All‐Solid‐State On‐Chip Supercapacitors Based on Free‐Standing 4H‐SiC Nanowire Arrays

All‐solid‐state on‐chip SiC supercapacitors (SCs) based on free‐standing SiC nanowire arrays (NWAs) are reported. In comparison to the widely used technique based on the interdigitated fingers, the present strategy can be much more facile for constructing on‐chip SCs devices, which is directly sandwiched with a solid electrolyte layer between two pieces of SiC NWAs film without any substrate. The mass loading of active materials of on‐chip SiC SCs can be up to ≈5.6 mg cm^?2, and the total device thickness is limited in ≈40 µm. The specific area energy and power densities of the SCs device reach 5.24 µWh cm^?2 and 11.2 mW cm^?2, and their specific volume energy and power densities run up to 1.31 mWh cm^–3 and 2.8 W cm^?3, respectively, which are two orders of magnitude higher than those of state‐of‐the‐art SiC‐based SCs, and also much higher than those of other solid‐state carbon‐based SCs ever reported. Furthermore, such on‐chip SCs exhibit superior rate capability and robust stability with over 94% capacitance retention after 10 000 cycles at a scan rate of 100 mV s^?1, representing their high performance in all merits.     

On‐Chip MXene Microsupercapacitors for AC‐Line Filtering Applications

Microsupercapacitors (MSCs) with high energy densities offer viable miniaturized alternatives to bulky electrolytic capacitors if the former can respond at the kilo Hertz (kHz) or higher frequencies. Moreover, MSCs fabricated on a chip can be integrated into thin‐film electronics in a compatible manner, serving the function of ripple filtering units or harvesters of energy from high‐frequency sources. In this work, wafer‐scale fabrication is demonstrated of MXene microsupercapacitors with controlled flake sizes and engineered device designs to achieve excellent frequency filtering performance. Specifically, the devices (100 nm thick electrodes and 10 µm interspace) deliver high volumetric capacitance (30 F cm^?3 at 120 Hz), high rate capability (300 V s^?1), and a very short relaxation time constant (τ₀ = 0.45 ms), surpassing conventional electrolytic capacitors (τ₀ = 0.8 ms). As a result, the devices are capable of filtering 120 Hz ripples produced by AC line power at a frequency of 60 Hz. This study opens new avenues for exploring miniaturized MXene MSCs as replacements for bulky electrolytic capacitors.     

Bio‐Nanotechnology in High‐Performance Supercapacitors

The use of bio‐nanotechnology for the fabrication of diverse functional nanomaterials with precisely controlled morphologies and microstructures is attracting considerable attention due to its sustainability and renewability. As one of the key energy storage devices, supercapacitor (SC) requires the active electrode material to have high specific surface area, interconnected porous structure, excellent electronic conductivity, and appropriate heteroatom doping for promoting the transfer of electrons and electrolyte ions. The combination of bio‐technology and SC will open up a new avenue for the large‐scale fabrication of high performance functional energy storage devices. In this review, the most state‐of‐the‐art research progress in bio‐nanotechnological fabrication of different nanomaterials, including carbon materials, metal oxides, conducting polymers, and their corresponding composites are reviewed with the following three bio‐nanotechnical approaches covered: (1) biomass carbonization technologies; (2) bio‐template methods; and (3) bio‐complex technologies, while also highlighting their applications as functional SC electrodes.     

Graphitic Petal Electrodes for All‐Solid‐State Flexible Supercapacitors

The charge storage characteristics of a composite nanoarchitecture with a highly functional 3D morphology are reported. The electrodes are formed by the electropolymerization of aniline monomers into a nanometer‐thick polyaniline (PANI) film that conformally coats graphitic petals (GPs) grown by microwave plasma chemical vapor deposition (MPCVD) on conductive carbon cloth (CC). The hybrid CC/GPs/PANI electrodes yield results near the theoretical maximum capacitance for PANI of 2000 F g^?1 (based on PANI mass) and a large area‐normalized specific capacitance of ≈2.6 F cm^?2 (equivalent to a volumetric capacitance of ≈230 F cm^?3) at a low current density of 1 A g^?1 (based on PANI mass). The specific capacitances remain above 1200 F g^?1 (based on PANI mass) for currents up to 100 A g^?1 with correspondingly high area‐normalized values. The hybrid electrodes also exhibit a high rate capability with an energy density of 110 Wh kg^?1 and a maximum power density of 265 kW kg^?1 at a current density of 100 A g^?1. Long‐term cyclic stability is good (≈7% loss of initial capacitance after 2000 cycles), with coulombic efficiencies >99%. Moreover, prototype all‐solid‐state flexible supercapacitors fabricated from these hybrid electrodes exhibit excellent energy storage performance.     

On‐target ultrasonic digestion of proteins

In the present work, we report a novel on‐target protein cleavage method. The method utilizes ultrasonic energy and allows up to 20 samples to be cleaved in 5 min for protein identification and one sample in 30 s for on‐tissue digestion. The standard proteins were spotted on a conductive glass slide in a volume of 0.5 μL followed by 5 min of ultrasonication after trypsin addition. Controls (5 min, 37°C no ultrasonication) were also assayed. After trypsin addition, digestion of the tissues was enhanced by 30 s of ultrasonication. The samples were analyzed and compared to those obtained by using conventional 3 h heating proteolysis. The low sample volume needed for the digestion and reduction in sample‐handling steps and time are the features that make this method appealing to the many laboratories working with high‐throughput sample treatment.     

Facile and Scalable Preparation of Ruthenium Oxide‐Based Flexible Micro‐Supercapacitors

Tremendous efforts have been invested in the development of the internet of things during the past 10 years. Implantable sensors still need embedded miniaturized energy harvesting devices, since commercialized thin films and microbatteries do not provide sufficient power densities and suffer from limited lifetime. Therefore, micro‐supercapacitors are good candidates to store energy and deliver power pulses while providing non‐constant voltage output with time. However, multistep expensive protocols involving mask aligners and sophisticated cleanrooms are used to prepare these devices. Here, a simple and versatile laser‐writing procedure to integrate flexible micro‐supercapacitors and microbatteries on current‐collector‐free polyimide foils is reported, starting from commercial powders. Ruthenium oxide (RuO₂)‐based micro‐supercapacitors are prepared by laser irradiation of a bilayered tetrachloroauric acid (HAuCl₄ · 3H₂O)–cellulose acetate/RuO₂ film deposited by spin‐coating, which leads to adherent Au/RuO₂ electrodes with a unique pillar morphology. The as‐prepared microdevices deliver 27 mF cm^?2/540 F cm^?3 in 1 m H₂SO₄ and retain 80% of the initial capacitance after 10 000 cycles. This simple process is applied to make carbon‐based micro‐supercapacitors, as well as metal oxide based pseudocapacitors and battery electrodes, thus offering a straightforward solution to prepare low‐cost flexible microdevices at a large scale.     

An Efficient Ultra‐Flexible Photo‐Charging System Integrating Organic Photovoltaics and Supercapacitors

Flexible and biocompatible integrated photo‐charging devices consisting of photovoltaic cells and energy storage units can provide an independent power supply for next‐generation wearable electronics or biomedical devices. However, current flexible integrated devices exhibit low total energy conversion and storage efficiency and large device thickness, hindering their applicability towards efficient and stable self‐powered systems. Here, a highly efficient and ultra‐thin photo‐charging device with a total efficiency approaching 6% and a thickness below 50 µm is reported, prepared by integrating 3‐µm‐thick organic photovoltaics on 40 µm‐thick carbon nanotube/polymer‐based supercapacitors. This flexible photo‐charging capacitor delivers much higher performance compared with previous reports by tuning the electrochemical properties of the composite electrodes, which reduce the device thickness to 1/8 while improving the total efficiency by 15%. The devices also exhibit a superior operational stability (over 96% efficiency retention after 100 charge/discharge cycles for one week) and mechanical robustness (94.66% efficiency retention after 5000 times bending at a radius of around 2 mm), providing a high‐power and long‐term operational energy source for flexible and wearable electronics.     

On‐ground habitat restoration: Interview with Nancy Pallin

Nancy Pallin has been involved in bush regeneration practice for over 25 years as well as being involved in conservation advocacy. Her main work, helping to establish the Ku‐ring‐gai Flying‐Fox Reserve and coordinating its ecological restoration, draws on an ability to interpret nature to others and inspire collective action     

On‐demand killing of adherent cells on photo‐acid‐generating culture substrates

As a powerful tool of cell screening and cell purification, we developed a novel method to kill adherent cells as cultured on a substrate by micro‐projection of incoherent visible light. To kill the cells by the mild light irradiated by electrically controllable micro‐projection systems currently available, we introduced the assist of the photo‐responsive culture substrates functionalized with a photo‐acid‐generating polymer. In clear contrast to the existing laser‐based methods requiring point scanning, areal micro‐prjection of blue light with the wavelength 436 nm killed many CHO‐K1 cells at a time in the irradiated area on the substrate. The effect of the photo‐generated acid was so confined that selective killing of targeted cells was achieved without critical damage to the neighboring cells. Further, we demonstrated the photo‐selective killing of the adherent cells after preliminarily patterning through the photo‐induced removal of cell adhesion‐inhibiting polymer. Biotechnol. Bioeng. 2013; 110: 348–352. © 2012 Wiley Periodicals, Inc.     

On‐plate‐selective enrichment of glycopeptides using boronic acid‐modified gold nanoparticles for direct MALDI‐QIT‐TOF MS analysis

In this study, an on‐plate‐selective enrichment method is developed for fast and efficient glycopeptide investigation. Gold nanoparticles were first spotted and sintered on a stainless‐steel plate, then modified with 4‐mercaptophenylboronic acid to provide porous substrate with large specific surface and dual functions. These spots were used to selectively capture glycopeptides from peptide mixtures and the captured target peptides could be analyzed by MALDI‐MS simply by deposition of 2,5‐dihydroxybenzoic acid matrix. Horseradish peroxidase was employed as a standard glycoprotein to investigate the enrichment efficiency. In this way, the enrichment, washing and detection steps can all be fulfilled on a single MALDI target plate. The relatively small sample amount needed, low detection limit and rapid selective enrichment have made this on‐plate strategy promising for online enrichment of glycopeptides, which could be applied in high‐throughput proteome research.     

Scalable,Self‐Aligned Printing of Flexible Graphene Micro‐Supercapacitors

Graphene micro‐supercapacitors (MSCs) are an attractive energy storage technology for powering miniaturized portable electronics. Despite considerable advances in recent years, device fabrication typically requires conventional microfabrication techniques, limiting the translation to cost‐effective and high‐throughput production. To address this issue, we report here a self‐aligned printing process utilizing capillary action of liquid inks in microfluidic channels to realize scalable, high‐fidelity manufacturing of graphene MSCs. Microstructured ink receivers and capillary channels are imprinted on plastic substrates and filled by inkjet printing of functional materials into the receivers. The liquid inks move under capillary flow into the adjoining channels, allowing reliable patterning of electronic materials in complex structures with greatly relaxed printing tolerance. Leveraging this process with pristine graphene and ion gel inks, miniaturized all‐solid‐state graphene MSCs are demonstrated to concurrently achieve outstanding resolution (active footprint: <1 mm², minimum feature size: 20 µm) and yield (44/44 devices), while maintaining a high specific capacitance (268 µF cm^–2) and robust stability to extended cycling and bending, establishing an effective route to scale down device size while scaling up production throughput.     

On‐Line Activity Screening for Radical Scavengers from Baccharis chilco

Baccharis plants have been used since ancient times in American traditional medicine. Baccharis chilco is a perennial shrub of temperate regions of South America that grows well in rainfall forests of Colombia. Neither chemical composition nor biological studies of this plant have ever been reported. Two caffeoylquinic acid (CQA) derivatives, 5‐O‐[(E)‐caffeoyl]quinic acid ( 1 ) and 3,5‐di‐O‐[(E)‐caffeoyl]quinic acid ( 3 ), and rosmarinic acid ( 2 ) have been isolated from B. chilco growing wild in Colombia, using the on‐line HPLC‐DAD‐DPPH radical‐scavenging detection technique as guidance. In the course of the purification work, L ‐chiro‐inositol ( 4 ) was also isolated. Structures of the four isolated compounds were determined by spectroscopic methods. Antioxidants 2 and 3 exhibited high antiradical activities evaluated by the 2,2‐diphenyl‐1‐picrylhydrazyl radical (DPPH^.) assay, although somewhat lower than that of the reference compound ascorbic acid. The on‐line HPLC‐DAD‐DPPH technique allowed a rapid pinpointing of antioxidants in the studied EtOH extract, and the facile guided isolation of the target molecules.     

On‐target and nanoparticle‐facilitated selective enrichment of peptides and proteins for analysis by MALDI‐MS

Over the course of the last decade, a number of investigators have come to appreciate that the surface of a MALDI target, after suitable modification, can be used for selective enrichment of peptides and proteins. More recently, surface‐modified nanoparticles (NPs) that readily co‐crystallize in MALDI matrix, are not ionized by laser desorption/ionization, and do not interfere with MS have attracted interest as alternatives to surface‐modified targets for selective enrichment of peptides and proteins. Surface‐modified targets and NPs facilitate parallel processing of samples, and when used in conjunction with MALDI mass spectrometers with kHz lasers enable development of high‐throughput proteomics platforms. Targets and NPs for reversed phase and ion exchange retention, selective enrichment of glycopeptides, selective enrichment of phosphopeptides, and immunoaffinity MS are described in conjunction with details regarding their preparation and utility. Commercial availability of the reagents and substrates required to prepare surface‐modified targets and NPs is also discussed.