Extended Light Harvesting with Dual Cu2O‐Based Photocathodes for High Efficiency Water Splitting

Cu₂O is one of the most promising light absorbing materials for solar energy conversion. Previous studies with Cu₂O for water splitting usually deliver high photocurrent or high photovoltage, but not both. Here, a Cu₂O/Ga₂O₃/TiO₂/RuO_x photocathode that benefits from a high quality thermally oxidized Cu₂O layer and good band alignment of the Ga₂O₃ buffer layer is reported, yielding a photocurrent of 6 mA cm^?2 at 0 V versus reversible hydrogen electrode (RHE), an onset potential of 0.9 V versus RHE, and 3.5 mA cm^?2 at 0.5 V versus RHE. The quantum efficiency spectrum (incident photon to current efficiency, IPCE) reveals a dramatically improved green/red response and a decreased blue response compared with electrodeposited Cu₂O films. Light intensity dependence and photocurrent transient studies enable the identification of the limitations in the performance. Due to the complementary IPCE curves of thermally oxidized and electrodeposited Cu₂O photocathodes, a dual photocathode is fabricated to maximize the absorption over the entire range of above band gap radiation. Photocurrents of 7 mA cm^?2 at 0 V versus RHE are obtained in the dual photocathodes, with an onset potential of 0.9 V versus RHE and a thermodynamically based energy conversion efficiency of 1.9%.     

Carbon Nitride/Reduced Graphene Oxide Film with Enhanced Electron Diffusion Length: An Efficient Photo‐Electrochemical Cell for Hydrogen Generation

Polymeric carbon nitride (CN) has emerged as a promising semiconductor for energy‐related applications. However, its utilization in photo‐electrochemical cells is still very limited owing to poor electron–hole separation efficiency, short electron diffusion length, and low absorption coefficient. Here the synthesis of a highly porous carbon nitride/reduced graphene oxide (CN‐rGO) film with good photo‐electrochemical properties is reported. The CN‐rGO film exhibits long electron diffusion length and high electrochemical active surface area, good charge separation, and enhanced light‐harvesting properties. The film displays a 20‐fold enhancement of photocurrent density over pristine CN, reaching up to 75 µA cm^?2 at 1.23 V versus reversible hydrogen electrode (RHE) in an alkaline solution, as well as stability over a wide pH range. Photocurrent measurements with a hole scavenger reveal a photocurrent density of 660 µA cm^?2 at 1.23 V versus RHE and a quantum efficiency of 60% at 400 nm, resulting in the production of 0.8 mol h^?1 g^?1 of hydrogen. The substantial photo‐electrochemical activity enhancement and hydrogen production together with the low price, high electrochemical surface area, long electron diffusion length, stability under harsh condition, and tunable photophysical properties of CN materials open many possibilities for their utilization in (photo)electrochemical and electronic devices.     

Boosting the Performance of WO3/n‐Si Heterostructures for Photoelectrochemical Water Splitting: from the Role of Si to Interface Engineering

Metal oxide/Si heterostructures make up an exciting design route to high‐performance electrodes for photoelectrochemical (PEC) water splitting. By monochromatic light sources, contributions of the individual layers in WO₃/n‐Si heterostructures are untangled. It shows that band bending near the WO₃/n‐Si interface is instrumental in charge separation and transport, and in generating a photovoltage that drives the PEC process. A thin metal layer inserted at the WO₃/n‐Si interface helps in establishing the relation among the band bending depth, the photovoltage, and the PEC activity. This discovery breaks with the dominant Z‐scheme design idea, which focuses on increasing the conductivity of an interface layer to facilitate charge transport, but ignores the potential profile around the interface. Based on the analysis, a high‐work‐function metal is predicted to provide the best interface layer in WO₃/n‐Si heterojunctions. Indeed, the fabricated WO₃/Pt/n‐Si photoelectrodes exhibit a 2 times higher photocurrent density at 1.23 V versus reversible hydrogen electrode (RHE) and a 10 times enhancement at 1.6 V versus RHE compared to WO₃/n‐Si. Here, it is essential that the native SiO₂ layer at the interface between Si and the metal is kept in order to prevent Fermi level pinning in the Schottky contact between the Si and the metal.     

Overcoming Charge Collection Limitation at Solid/Liquid Interface by a Controllable Crystal Deficient Overlayer

Bulk and surface charge recombination of photoelectrode are two key processes that significantly hinder solar‐to‐fuel conversion of photoelectrochemical cell (PEC). In this study, the function of a “crystal‐deficient” overlayer is unveiled, which outperforms a traditionally used amorphous or crystalline overlayer in PEC water splitting by exhibiting a high conductivity and large electron diffusion length to enable unlimited electron collection. The optimized ≈2.5 nm thickness of the “crystal‐deficient” shell results in a depletion layer with a width of 3 nm, which overcomes the flat band limitation of the photovoltage and increases the light absorptivity in the wavelength range from 300 to 420 nm. In addition, a 50‐fold increase in the conductivity yields a one‐order‐of‐magnitude increase in the diffusion length of an electron (L_n )(≈20 μm), allowing for unlimited electron collection in the 1.9 μm TiO₂ nanowire array with the “crystal‐deficient” shell. The controllable “crystal‐deficient” overlayer in rutile TiO₂ nanowires photoanode achieves a photocurrent density greater than 2.0 mA cm^?2 at 1.23 V versus reversible hydrogen electrode (RHE), a 1.18% applied bias photon‐to‐current efficiency at 0.49 V versus RHE, a faradaic efficiency greater than 93.5% at 0.6 V versus Pt under air mass 1.5G simulated solar light illumination (100 mW cm^?2).     

3D Porous Pyramid Heterostructure Array Realizing Efficient Photo‐Electrochemical Performance

Direct photo‐electrochemical (PEC) water splitting is of great practical interest for developing a sustainable energy systems, but remains a big challenge owing to sluggish charge separation, low efficiency, and poor stability. Herein, a 3D porous In₂O₃/In₂S₃ pyramid heterostructure array on a fluorine‐doped tin oxide substrate is fabricated by an ion exchange–induced synthesis strategy. Based on the synergistic structural and electronic modulations from density functional theory calculations and experimental observations, 3D porous In₂O₃/In₂S₃ photoanode by the protective layer delivers a low onset potential of ≈0.02 V versus reversible hydrogen electrode (RHE), the highest photocurrent density of 8.2 mA cm^?2 at 1.23 V versus RHE among all the In₂S₃ photoanodes reported to date, an incident photon‐to‐current efficiency of 76% at 400 nm, and high stability over 20 h for PEC water splitting are reported. This work provides an alternative promising prototype for the design and construction of novel heterostructures in robust PEC water splitting applications.     

(040)‐Crystal Facet Engineering of BiVO4 Plate Photoanodes for Solar Fuel Production

A (040)‐crystal facet engineered BiVO₄ ((040)‐BVO) photoanode is investigated for solar fuel production. The (040)‐BVO photoanode is favorable for improved charge carrier mobility and high photocatalytic active sites for solar light energy conversion. This crystal facet design of the (040)‐BVO photoanode leads to an increase in the energy conversion efficiency for solar fuel production and an enhancement of the oxygen evolution rate. The photocurrent density of the (040)‐BVO photoanode is determined to be 0.94 mA cm^?2 under AM 1.5 G illumination and produces 42.1% of the absorbed photon‐to‐current conversion efficiency at 1.23 V (vs RHE, reversible hydrogen electrode). The enhanced charge separation efficiency and improved charge injection efficiency driven by (040) facet can produce hydrogen with 0.02 mmol h^?1 at 1.23 V. The correlation between the (040)‐BVO photoanode and the solar fuel production is investigated. The results provide a promising approach for the development of solar fuel production using a BiVO₄ photoanode.     

A Sandwich‐Like Organolead Halide Perovskite Photocathode for Efficient and Durable Photoelectrochemical Hydrogen Evolution in Water

Organolead halide perovskite materials have demonstrated great potential in the solar cells field owing to their excellent optoelectronic properties. However, the instability issue of the perovskites impedes the translation of their attractive features for the solar fuel production such as photoelectrochemical H₂ production from water splitting. Herein, CH₃NH₃PbI₃ a photocathode with a sandwich‐like structure is fabricated with a general and scalable approach toward addressing this issue. The photocathode exhibits an onset potential at 0.95 V versus reversible hydrogen electrode (RHE) and a photocurrent density of ?18 mA cm^?2 at 0 V versus RHE with an impressive ideal ratiometric power‐saved efficiency of 7.63%. More impressively, the photocathode retains good stability under 12 h continuous illumination in water at wide pH range. This performance is much superior to that of the best perovskite‐based photoelectrode ever reported.     

Efficient and Stable TiO2:Pt–Cu(In,Ga)Se2 Composite Photoelectrodes for Visible Light Driven Hydrogen Evolution

Novel thin film composite photocathodes based on device‐grade Cu(In,Ga)Se₂ chalcopyrite thin film absorbers and transparent conductive oxide Pt‐implemented TiO₂ layers on top are presented for an efficient and stable solar‐driven hydrogen evolution. Thin films of phase‐pure anatase TiO₂ are implemented with varying Pt‐concentrations in order to optimize simultaneously i) conductivity of the films, ii) electrocatalytic activity, and iii) light‐guidance toward the chalcopyrite. Thereby, high incident‐photon‐to‐current‐efficiencies of more than 80% can be achieved over the full visible light range. In acidic electrolyte (pH 0.3), the most efficient Pt‐implemented TiO₂–Cu(In,Ga)Se₂ composite electrodes reveal i) photocurrent densities up to 38 mA cm^?2 in the saturation region (?0.4 V RHE, reversible hydrogen electrode), ii) 15 mA cm^?2 at the thermodynamic potential for H₂‐evolution (0 V RHE), and iii) an anodic onset potential shift for the hydrogen evolution (+0.23 V RHE). It is shown that the gradual increase of the Pt‐concentration within the TiO₂ layers passes through an efficiency‐ and stability‐maximum of the device (5 vol% of Pt precursor solution). At this maximum, optimized light‐incoupling into the device‐grade chalcopyrite light‐absorber as well as electron conductance properties within the surface layer are achieved while no degradation are observed over more than 24 h of operation.     

MOF‐Based Transparent Passivation Layer Modified ZnO Nanorod Arrays for Enhanced Photo‐Electrochemical Water Splitting

This study introduces zeolitic imidazolate framework‐8 (ZIF‐8) as the first metal‐organic framework based transparent surface passivation layer for photo‐electrochemical (PEC) water splitting. A significant enhancement for PEC water oxidation is demonstrated based on the in situ seamless coating of ZIF‐8 surface passivation layer on Ni foam (NF) supported ZnO nanorod arrays photoanode. The PEC performance is improved by optimizing the ZIF‐8 thickness and by grafting Ni(OH)₂ nanosheets as synergetic co‐catalyst. With respect to ZnO/NF, the optimized Ni(OH)₂/ZIF‐8/ZnO/NF photoanode exhibits a two times larger photocurrent density of 1.95 mA cm^?2 and also a two times larger incident photon to current conversion efficiency of 40.05% (350 nm) at 1.23 V versus RHE (V_RHE) under AM 1.5 G. The synergetic surface passivation and the co‐catalyst modification contribute to prolonging the charge lifetime, to promoting the charge transfer, and to decreasing the overpotential for water oxidation.     

A Bottom‐Up Approach toward All‐Solution‐Processed High‐Efficiency Cu(In,Ga)S2 Photocathodes for Solar Water Splitting

The development of solution‐processable routes to prepare efficient photoelectrodes for water splitting is highly desirable to reduce manufacturing costs. Recently, sulfide chalcopyrites (Cu(In,Ga)S₂) have attracted attention as photocathodes for hydrogen evolution owing to their outstanding optoelectronic properties and their band gap—wider than their selenide counterparts—which can potentially increase the attainable photovoltage. A straightforward and all‐solution‐processable approach for the fabrication of highly efficient photocathodes based on Cu(In,Ga)S₂ is reported for the first time. It is demonstrated that semiconductor nanocrystals can be successfully employed as building blocks to prepare phase‐pure microcrystalline thin films by incorporating different additives (Sb, Bi, Mg) that promote the coalescence of the nanocrystals during annealing. Importantly, the grain size is directly correlated to improved charge transport for Sb and Bi additives, but it is shown that secondary effects can be detrimental to performance even with large grains (for Mg). For optimized electrodes, the sequential deposition of thin layers of n‐type CdS and TiO₂ by solution‐based methods, and platinum as an electrocatalyst, leads to stable photocurrents saturating at 8.0 mA cm^–2 and onsetting at ≈0.6 V versus RHE under AM 1.5G illumination for CuInS₂ films. Electrodes prepared by our method rival the state‐of‐the‐art performance for these materials.     

Drastic Layer‐Number‐Dependent Activity Enhancement in Photocatalytic H2 Evolution over nMoS2/CdS (n ≥ 1) Under Visible Light

Exploiting noble‐metal‐free cocatalysts is of huge interest for photocatalytic water splitting using solar energy. As an efficient cocatalyst in photocatalysis, MoS₂ is shown promise as a low‐cost alternative to Pt for hydrogen evolution. Here we report a systematical study on controlled synthesis of MoS₂ with layer number ranging from ≈1 to 112 and their activities for photocatalytic H₂ evolution over commercial CdS. A drastic increase in photocatalytic H₂ evolution is observed with decreasing MoS₂ layer number. Particularly for the single‐layer (SL) MoS₂, the SL‐MoS₂/CdS sample reaches a high H₂ generation rate of ≈2.01 × 10^?3m h^?1 in Na₂S–Na₂SO₃ solutions and ≈2.59 × 10^?3m h^?1 in lactic acid solutions, corresponding to an apparent quantum efficiency of 30.2% and 38.4% at 420 nm, respectively. In addition to the more exposed edges and unsaturated active S atoms, valence band–XPS and Mott–Schottky plots analysis indicate that the SL MoS₂ has the more negative conduction band energy level than the H⁺/H₂ potential, facilitating the hydrogen reduction.     

A Delaminated Defect‐Rich ZrO2 Hierarchical Nanowire Photocathode for Efficient Photoelectrochemical Hydrogen Evolution

An efficient way to combat the energy crisis and the greenhouse gas effect of fossil fuels is the production of hydrogen fuel from solar‐driven water splitting reaction. Here, this study presents a p‐type ZrO₂ nanoplate‐decorated ZrO₂ nanowire photocathode with a high photoconversion efficiency that makes it potentially viable for commercial solar H₂ production. The composition of oxygen vacancy defects, low charge carrier transport property, and high specific surface area of these as‐grown hierarchical nanowires are further improved by an hydrofluoric acid (HF) treatment, which causes partial delamination and produces a thin amorphous ZrO₂ layer on the surface of the as‐grown nanostructured film. The presence of different types of oxygen vacancies (neutral, singly charged, and doubly charged defects) and their compositional correlation to the Zr^x+ oxidation states (4 > x > 2) are found to affect the charge transfer process, the p‐type conductivity, and the photocatalytic activity of the ZrO₂ nanostructured film. The resulting photocathode provides the highest overall photocurrent (?42.3 mA cm^?2 at 0 V vs reversible hydrogen electrode (RHE)) among all the photocathodes reported to date, and an outstanding 3.1% half‐cell solar‐to‐hydrogen conversion efficiency with a Faradaic efficiency of 97.8%. Even more remarkable is that the majority of the photocurrent (69%) is produced in the visible light region.     

Synthesis of Large Surface‐Area g‐C3N4 Comodified with MnOx and Au‐TiO2 as Efficient Visible‐Light Photocatalysts for Fuel Production

Herein, this study successfully fabricates porous g‐C₃N₄‐based nanocomposites by decorating sheet‐like nanostructured MnO_x and subsequently coupling Au‐modified nanocrystalline TiO₂. It is clearly demonstrated that the as‐prepared amount‐optimized nanocomposite exhibits exceptional visible‐light photocatalytic activities for CO₂ conversion to CH₄ and for H₂ evolution, respectively by ≈28‐time (140 µmol g^?1 h^?1) and ≈31‐time (313 µmol g^?1 h^?1) enhancement compared to the widely accepted outstanding g‐C₃N₄ prepared with urea as the raw material, along with the calculated quantum efficiencies of ≈4.92% and 2.78% at 420 nm wavelength. It is confirmed mainly based on the steady‐state surface photovoltage spectra, transient‐state surface photovoltage responses, fluorescence spectra related to the produced ?OH amount, and electrochemical reduction curves that the exceptional photoactivities are comprehensively attributed to the large surface area (85.5 m² g^?1) due to the porous structure, to the greatly enhanced charge separation and to the introduced catalytic functions to the carrier‐related redox reactions by decorating MnO_x and coupling Au‐TiO₂, respectively, to modulate holes and electrons. Moreover, it is suggested mainly based on the photocatalytic experiments of CO₂ reduction with isotope ¹³CO₂ and D₂O that the produced ?CO₂ and ?H as active radicals would be dominant to initiate the conversion of CO₂ to CH₄.     

Highly Efficient Sunlight‐Driven Seawater Splitting in a Photoelectrochemical Cell with Chlorine Evolved at Nanostructured WO3 Photoanode and Hydrogen Stored as Hydride within Metallic Cathode

A seawater splitting photoelectrochemical cell featuring a nanostructured tungsten trioxide photoanode that exhibits very high and stable photocurrents producing chlorine with average 70% Faradaic efficiency is described. Fabrication of the WO₃ electrodes on fluorine‐doped tin oxide substrates involves a simple solution‐based method and sequential layer‐by‐layer deposition with a progressively adjusted amount of structure‐directing agent in the precursor and a two‐step annealing. Such a procedure allows tailoring of thick, highly porous, structurally stable WO₃ films with a large internal photoactive surface area optimizing utilization of visible light wavelengths by the photoanode. With the application of an anodic potential of 0.76 V versus Ag/AgCl reference electrode (0.4 V below the thermodynamic Cl₂/Cl^? potential) in synthetic seawater, the designed WO₃ photoanodes irradiated with simulated 1 sun AM 1.5G light reach currents exceeding 4.5 mA cm^?2. Photocurrents close to 5 mA cm^?2 are attained in the case of fresh water splitting using 1 m methane–sulfonic acid supporting electrolyte with oxygen evolved at the WO₃ photoanode. The amount of formed hydrogen is determined by discharging the palladium sheet electrode employed as a cathode. Collection of hydrogen in the form of a hydride opens, more generally, the prospect of subsequently using such materials as anodes in batteries employing oxygen reduction cathodes.     

Leaf‐Mosaic‐Inspired Vine‐Like Graphitic Carbon Nitride Showing High Light Absorption and Efficient Photocatalytic Hydrogen Evolution

Green plants use solar energy efficiently in nature. Simulating the exquisite structure of a natural photosynthesis system may open a new approach for the construction of desirable photocatalysts with high light harvesting efficiency and performance. Herein, inspired by the excellent light utilization of “leaf mosaic” in plants, a novel vine‐like g‐C₃N₄ (V‐CN) is synthesized for the first time by copolymerizing urea with dicyandiamide‐formaldehyde (DF) resin. The as‐prepared V‐CN exhibits ultrahigh photocatalytic hydrogen production of 13.6 mmol g^?1 h^?1 under visible light and an apparent quantum yield of 12.7% at 420 nm, which is ≈38 times higher than that of traditional g‐C₃N₄, representing one of the highest‐activity g‐C₃N₄‐based photocatalysts. This super photocatalytic performance is derived from the unique leaf mosaic structure of V‐CN, which effectively improves its light utilization and affords a larger specific surface area. In addition, the introduction of DF resin further optimizes the energy band of V‐CN, extends its light absorption, and improves its crystallinity and interfacial charge transport, resulting in high performance. It is an easy and green strategy for the preparation of broad‐spectrum, high‐performance g‐C₃N₄, which presents significant advancement for the design of other nanophotocatalysts by simulating the fine structure of natural photosynthesis.     

Retarded Charge–Carrier Recombination in Photoelectrochemical Cells from Plasmon‐Induced Resonance Energy Transfer

N‐type metal oxides such as hematite (α‐Fe₂O₃) and bismuth vanadate (BiVO₄) are promising candidate materials for efficient photoelectrochemical water splitting; however, their short minority carrier diffusion length and restricted carrier lifetime result in undesired rapid charge recombination. Herein, a 2D arranged globular Au nanosphere (NS) monolayer array with a highly ordered hexagonal hole pattern (hereafter, Au array) is introduced onto the surface of photoanodes comprised of metal oxide films via a facile drying and transfer‐printing process. Through plasmon‐induced resonance energy transfer, the Au array provides a strong electromagnetic field in the near‐surface area of the metal oxide film. The near‐field coupling interaction and amplification of the electromagnetic field suppress the charge recombination with long‐lived photogenerated holes and simultaneously enhance the light harvesting and charge transfer efficiencies. Consequently, an over 3.3‐fold higher photocurrent density at 1.23 V versus reversible hydrogen electrode (RHE) is achieved for the Au array/α‐Fe₂O₃. Furthermore, the high versatility of this transfer printing of Au arrays is demonstrated by introducing it on the molybdenum‐doped BiVO₄ film, resulting in 1.5‐fold higher photocurrent density at 1.23 V versus RHE. The tailored metal film design can provide a potential strategy for the versatile application in various light‐mediated energy conversion and optoelectronic devices.     

Scalable Triple Cation Mixed Halide Perovskite–BiVO4 Tandems for Bias‐Free Water Splitting

Strong interest exists in the development of organic–inorganic lead halide perovskite photovoltaics and of photoelectrochemical (PEC) tandem absorber systems for solar fuel production. However, their scalability and durability have long been limiting factors. In this work, it is revealed how both fields can be seamlessly merged together, to obtain scalable, bias‐free solar water splitting tandem devices. For this purpose, state‐of‐the‐art cesium formamidinium methylammonium (CsFAMA) triple cation mixed halide perovskite photovoltaic cells with a nickel oxide (NiO_x) hole transport layer are employed to produce Field's metal‐epoxy encapsulated photocathodes. Their stability (up to 7 h), photocurrent density (–12.1 ± 0.3 mA cm^?2 at 0 V versus reversible hydrogen electrode, RHE), and reproducibility enable a matching combination with robust BiVO₄ photoanodes, resulting in 0.25 cm² PEC tandems with an excellent stability of up to 20 h and a bias‐free solar‐to‐hydrogen efficiency of 0.35 ± 0.14%. The high reliability of the fabrication procedures allows scaling of the devices up to 10 cm², with a slight decrease in bias‐free photocurrent density from 0.39 ± 0.15 to 0.23 ± 0.10 mA cm^?2 due to an increasing series resistance. To characterize these devices, a versatile 3D‐printed PEC cell is also developed.     

Direct Growth of Flower‐Like δ‐MnO2 on Three‐Dimensional Graphene for High‐Performance Rechargeable Li‐O2 Batteries

A challenge still remains to develop high‐performance and cost‐effective air electrode for Li‐O₂ batteries with high capacity, enhanced rate capability and long cycle life (100 times or above) despite recent advances in this field. In this work, a new design of binder‐free air electrode composed of three‐dimensional (3D) graphene (G) and flower‐like δ‐MnO₂ (3D‐G‐MnO₂) has been proposed. In this design, graphene and δ‐MnO₂ grow directly on the skeleton of Ni foam that inherits the interconnected 3D scaffold of Ni foam. Li‐O₂ batteries with 3D‐G‐MnO₂ electrode can yield a high discharge capacity of 3660 mAh g^?1 at 0.083 mA cm^?2. The battery can sustain 132 cycles at a capacity of 492 mAh g^?1 (1000 mAh g_carbon ^?1) with low overpotentials under a high current density of 0.333 mA cm^?2. A high average energy density of 1350 Wh Kg^?1 is maintained over 110 cycles at this high current density. The excellent catalytic activity of 3D‐G‐MnO₂ makes it an attractive air electrode for high‐performance Li‐O₂ batteries.     

Molybdenum Disulfide/Nitrogen‐Doped Reduced Graphene Oxide Nanocomposite with Enlarged Interlayer Spacing for Electrocatalytic Hydrogen Evolution

Facile design of low‐cost and highly active catalysts from earth‐abundant elements is favorable for the industrial application of water splitting. Here, a simple strategy to synthesize an ultrathin molybdenum disulfide/nitrogen‐doped reduced graphene oxide (MoS₂/N‐RGO‐180) nanocomposite with the enlarged interlayer spacing of 9.5 Å by a one‐step hydrothermal method is reported. The synergistic effects between the layered MoS₂ nanosheets and N‐doped RGO films contribute to the high activity for hydrogen evolution reaction (HER). MoS₂/N‐RGO‐180 exhibits the excellent catalytic activity with a low onset potential of ?5 mV versus reversible hydrogen elelctrode (RHE), a small Tafel slope of 41.3 mV dec^?1, a high exchange current density of 7.4 × 10^?4 A cm^?2, and good stability over 5 000 cycles under acidic conditions. The HER performance of MoS₂/N‐RGO‐180 nanocomposite is superior to the most reported MoS₂‐based catalysts, especially its onset potential and exchange current density. In this work, a novel and simple method to the preparation of low‐cost MoS₂‐based electrocatalysts with the extraordinary HER performance is presented.     

Exceptional Visible‐Light‐Driven Cocatalyst‐Free Photocatalytic Activity of g‐C3N4 by Well Designed Nanocomposites with Plasmonic Au and SnO2

In this work, plasmonic Au/SnO₂/g‐C₃N₄ (Au/SO/CN) nanocomposites have been successfully synthesized and applied in the H₂ evolution as photocatalysts, which exhibit superior photocatalytic activities and favorable stability without any cocatalyst under visible‐light irradiation. The amount‐optimized 2Au/6SO/CN nanocomposite capable of producing approximately 770 μmol g^?1 h^?1 H₂ gas under λ > 400 nm light illumination far surpasses the H₂ gas output of SO/CN (130 μmol g^?1), Au/CN (112 μmol g^?1 h^?1), and CN (11 μmol g^?1 h^?1) as a contrast. In addition, the photocatalytic activity of 2Au/6SO/CN maintains unchanged for 5 runs in 5 h. The enhanced photoactivity for H₂ evolution is attributed to the prominently promoted photogenerated charge separation via the excited electron transfer from plasmonic Au (≈520 nm) and CN (470 nm > λ > 400 nm) to SO, as indicated by the surface photovoltage spectra, photoelectrochemical I–V curves, electrochemical impedance spectra, examination of formed hydroxyl radicals, and photocurrent action spectra. Moreover, the Kelvin probe test indicates that the newly aligned conduction band of SO in the fabricated 2Au/6SO/CN is indispensable to assist developing a proper energy platform for the photocatalytic H₂ evolution. This work distinctly provides a feasible strategy to synthesize highly efficient plasmonic‐assisted CN‐based photocatalysts utilized for solar fuel production.