Stable Lithium Electrodeposition at Ultra‐High Current Densities Enabled by 3D PMF/Li Composite Anode

Lithium metal batteries (LMBs) are promising candidates for next‐generation energy storage due to their high energy densities on both weight and volume bases. However, LMBs usually undergo uncontrollable lithium deposition, unstable solid electrolyte interphase, and volume expansion, which easily lead to low Coulombic efficiency, poor cycling performance, and even safety hazards, hindering their practical applications for more than forty years. These issues can be further exacerbated if operated at high current densities. Here a stable lithium metal battery enabled by 3D porous poly‐melamine‐formaldehyde (PMF)/Li composite anode is reported. PMF with a large number of polar groups (amine and triazine) can effectively homogenize Li‐ion concentration when these ions approach to the anode surface and thus achieve uniform Li deposition. Moreover, the 3D structured anode can serve as a Li host to mitigate the volume change during Li stripping and plating process. Galvanostatic measurements demonstrate that the 3D composite electrode can achieve high‐lithium Coulombic efficiency of 94.7% at an ultrahigh current density of 10 mA cm^?2 after 50 cycles with low hysteresis and smooth voltage plateaus. When coupled with Li₄Ti₅O₁₂, half‐cells show enhanced rate capabilities and Coulombic efficiencies, opening great opportunities for high‐energy batteries.     

Highly Stable Operation of Lithium Metal Batteries Enabled by the Formation of a Transient High‐Concentration Electrolyte Layer

Lithium (Li) metal has been extensively investigated as an anode for rechargeable battery applications due to its ultrahigh theoretical specific capacity and the lowest redox potential. However, significant challenges including dendrite growth and low Coulombic efficiency are still hindering the practical applications of rechargeable Li metal batteries. It is demonstrated that long‐term cycling of Li metal batteries can be realized by the formation of a transient high‐concentration electrolyte layer near the surface of Li metal anode during high rate discharge process. The highly concentrated Li⁺ ions in this transient layer will immediately be solvated by the available solvent molecules and facilitate the formation of a stable and flexible solid electrolyte interphase (SEI) layer composed of a poly(ethylene carbonate) framework integrated with other organic/inorganic lithium salts. This SEI layer largely suppresses the corrosion of Li metal anode attacked by free organic solvents and enables the long‐term operation of Li metal batteries. The fundamental findings in this work provide a new direction for the development of Li metal batteries that could be operated at high current densities for a wide range of applications.     

A Coaxial‐Interweaved Hybrid Lithium Metal Anode for Long‐Lifespan Lithium Metal Batteries

Lithium (Li) metal is one of the most promising anode materials to construct next‐generation rechargeable batteries owing to its ultrahigh theoretical capacity and the lowest electrochemical potential. Unfortunately, practical application of Li metal batteries is severely hindered by short lifespan and safety concerns caused by Li dendrite growth during cycling. Herein, a coaxial‐interweaved hybrid Li metal anode is proposed for dendrite inhibition that significantly improves the cycling stability of Li metal batteries. The hybrid Li metal anode is fabricated by Li composition into a 3D interweaved scaffold, where each fiber of the interwoven scaffold is composed of a conductive skeleton and a coaxial lithiophilic layer modified on the surface. The coaxial‐interweaved structure endows the hybrid anode with favored Li affinity to guide uniform Li deposition, sufficient channels for ion transportation and electron conduction, and enhanced stability during Li plating and stripping. Consequently, the hybrid Li metal anode affords high Coulombic efficiency over 98.5% for 750 cycles with dendrite‐free morphologies in half cells and improved capacity retention of 80.1% after 100 cycles in LiFePO₄ full cells. The innovative coaxial‐interweaved hybrid Li metal anode demonstrates multiscale design strategy from lithiophilic modification to scaffold construction and promises the prospect of Li metal batteries for future applications.     

Plating/Stripping Behavior of Actual Lithium Metal Anode

Lithium (Li) metal anodes exhibits the potential to enable rechargeable Li batteries with a high energy density. However, the irreversible plating and stripping behaviors of Li metal anodes with high reactivity and dendrite growth when matching different cathodes in working cells are not fully understood yet. Herein the working manner of very thin Li metal anodes (50 µm, 10 mAh cm^?2) is probed with different sequences of Li plating and stripping at 3.0 mA cm^?2 and 3.0 mAh cm^?2. Dendrite growth and dead Li forms on the surface of the initially plated Li electrode (P‐Li), while Li dendrites form in the pit of the initially stripped Li electrode (S‐Li). This induces the differences in reactive sites, distribution of dead Li, and voltage polarization of Li metal anodes. There is a gap of 15–20 and 13–16 mV for the end voltages between S‐Li and P‐Li during stripping and plating, respectively. When matching LiFePO₄ and FePO₄ cathodes, P‐Li | LiFePO₄ cells exhibit a 30‐cycle longer lifespan with smaller end polarization due to differences in the sequences of Li plating and stripping. This contribution affords emerging working principles for actual Li metal anodes when matching lithium‐containing and lithium‐free cathodes.     

Polymer‐in‐“Quasi‐Ionic Liquid” Electrolytes for High‐Voltage Lithium Metal Batteries

Due to the limited oxidation stability (<4 V) of ether oxygen in its polymer structure, polyethylene oxide (PEO)‐based polymer electrolytes are not compatible with high‐voltage (>4 V) cathodes, thus hinder further increases in the energy density of lithium (Li) metal batteries (LMBs). Here, a new type of polymer‐in‐“quasi‐ionic liquid” electrolyte is designed, which reduces the electron density on ethereal oxygens in PEO and ether solvent molecules, induces the formation of stable interfacial layers on both surfaces of the LiNi_1/3Mn_1/3Co_1/3O₂ (NMC) cathode and the Li metal anode in Li||NMC batteries, and results in a capacity retention of 88.4%, 86.7%, and 79.2% after 300 cycles with a charge cutoff voltage of 4.2, 4.3, and 4.4 V for the LMBs, respectively. Therefore, the use of “quasi‐ionic liquids” is a promising approach to design new polymer electrolytes for high‐voltage and high‐specific‐energy LMBs.     

Cross Talk between Transition Metal Cathode and Li Metal Anode: Unraveling Its Influence on the Deposition/Dissolution Behavior and Morphology of Lithium

Lithium metal batteries (LMBs) combining a Li metal anode with a transition metal (TM) cathode can achieve higher practical energy densities (Wh L^?1) than Li/S or Li/O₂ cells. Research for improving the electrochemical behavior of the Li metal anode by, for example, modifying the liquid electrolyte is often conducted in symmetrical Li/Li or Li/Cu cells. This study now demonstrates the influence of the TM cathode on the Li metal anode, thus full cell behavior is analyzed in a way not considered so far in research with LMBs. Therefore, the deposition/dissolution behavior of Li metal and the resulting morphology is investigated with three different cathode materials (LiNi_0.5Mn_1.5O₄, LiNi_0.6Mn_0.2Co_0.2O₂, and LiFePO₄) by post mortem analysis with a scanning electron microscope. The observed large differences of the Li metal morphology are ascribed to the dissolution and crossover of TMs found deposited on Li metal and in the electrolyte by X‐ray photoelectron spectroscopy, energy‐dispersive X‐ray spectroscopy, and total reflection X‐ray fluorescence analysis. To support this correlation, the TM dissolution is simulated by adding Mn salt to the electrolyte. This study offers new insights into the cross talk between the Li metal anodes and TM cathodes, which is essential, when investigating Li metal electrodes for LMB full cells.     

Eliminating Dendrites through Dynamically Engineering the Forces Applied during Li Deposition for Stable Lithium Metal Anodes

Lithium metal anodes are considered the most promising anode for next‐generation high‐energy‐density batteries due to their high theoretical capacity and low electrochemical potential. However, intractable barriers, especially the notorious dendrite growth, severe volume expansion, and side reactions, have obstructed its large‐scale application. Numerous strategies from different points of view are explored to surmount these obstacles. Within these efforts, dynamically engineering the forces applied during the electrochemical process plays a significant role, as they can potentially eliminate the dendrite growth. In this Research News article, the relationship between different kinds of forces and the behavior of Li⁺/Li during the lithium deposition process is first explicated. Advanced strategies in building dendrite‐free Li anodes through dynamically engineering these forces are also summarized by sorting the Li deposition process into three stages: Li⁺ transport in electrolyte, Li⁺ reduction/Li atom surface migration, and Li bulk diffusion. Future perspectives and promising research directions for dendrite control are finally proposed. It is expected that dynamically engineering the forces applied during Li deposition will pave the way for next‐generation high‐energy‐density rechargeable Li metal batteries.     

Electrokinetic Phenomena Enhanced Lithium‐Ion Transport in Leaky Film for Stable Lithium Metal Anodes

The application of lithium (Li) metal anodes in Li metal batteries has been hindered by growth of Li dendrites, which lead to short cycling life. Here a Li‐ion‐affinity leaky film as a protection layer is reported to promote a dendrite‐free Li metal anode. The leaky film induces electrokinetic phenomena to enhance Li‐ion transport, leading to a reduced Li‐ion concentration polarization and homogeneous Li‐ion distribution. As a result, the dendrite‐free Li metal anode during Li plating/stripping is demonstrated even at an extremely high deposition capacity (6 mAh cm^?2) and current density (40 mA cm^?2) with improved Coulombic efficiencies. A full cell battery with the leaky‐film protected Li metal as the anode and high‐areal‐capacity LiNi_0.8Co_0.1Mn_0.1O₂ (NCM‐811) (≈4.2 mAh cm^?2) or LiFePO₄ (≈3.8 mAh cm^?2) as the cathode shows improved cycling stability and capacity retention, even at lean electrolyte conditions.     

Zipper‐Inspired SEI Film for Remarkably Enhancing the Stability of Li Metal Anode via Nucleation Barriers Controlled Weaving of Lithium Pits

The lithium dendrite, inducing short circuit and breaking solid electrolyte interphase (SEI) films, is deleterious to the stability of Li metal batteries due to the uncontrollable occurrence of miscellaneous stresses. In contrast to conventional suppression routes, herein a strategy is proposed via controlling SEI film broken regions to minimize releasing stress in terms of weaving lithium pits. Inspired by the principle of zippers, zipper‐like SEI films enable offering ordered pattern on the surface of Li anode via mechanical rolling. For the available cells, net‐like sewing/breaking patterns alternatively occur in Li plating/stripping. In the same electrolyte, a stable and dendrite‐free Li homogeneous growth is achieved.     

Mixed Ion and Electron‐Conducting Scaffolds for High‐Rate Lithium Metal Anodes

Li metal batteries are considered a promising candidate for next‐generation rechargeable batteries. However, the practical application of Li metal batteries has been hindered by many challenges, especially the cycling stability of Li anodes due to their uncontrollable dendrite growth, volume fluctuation, and side reactions. These problems are more severe under high‐rate charge/discharge process. Therefore, the realization of stable cycling of Li anodes under high current density is crucial for the practical application of Li metal batteries. In this Progress Report, the authors focus on the stability of metallic Li through interphase design or microstructure construction. The advantages and drawbacks of the first‐generation 3D scaffolds are summarized, and a review of recent research progress in this area is generated. As high‐rate cycling of metallic Li is a complex dynamic problem, a scaffold with high mixed ionic and electronic conductivity may be a promising approach. The different design strategies of mixed ion and electron‐conductive scaffolds working with liquid and solid electrolytes are discussed, along with their technical challenges. Further directions of mixed ion and electron‐conductive scaffolds are also proposed.     

In Situ NMR Verification for Stacking Pressure-Induced Lithium Deposition and Dead Lithium in Anode-Free Lithium Metal Batteries

Anode-free lithium metal batteries have emerged as strong contenders for next-generation rechargeable batteries due to their ultra-high energy density. However, their safety and life span are insufficient because of the easy generation of dendrites and dead lithium during lithium plating and stripping. Understanding the formation mechanism for lithium dendrites and dead lithium is essential to further improve battery performance. By employing in situ solid-state nuclear magnetic resonance (NMR) spectroscopy, the influence of stacking pressure on dendritic behavior and dead lithium is systematically investigated. At 0.1 MPa, lithium dendrite is rapidly formed, followed by a linear increase of dead lithium. High stacking pressure not only causes lithium metal to fracture but also leads to form dendrites and dead lithium at the fracture site. At 0.5 MPa stacking pressure, the least quantity of dead lithium is attained, and the growth pattern of dead lithium is exponential growth. The exponential growth pattern is distinguished by the high growth of dead lithium early in the battery cycle and essentially no growth later in the cycle. As a result, it is believed that efficient suppression of dead lithium generation early in battery cycling can play a critical role in improving battery performance.     

Countersolvent Electrolytes for Lithium‐Metal Batteries

Development of electrolytes that simultaneously have high ionic conductivity, wide electrochemical window, and lithium dendrite suppression ability is urgently required for high‐energy lithium‐metal batteries (LMBs). Herein, an electrolyte is designed by adding a countersolvent into LiFSI/DMC (lithium bis(fluorosulfonyl)amide/dimethyl carbonate) electrolytes, forming countersolvent electrolytes, in which the countersolvent is immiscible with the salt but miscible with the carbonate solvents. The solvation structure and unique properties of the countersolvent electrolyte are investigated by combining electroanalytical technology with a Molecular Dynamics simulation. Introducing the countersolvent alters the coordination shell of Li⁺ cations and enhances the interaction between Li⁺ cations and FSI^? anions, which leads to the formation of a LiF‐rich solid electrolyte interphase, arising from the preferential reduction of FSI^? anions. Notably, the countersolvent electrolyte suppresses Li dendrites and enables stable cycling performance of a Li||NCM622 battery at a high cut‐off voltage of 4.6 V at both 25 and 60 °C. This study provides an avenue to understand and design electrolytes for high‐energy LMBs in the future.     

An Interconnected Channel‐Like Framework as Host for Lithium Metal Composite Anodes

Lithium (Li) metal anodes have long been counted on to meet the increasing demand for high energy, high‐power rechargeable battery systems but they have been plagued by uncontrollable plating, unstable solid electrolyte interphase (SEI) formation, and the resulting low Coulombic efficiency. These problems are even aggravated under commercial levels of current density and areal capacity testing conditions. In this work, the channel‐like structure of a carbonized eggplant (EP) as a stable “host” for Li metal melt infusion, is utilized. With further interphase modification of lithium fluoride (LiF), the as‐formed EP–LiF composite anode maintains ≈90% Li metal theoretical capacity and can successfully suppress dendrite growth and volume fluctuation during cycling. EP–LiF offers much improved symmetric cell and full‐cell cycling performance with lower and more stable overpotential under various areal capacity and elevated rate capability. Furthermore, carbonized EP serves as a light‐weight high‐performance current collector, achieving an average Coulombic efficiency ≈99.1% in ether‐based electrolytes with 2.2 mAh cm^?2 cycling areal capacity. The natural structure of carbonized EP will inspire further artificial designs of electrode frameworks for both Li anode and sulfur cathodes, enabling promising candidates for next‐generation high‐energy density batteries.     

Tailoring Lithium Deposition via an SEI‐Functionalized Membrane Derived from LiF Decorated Layered Carbon Structure

Lithium (Li) metal is a key anode material for constructing next generation high energy density batteries. However, dendritic Li deposition and unstable solid electrolyte interphase (SEI) layers still prevent practical application of Li metal anodes. In this work, it is demonstrated that an uniform Li coating can be achieved in a lithium fluoride (LiF) decorated layered structure of stacked graphene (SG), leading to the formation of an SEI‐functionalized membrane that retards electron transfer by three orders of magnitude to avoid undesirable Li deposition on the top surface, and ameliorates Li⁺ ion migration to enable uniform and dendrite‐free Li deposition beneath such an interlayer. Surface chemistry analysis and density functional theory calculations demonstrate that these beneficial features arise from the formation of C–F_x surface components on the SG sheets during the Li coating process. Based on such an SEI‐functionalized membrane, stable cycling at high current densities up to 3 mA cm^?2 and Li plating capacities up to 4 mAh cm^?2 can be realized in LiPF₆/carbonate electrolytes. This work elucidates the promising strategy of modifying Li plating behavior through the SEI‐functionalized carbon structure, with significantly improved cycling stability of rechargeable Li metal anodes.