An Ion‐Exchange Promoted Phase Transition in a Li‐Excess Layered Cathode Material for High‐Performance Lithium Ion Batteries

A new approach to intentionally induce phase transition of Li‐excess layered cathode materials for high‐performance lithium ion batteries is reported. In high contrast to the limited layered‐to‐spinel phase transformation that occurred during in situ electrochemical cycles, a Li‐excess layered Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ is completely converted to a Li₄Mn₅O₁₂‐type spinel product via ex situ ion‐exchanges and a post‐annealing process. Such a layered‐to‐spinel phase conversion is examined using in situ X‐ray diffraction and in situ high‐resolution transmission electron microscopy. It is found that generation of sufficient lithium ion vacancies within the Li‐excess layered oxide plays a critical role for realizing a complete phase transition. The newly formed spinel material exhibits initial discharge capacities of 313.6, 267.2, 204.0, and 126.3 mAh g^?1 when cycled at 0.1, 0.5, 1, and 5 C (1 C = 250 mA g^?1), respectively, and can retain a specific capacity of 197.5 mAh g^?1 at 1 C after 100 electrochemical cycles, demonstrating remarkably improved rate capability and cycling stability in comparison with the original Li‐excess layered cathode materials. This work sheds light on fundamental understanding of phase transitions within Li‐excess layered oxides. It also provides a novel route for tailoring electrochemical performance of Li‐excess layered cathode materials for high‐capacity lithium ion batteries.     

Radially Oriented Single‐Crystal Primary Nanosheets Enable Ultrahigh Rate and Cycling Properties of LiNi0.8Co0.1Mn0.1O2 Cathode Material for Lithium‐Ion Batteries

Ni‐rich Li[Ni_xCo_yMn_1?x?y]O₂ (x ≥ 0.8) layered oxides are the most promising cathode materials for lithium‐ion batteries due to their high reversible capacity of over 200 mAh g^?1. Unfortunately, the anisotropic properties associated with the α‐NaFeO₂ structured crystal grains result in poor rate capability and insufficient cycle life. To address these issues, a micrometer‐sized Ni‐rich LiNi_0.8Co_0.1Mn_0.1O₂ secondary cathode material consisting of radially aligned single‐crystal primary particles is proposed and synthesized. Concomitant with this unique crystallographic texture, all the exposed surfaces are active {010} facets, and 3D Li⁺ ion diffusion channels penetrate straightforwardly from surface to center, remarkably improving the Li⁺ diffusion coefficient. Moreover, coordinated charge–discharge volume change upon cycling is achieved by the consistent crystal orientation, significantly alleviating the volume‐change‐induced intergrain stress. Accordingly, this material delivers superior reversible capacity (203.4 mAh g^?1 at 3.0–4.3 V) and rate capability (152.7 mAh g^?1 at a current density of 1000 mA g^?1). Further, this structure demonstrates excellent cycling stability without any degradation after 300 cycles. The anisotropic morphology modulation provides a simple, efficient, and scalable way to boost the performance and applicability of Ni‐rich layered oxide cathode materials.     

Direct Growth of Flower‐Like δ‐MnO2 on Three‐Dimensional Graphene for High‐Performance Rechargeable Li‐O2 Batteries

A challenge still remains to develop high‐performance and cost‐effective air electrode for Li‐O₂ batteries with high capacity, enhanced rate capability and long cycle life (100 times or above) despite recent advances in this field. In this work, a new design of binder‐free air electrode composed of three‐dimensional (3D) graphene (G) and flower‐like δ‐MnO₂ (3D‐G‐MnO₂) has been proposed. In this design, graphene and δ‐MnO₂ grow directly on the skeleton of Ni foam that inherits the interconnected 3D scaffold of Ni foam. Li‐O₂ batteries with 3D‐G‐MnO₂ electrode can yield a high discharge capacity of 3660 mAh g^?1 at 0.083 mA cm^?2. The battery can sustain 132 cycles at a capacity of 492 mAh g^?1 (1000 mAh g_carbon ^?1) with low overpotentials under a high current density of 0.333 mA cm^?2. A high average energy density of 1350 Wh Kg^?1 is maintained over 110 cycles at this high current density. The excellent catalytic activity of 3D‐G‐MnO₂ makes it an attractive air electrode for high‐performance Li‐O₂ batteries.     

Ni‐Rich/Co‐Poor Layered Cathode for Automotive Li‐Ion Batteries: Promises and Challenges

To pursue a higher energy density (>300 Wh kg^?1 at the cell level) and a lower cost (<$125 kWh^?1 expected at 2022) of Li‐ion batteries for making electric vehicles (EVs) long range and cost‐competitive with internal combustion engine vehicles, developing Ni‐rich/Co‐poor layered cathode (LiNi_1?x?yCo_xMn_yO₂, x+y ≤ 0.2) is currently one of the most promising strategies because high Ni content is beneficial to high capacity (>200 mAh g^?1) while low Co content is favorable to minimize battery cost. Unfortunately, Ni‐rich cathodes suffer from limited structure stability and electrode/electrolyte interface stability in the charged state, leading to electrode degradation and poor cycling performance. To address these problems, various strategies have been employed such as doping, structural optimization design (e.g., core–shell structure, concentration‐gradient structure, etc.), and surface coating. In this review, five key aspects of Ni‐rich/Co‐poor layered cathode materials are explored: energy density, fast charge capability, service life including cycling life and calendar life, cost and element resources, and safety. This enables a comprehensive analysis of current research advances and challenges from the perspective of both academy and industry to help facilitate practical applications for EVs in the future.     

A New Spinel‐Layered Li‐Rich Microsphere as a High‐Rate Cathode Material for Li‐Ion Batteries

Li‐rich layered materials are considered to be the promising low‐cost cathodes for lithium‐ion batteries but they suffer from poor rate capability despite of efforts toward surface coating or foreign dopings. Here, spinel‐layered Li‐rich Li‐Mn‐Co‐O microspheres are reported as a new high‐rate cathode material for Li‐ion batteries. The synthetic procedure is relatively simple, involving the formation of uniform carbonate precursor under solvothermal conditions and its subsequent transformation to an assembled microsphere that integrates a spinel‐like component with a layered component by a heat treatment. When calcined at 700 °C, the amount of transition metal Mn and Co in the Li‐Mn‐Co‐O microspheres maintained is similar to at 800 °C, while the structures of constituent particles partially transform from 2D to 3D channels. As a consequence, when tested as a cathode for lithium‐ion batteries, the spinel‐layered Li‐rich Li‐Mn‐Co‐O microspheres obtained at 700 °C show a maximum discharge capacity of 185.1 mA h g^?1 at a very high current density of 1200 mA g^?1 between 2.0 and 4.6 V. Such a capacity is among the highest reported to date at high charge‐discharge rates. Therefore, the present spinel‐layered Li‐rich Li‐Mn‐Co‐O microspheres represent an attractive alternative to high‐rate electrode materials for lithium‐ion batteries.     

Controlled Oxygen Redox for Excellent Power Capability in Layered Sodium‐Based Compounds

A high‐rate of oxygen redox assisted by cobalt in layered sodium‐based compounds is achieved. The rationally designed Na_0.6[Mg_0.2Mn_0.6Co_0.2]O₂ exhibits outstanding electrode performance, delivering a discharge capacity of 214 mAh g^?1 (26 mA g^?1) with capacity retention of 87% after 100 cycles. High rate performance is also achieved at 7C (1.82 A g^?1) with a capacity of 107 mAh g^?1. Surprisingly, the Na_0.6[Mg_0.2Mn_0.6Co_0.2]O₂ compound is able to deliver capacity for 1000 cycles at 5C (at 1.3 A g^?1), retaining 72% of its initial capacity of 108 mAh g^?1. X‐ray absorption spectroscopy analysis of the O K‐edge indicates the oxygen‐redox species (O^2?/1?) is active during cycling. First‐principles calculations show that the addition of Co reduces the bandgap energy from ≈2.65 to ≈0.61 eV and that overlapping of the Co 3d and O 2p orbitals facilitates facile electron transfer, enabling the long‐term reversibility of the oxygen redox, even at high rates. To the best of the authors' knowledge, this is the first report on high‐rate oxygen redox in sodium‐based cathode materials, and it is believed that the findings will open a new pathway for the use of oxygen‐redox‐based materials for sodium‐ion batteries.     

Stable Carbon–Selenium Bonds for Enhanced Performance in Tremella‐Like 2D Chalcogenide Battery Anode

2D cobalt selenide based on conversion reaction has attracted much attention due to its open layered structure and high specific capacity. However, effectively suppressing the fast capacity fade caused by the irreversible Se dissolution and serious volume change during the cycling process is still a challenge. Herein, the concentration of dispersion liquid under supercritical conditions is tuned to induce the CoSe crystal to grow along the graphene oxide (GO), and finally obtain the Tremella‐like CoSe–reduced GO (rGO) hybrid. The nature of epitaxial growth leads to the formation of stable C? Se bonds, which maintain a favorable conductive connection between CoSe and rGO as well as enhance the mechanical strength of active materials to suppress Se dissolution and volume expansion during Na/Li intercalation and deintercalation. The unique microstructural merits of the hybrid result in superior sodium/lithium storage performance (400.8 mAh g^?1 at 1 A g^?1 after 100 cycles for sodium‐ion batteries and 769.6 mAh g^?1 at 2 A g^?1 after 500 cycles for lithium‐ion batteries). Moreover, the transmission X‐ray microscopy technique is first used to directly observe the Se segregation in cobalt selenide and it being suppressed by the C? Se bonds.     

Grafting Benzenediazonium Tetrafluoroborate onto LiNixCoyMnzO2 Materials Achieves Subzero‐Temperature High‐Capacity Lithium‐Ion Storage via a Diazonium Soft‐Chemistry Method

Subzero‐temperature Li‐ion batteries (LIBs) are highly important for specific energy storage applications. Although the nickel‐rich layered lithium transition metal oxides(LiNi_xCo_yMn_zO₂) (LNCM) (x > 0.5, x + y +z = 1) are promising cathode materials for LIBs, their very slow Li‐ion diffusion is a main hurdle on the way to achieve high‐performance subzero‐temperature LIBs. Here, a class of low‐temperature organic/inorganic hybrid cathode materials for LIBs, prepared by grafting a conducting polymer coating on the surface of 3 µm sized LiNi_0.6Co_0.2Mn_0.2O₂ (LNCM‐3) material particles via a greener diazonium soft‐chemistry method is reported. Specifically, LNCM‐3 particles are uniformly coated with a thin polyphenylene film via the spontaneous reaction between LNCM‐3 and C₆H₅N₂⁺BF₄^?. Compared with the uncoated one, the polyphenylene‐coated LNCM‐3 (polyphenylene/LNCM‐3) has shown much improved low‐temperature discharge capacity (≈148 mAh g^?1 at 0.1 C, ?20 °C), outstanding rate capability (≈105 mAh g^?1 at 1 C, ?20 °C), and superior low‐temperature long‐term cycling stability (capacity retention is up to 90% at 0.5 C over 1150 cycles). The low‐temperature performance of polyphenylene/LNCM‐3 is the best among the reported state‐of‐the art cathode materials for LIBs. The present strategy opens up a new avenue to construct advanced cathode materials for wider range applications.     

A Versatile Pyramidal Hauerite Anode in Congeniality Diglyme‐Based Electrolytes for Boosting Performance of Li‐ and Na‐Ion Batteries

For the first time, environmentally friendly sulfur‐rich pyramidal MnS₂ synthesized via a single‐step hydrothermal process is used as a high‐performance anode material in Li‐ion and Na‐ion batteries. The superior electrochemical performance of the MnS₂ electrode along with its high compatibility with ether‐based electrolytes are analyzed in both half‐ and full‐cell configurations. The reversible capacities of ≈84 mAh g^?1 and ≈74 mAh g^?1 at a current density of 50 mA g^?1 are retained in the Li‐ion and Na‐ion full‐cells, respectively, over 200 cycles with excellent capacity retentions. Moreover, important findings regarding activation processes in the presence of a new phase transition and protective electrolyte interphase layer are revealed using ab initio density function theory calculation and in situ potentio‐electrochemical impedance spectroscopy. The detailed complex redox mechanism of MnS₂ in Li/Na half‐cells is also elucidated by ex situ X‐ray photoelectron spectroscopy.     

A Hollow‐Shell Structured V2O5 Electrode‐Based Symmetric Full Li‐Ion Battery with Highest Capacity

The symmetric batteries with an electrode material possessing dual cathodic and anodic properties are regarded as an ideal battery configuration because of their distinctive advantages over the asymmetric batteries in terms of fabrication process, cost, and safety concerns. However, the development of high‐performance symmetric batteries is highly challenging due to the limited availability of suitable symmetric electrode materials with such properties of highly reversible capacity. Herein, a triple‐hollow‐shell structured V₂O₅ (THS‐V₂O₅) symmetric electrode material with a reversible capacity of >400 mAh g^?1 between 1.5 and 4.0 V and >600 mAh g^?1 between 0.1 and 3.0 V, respectively, when used as the cathode and anode, is reported. The THS‐V₂O₅ electrodes assembled symmetric full lithium‐ion battery (LIB) exhibits a reversible capacity of ≈290 mAh g^?1 between 2 and 4.0 V, the best performed symmetric energy storage systems reported to date. The unique triple‐shell structured electrode makes the symmetric LIB possessing very high initial coulombic efficiency (94.2%), outstanding cycling stability (with 94% capacity retained after 1000 cycles), and excellent rate performance (over 140 mAh g^?1 at 1000 mA g^?1). The demonstrated approach in this work leaps forward the symmetric LIB performance and paves a way to develop high‐performance symmetric battery electrode materials.     

Synthesis and Characterization of High‐Energy,High‐Power Spinel‐Layered Composite Cathode Materials for Lithium‐Ion Batteries

Spinel‐layered composites, where a high‐voltage spinel is incorporated in a layered lithium‐rich (Li‐rich) cathode material with a nominal composition x{0.6Li₂MnO₃ · 0.4[LiCo_0.333Mn_0.333Ni_0.333]O₂} · (1 – x) Li[Ni_0.5Mn_1.5]O₄ (x = 0, 0.3, 0.5, 0.7, 1) are synthesized via a hydroxide assisted coprecipitation route to generate high‐energy, high‐power cathode materials for Li‐ion batteries. X‐ray diffraction patterns and the cyclic voltammetry investigations confirm the presence of both the parent components in the composites. The electrochemical investigations performed within a wide potential window show an increased structural stability of the spinel component when incorporated into the composite environment. All the composite materials exhibit initial discharge capacities >200 mAh g^–1. The compositions with x = 0.5 and 0.7 show excellent cycling stability among the investigated materials. Moreover, the first cycle Coulombic efficiency achieve a dramatic improvement with the incorporation of the spinel component. More notably, the composite materials with increased spinel component exhibit superior rate capability compared with the parent Li‐rich material especially together with the highest capacity retention for x = 0.5 composition, making this as the optimal high‐energy high‐power material. The mechanisms involved in the symbiotic relationship of the spinel and layered Li‐rich components in the above composites are discussed.     

Toward a High‐Performance All‐Plastic Full Battery with a'Single Organic Polymer as Both Cathode and Anode

The design and fabrication of high‐performance all‐plastic batteries is essentially important to achieve future flexible electronics. A major challenge in this field is the lack of stable and reliable soft organic electrodes with satisfactory performance. Here, a novel all‐plastic‐electrode based Li‐ion battery with a single flexible bi‐functional ladderized heterocyclic poly(quinone), (C₆O₂S₂)_n, as both cathode and anode is demonstrated. Benefiting from its unique ladder‐like quinone and dithioether structure, the as‐prepared polymer cathode shows a high energy density of 624 Wh kg^?1 (vs lithium anode) and a stable battery life of 1000 cycles. Moreover, the as‐fabricated symmetric full‐battery delivers a large capacity of 249 mAh g^?1 (at 20 mA g^?1), a good capacity retention of 119 mAh g^?1 after 250 cycles (at 1.0 A g^?1) and a noteworthy energy density up to 276 Wh kg^?1. The superior performance of poly(2,3‐dithiino‐1,4‐benzoquinone)‐based electrode rivals most of the state‐of‐the‐art demonstrations on organic‐based metal‐ion shuttling batteries. The study provides an effective strategy to develop stable bi‐functional electrode materials toward the next‐generation of high performance all‐plastic batteries.     

New Class of Ni‐Rich Cathode Materials Li[NixCoyB1−x−y]O2 for Next Lithium Batteries

A new class of layered cathodes, Li[Ni_xCo_yB_1?x?y]O₂ (NCB), is synthesized. The proposed NCB cathodes have a unique microstructure in which elongated primary particles are tightly packed into spherical secondary particles. The cathodes also exhibit a strong crystallographic texture in which the a–b layer planes are aligned along the radial direction, facilitating Li migration. The microstructure, which effectively suppresses the formation of microcracks, improves the cycling stability of the NCB cathodes. The NCB cathode with 1.5 mol% B delivers a discharge capacity of 234 mAh g^?1 at 0.1 C and retains 91.2% of its initial capacity after 100 cycles (compared to values of 229 mAh g^?1 at 0.1 C and 78.8% for pristine Li[Ni_0.9Co_0.1]O₂). This study shows the importance of controlling the microstructure to obtain the required cycling stability, especially for Ni‐rich layered cathodes, where the main cause of capacity fading is related to mechanical strain in their charged state.     

A High‐Energy NASICON‐Type Cathode Material for Na‐Ion Batteries

Over the last decade, Na‐ion batteries have been extensively studied as low‐cost alternatives to Li‐ion batteries for large‐scale grid storage applications; however, the development of high‐energy positive electrodes remains a major challenge. Materials with a polyanionic framework, such as Na superionic conductor (NASICON)‐structured cathodes with formula Na_xM₂(PO₄)₃, have attracted considerable attention because of their stable 3D crystal structure and high operating potential. Herein, a novel NASICON‐type compound, Na₄MnCr(PO₄)₃, is reported as a promising cathode material for Na‐ion batteries that deliver a high specific capacity of 130 mAh g^?1 during discharge utilizing high‐voltage Mn^2+/3+ (3.5 V), Mn^3+/4+ (4.0 V), and Cr^3+/4+ (4.35 V) transition metal redox. In addition, Na₄MnCr(PO₄)₃ exhibits a high rate capability (97 mAh g^?1 at 5 C) and excellent all‐temperature performance. In situ X‐ray diffraction and synchrotron X‐ray diffraction analyses reveal reversible structural evolution for both charge and discharge.     

Mn‐Rich P′2‐Na0.67[Ni0.1Fe0.1Mn0.8]O2 as High‐Energy‐Density and Long‐Life Cathode Material for Sodium‐Ion Batteries

Herein, P′2‐type Na_0.67[Ni_0.1Fe_0.1Mn_0.8]O₂ is introduced as a promising new cathode material for sodium‐ion batteries (SIBs) that exhibits remarkable structural stability during repetitive Na⁺ de/intercalation. The O? Ni? O? Mn? O? Fe? O bond in the octahedra of transition‐metal layers is used to suppress the elongation of the Mn? O bond and to improve the electrochemical activity, leading to the highly reversible Na storage mechanism. A high discharge capacity of ≈220 mAh g^?1 (≈605 Wh kg^?1) is delivered at 0.05 C (13 mAg^?1) with a high reversible capacity of ≈140 mAh g^?1 at 3 C and excellent capacity retention of 80% over 200 cycles. This performance is associated with the reversible P′2–OP4 phase transition and small volume change upon charge and discharge (≈3%). The nature of the sodium storage mechanism in a full cell paired with a hard carbon anode reveals an unexpectedly high energy density of ≈542 Wh kg^?1 at 0.2 C and good capacity retention of ≈81% for 500 cycles at 1 C (260 mAg^?1).     

Open‐Structured V2O5·nH2O Nanoflakes as Highly Reversible Cathode Material for Monovalent and Multivalent Intercalation Batteries

The high‐capacity cathode material V₂O₅·n H₂O has attracted considerable attention for metal ion batteries due to the multielectron redox reaction during electrochemical processes. It has an expanded layer structure, which can host large ions or multivalent ions. However, structural instability and poor electronic and ionic conductivities greatly handicap its application. Here, in cell tests, self‐assembly V₂O₅·n H₂O nanoflakes shows excellent electrochemical performance with either monovalent or multivalent cation intercalation. They are directly grown on a 3D conductive stainless steel mesh substrate via a simple and green hydrothermal method. Well‐layered nanoflakes are obtained after heat treatment at 300 °C (V₂O₅·0.3H₂O). Nanoflakes with ultrathin flower petals deliver a stable capacity of 250 mA h g^?1 in a Li‐ion cell, 110 mA h g^?1 in a Na‐ion cell, and 80 mA h g^?1 in an Al‐ion cell in their respective potential ranges (2.0–4.0 V for Li and Na‐ion batteries and 0.1–2.5 V for Al‐ion battery) after 100 cycles.     

Optimization of Carbon‐ and Binder‐Free Au Nanoparticle‐Coated Ni Nanowire Electrodes for Lithium‐Oxygen Batteries

A Au nanoparticle‐coated Ni nanowire substrate without binder or carbon is used as the electrode (denoted as the Au/Ni electrode) for Li‐oxygen (Li‐O₂) batteries. A minimal amount of Au nanoparticles with sizes of <30 nm on a Ni nanowire substrate are coated using a simple electrodeposition method to the extent that maximum capacity can be utilized. This optimized, one body, Au/Ni electrode shows high capacities of 921 mAh g^?1_Au, 591 mAh g^?1_Au, and 359 mAh g^?1_Au, which are obtained at currents of 300 mAg^?1_Au, 500 mAg^?1_Au, and 1000 mAg^?1_Au respectively. More importantly, the Au/Ni electrode exhibits excellent cycle stability over 200 cycles.     

A Flexible Porous Carbon Nanofibers‐Selenium Cathode with Superior Electrochemical Performance for Both Li‐Se and Na‐Se Batteries

A flexible and free‐standing porous carbon nanofibers/selenium composite electrode (Se@PCNFs) is prepared by infiltrating Se into mesoporous carbon nanofibers (PCNFs). The porous carbon with optimized mesopores for accommodating Se can synergistically suppress the active material dissolution and provide mechanical stability needed for the film. The Se@PCNFs electrode exhibits exceptional electrochemical performance for both Li‐ion and Na‐ion storage. In the case of Li‐ion storage, it delivers a reversible capacity of 516 mAh g^?1 after 900 cycles without any capacity loss at 0.5 A g^?1. Se@PCNFs still delivers a reversible capacity of 306 mAh g^?1 at 4 A g^?1. While being used in Na‐Se batteries, the composite electrode maintains a reversible capacity of 520 mAh g^?1 after 80 cycles at 0.05 A g^?1 and a rate capability of 230 mAh g^?1 at 1 A g^?1. The high capacity, good cyclability, and rate capability are attributed to synergistic effects of the uniform distribution of Se in PCNFs and the 3D interconnected PCNFs framework, which could alleviate the shuttle reaction of polyselenides intermediates during cycling and maintain the perfect electrical conductivity throughout the electrode. By rational and delicate design, this type of self‐supported electrodes may hold great promise for the development of Li‐Se and Na‐Se batteries with high power and energy densities.     

3D Cube‐Maze‐Like Li‐Rich Layered Cathodes Assembled from 2D Porous Nanosheets for Enhanced Cycle Stability and Rate Capability of Lithium‐Ion Batteries

Li‐rich oxide is a promising candidate for the cathodes of next‐generation lithium‐ion batteries. However, its utilization is restricted by cycling instability and inferior rate capability. To tackle these issues, three‐dimensional (3D), hierarchical, cube‐maze‐like Li‐rich cathodes assembled from two‐dimensional (2D), thin nanosheets with exposed {010} active planes, are developed by a facile hydrothermal approach. Benefiting from their unique architecture, 3D cube‐maze‐like cathodes demonstrate a superior reversible capacity (285.3 mAh g^?1 at 0.1 C, 133.4 mAh g^?1 at 20.0 C) and a great cycle stability (capacity retention of 87.4% after 400 cycles at 2.0 C, 85.2% after 600 cycles and 75.0% after 1200 cycles at 20.0 C). When this material is matched with a graphite anode, the full cell achieves a remarkable discharge capacity (275.2 mAh g^?1 at 0.1 C) and stable cycling behavior (capacity retention of 88.7% after 100 cycles at 5.0 C, capacity retention of 84.8% after 100 cycles at 20.0 C). The present work proposes an accessible way to construct 3D hierarchical architecture assembled from 2D nanosheets with exposed high‐energy active {010} planes and verifies its validity for advanced Li‐rich cathodes.     

Porosity‐Controlled TiNb2O7 Microspheres with Partial Nitridation as A Practical Negative Electrode for High‐Power Lithium‐Ion Batteries

Titanium niobium oxide (TiNb₂O₇) has been recognized as a promising anode material for lithium‐ion batteries (LIBs) in view of its potential to operate at high rates with improved safety and high theoretical capacity of 387 mAh g^?1. However, it suffers from poor Li⁺ ion diffusivity and low electronic conductivity originated from its wide band gap energy (E_g > 2 eV). Here, porous TiNb₂O₇ microspheres (PTNO MSs) are prepared via a facile solvothermal reaction. PTNO MSs have a particle size of ≈1.2 μm and controllable pore sizes in the range of 5–35 nm. Ammonia gas nitridation treatment is conducted on PTNO MSs to introduce conducting Ti_1?xNb_xN layer on the surface and form nitridated PTNO (NPTNO) MSs. The porous structure and conducting Ti_1?xNb_xN layer enhance the transport kinetics associated with Li⁺ ions and electrons, which leads to significant improvement in electrochemical performance. As a result, the NPTNO electrode shows a high discharge capacity of ≈265 mAh g^?1, remarkable rate capability (≈143 mAh g^?1 at 100 C) and durable long‐term cyclability (≈91% capacity retention over 1000 cycles at 5 C). These results demonstrate the great potential of TiNb₂O₇ as a practical high‐rate anode material for LIBs.