Electron‐Beam‐Evaporated Nickel Oxide Hole Transport Layers for Perovskite‐Based Photovoltaics

High‐quality charge carrier transport materials are of key importance for stable and efficient perovskite‐based photovoltaics. This work reports on electron‐beam‐evaporated nickel oxide (NiO_x) layers, resulting in stable power conversion efficiencies (PCEs) of up to 18.5% when integrated into solar cells employing inkjet‐printed perovskite absorbers. By adding oxygen as a process gas and optimizing the layer thickness, transparent and efficient NiO_x hole transport layers (HTLs) are fabricated, exhibiting an average absorptance of only 1%. The versatility of the material is demonstrated for different absorber compositions and deposition techniques. As another highlight of this work, all‐evaporated perovskite solar cells employing an inorganic NiO_x HTL are presented, achieving stable PCEs of up to 15.4%. Along with good PCEs, devices with electron‐beam‐evaporated NiO_x show improved stability under realistic operating conditions with negligible degradation after 40 h of maximum power point tracking at 75 °C. Additionally, a strong improvement in device stability under ultraviolet radiation is found if compared to conventional perovskite solar cell architectures employing other metal oxide charge transport layers (e.g., titanium dioxide). Finally, an all‐evaporated perovskite solar mini‐module with a NiO_x HTL is presented, reaching a PCE of 12.4% on an active device area of 2.3 cm².     

Hot‐Substrate Deposition of Hole‐ and Electron‐Transport Layers for Enhanced Performance in Perovskite Solar Cells

Charge transport layers play an important role in determining the power conversion efficiencies (PCEs) of perovskite solar cells (PSCs). However, it has proven challenging to produce thin and compact charge transport layers via solution processing techniques. Herein, a hot substrate deposition method capable of improving the morphology of high‐coverage hole‐transport layers (HTLs) and electron‐transport layers (ETLs) is reported. PSC devices using HTLs deposited on a hot substrate show improvement in the open‐circuit voltage (V_oc) from 1.041 to 1.070 V and the PCE from 17.00% to 18.01%. The overall device performance is then further enhanced with the hot substrate deposition of ETLs as the V_oc and PCE reach 1.105 V and 19.16%, respectively. The improved performance can be explained by the decreased current leakage and series resistance, which are present in PSCs with rough and discontinuous HTLs and ETLs.     

Cesium Doped NiOx as an Efficient Hole Extraction Layer for Inverted Planar Perovskite Solar Cells

Organic–inorganic hybrid perovskite solar cells have resulted in tremendous interest in developing next generation photovoltaics due to high record efficiency exceeding 22%. For inverted structure perovskite solar cells, the hole extraction layers play a significant role in achieving efficient and stable perovskite solar cell by modifying charge extraction, interfacial recombination losses, and band alignment. Here, cesium doped NiO_x is selected as a hole extraction layer to study the impact of Cs dopant on the optoelectronic properties of NiO_x and the photovoltaic performance. Cs doped NiO_x films are prepared by a simple solution‐based method. Both doped and undoped NiO_x films are smooth and highly transparent, while the Cs doped NiO_x exhibits better electron conductivity and higher work function. Therefore, Cs doping results in a significant improvement in the performance of NiO_x‐based inverted planar perovskite solar cells. The best efficiency of Cs doped NiO_x devices is 19.35%, and those devices show high stability as well. The improved efficiency in devices with Cs:NiO_x is attributed to a significant improvement in the hole extraction and better band alignment compared to undoped NiO_x. This work reveals that Cs doped NiO_x is very promising hole extraction material for high and stable inverted perovskite solar cells.     

Strategic Synthesis of Ultrasmall NiCo2O4 NPs as Hole Transport Layer for Highly Efficient Perovskite Solar Cells

This study proposes a novel strategy of controllable deamination of Co–NH₃ complexes in a system containing Ni(OH)₂ to synthesize ultrasmall ternary oxide nanoparticles (NPs), NiCo₂O₄. Through this approach, ultrasmall (5 nm on average) and well‐dispersed NiCo₂O₄ NPs without exotic ligands are obtained, which enables the formation of uniform and pin‐hole free films. The tightly covered NiCo₂O₄ films also facilitate the formation of large perovskite grains and thus reduce film defects. The results show that with the NiCo₂O₄ NPs as the hole transport layer (HTL), the perovskite solar cells reach a high power conversion efficiency (PCE) of 18.23% and a promising stability (maintained ≈90% PCE after 500 h light soaking). To the best of the author's knowledge, it is the first time that spinel NiCo₂O₄ NPs have been applied as hole transport layer in perovskite solar cells successfully. This work not only demonstrates the potential applications of ternary oxide NiCo₂O₄ as HTLs in hybrid perovskite solar cells but also provides an insight into the design and synthesis of ultrasmall and ligand‐free NPs HTLs to enable cost‐effective photovoltaic devices.     

High‐Performance Planar Perovskite Solar Cells Using Low Temperature,Solution–Combustion‐Based Nickel Oxide Hole Transporting Layer with Efficiency Exceeding 20%

NiO_x hole transporting layer has been extensively studied in optoelectronic devices. In this paper, the low temperature, solution–combustion‐based method is employed to prepare the NiO_x hole transporting layer. The resulting NiO_x thin films show better quality and preferable energy alignment with perovskite thin film compared to high temperature sol–gel‐processed NiO_x. With this, high‐performance perovskite solar cells are fabricated successfully with power conversion efficiency exceeding 20% using a modified two‐step prepared MA_1?yFA_yPbI_3?xCl_x perovskite. This efficiency value is among the highest values for NiO_x‐based devices. Various characterizations and analyses provide evidence of better film quality, enhanced charge transport and extraction, and suppressed charge recombination. Meanwhile, the device exhibits much better device stability compared to sol–gel‐processed NiO_x and poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate)‐based devices.     

Overcoming Interfacial Losses in Solution‐Processed Organic Multi‐Junction Solar Cells

Organic solar cells are promising in terms of full‐solution‐processing which enables low‐cost and large‐scale fabrication. While single‐junction solar cells have seen a boost in power conversion efficiency (PCE), multi‐junction solar cells are promising to further enhance the PCE. In all‐solution‐processed multi‐junction solar cells, interfacial losses are often encountered between hole‐transporting layer (HTL) and the active layers and therefore greatly limit the application of newly developed high‐performance donor and acceptor materials in multi‐junction solar cells. Here, the authors report on a systematic study of interface losses in both single‐junction and multi‐junction solar cells based on representative polymer donors and HTLs using electron spectroscopy and time‐of‐flight secondary ion mass spectrometry. It is found that a facile mixed HTL containing poly(3,4‐ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) and MoO _x nanoparticles successfully overcomes the interfacial losses in both single‐ and multi‐junction solar cells based on various active layers by reducing interface protonation, promoting better energy‐level alignment, and forming a dense and smooth layer. Solution‐processed single‐junction solar cells are demonstrated to reach the same performance as with evaporated MoO _x (over 7%). Multi‐junction solar cells with polymers containing nitrogen atoms as the first layer and the mixed PEDOT:PSS and MoO _x nanoparticles as hole extraction layer reach fill factor (FF) of over 60%, and PCE of over 8%, while the identical stack with pristine PEDOT:PSS or MoO _x nanoparticles show FF smaller than 50% and PCE less than 5%.     

Evaporation‐Free Nonfullerene Flexible Organic Solar Cell Modules Manufactured by An All‐Solution Process

To ensure laboratory‐to‐industry transfer of next‐generation energy harvesting organic solar cells (OSCs), it is necessary to develop flexible OSC modules that can be produced on a continuous roll‐to‐roll basis and to apply an all‐solution process. In this study, nonfullerene acceptors (NFAs)‐based donor polymer, SMD2, is newly designed and synthesized to continuously fabricate high‐performance flexible OSC modules. Also, multifunctional hole transport layers (HTLs), WO₃/HTL solar bilayer HTLs, are developed and applied via an all‐solution process called “ProcessOne” into inverted structure. SMD2, the donor terpolymer, has a deep highest occupied molecular orbital (HOMO) level and can achieve a power conversion efficiency (PCE) of 11.3% with NFAs without any pre‐/post‐treatment because of its optimal balance between crystallinity and miscibility. Furthermore, the integration of multifunctional HTLs enables the recovery of the drop in open circuit voltage (V_OC) caused by a mismatch in energy levels between the deep HOMO level of the NFAs‐based bulk‐heterojunction layer and the solution‐processed HTLs. Also, the photostability under ultraviolet‐exposure necessary for “ProcessOne” is greatly improved because of the integration of multifunctional HTLs. Consequently, because of the synergistic effects of these approaches, the flexible OSC modules fabricated in an industrial production line have a PCE of 5.25% (P_max = 419.6 mW) on an active area of 80 cm².     

Scalable Triple Cation Mixed Halide Perovskite–BiVO4 Tandems for Bias‐Free Water Splitting

Strong interest exists in the development of organic–inorganic lead halide perovskite photovoltaics and of photoelectrochemical (PEC) tandem absorber systems for solar fuel production. However, their scalability and durability have long been limiting factors. In this work, it is revealed how both fields can be seamlessly merged together, to obtain scalable, bias‐free solar water splitting tandem devices. For this purpose, state‐of‐the‐art cesium formamidinium methylammonium (CsFAMA) triple cation mixed halide perovskite photovoltaic cells with a nickel oxide (NiO_x) hole transport layer are employed to produce Field's metal‐epoxy encapsulated photocathodes. Their stability (up to 7 h), photocurrent density (–12.1 ± 0.3 mA cm^?2 at 0 V versus reversible hydrogen electrode, RHE), and reproducibility enable a matching combination with robust BiVO₄ photoanodes, resulting in 0.25 cm² PEC tandems with an excellent stability of up to 20 h and a bias‐free solar‐to‐hydrogen efficiency of 0.35 ± 0.14%. The high reliability of the fabrication procedures allows scaling of the devices up to 10 cm², with a slight decrease in bias‐free photocurrent density from 0.39 ± 0.15 to 0.23 ± 0.10 mA cm^?2 due to an increasing series resistance. To characterize these devices, a versatile 3D‐printed PEC cell is also developed.     

Improving Film Formation and Photovoltage of Highly Efficient Inverted‐Type Perovskite Solar Cells through the Incorporation of New Polymeric Hole Selective Layers

Two chemically tailored new conjugated copolymers, HSL1 and HSL2, were developed and applied as hole selective layers to improve the anode interface of fullerene/perovskite planar heterojunction solar cells. The introduction of polar functional groups on the polymer side chains increases the surface energy of the hole selective layers (HSLs), which promote better wetting with the perovskite films and lead to better films with full coverage and high crystallinity. The deep highest occupied molecular orbital levels of the HSLs align well with the valence band of the perovskite semiconductors, resulted in increase photovoltage. The high lying lowest unoccupied molecule orbital level provides sufficient electron blocking ability to prevent electrons from reaching the anode and reduces the interfacial trap‐assisted recombination at the poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate)/perovskite interface, resulting in a longer charge‐recombination lifetime and shorter charge‐extraction time. In the presence of the HSLs, high‐performance CH₃NH₃PbI _x Cl_{3? x} perovskite solar cells with a power conversion efficiency (PCE) of 16.6% (V _oc: 1.07 V) and CH₃NH₃Pb(I_0.3Br_0.7) _x Cl_{3? x} cells with a PCE of 10.3% (V _oc: 1.34 V) can be realized.     

Morphology Controlling of All‐Inorganic Perovskite at Low Temperature for Efficient Rigid and Flexible Solar Cells

All‐inorganic cesium lead halide (CsPbX₃) perovskites have emerged as promising photovoltaic materials owing to their superior thermal stability compared to traditional organic–inorganic hybrid counterparts. However, the CsPbX₃ perovskites generally need to be prepared at high‐temperature, which restricts their application in multilayer or flexible solar cells. Herein, the formation of CsPbX₃ perovskites at room‐temperature (RT) induced by dimethylsulphoxide (DMSO) coordination is reported. It is further found that a RT solvent (DMSO) annealing (RTSA) treatment is valid to control the perovskite crystallization dynamics, leading to uniform and void‐free films, and consequently a maximum power conversion efficiency (PCE) of 6.4% in the device indium tin oxide (ITO)/NiO _x /RT‐CsPbI₂Br/C₆₀/Bathocuproine (BCP)/Ag, which is, as far as it is known, the first report of RT solution‐processed CsPbX₃‐based perovskite solar cells (PSCs). Moreover, the efficiency can be boosted up to 10.4% by postannealing the RTSA‐treated perovskite film at an optimal temperature of 120 °C. Profiting from the moderate temperature, flexible PSCs are also demonstrated with a maximum PCE of 7.3% for the first time. These results may stimulate further development of all‐inorganic CsPbX₃ perovskites and their application in flexible electronics.     

Enhanced Light Harvesting in Perovskite Solar Cells by a Bioinspired Nanostructured Back Electrode

Light management holds great promise of realizing high‐performance perovskite solar cells by improving the sunlight absorption with lower recombination current and thus higher power conversion efficiency (PCE). Here, a convenient and scalable light trapping scheme is demonstrated by incorporating bioinspired moth‐eye nanostructures into the metal back electrode via soft imprinting technique to enhance the light harvesting in organic–inorganic lead halide perovskite solar cells. Compared to the flat reference cell with a methylammonium lead halide perovskite (CH₃NH₃PbI_3?x Cl_x ) absorber, 14.3% of short‐circuit current improvement is achieved for the patterned devices with moth‐eye nanostructures, yielding an increased PCE up to 16.31% without sacrificing the open‐circuit voltage and fill factor. The experimental and theoretical characterizations verify that the cell performance enhancement is mainly ascribed by the broadband polarization‐insensitive light scattering and surface plasmonic effects due to the patterned metal back electrode. It is noteworthy that this light trapping strategy is fully compatible with solution‐processed perovskite solar cells and opens up many opportunities toward the future photovoltaic applications.     

Soft Template‐Controlled Growth of High‐Quality CsPbI3 Films for Efficient and Stable Solar Cells

The unfavorable morphology and inefficient utilization of phase transition reversibility have limited the high‐temperature‐processed inorganic perovskite films in both efficiency and stability. Here, a simple soft template‐controlled growth (STCG) method is reported by introducing (adamantan‐1‐yl)methanammonium to control the nucleation and growth rate of CsPbI₃ crystals, which gives rise to pinhole‐free CsPbI₃ film with a grain size on a micrometer scale. The STCG‐based CsPbI₃ perovskite solar cell exhibits a power conversion efficiency of 16.04% with significantly reduced defect densities and charge recombination. More importantly, an all‐inorganic solar cell with the architecture fluorine‐doped tin oxide (FTO)/NiO_x/STCG‐CsPbI₃/ZnO/indium‐doped tin oxide (ITO) is successfully fabricated to demonstrate its real advantage in thermal stability. By suppressing the inductive effect of defects during the phase transition and utilizing the unique reversibility of the phase transition for the high‐temperature‐processed CsPbI₃ film, the all‐inorganic solar cell retains 90% of its initial efficiency after 3000 h of continuous light soaking and heating.     

Efficient Plastic Perovskite Solar Cell with a Low‐Temperature Processable Electrodeposited TiO2 Compact Layer and a Brookite TiO2 Scaffold

Recent research on fabricating scaffold‐type perovskite solar cells on plastic substrates has reported noteworthy progress in replacing the high‐temperature processing of TiO₂ scaffolds and compact layers with various low‐temperature processes. Herein, recent progress in the laboratory is reported regarding the development of electrodeposited TiO_x compact layers and brookite TiO₂ scaffolds, both of which can be processed under 150 °C without greatly sacrificing their photovoltaic performance. Through systematic characterization of device properties and careful optimization of the fabrication conditions, a record‐high 15.76% power conversion efficiency of a plastic TiO₂ scaffold‐type perovskite solar cell is demonstrated. In addition, bending durability and preliminary stability tests on this plastic perovskite solar cell show promising results and indicate clear directions for future improvement.     

Spatial Distribution Recast for Organic Bulk Heterojunctions for High‐Performance All‐Inorganic Perovskite/Organic Integrated Solar Cells

All‐inorganic CsPbIBr₂ perovskite solar cells (pero‐SCs) exhibit excellent overall stability, but their power conversion efficiencies (PCEs) are greatly limited by their wide bandgaps. Integrated solar cells (ISCs) are considered to be an emergent technology that could extend their photoresponse by directly stacking two distinct photoactive layers with complementary bandgaps. However, rising photocurrents always sacrifice other photovoltaic parameters, thereby leading to an unsatisfactory PCE. Here, a recast strategy is proposed to optimize the spatial distribution components of low‐bandgap organic bulk‐heterojunction (BHJ) film, and is combined with an all‐inorganic perovskite to construct perovskite/BHJ ISCs. With this strategy, the integrated perovskite/BHJ film with a top‐enriched donor‐material spatial distribution is shown to effectively improve ambipolar charge transport behavior and suppress charge carrier recombination. For the first time, the ISC is not only significantly extended and enhanced the photoresponse achieving a 20% increase in current density, but also exhibits a high open‐circuit voltage and fill factor at the same time. As a result, a record PCE of 11.08% based on CsPbIBr₂ pero‐SCs is realized; it simultaneously shows excellent long‐term stability against heat and ultraviolet light.     

Halogen Engineering for Operationally Stable Perovskite Solar Cells via Sequential Deposition

The performance of perovskite solar cells (PSCs) relies on the synthesis method and chemical composition of the perovskite materials. So far, PSCs that have adopted two‐step sequential deposited perovskite with the state‐of‐art composition (FAPbI₃)_1?x(MAPbBr₃)_x (x < 0.05) have achieved record power conversion efficiency (PCE), while their one‐step antisolvent dripping counterparts with typical composition Cs_0.05FA_0.81MA_0.14Pb(I_0.85Br_0.15)₃ with more bromine have exhibited much better long‐term operational stability. Thus, halogen engineering that aims to elevate bromine content in sequential deposited perovskite film would push operational stability of PSCs toward that of antisolvent dripping deposited perovskite materials. Here, a Br‐rich seeding growth method is devised and perovskite seed solution with high bromine content is introduced into a PbI₂ precursor, leading to bromine incorporation in the resulting perovskite film. Photovoltaic devices fabricated by Br‐rich seeding growth method exhibit a PCE of 21.5%, similar to 21.6% for PSCs having lower bromine content. Whereas, the operational stability of PSCs with higher bromine content is significantly enhanced, with over 80% of initial PCE retained after 500 h tracking at maximum power point under 1‐sun illumination. This work highlights the vital importance of halogen composition for the operational stability of PSCs, and introduces an effective way to incorporate bromine into mixed‐cation‐halide perovskite film via sequential deposition method.     

Modified PEDOT Layer Makes a 1.52 V Voc for Perovskite/PCBM Solar Cells

The work functions for charge transport layers in perovskite solar cells affect device performance significantly. In this work, the regular poly(3,4‐ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) is modified by adding a polymer electrolyte PSS‐Na to improve its HTL function in perovskite solar cells. The modified PEDOT:PSS films (called m‐PEDOT:PSS) possess higher work function than the regular one. Its energy level matches the valence band of perovskite very well, leading to enhanced V_oc and PCE (power conversion efficiency). When CH₃NH₃PbI₃ is used as the light absorber, the cell with PEDOT:PSS HTL gives a V_oc of 0.96 V and a PCE of 12.35%, while the cell with m‐PEDOT:PSS layer gives a V_oc of 1.11 V and a PCE of 15.56%. Enhanced V_oc and PCE are also achieved when CH₃NH₃PbI₂Br or CH₃NH₃PbBr₃ is used as the light absorber. The m‐PEDOT:PSS/CH₃NH₃PbBr₃/PC₆₁BM solar cells demonstrate an outstanding V_oc of 1.52 V.     

Greatly Reduced Processing Temperature for a Solution‐Processed NiOx Buffer Layer in Polymer Solar Cells

By application of thermal annealing and UV ozone simultaneously, a solution‐processed NiO_x film can achieve a work function of approximately –5.1 eV at a temperature below 150 °C, which allows the processing of NiO_x that is compatible with fabrication of polymer solar cells (PSCs) on plastic substrates. The low processing temperature, which is greatly reduced from 250–400 °C to 150 °C, is attributed to the high concentration of NiOOH species on the film surface. This concentration will result in a large surface dipole and lead to increased work function. The pretreated NiO_x is demonstrated to be an efficient buffer layer in PSCs based on polymers with different highest occupied molecular orbital energy levels. Compared with conventional poly(3,4‐ethylenedioxy‐thiophene):poly(styrenesulfonate)‐buffered PSCs, the NiO_x‐buffered PSCs achieve similar or improved device performance as well as enhanced device stability.     

Enhanced Efficiency in Plastic Solar Cells via Energy Matched Solution Processed NiOx Interlayers

We show enhanced efficiency and stability of a high performance organic solar cell (OPV) when the work‐function of the hole collecting indium‐tin oxide (ITO) contact, modified with a solution‐processed nickel oxide (NiO_x) hole‐transport layer (HTL), is matched to the ionization potential of the donor material in a bulk‐heterojunction solar cell. Addition of the NiO_x HTL to the hole collecting contact results in a power conversion efficiency (PCE) of 6.7%, which is a 17.3% net increase in performance over the 5.7% PCE achieved with a poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) HTL on ITO. The impact of these NiO_x films is evaluated through optical and electronic measurements as well as device modeling. The valence and conduction band energies for the NiO_x HTL are characterized in detail through photoelectron spectroscopy studies while spectroscopic ellipsometry is used to characterize the optical properties. Oxygen plasma treatment of the NiO_x HTL is shown to provide superior contact properties by increasing the ITO/NiO_x contact work‐function by 500 meV. Enhancement of device performance is attributed to reduction of the band edge energy offset at the ITO/NiO_x interface with the poly(N‐9′‐heptadecanyl‐2,7‐carbazole‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothidiazole) (PCDTBT):[6,6]‐phenyl‐C61 butyric acid methyl ester PCBM and [6,6]‐phenyl‐C71 butyric acid methyl ester (PC₇₀BM) active layer. A high work‐function hole collecting contact is therefore the appropriate choice for high ionization potential donor materials in order to maximize OPV performance.     

Efficient and Highly Air Stable Planar Inverted Perovskite Solar Cells with Reduced Graphene Oxide Doped PCBM Electron Transporting Layer

Reduced graphene oxide (rGO) is added in the [6,6]‐Phenyl‐C61‐butyric acid methyl ester (PCBM) electron transport layer (ETL) of planar inverted perovskite solar cells (PSCs), resulting in a power conversion efficiency (PCE) improvement of ≈12%, with a hysteresis‐free PCE of 14.5%, compared to 12.9% for the pristine PCBM based device. The universality of the method is demonstrated in PSCs based on CH₃NH₃PbI_3?x Cl_x and CH₃NH₃PbI₃ perovskites, deposited through one step and two step spin coating process, respectively. After a comprehensive spectroscopic characterization of both devices, it is clear that the introduction of rGO in PCBM ETL results in an important increase of the ETL conductivity, together with reduced series resistance and surface roughness. As a result, a significant photoluminescence quenching of such perovskite/ETL is observed, confirming the increased measured short circuit current density. Transient absorption measurements reveal that in the rGO‐based device, the relaxation process of the excited electrons is significantly faster compared to the reference, which implies that the charge injection rate is significantly faster for the first. Furthermore, the light soaking effect is significantly reduced. Finally, aging measurements reveal that the rGO stabilizes the ELT/perovskite interface, which results in the stabilization of perovskite crystal structure after prolonged illumination.     

Enhancing Optical,Electronic, Crystalline,and Morphological Properties of Cesium Lead Halide by Mn Substitution for High‐Stability All‐Inorganic Perovskite Solar Cells with Carbon Electrodes

In this work all‐inorganic perovskite CsPbIBr₂ are doped with Mn to compensate their shortcomings in band structure for the application of perovskite solar cells (PSCs). The novel Mn‐doped all‐inorganic perovskites, CsPb_1?xMn_xI_1+2xBr_2?2x, are prepared in ambient atmosphere. As the concentration of Mn²⁺ ions increases, the bandgaps of CsPb_1?xMn_xI_1+2xBr_2?2x decrease from 1.89 to 1.75 eV. Additionally, when the concentration of Mn dopants is appropriate, this novel Mn‐doped all‐inorganic perovskite film shows better crystallinity and morphology than its undoped counterpart. These advantages alleviate the energy loss in hole transfer and facilitate the charge‐transfer in perovskites, therefore, PSCs based on these novel CsPb_1?xMn_xI_1+2xBr_2?2x perovskite films display better photovoltaic performance than the undoped CsPbIBr₂ perovskite films. The reference CsPbIBr₂ cell reaches a power conversion efficiency (PCE) of 6.14%, comparable with the previous reports. The CsPb_1?xMn_xI_1+2xBr_2?2x cells reach the highest PCE of 7.36% (when x = 0.005), an increase of 19.9% in PCE. Furthermore, the encapsulated CsPb_0.995Mn_0.005I_1.01Br_1.99 cells exhibit good stability in ambient atmosphere. The storage stability measurements on the encapsulated PSCs reveal that PCE is dropped by only 8% of the initial value after >300 h in ambient. Such improved efficiency and stability are achieved using low‐cost carbon electrodes (without expensive hole transport materials and Au electrodes).