Molecular Level Insight into Enhanced n‐Type Transport in Solution‐Printed Hybrid Thermoelectrics

Perylene diimide (PDI) derivatives hold great promise as stable, solution‐printable n‐type organic thermoelectric materials, but as of yet lack sufficient electrical conductivity to warrant further development. Hybrid PDI‐inorganic nanomaterials have the potential to leverage these physical advantages while simultaneously achieving higher thermoelectric performance. However, lack of molecular level insight precludes design of high performing PDI‐based hybrid thermoelectrics. Herein, the first explicit crystal structure of these materials is reported, providing previously inaccessible insight into the relationship between their structure and thermoelectric properties. Allowing this molecular level insight to drive novel methodologies, simple solution‐based techniques to prepare PDI hybrid thermoelectric inks with up to 20‐fold enhancement in thermoelectric power factor over the pristine molecule (up to 17.5 µW mK^?2) is presented. This improved transport is associated with reorganization of organic molecules on the surface of inorganic nanostructures. Additionally, outstanding mechanical flexibility is demonstrated by fabricating solution‐printed thermoelectric modules with innovative folded geometries. This work provides the first direct evidence that packing/organization of organic molecules on inorganic nanosurfaces is the key to effective thermoelectric transport in nanohybrid systems.     

High‐Performance GeTe‐Based Thermoelectrics: from Materials to Devices

High‐performance GeTe‐based thermoelectrics have been recently attracting growing research interest. Here, an overview is presented of the structural and electronic band characteristics of GeTe. Intrinsically, compared to low‐temperature rhombohedral GeTe, the high‐symmetry and high‐temperature cubic GeTe has a low energy offset between L and Σ points of the valence band, the reduced direct bandgap and phonon group velocity, and as a result, high thermoelectric performance. Moreover, their thermoelectric performance can be effectively enhanced through either carrier concentration optimization, band structure engineering (bandgap reduction, band degeneracy, and resonant state engineering), or restrained lattice thermal conductivity (phonon velocity reduction or phonon scattering). Consequently, the dimensionless figure of merit, ZT values, of GeTe‐based thermoelectric materials can be higher than 2. The mechanical and thermal stabilities of GeTe‐based thermoelectrics are highlighted, and it is found that they are suitable for practical thermoelectric applications except for their high cost. Finally, it is recognized that the performance of GeTe‐based materials can be further enhanced through synergistic effects. Additionally, proper material selection and module design can further boost the energy conversion efficiency of GeTe‐based thermoelectrics.     

Optimum Carrier Concentration in n‐Type PbTe Thermoelectrics

Taking La‐ and I‐doped PbTe as an example, the current work shows the effects of optimizing the thermoelectric figure of merit, zT, by controlling the doping level. The high doping effectiveness allows the carrier concentration to be precisely designed and prepared to control the Fermi level. In addition to the Fermi energy tuning, La‐doping modifies the conduction band, leading to an increase in the density of states effective mass that is confirmed by transport, infrared reflectance and hard X‐ray photoelectron spectroscopy measurements. Taking such a band structure modification effect into account, the electrical transport properties can then be well‐described by a self‐consistent single non‐parabolic Kane band model that yields an approximate (m*T)^1.5 dependence of the optimal carrier concentration for a peak power factor in both doping cases. Such a simple temperature dependence also provides an effective approximation of carrier concentration for a peak zT and helps to explain, the effects of other strategies such as lowering the lattice thermal conductivity by nanostructuring or alloying in n‐PbTe, which demonstrates a practical guide for fully optimizing thermoelectric materials in the entire temperature range. The principles used here should be equally applicable to other thermoelectric materials.     

Low‐Temperature‐Processed Colloidal Quantum Dots as Building Blocks for Thermoelectrics

Colloidal quantum dots (CQDs) are demonstrated to be promising materials to realize high‐performance thermoelectrics owing to their low thermal conductivity. The most studied CQD films, however, are using long ligands that require high processing and operation temperature (>400 °C) to achieve optimum thermoelectric performance. Here the thermoelectric properties of CQD films cross‐linked using short ligands that allow strong inter‐QD coupling are reported. Using the ligands, p‐type thermoelectric solids are demonstrated with a high Seebeck coefficient and power factor of 400 μV K^?1 and 30 µW m^?1 K^?2, respectively, leading to maximum ZT of 0.02 at a lower measurement temperature (<400 K) and lower processing temperature (<300 °C). These ligands further reduce the annealing temperature to 175 °C, significantly increasing the Seebeck coefficient of the CQD films to 580 μV K^?1. This high Seebeck coefficient with a superior ZT near room temperature compared to previously reported high temperature‐annealed CQD films is ascribed to the smaller grain size, which enables the retainment of quantum confinement and significantly increases the hole effective mass in the films. This study provides a pathway to approach quantum confinement for achieving a high Seebeck coefficient yet strong inter‐QD coupling, which offers a step toward low‐temperature‐processed high‐performance thermoelectric generators.     

Lead‐Free Thermoelectrics: High Figure of Merit in p‐type AgSnmSbTem+2

Thermoelectric materials based on Pb‐free compositions are of considerable current interest in environmentally friendly power‐generation applications derived from waste‐heat sources. Here, a new study of the thermoelectric properties of the tin‐based compositions with the general formula AgSn_mSbTe_m+2 (m = 2, 4, 5, 7, 10, 14, 18) is presented, where the m value is used as the tuning parameter of the thermoelectric properties. The electrical conductivity, Seebeck coefficient, and thermal conductivity are measured from 300 K to 723 K and the resulting thermoelectric figure of merit is determined as a function of the SnTe/AgSbTe₂ ratio. A thermoelectric figure of merit ZT ≈1 is obtained at 710 K for m = 4, indicating that the system AgSn_mSbTe_m+2 holds great promise as an alternative p‐type, lead‐free, thermoelectric material.     

Efficient Perovskite Photovoltaic‐Thermoelectric Hybrid Device

An efficient perovskite photovoltaic‐thermoelectric hybrid device is demonstrated by integrating the hole‐conductor‐free perovskite solar cell based on TiO₂/ZrO₂/carbon structure and the thermoelectric generator. The whole solar spectrum of AM 1.5 G is fully utilized with the ≈1.55 eV band gap perovskite (5‐AVA)_x(MA)_1?xPbI₃ absorbing the visible light and the carbon back contact absorbing the infrared light. The added thermoelectric generator improves the device performance by converting the thermal energy into electricity via the Seebeck effect. An optimized hybrid device is obtained with a maximum point power output of 20.3% and open‐circuit voltage of 1.29 V under the irradiation of 100 mW cm^?2.     

Going Beyond Lithium Hybrid Capacitors: Proposing a New High‐Performing Sodium Hybrid Capacitor System for Next‐Generation Hybrid Vehicles Made with Bio‐Inspired Activated Carbon

A novel sodium hybrid capacitor (NHC) is constructed with an intercalation‐type sodium material [carbon coated‐Na₃V₂(PO₄)₃, C‐NVP] and high surface area‐activated carbon derived from an eco‐friendly resource cinnamon sticks (CDCs) in an organic electrolyte. This novel NHC possesses a combination of high energy and high power density, along with remarkable electrochemical stability. In addition, the C‐NVP/CDC system outperforms present, well‐established lithium hybrid capacitor systems in all areas, and can thus be added to the list of candidates for future electric vehicles. A careful optimization of mass balance between electrode materials enables the C‐NVP/CDC cell to exhibit extraordinary capacitance performance. This novel NHC produces an energy density of 118 Wh kg^?1 at a specific power of 95 W kg^?1 and retains an energy density of 60 Wh kg^?1 with high specific power of 850 W kg^?1. Furthermore, a discharge capacitance of 53 F g^?1 is obtained from the C‐NVP/CDC cell at a 1 mA cm^?2 current density, along with 95% capacitance retention, even after 10 000 cycles. The sluggish kinetics of the Na ion battery system is successfully overcome by developing a stable, high‐performing NHC system.     

Hybrid Dye‐Titania Nanoparticles for Superior Low‐Temperature Dye‐Sensitized Solar Cells

In this work, a new strategy to design low‐temperature (≤200 °C) sintered dye‐sensitized solar cells (lt‐DSSC) is reported to enhance charge collection efficiencies (η_coll), photoconversion efficiencies (η), and stabilities under continuous operation conditions. Realization of lt‐DSSC is enabled by the integration of hybrid nanoparticles based on TiO₂‐Ru(II) complex (TiO₂_Ru_IS)—obtained by in situ bottom‐up construction of Ru(II) N3 dye‐sensitized titania—into the photoelectrode. Incentives for the use of TiO₂_Ru_IS are i) dye stability due to its integration into the TiO₂ anatase network and ii) enhanced charge collection yield due to its significant resistance toward electron recombination with electrolytes. It is demonstrated that devices with single‐layer photoelectrodes featuring blends of P25 and TiO₂_Ru_IS give rise to a 60% η_coll relative to a 46% η_coll for devices with P25‐based photoelectrodes. Responsible for this trend is a better charge transport and a reduced electron recombination. When using a multilayered photoelectrode architecture with a top layer based only on TiO₂_Ru_IS, devices with an even higher η_coll (74%) featuring a η of around 8.75% and stabilities of 600 h are achieved. This represents the highest values reported for lt‐DSSC to date.     

Hybrid and Aqueous Lithium‐Air Batteries

Lithium‐air (Li‐air) batteries have become attractive because of their extremely high theoretical energy density. However, conventional Li‐air cells operating with non‐aqueous electrolytes suffer from poor cycle life and low practical energy density due to the clogging of the porous air cathode by insoluble discharge products, contamination of the organic electrolyte and lithium metal anode by moist air, and decomposition of the electrolyte during cycling. These difficulties may be overcome by adopting a cell configuration that consists of a lithium‐metal anode protected from air by a Li⁺‐ion solid electrolyte and an air electrode in an aqueous catholyte. In this type of configuration, a Li⁺‐ion conducting “buffer” layer between the lithium‐metal anode and the solid electrolyte is often necessary due to the instability of many solid electrolytes in contact with lithium metal. Based on the type of buffer layer, two different battery configurations are possible: “hybrid” Li‐air batteries and “aqueous” Li‐air batteries. The hybrid and aqueous Li‐air batteries utilize the same battery chemistry and face similar challenges that limit the cell performance. Here, an overview of recent developments in hybrid and aqueous Li‐air batteries is provided and the factors that influence their performance and impede their practical applications, followed by future directions are discussed.     

High‐Capacity All‐Solid‐State Sodium Metal Battery with Hybrid Polymer Electrolytes

All‐solid‐state sodium metal batteries (SSMBs) are of great interest for their high theoretical capacity, nonflammability, and relatively low cost owing partially to the abundance of sodium recourses. However, it is challenging to fabricate SSMBs because compared with their counterparts, which contain lithium metal, sodium metal is mechanically softer and more reactive toward the electrolyte. Herein, the synthesis and electrochemical properties of newly designed sodium‐containing hybrid network solid polymer electrolytes (SPEs) and their application in SSMBs are reported. The hybrid network is synthesized by controlled crosslinking of octakis(3‐glycidyloxypropyldimethylsiloxy)octasilsesquioxane and amine‐terminated polyethylene glycol in existence with sodium perchlorate (NaClO₄). Plating and stripping experiments using symmetric cells show prolonged cycle life of the SPEs, >5150 and 3550 h at current density of 0.1 and 0.5 mA cm^?2, respectively. The results for the first time show that the SPE|sodium metal interface migrates into the SPE phase upon cycling. SSMBs fabricated with the hybrid SPE sandwiched between sodium metal anode and bilayered δ‐Na_xV₂O₅ cathode exhibit record‐high specific capacity for solid sodium‐ion batteries of 305 mAh g^?1 and excellent Coulombic efficiency. This work demonstrates that the hybrid network SPEs are promising for SSMB applications.     

Hybrid Piezo/Triboelectric‐Driven Self‐Charging Electrochromic Supercapacitor Power Package

The rapid development of personal electronics imposes a great challenge on sustainable and maintenance‐free power supplies. The integration of nanogenerators (NG) and electrochromic supercapacitors (SC) offers a promising solution to efficiently convert mechanical energy to stored electrical energy in a predictable and noticeable manner. In this paper, by integrating hybrid NGs and electrochromic micro‐SCs (µ‐SCs) array, the authors demonstrate a smart self‐charging power package capable of indicating the charging state with color change. The electrochromic µ‐SC employs Ag nanowires/NiO as electrode materials, exhibiting high capacitance (3.47 mF cm^?2) and stable cycling performance (80.7% for 10000 cycles). The hybrid NG can produce a high output voltage of 150 V and an enhanced output current of 20 µA to satisfy the self‐charging requirements. The integrated electrochromic µ‐SCs array is capable of self‐charging to 3 V to light up a LED under human palm impact. The charging states can be estimated according to the color differences with the naked eye during the self‐charging process. Moreover, it is possible to design the planar interdigitated electrodes into different shapes according to user demand. The proposed simple and cost‐effective approaches for smart self‐charging power package may pave the way for future intelligent, independent and continuous operation of daily electronics.     

Rational Construction of Nitrogen‐Doped Hierarchical Dual‐Carbon for Advanced Potassium‐Ion Hybrid Capacitors

Potassium‐ion hybrid capacitors (PIHCs), elaborately integrate the advantages of high output power as well as long lifespan of supercapacitors and the high energy density of batteries, and exhibit great possibilities for the future generations of energy storage devices. The critical next step for future implementation lies in exploring a high‐rate battery‐type anode with an ultra‐stable structure to match the capacitor‐type cathode. Herein, a “dual‐carbon” is constructed, in which a three‐dimensional nitrogen‐doped microporous carbon polyhedron (NMCP) derived from metal‐organic frameworks is tightly wrapped by two‐dimensional reduced graphene oxide (NMCP@rGO). Benefiting from the synergistic effect of the inner NMCP and outer rGO, the NMCP@rGO exhibits a superior K‐ion storage capability with a high reversible capacity of 386 mAh g^?1 at 0.05 A g^?1 and ultra‐long cycle stability with a capacity of 151.4 mAh g^?1 after 6000 cycles at 5.0 A g^?1. As expected, the as‐assembled PIHCs with a working voltage as high as 4.2 V present a high energy/power density (63.6 Wh kg^?1 at 19 091 W kg^?1) and excellent capacity retention of 84.7% after 12 000 cycles. This rational construction of advanced PIHCs with excellent performance opens a new avenue for further application and development.     

Phosphorene as Cathode Material for High‐Voltage,Anti‐Self‐Discharge Zinc Ion Hybrid Capacitors

Output voltage and self‐discharge rate are two important performance indices for supercapacitors, which have long been overlooked, though these play a very significant role in their practical application. Here, a zinc anode is used to construct a zinc ion hybrid capacitor. Expanded operating voltage of the hybrid capacitor is obtained with novel electrolytes. In addition, significantly improved anti‐self‐discharge ability is achieved. The phosphorene‐based zinc ion capacitor exploiting a “water in salt” electrolyte with a working potential can reach 2.2 V, delivering 214.3 F g^?1 after 5000 cycles. The operating voltage is further extended to 2.5 V through the use of an organic solvent as the electrolyte; the solvent is prepared by adding 0.2 m ZnCl₂ into the tetraethylammonium tetrafluoroborate in propylene carbonate (Et₄NBF₄/PC) solvent, and it exhibits 105.9 F g^?1 even after 9500 cycles. More importantly, the phosphorene‐based capacitors possess excellent anti‐self‐discharge performance. The capacitors retain 76.16% of capacitance after resting for 300 h. The practical application of the zinc ion capacitor is demonstrated through a flexible paper‐based printed microcapacitor. It is believed that the developed zinc ion capacitor can effectively resolve the severe self‐discharge problem of supercapacitors. Moreover, high‐voltage zinc ion capacitors provide more opportunities for the application of supercapacitors.