standing and highly conductive carbon nanofiber network, thus eliminating the need for a binder and current collector, resulting in high active material loading. The fiber network has a functionalized surface with the presence of polar oxygen groups, with the aim to prevent polysulfide migration to the lithium anode during the electrochemical process, by the formation of S–O species. Owing to the high sulfur loading (6 mg cm^?2) and a reduced free volume of the sulfide/fiber electrode, the Li–S cell is designed to work with as little as 10 µL cm^?2 of electrolyte. With this design the cell has a high energy density of 450 Wh kg^?1, a lifetime of more than 400 cycles, and the possibility of low cost, by use of abundant and eco‐friendly materials.     

Countersolvent Electrolytes for Lithium‐Metal Batteries

Development of electrolytes that simultaneously have high ionic conductivity, wide electrochemical window, and lithium dendrite suppression ability is urgently required for high‐energy lithium‐metal batteries (LMBs). Herein, an electrolyte is designed by adding a countersolvent into LiFSI/DMC (lithium bis(fluorosulfonyl)amide/dimethyl carbonate) electrolytes, forming countersolvent electrolytes, in which the countersolvent is immiscible with the salt but miscible with the carbonate solvents. The solvation structure and unique properties of the countersolvent electrolyte are investigated by combining electroanalytical technology with a Molecular Dynamics simulation. Introducing the countersolvent alters the coordination shell of Li⁺ cations and enhances the interaction between Li⁺ cations and FSI^? anions, which leads to the formation of a LiF‐rich solid electrolyte interphase, arising from the preferential reduction of FSI^? anions. Notably, the countersolvent electrolyte suppresses Li dendrites and enables stable cycling performance of a Li||NCM622 battery at a high cut‐off voltage of 4.6 V at both 25 and 60 °C. This study provides an avenue to understand and design electrolytes for high‐energy LMBs in the future.     

Perovskite Membranes with Vertically Aligned Microchannels for All‐Solid‐State Lithium Batteries

Perovskite‐type solid‐state electrolytes exhibit great potential for the development of all‐solid‐state lithium batteries due to their high Li‐ion conductivity (approaching 10^?3 S cm^?1), wide potential window, and excellent thermal/chemical stability. However, the large solid–solid interfacial resistance between perovskite electrolytes and electrode materials is still a great challenge that hinders the development of high‐performance all‐solid‐state lithium batteries. In this work, a perovskite‐type Li_0.34La_0.51TiO₃ (LLTO) membrane with vertically aligned microchannels is constructed by a phase‐inversion method. The 3D vertically aligned microchannel framework membrane enables more effective Li‐ion transport between the cathode and solid‐state electrolyte than a planar LLTO membrane. A significant decrease in the perovskite/cathode interfacial resistance, from 853 to 133 Ω cm², is observed. It is also demonstrated that full cells utilizing LLTO with vertically aligned microchannels as the electrolyte exhibit a high specific capacity and improved rate performance.     

Fluorine‐Free Noble Salt Anion for High‐Performance All‐Solid‐State Lithium–Sulfur Batteries

Amongst post‐Li‐ion battery technologies, lithium–sulfur (Li–S) batteries have captured an immense interest as one of the most appealing devices from both the industrial and academia sectors. The replacement of conventional liquid electrolytes with solid polymer electrolytes (SPEs) enables not only a safer use of Li metal (Li°) anodes but also a flexible design in the shape of Li–S batteries. However, the practical implementation of SPEs‐based all‐solid‐state Li–S batteries (ASSLSBs) is largely hindered by the shuttling effect of the polysulfide intermediates and the formation of dendritic Li° during the battery operation. Herein, a fluorine‐free noble salt anion, tricyanomethanide [C(CN)₃^?, TCM^?], is proposed as a Li‐ion conducting salt for ASSLSBs. Compared to the widely used perfluorinated anions {e.g., bis(trifluoromethanesulfonyl)imide anion, [N(SO₂CF₃)₂)]^?, TFSI^?}, the LiTCM‐based electrolytes show decent ionic conductivity, good thermal stability, and sufficient anodic stability suiting the cell chemistry of ASSLSBs. In particular, the fluorine‐free solid electrolyte interphase layer originating from the decomposition of LiTCM exhibits a good mechanical integrity and Li‐ion conductivity, which allows the LiTCM‐based Li–S cells to be cycled with good rate capability and Coulombic efficiency. The LiTCM‐based electrolytes are believed to be the most promising candidates for building cost‐effective and high energy density ASSLSBs in the near future.     

Localized High‐Concentration Electrolytes Boost Potassium Storage in High‐Loading Graphite

Reversible intercalation of potassium‐ion (K⁺) into graphite makes it a promising anode material for rechargeable potassium‐ion batteries (PIBs). However, the current graphite anodes in PIBs often suffer from poor cyclic stability with low coulombic efficiency. A stable solid electrolyte interphase (SEI) is necessary for stabilizing the large interlayer expansion during K⁺ insertion. Herein, a localized high‐concentration electrolyte (LHCE) is designed by adding a highly fluorinated ether into the concentrated potassium bis(fluorosulfonyl)imide/dimethoxyethane, which forms a durable SEI on the graphite surface and enables highly reversible K⁺ intercalation/deintercalation without solvent cointercalation. Furthermore, this LHCE shows a high ionic conductivity (13.6 mS cm^?1) and excellent oxidation stability up to 5.3 V (vs K⁺/K), which enables compatibility with high‐voltage cathodes. The kinetics study reveals that K⁺ intercalation/deintercalation does not follow the same pathway. The potassiated graphite exhibits excellent depotassiation rate capability, while the formation of a low stage intercalation compound is the rate‐limiting step during potassiation.     

Theoretical Investigation of 2D Conductive Microporous Coordination Polymers as Li–S Battery Cathode with Ultrahigh Energy Density

Even though tremendous achievement has been made experimentally in the performance of lithium–sulfur (Li–S) battery, theoretical studies in this area are lagging behind due to the complexity of the Li–S systems and the effects of solvent. For this purpose, a new methodology is developed for investigating the 2D hexaaminobenzene‐based coordination polymers (2D‐HAB‐CPs) as cathode candidate materials for Li–S batteries via density functional theory calculations in combination with an in‐house developed charge polarized solvent model and a genetic algorithm structure global search code. With high ratios of transition metal atoms and two‐coordinated nitrogen atoms, excellent electric conductivity, and structural porosity, the 2D‐HAB‐CP is able to address all of the three main challenges facing Li–S batteries: confining the lithium polysulfides from dissolution, facilitating the electron conductivity and buffering the volumetric expansion during the lithiation process. In addition, the theoretical energy density of this system is as high as 1395 Wh kg^?1. These results demonstrate that the 2D‐HAB‐CP is a promising cathode material for Li–S batteries. The proposed computational framework not only opens a new avenue for understanding the key role played by solution and liquid electrolytes in Li–S batteries, but also can be generally applied to other processes with liquids involved.     

An Efficient Separator with Low Li‐Ion Diffusion Energy Barrier Resolving Feeble Conductivity for Practical Lithium–Sulfur Batteries

Due to unprecedented features including high‐energy density, low cost, and light weight, lithium–sulfur batteries have been proposed as a promising successor of lithium‐ion batteries. However, unresolved detrimental low Li‐ion transport rates in traditional carbon materials lead to large energy barrier in high sulfur loading batteries, which prevents the lithium–sulfur batteries from commercialization. In this report, to overcome the challenge of increasing both the cycling stability and areal capacity, a metallic oxide composite (NiCo₂O₄@rGO) is designed to enable a robust separator with low energy barrier for Li‐ion diffusion and simultaneously provide abundant active sites for the catalytic conversion of the polar polysulfides. With a high sulfur‐loading of 6 mg cm^?2 and low sulfur/electrolyte ratio of 10, the assembled batteries deliver an initial capacity of 5.04 mAh cm^?2 as well as capacity retention of 92% after 400 cycles. The metallic oxide composite NiCo₂O₄@rGO/PP separator with low Li‐ion diffusion energy barrier opens up the opportunity for lithium–sulfur batteries to achieve long‐cycle, cost‐effective operation toward wide applications in electric vehicles and electronic devices.     

Carbon Quantum Dots–Modified Interfacial Interactions and Ion Conductivity for Enhanced High Current Density Performance in Lithium–Sulfur Batteries

Significant progress has achieved for developing lithium–sulfur (Li–S) batteries with high specific capacities and excellent cyclic stability. However, some critical issues emerge when attempts are made to raise the areal sulfur loading and increase the operation current density to meet the standards for various industrial applications. In this work, polyethylenimine‐functionalized carbon dots (PEI‐CDots) are designed and prepared for enhancing performance of the Li–S batteries with high sulfur loadings and operation under high current density situations. Strong chemical binding effects towards polysulfides and fast ion transport property are achieved in the PEI‐CDots‐modified cathodes. At a high current density of 8 mA cm^?2, the PEI‐CDots‐modified Li–S battery delivers a reversible areal capacity of 3.3 mAh cm^?2 with only 0.07% capacity decay per cycle over 400 cycles at 6.6 mg sulfur loading. Detailed analysis, involving electrochemical impedance spectroscopy, cyclic voltammetry, and density functional theory calculations, is done for the elucidation of the underlying enhancement mechanism by the PEI‐CDots. The strongly localized sulfur species and the promoted Li⁺ ion conductivity at the cathode–electrolyte interface are revealed to enable high‐performance Li–S batteries with high sulfur loading and large operational current.     

Dense Graphene Monolith for High Volumetric Energy Density Li–S Batteries

Despite the outstanding gravimetric performance of lithium–sulfur (Li–S) batteries, their practical volumetric energy density is normally lower than that of lithium‐ion batteries, mainly due to the low density of nanostructured sulfur as well as the porous carbon hosts. Here, a novel approach is developed to fabricate high‐density graphene bulk materials with “ink‐bottle‐like” mesopores by phosphoric acid (H₃PO₄) activation. These pores can effectively confine the polysulfides due to their unique structure with a wide body and narrow neck, which shows only a 0.05% capacity fade per cycle for 500 cycles (75% capacity retention) for accommodating polysulfides. With a density of 1.16 g cm^?3, a hybrid cathode containing 54 wt% sulfur delivers a high volumetric capacity of 653 mA h cm^?3. As a result, a device‐level volumetric energy density as high as 408 W h L^?1 is achieved with a cathode thickness of 100 µm. This is a periodic yet practical advance to improve the volumetric performance of Li–S batteries from a device perspective. This work suggests a design principle for the real use Li–S batteries although there is a long way ahead to bridge the gap between Li–S batteries and Li–ion batteries in volumetric performance.     

In Situ Generation of Artificial Solid‐Electrolyte Interphases on 3D Conducting Scaffolds for High‐Performance Lithium‐Metal Anodes

Rational structure design of the current collector along with further engineering of the solid‐electrolyte interphases (SEI) layer is one of the most promising strategies to achieve uniform Li deposition and inhibit uncontrolled growth of Li dendrites. Here, a Li₂S layer as an artificial SEI with high compositional uniformity and high lithium ion conductivity is in situ generated on the surface of the 3D porous Cu current collector to regulate homogeneous Li plating/stripping. Both simulations and experiments demonstrate that the Li₂S protective layer can passivate the porous Cu skeleton and balance the transport rate of lithium ions and electrons, thereby alleviating the agglomerated Li deposition at the top of the electrode or at the defect area of the SEI layer. As a result, the modified current collector exhibits long‐term cycling of 500 cycles at 1 mA cm^?2 and stable electrodeposition capabilities of 4 mAh cm^?2 at an ultrahigh current density of 4 mA cm^?2. Furthermore, full batteries (LiFePO₄ as cathode) paired with this designed 3D anode with only ≈200% extra lithium show superior stability and rate performance than the batteries paired with lithium foil (≈3000% extra lithium). These explorations provide new strategies for developing high‐performance Li metal anodes.     

All‐Solid‐State Printed Bipolar Li–S Batteries

Despite their potential advantages over currently widespread lithium‐ion batteries, lithium–sulfur (Li–S) batteries are not yet in practical use. Here, for the first time bipolar all‐solid‐state Li–S batteries (ASSLSBs) are demonstrated that exhibit exceptional safety, flexibility, and aesthetics. The bipolar ASSLSBs are fabricated through a solvent‐drying‐free, ultraviolet curing‐assisted stepwise printing process at ambient conditions, without (high‐temperature/high‐pressure) sintering steps that are required for inorganic electrolyte‐based all‐solid‐state batteries. Two thermodynamically immiscible and nonflammable gel electrolytes based on ethyl methyl sulfone (EMS) and tetraethylene glycol dimethyl ether (TEGDME) are used to address longstanding concerns regarding the grain boundary resistance of conventional inorganic solid electrolytes, as well as the polysulfide shuttle effect in Li–S batteries. The EMS gel electrolytes embedded in the sulfur cathodes facilitate sulfur utilization, while the TEGDME gel composite electrolytes serve as polysulfide‐repelling separator membranes. Benefiting from the well‐designed cell components and printing‐driven facile processability, the resulting bipolar ASSLSBs exhibit unforeseen advancements in bipolar cell configuration, safety, foldability, and form factors, which lie far beyond those achievable with conventional Li–S battery technologies.     

A Lithium Amide‐Borohydride Solid‐State Electrolyte with Lithium‐Ion Conductivities Comparable to Liquid Electrolytes

High ionic conductivity of up to 6.4 × 10^?3 S cm^?1 near room temperature (40 °C) in lithium amide‐borohydrides is reported, comparable to values of liquid organic electrolytes commonly employed in lithium‐ion batteries. Density functional theory is applied coupled with X‐ray diffraction, calorimetry, and nuclear magnetic resonance experiments to shed light on the conduction mechanism. A Li₄Ti₅O₁₂ half‐cell battery incorporating the lithium amide‐borohydride electrolyte exhibits good rate performance up to 3.5 mA cm^?2 (5 C) and stable cycling over 400 cycles at 1 C at 40 °C, indicating high bulk and interfacial stability. The results demonstrate the potential of lithium amide‐borohydrides as solid‐state electrolytes for high‐power lithium‐ion batteries.     

Viscoelastic and Nonflammable Interface Design–Enabled Dendrite‐Free and Safe Solid Lithium Metal Batteries

Herein, a composite polymer electrolyte with a viscoelastic and nonflammable interface is designed to handle the contact issue and preclude Li dendrite formation. The composite polymer electrolyte (cellulose acetate/polyethylene glycol/Li_1.4Al_0.4Ti_1.6P₃O₁₂) exhibits a wide electrochemical window of 5 V (vs Li⁺/Li), a high Li⁺ transference number of 0.61, and an excellent ionic conductivity of above 10^?4 S cm^?1 at 60 °C. In particular, the intimate contact, low interfacial impedance, and fast ion‐transport process between the electrodes and solid electrolytes can be simultaneously achieved by the viscoelastic and nonflammable layer. Benefiting from this novel design, solid lithium metal batteries with either LiFePO₄ or LiCoO₂ as cathode exhibit superior cyclability and rate capability, such as a discharge capacity of 157 mA h g^?1 after 100 cycles at C/2 and 97 mA h g^?1 at 5C for LiFePO₄ cathode. Moreover, the smooth and uniform Li surface after long‐term cycling confirms the successful suppression of dendrite formation. The viscoelastic and nonflammable interface modification of solid electrolytes provides a promising and general strategy to handle the interfacial issues and improves the operative safety of solid lithium metal batteries.