Surface Engineering of TiO2 ETL for Highly Efficient and Hysteresis‐Less Planar Perovskite Solar Cell (21.4%) with Enhanced Open‐Circuit Voltage and Stability

Interfacial studies and band alignment engineering on the electron transport layer (ETL) play a key role for fabrication of high‐performance perovskite solar cells (PSCs). Here, an amorphous layer of SnO₂ (a‐SnO₂) between the TiO₂ ETL and the perovskite absorber is inserted and the charge transport properties of the device are studied. The double‐layer structure of TiO₂ compact layer (c‐TiO₂) and a‐SnO₂ ETL leads to modification of interface energetics, resulting in improved charge collection and decreased carrier recombination in PSCs. The optimized device based on a‐SnO₂/c‐TiO₂ ETL shows a maximum power conversion efficiency (PCE) of 21.4% as compared to 19.33% for c‐TiO₂ based device. Moreover, the modified device demonstrates a maximum open‐circuit voltage (V_oc) of 1.223 V with 387 mV loss in potential, which is among the highest reported value for PSCs with negligible hysteresis. The stability results show that the device on c‐TiO₂/a‐SnO₂ retains about 91% of its initial PCE value after 500 h light illumination, which is higher than pure c‐TiO₂ (67%) based devices. Interestingly, using a‐SnO₂/c‐TiO₂ ETL the PCE loss was only 10% of initial value under continuous UV light illumination after 30 h, which is higher than that of c‐TiO₂ based device (28% PCE loss).     

Improved SnO2 Electron Transport Layers Solution‐Deposited at Near Room Temperature for Rigid or Flexible Perovskite Solar Cells with High Efficiencies

Electron transport layer (ETL) is a functional layer of great significance for boosting the power conversion efficiency (PCE) of perovskite solar cells (PSCs). To date, it is still a challenge to simultaneously reduce the surface defects and improve the crystallinity in ETLs during their low‐temperature processing. Here, a novel strategy for the mediation of in situ regrowth of SnO₂ nanocrystal ETLs is reported: introduction of controlled trace amounts of surface absorbed water on the fluorinated tin oxide (FTO) or indium–tin oxide (ITO) surfaces of the substrates using ultraviolet ozone (UVO) pretreatment. The optimum amount of adsorbed water plays a key role in balancing the hydrolysis–condensation reactions during the structural evolution of SnO₂ thin films. This new approach results in a full‐coverage SnO₂ ETL with a desirable morphology and crystallinity for superior optical and electrical properties, as compared to the control SnO₂ ETL without the UVO pretreatment. Finally, the rigid and flexible PSC devices based on the new SnO₂ ETLs yield high PCEs of up to 20.5% and 17.5%, respectively.     

SrTiO3/Al2O3‐Graphene Electron Transport Layer for Highly Stable and Efficient Composites‐Based Perovskite Solar Cells with 20.6% Efficiency

For practical use of perovskite solar cells (PSCs) the instability issues of devices, attributed to degradation of perovskite molecules by moisture, ions migration, and thermal‐ and light‐instability, have to be solved. Herein, highly efficient and stable PSCs based on perovskite/Ag‐reduced graphene oxide (Ag‐rGO) and mesoporous Al₂O₃/graphene (mp‐AG) composites are reported. The mp‐AG composite is conductive with one‐order of magnitude higher mobility than mp‐TiO₂ and used for electron transport layer (ETL). Compared to the mp‐TiO₂ ETL based cells, the champion device based on perovskite/Ag‐rGO and SrTiO₃/mp‐AG composites shows overall a best performance (i.e., V_OC = 1.057 V, J_SC = 25.75 mA cm^?2, fill factor (FF) = 75.63%, and power conversion efficiency (PCE) = 20.58%). More importantly, the champion device without encapsulation exhibits not only remarkable thermal‐ and photostability but also long‐term stability, retaining 97–99% of the initial values of photovoltaic parameters and sustaining ≈93% of initial PCE over 300 d under ambient conditions.     

Simultaneous Improved Performance and Thermal Stability of Planar Metal Ion Incorporated CsPbI2Br All‐Inorganic Perovskite Solar Cells Based on MgZnO Nanocrystalline Electron Transporting Layer

The high thermal stability and facile synthesis of CsPbI₂Br all‐inorganic perovskite solar cells (AI‐PSCs) have attracted tremendous attention. As far as electron‐transporting layers (ETLs) are concerned, low temperature processing and reduced interfacial recombination centers through tunable energy levels determine the feasibility of the perovskite devices. Although the TiO₂ is the most popular ETL used in PSCs, its processing temperature and moderate electron mobility hamper the performance and feasibility. Herein, the highly stable, low‐temperature processed MgZnO nanocrystal‐based ETLs for dynamic hot‐air processed Mn²⁺ incorporated CsPbI2Br AI‐PSCs are reported. By holding its regular planar “n–i–p” type device architecture, the MgZnO ETL and poly(3‐hexylthiophene‐2,5‐diyl) hole transporting layer, 15.52% power conversion efficiency (PCE) is demonstrated. The thermal‐stability analysis reveals that the conventional ZnO ETL‐based AI‐PSCs show a serious instability and poor efficiency than the Mg²⁺ modified MgZnO ETLs. The photovoltaic and stability analysis of this improved photovoltaic performance is attributed to the suitable wide‐bandgap, low ETL/perovskite interface recombination, and interface stability by Mg²⁺ doping. Interestingly, the thermal stability analysis of the unencapsulated AI‐PSCs maintains >95% of initial PCE more than 400 h at 85 °C for MgZnO ETL, revealing the suitability against thermal degradation than conventional ZnO ETL.     

Efficient and Highly Air Stable Planar Inverted Perovskite Solar Cells with Reduced Graphene Oxide Doped PCBM Electron Transporting Layer

Reduced graphene oxide (rGO) is added in the [6,6]‐Phenyl‐C61‐butyric acid methyl ester (PCBM) electron transport layer (ETL) of planar inverted perovskite solar cells (PSCs), resulting in a power conversion efficiency (PCE) improvement of ≈12%, with a hysteresis‐free PCE of 14.5%, compared to 12.9% for the pristine PCBM based device. The universality of the method is demonstrated in PSCs based on CH₃NH₃PbI_3?x Cl_x and CH₃NH₃PbI₃ perovskites, deposited through one step and two step spin coating process, respectively. After a comprehensive spectroscopic characterization of both devices, it is clear that the introduction of rGO in PCBM ETL results in an important increase of the ETL conductivity, together with reduced series resistance and surface roughness. As a result, a significant photoluminescence quenching of such perovskite/ETL is observed, confirming the increased measured short circuit current density. Transient absorption measurements reveal that in the rGO‐based device, the relaxation process of the excited electrons is significantly faster compared to the reference, which implies that the charge injection rate is significantly faster for the first. Furthermore, the light soaking effect is significantly reduced. Finally, aging measurements reveal that the rGO stabilizes the ELT/perovskite interface, which results in the stabilization of perovskite crystal structure after prolonged illumination.     

Morphology Controlling of All‐Inorganic Perovskite at Low Temperature for Efficient Rigid and Flexible Solar Cells

All‐inorganic cesium lead halide (CsPbX₃) perovskites have emerged as promising photovoltaic materials owing to their superior thermal stability compared to traditional organic–inorganic hybrid counterparts. However, the CsPbX₃ perovskites generally need to be prepared at high‐temperature, which restricts their application in multilayer or flexible solar cells. Herein, the formation of CsPbX₃ perovskites at room‐temperature (RT) induced by dimethylsulphoxide (DMSO) coordination is reported. It is further found that a RT solvent (DMSO) annealing (RTSA) treatment is valid to control the perovskite crystallization dynamics, leading to uniform and void‐free films, and consequently a maximum power conversion efficiency (PCE) of 6.4% in the device indium tin oxide (ITO)/NiO _x /RT‐CsPbI₂Br/C₆₀/Bathocuproine (BCP)/Ag, which is, as far as it is known, the first report of RT solution‐processed CsPbX₃‐based perovskite solar cells (PSCs). Moreover, the efficiency can be boosted up to 10.4% by postannealing the RTSA‐treated perovskite film at an optimal temperature of 120 °C. Profiting from the moderate temperature, flexible PSCs are also demonstrated with a maximum PCE of 7.3% for the first time. These results may stimulate further development of all‐inorganic CsPbX₃ perovskites and their application in flexible electronics.     

Impermeable Charge Transport Layers Enable Aqueous Processing on Top of Perovskite Solar Cells

Several applications of perovskite solar cells (PSCs) demand a semitransparent top electrode to afford top‐illumination or see‐through devices. Transparent conductive oxides, such as indium tin oxide (ITO), typically require postdeposition annealing at elevated temperatures, which would thermally decompose the perovskite. In contrast, silver nanowires (AgNWs) in dispersions of water would be a very attractive alternative that can be deposited at ambient conditions. Water is environmentally friendly without safety concerns associated with alcohols, such as flammability. Due to the notorious moisture sensitivity of lead‐halide perovskites, aqueous processing of functional layers, such as electrodes, on top of a perovskite device stack is elusive. Here, impermeable electron transport layers (ETLs) are shown to enable the deposition of semitransparent AgNW electrodes from green aqueous dispersions on top of the perovskite cell without damage. The polyvinylpyrrolidone (PVP) capping agent of the AgNWs is found to cause a work–function shift and an energy barrier between the AgNWs and the adjacent ETL. Thus, a high carrier density (≈10¹⁸ cm^?3) in the ETL is required to achieve well‐behaved J/V characteristics free of s‐shapes. Ultimately, semitransparent PSCs are demonstrated that provide an efficiency of 17.4%, which is the highest efficiency of semitransparent p‐i‐n perovskite solar cells with an AgNW top electrode.     

Halogen Engineering for Operationally Stable Perovskite Solar Cells via Sequential Deposition

The performance of perovskite solar cells (PSCs) relies on the synthesis method and chemical composition of the perovskite materials. So far, PSCs that have adopted two‐step sequential deposited perovskite with the state‐of‐art composition (FAPbI₃)_1?x(MAPbBr₃)_x (x < 0.05) have achieved record power conversion efficiency (PCE), while their one‐step antisolvent dripping counterparts with typical composition Cs_0.05FA_0.81MA_0.14Pb(I_0.85Br_0.15)₃ with more bromine have exhibited much better long‐term operational stability. Thus, halogen engineering that aims to elevate bromine content in sequential deposited perovskite film would push operational stability of PSCs toward that of antisolvent dripping deposited perovskite materials. Here, a Br‐rich seeding growth method is devised and perovskite seed solution with high bromine content is introduced into a PbI₂ precursor, leading to bromine incorporation in the resulting perovskite film. Photovoltaic devices fabricated by Br‐rich seeding growth method exhibit a PCE of 21.5%, similar to 21.6% for PSCs having lower bromine content. Whereas, the operational stability of PSCs with higher bromine content is significantly enhanced, with over 80% of initial PCE retained after 500 h tracking at maximum power point under 1‐sun illumination. This work highlights the vital importance of halogen composition for the operational stability of PSCs, and introduces an effective way to incorporate bromine into mixed‐cation‐halide perovskite film via sequential deposition method.     

Fusing Nanowires into Thin Films: Fabrication of Graded‐Heterojunction Perovskite Solar Cells with Enhanced Performance

Perovskite solar cells (PSCs) have recently experienced a rapid rise in power conversion efficiency (PCE), but the prevailing PSCs with conventional mesoscopic or planar device architectures still contain nonideal perovskite/hole‐transporting‐layer (HTL) interfaces, limiting further enhancement in PCE and device stability. In this work, CsPbBr₃ perovskite nanowires are employed for modifying the surface electronic states of bulk perovskite thin films, forming compositionally‐graded heterojunction at the perovskite/HTL interface of PSCs. The nanowire morphology is found to be key to achieving lateral homogeneity in the perovskite film surface states resulting in a near‐ideal graded heterojunction. The hidden role of such lateral homogeneity on the performance of graded‐heterojunction PSCs is revealed for the first time. The resulting PSCs show high PCE up to 21.4%, as well as high operational stability, which is superior to control PSCs fabricated without CsPbBr₃‐nanocrystals modification and with CsPbBr₃‐nanocubes modification. This study demonstrates the promise of controlled hybridization of perovskite nanowires and bulk thin films for more efficient and stable PSCs.     

Simultaneous Contact and Grain‐Boundary Passivation in Planar Perovskite Solar Cells Using SnO2‐KCl Composite Electron Transport Layer

The performance of perovskite solar cells is sensitive to detrimental defects, which are prone to accumulate at the interfaces and grain boundaries of bulk perovskite films. Defect passivation at each region will lead to reduced trap density and thus less nonradiative recombination loss. However, it is challenging to passivate defects at both the grain boundaries and the bottom charge transport layer/perovskite interface, mainly due to the solvent incompatibility and complexity in perovskite formation. Here SnO₂‐KCl composite electron transport layer (ETL) is utilized in planar perovskite solar cells to simultaneously passivate the defects at the ETL/perovskite interface and the grain boundaries of perovskite film. The K and Cl ions at the ETL/perovskite interface passivate the ETL/perovskite contact. Meanwhile, K ions from the ETL can diffuse through the perovskite film and passivate the grain boundaries. An enhancement of open‐circuit voltage from 1.077 to 1.137 V and a corresponding power conversion efficiency increasing from 20.2% to 22.2% are achieved for the devices using SnO₂‐KCl composite ETL. The composite ETL strategy reported herein provides an avenue for defect passivation to further increase the efficiency of perovskite solar cells.     

Solvent‐Mediated Dimension Tuning of Semiconducting Oxide Nanostructures as Efficient Charge Extraction Thin Films for Perovskite Solar Cells with Efficiency Exceeding 16%

The recent surge in efficiency and progress of organohalide perovskite solar cells (PSCs) has been significant. The PSC performance is significantly influenced by nanostructuring as this varies the intrinsic optical, electrical, and electrochemical properties. Diverse TiO₂ electron transport layers (ETLs) are solvothermally grown on the transparent conducting oxide substrate with different dimensionalities, 0D nanoparticles (TNP), 1D nanowires (TNW) to 2D nanosheets (TNS), by varying the organic solvent used. These layers feature enhanced optical transparency (≈2%–5% transmittance improvement compared to pristine fluorine doped tin oxide, FTO, glass) minimizing light absorption losses. PSCs constructed using 1D TNW or 2D TNS yield enhanced photovoltaic performance compared to the 0D TNP counterparts. This is a result of i) improved infiltration of the perovskite in the porous TNW or TNS network and ii) facilitated electron transport and charge extraction at the TNW/perovskite or TNS/perovskite interfaces, thus reduced interfacial recombination loss. Employing a bilayered ETL film consisting of a self‐assembled TiO₂ blocking layer and a subsequent TNW active layer, produces PSC devices with an efficiency exceeding 16%. This bilayered ETL film can simultaneously block the photogenerated holes and enhance electron ­extraction, therefore improving PSC performance.     

Orientation Regulation of Phenylethylammonium Cation Based 2D Perovskite Solar Cell with Efficiency Higher Than 11%

Increasing the power conversion efficiency (PCE) of the two‐dimensional (2D) perovskite‐based solar cells (PVSCs) is really a challenge. Vertical orientation of the 2D perovskite film is an efficient strategy to elevate the PCE. In this work, vertically orientated highly crystalline 2D (PEA)₂(MA)_n–1Pb_nI_3n+1 (PEA= phenylethylammonium, MA = methylammonium, n = 3, 4, 5) films are fabricated with the assistance of an ammonium thiocyanate (NH₄SCN) additive by a one‐step spin‐coating method. Planar‐structured PVSCs with the device structure of indium tin oxide (ITO)/poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate)/(PEA)₂(MA)_n–1Pb_nI_3n+1/[6,6]‐phenyl‐C61‐butyric acid methyl ester/bahocuproine/Ag are fabricated. The PCE of the PVSCs is boosted from the original 0.56% (without NH₄SCN) to 11.01% with the optimized NH₄SCN addition at n = 5, which is among the highest PCE values for the low‐n (n < 10) 2D perovskite‐based PVSCs. The improved performance is attributed to the vertically orientated highly crystalline 2D perovskite thin films as well as the balanced electron/hole transportation. The humidity stability of this oriented 2D perovskite thin film is also confirmed by the almost unchanged X‐ray diffraction patterns after 28 d exposed to the moisture in a humidity‐controlled cabinet (H_r = 55 ± 5%). The unsealed device retains 78.5% of its original PCE after 160 h storage in air atmosphere with humidity of 55 ± 5%. The results provide an effective approach toward a highly efficient and stable PVSC for future commercialization.     

Synergistic Crystal and Interface Engineering for Efficient and Stable Perovskite Photovoltaics

The presence of bulk and surface defects in perovskite light harvesting materials limits the overall efficiency of perovskite solar cells (PSCs). The formation of such defects is suppressed by adding methylammonium chloride (MACl) as a crystallization aid to the precursor solution to realize high‐quality, large‐grain triple A‐cation perovskite films and that are combined with judicious engineering of the perovskite interface with the electron and hole selective contact materials. A planar SnO₂/TiO₂ double layer oxide is introduced to ascertain fast electron extraction and the surface of the perovskite facing the hole conductor is treated with iodine dissolved in isopropanol to passivate surface trap states resulting in a retardation of radiationless carrier recombination. A maximum solar to electric power conversion efficiency (PCE) of 21.65% and open circuit photovoltage (V_oc) of ≈1.24 V with only ≈370 mV loss in potential with respect to the band gap are achieved, by applying these modifications. Additionally, the defect healing enhances the operational stability of the devices that retain 96%, 90%, and 85% of their initial PCE values after 500 h under continuously light illumination at 20, 50, and 65 °C, respectively, demonstrating one of the most stable planar PSCs reported so far.     

Efficient and Hysteresis‐Free Perovskite Solar Cells Based on a Solution Processable Polar Fullerene Electron Transport Layer

Fullerene derivatives, which possess extraordinary geometric shapes and high electron affinity, have attracted significant attention for thin film technologies. This study demonstrates an important photovoltaic application using carboxyl‐functionalized carbon buckyballs, C60 pyrrolidine tris‐acid (CPTA), to fabricate electron transport layers (ETLs) that replace traditional metal oxide‐based ETLs in efficient and stable n‐i‐p‐structured planar perovskite solar cells (PSCs). The uniform CPTA film is covalently anchored onto the surface of indium tin oxide (ITO), significantly suppressing hysteresis and enhancing the flexural strength in the CPTA‐modified PSCs. Moreover, solution‐processable CPTA‐based ETLs also enable the fabrication of lightweight flexible PSCs. The maximum‐performing device structures composed of ITO/CPTA/CH₃NH₃PbI₃/2,2′,7,7′‐tetrakis‐(N,N‐di‐p‐methoxyphenylamine)‐9,9′‐spirobifluorene (spiro‐OMeTAD)/Au yield power conversion efficiencies of more than 18% on glass substrates and up to 17% on flexible substrates. These results indicate that the CPTA layers provide new opportunities for solution‐processed organic ETLs by substantially simplifying the procedure for fabricating PSCs for portable applications.     

Highly stable and Efficient Perovskite Solar Cells Based on FAMA‐Perovskite‐Cu:NiO Composites with 20.7% Efficiency and 80.5% Fill Factor

To solve critical issues related to device stability and performance of perovskite solar cells (PSCs), FA_0.026MA_0.974PbI_3?yCl_y‐Cu:NiO (formamidinium methylammonium (FAMA)‐perovskite‐Cu:NiO) and Al₂O₃/Cu:NiO composites are developed and utilized for fabrication of highly stable and efficient PSCs through fully‐ambient‐air processes. The FAMA‐perovskite‐Cu:NiO composite crystals prepared without using any antisolvents not only improve the perovskite film quality with large‐size crystals and less grain boundaries but also tailor optical and electronic properties and suppress charge recombination with reduction of trap density. A champion device based on the composites as light absorber and Al₂O₃/Cu:NiO interfacial layer between electron transport layer and active layer yields power conversion efficiency (PCE) of 20.67% with V_OC of 1.047 V, J_SC of 24.51 mA cm^?2, and fill factor of 80.54%. More importantly, such composite‐based PSCs without encapsulation show significant enhancement in long‐term air‐stability, thermal‐ and photostability with retaining 97% of PCE over 240 d under ambient conditions (25–30 °C, 45–55% humidity).     

Solvent Engineering Boosts the Efficiency of Paintable Carbon‐Based Perovskite Solar Cells to Beyond 14%

Carbon‐based hole transport material (HTM)‐free perovskite solar cells (PSCs) have shown much promise for practical applications because of their high stability and low cost. However, the efficiencies of this kind of PSCs are still relatively low, especially for the simplest paintable carbon‐based PSCs, in comparison with the organic HTM‐based PSCs. This can be imputed to the perovskite deposition methods that are not very suitable for this kind of devices. A solvent engineering strategy based on two‐step sequential method is exploited to prepare a high‐quality perovskite layer for the paintable carbon‐based PSCs in which the solvent for CH₃NH₃I (MAI) solution at the second step is changed from isopropanol (IPA) to a mixed solvent of IPA/Cyclohexane (CYHEX). This mixed solvent not only accelerates the conversion of PbI₂ to CH₃NH₃PbI₃ but also suppresses the Ostwald ripening process resulting in a high‐quality perovskite layer, e.g., pure phase, even surface, and compact capping layer. The paintable carbon‐based PSCs fabricated from IPA/CYHEX solvent exhibits a considerable enhancement in photovoltaic performance and performance reproducibility in comparison with that from pure IPA, especially on fill factor (FF), owing mainly to the better contact of perovskite/carbon interface, lower trap density in perovskite, higher light absorption ability, and faster charge transport of perovskite layer. As a result, the highest power conversion efficiency (PCE) of 14.38% is obtained, which is a record value for carbon‐based HTM‐free PSCs. Furthermore, a PCE of as high as 10% is achieved for the large area device (1 cm²), also the highest of its kind.     

Synergic Interface and Optical Engineering for High‐Performance Semitransparent Polymer Solar Cells

In this study the thickness of the PTB7‐Th:PC₇₁BM bulk heterojunction (BHJ) film and the PF3N‐2TNDI electron transport layer (ETL) is systematically tuned to achieve polymer solar cells (PSCs) with optimized power conversion efficiency (PCE) of over 9% when an ultrathin BHJ of 50 nm is used. Optical modeling suggests that the high PCE is attributed to the optical spacer effect from the ETL, which not only maximizes the optical field within the BHJ film but also facilitates the formation of a more homogeneously distributed charge generation profile across the BHJ film. Experimentally it is further proved that the extra photocurrent produced at the PTB7‐Th/PF3N‐2TNDI interface also contributes to the improved performance. Taking advantage of this high performance thin film device structure, one step further is taken to fabricate semitransparent PSCs (ST‐PSCs) by using an ultrathin transparent Ag cathode to replace the thick Ag mirror cathode, yielding a series of high performance ST‐PSCs with PCEs over 6% and average visible transmittance between 20% and 30%. These ST‐PSCs also possess remarkable transparency color perception and rendering properties, which are state‐of‐the‐art and fulfill the performance criteria for potential use as power‐generating windows in near future.     

Improving Interfacial Charge Recombination in Planar Heterojunction Perovskite Photovoltaics with Small Molecule as Electron Transport Layer

Although perovskite solar cells (PSCs) have emerged as a promising alternative to widely used fossil fuels, the involved high‐temperature preparation of metal oxides as a charge transport layer in most state‐of‐the‐art PSCs has been becoming a big stumbling block for future low‐temperature and large‐scale R2R manufacturing process. Such an issue strongly encourages scientists to find new type of materials to replace metal oxides. Except for expensive PC₆₁BM with unmanageable morphology and electrical properties, the past investigation on the development of low‐temperature‐processed and highly efficient electron transport layers (ETLs) has met some mixed success. In order to further enhance the performance of all‐solution‐processed PSCs, we propose a novel n‐type sulfur‐containing small molecule hexaazatrinaphtho[2,3‐c][1,2,5]thiadiazole (HATNT) with high electron mobility up to 1.73 × 10^?2 cm² V^?1 s^?1 as an ETL in planar heterojunction PSCs. A high power conversion efficiency of 18.1% is achieved, which is fully comparable with the efficiency from the control device fabricated with PC₆₁BM as ETL. This superior performance mainly attributes from more effective suppression of charge recombination at the perovskite/HATNT interface than that between the perovskite and PC₆₁ BM. Moreover, high electron mobility and strong interfacial interaction via S? I or S? Pb bonding should be also positive factors. Significantly, our results undoubtedly enable new guidelines in exploring n‐type organic small molecules for high‐performance PSCs.     

Hot‐Substrate Deposition of Hole‐ and Electron‐Transport Layers for Enhanced Performance in Perovskite Solar Cells

Charge transport layers play an important role in determining the power conversion efficiencies (PCEs) of perovskite solar cells (PSCs). However, it has proven challenging to produce thin and compact charge transport layers via solution processing techniques. Herein, a hot substrate deposition method capable of improving the morphology of high‐coverage hole‐transport layers (HTLs) and electron‐transport layers (ETLs) is reported. PSC devices using HTLs deposited on a hot substrate show improvement in the open‐circuit voltage (V_oc) from 1.041 to 1.070 V and the PCE from 17.00% to 18.01%. The overall device performance is then further enhanced with the hot substrate deposition of ETLs as the V_oc and PCE reach 1.105 V and 19.16%, respectively. The improved performance can be explained by the decreased current leakage and series resistance, which are present in PSCs with rough and discontinuous HTLs and ETLs.     

The Synergism of DMSO and Diethyl Ether for Highly Reproducible and Efficient MA0.5FA0.5PbI3 Perovskite Solar Cells

Composition and film quality of perovskite are crucial for the further improvement of perovskite solar cells (PSCs), including efficiency, reproducibility, and stability. Here, it is demonstrated that by simply mixing 50% of formamidinium (FA⁺) into methylammonium lead iodide (MAPbI₃), a highly crystalline, stable phase, and compact, polycrystalline grain morphology perovskite is formed by using a solvent‐mediated phase transformation process via the synergism of dimethyl sulfoxide and diethyl ether, which shows long carrier lifetime, low trap state density, and a record certified 21.8% power conversion efficiency (PCE) in pure‐iodide, alkaline‐metal‐free MA_0.5FA_0.5PbI₃ perovskite‐based PSCs. These PSCs show very high operational stability, with 85% PCE retention upon 1000 h 1 Sun intensity illumination. A 17.33% PCE module (6.5 × 7 cm²) is also demonstrated, attesting to the scalability of such devices.