Bringing Conducting Polymers to High Order: Toward Conductivities beyond 105 S cm−1 and Thermoelectric Power Factors of 2 mW m−1 K−2

Here, an effective design strategy of polymer thermoelectric materials based on structural control in doped polymer semiconductors is presented. The strategy is illustrated for two archetypical polythiophenes, e.g., poly(2,5‐bis(3‐dodecyl‐2‐thienyl)thieno[3,2‐b]thiophene) (C₁₂‐PBTTT) and regioregular poly(3‐hexylthiophene) (P3HT). FeCl₃ doping of aligned films results in charge conductivities up to 2 × 10⁵ S cm^?1 and metallic‐like thermopowers similar to iodine‐doped polyacetylene. The films are almost optically transparent and show strongly polarized near‐infrared polaronic bands (dichroic ratio >10). The comparative study of structure–property correlations in P3HT and C₁₂‐PBTTT identifies three conditions to obtain conductivities beyond 10⁵ S cm^?1: i) achieve high in‐plane orientation of conjugated polymers with high persistence length; ii) ensure uniform chain oxidation of the polymer backbones by regular intercalation of dopant molecules in the polymer structure without disrupting alignment of π‐stacked layers; and iii) maintain a percolating nanomorphology along the chain direction. The highly anisotropic conducting polymer films are ideal model systems to investigate the correlations between thermopower S and charge conductivity σ. A scaling law S ∝ σ^?1/4 prevails along the chain direction, but a different S ∝ ?ln(σ) relation is observed perpendicular to the chains, suggesting different charge transport mechanisms. The simultaneous increase of charge conductivity and thermopower along the chain direction results in a substantial improvement of thermoelectric power factors up to 2 mW m^?1 K^?2 in C₁₂‐PBTTT.     

Impact of the Doping Method on Conductivity and Thermopower in Semiconducting Polythiophenes

The development of organic semiconductors for use in thermoelectrics requires the optimization of both their thermopower and electrical conductivity. Here two fundamentally different doping mechanisms are used to investigate the thermoelectric properties of known high hole mobility polymers: poly 3‐hexylthiophene (P3HT), poly(2,5‐bis(3‐tetradecylthiophen‐2‐yl)thieno[3,2‐b]thiophene) (PBTTT‐C₁₄), and poly(2,5‐bis(thiphen‐2‐yl)‐(3,7‐diheptadecantyltetrathienoacene)) (P2TDC₁₇‐FT4). The small molecule tetrafluorotetracyanoquinodimethane (F₄TCNQ) is known to effectively dope these polymers, and the thermoelectric properties are studied as a function of the ratio of dopant to polymer repeat unit. Higher electrical conductivity and values of the thermoelectric power factor are achieved by doping with vapor‐deposited fluoroalkyl trichlorosilanes. The combination of these data reveals a striking relationship between thermopower and conductivity in thiophene‐based polymers over a large range of electrical conductivity that is independent of the means of electrical doping. This relationship is not predicted by commonly used transport models for semiconducting polymers and is demonstrated to hold for other semiconducting polymers as well.     

Synergistically Optimizing Electrical and Thermal Transport Properties of BiCuSeO via a Dual‐Doping Approach

The layered oxyselenide BiCuSeO system is known as one of the high‐performance thermoelectric materials with intrinsically low thermal conductivity. By employing atomic, nano‐ to mesoscale structural optimizations, low thermal conductivity coupled with enhanced electrical transport properties can be readily achieved. Upon partial substitution of Bi³⁺ by Ca²⁺ and Pb²⁺, the thermal conductivity can be reduced to as low as 0.5 W m^?1 K^?1 at 873 K through dual‐atomic point‐defect scattering, while a high power factor of ≈1 × 10^?3 W cm^?1 K^?2 is realized over a broad temperature range from 300 to 873 K. The synergistically optimized power factor and intrinsically low thermal conductivity result in a high ZT value of ≈1.5 at 873 K for Bi_0.88Ca_0.06Pb_0.06CuSeO, a promising candidate for high‐temperature thermoelectric applications. It is envisioned that the all‐scale structural optimization is critical for optimizing the thermoelectricity of quaternary compounds.     

High Performance,Flexible, Solid‐State Supercapacitors Based on a Renewable and Biodegradable Mesoporous Cellulose Membrane

A flexible, transparent, and renewable mesoporous cellulose membrane (mCel‐membrane) featuring uniform mesopores of ≈24.7 nm and high porosity of 71.78% is prepared via a facile and scalable solution‐phase inversion process. KOH‐saturated mCel‐membrane as a polymer electrolyte demonstrates a high electrolyte retention of 451.2 wt%, a high ionic conductivity of 0.325 S cm^?1, and excellent mechanical flexibility and robustness. A solid‐state electric double layer capacitor (EDLC) using activated carbon as electrodes, the KOH‐saturated mCel‐membrane as a polymer electrolyte exhibits a high capacitance of 110 F g^?1 at 1.0 A g^?1, and long cycling life of 10 000 cycles with 84.7% capacitance retention. Moreover, a highly integrated planar‐type micro‐supercapacitor (MSC) can be facilely fabricated by directly depositing the electrode materials on the mCel‐membrane‐based polymer electrolyte without using complicated devices. The resulting MSC exhibits a high areal capacitance of 153.34 mF cm^?2 and volumetric capacitance of 191.66 F cm^?3 at 10 mV s^?1, representing one of the highest values among all carbon‐based MSC devices. These findings suggest that the developed renewable, flexible, mesoporous cellulose membrane holds great promise in the practical applications of flexible, solid‐state, portable energy storage devices that are not limited to supercapacitors.     

Outstanding Low Temperature Thermoelectric Power Factor from Completely Organic Thin Films Enabled by Multidimensional Conjugated Nanomaterials

In an effort to create a paintable/printable thermoelectric material, comprised exclusively of organic components, polyaniline (PANi), graphene, and double‐walled nanotube (DWNT) are alternately deposited from aqueous solutions using the layer‐by‐layer assembly technique. Graphene and DWNT are stabilized with an intrinsically conductive polymer, poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS). An 80 quadlayer thin film (≈1 μm thick), comprised of a PANi/graphene‐PEDOT:PSS/PANi/DWNT‐PEDOT:PSS repeating sequence, exhibits unprecedented electrical conductivity (σ ≈ 1.9 × 10⁵ S m^?1) and Seebeck coefficient (S ≈ 120 μV K^?1) for a completely organic material. These two values yield a thermoelectric power factor (PF = S ² σ ^?1) of 2710 μW m^?1 K^?2, which is the highest value ever reported for a completely organic material and among the highest for any material measured at room temperature. These outstanding properties are attributed to the highly ordered structure in the multilayer assembly. This water‐based thermoelectric nanocomposite is competitive with the best inorganic semiconductors (e.g., bismuth telluride) at room temperature and can be applied as a coating to any flexible surface (e.g., fibers in clothing). For the first time, there is a real opportunity to harness waste heat from unconventional sources, such as body heat, to power devices in an environmentally‐friendly way.     

Graphene–Cellulose Paper Flexible Supercapacitors

A simple and scalable method to fabricate graphene‐cellulose paper (GCP) membranes is reported; these membranes exhibit great advantages as freestanding and binder‐free electrodes for flexible supercapacitors. The GCP electrode consists of a unique three‐dimensional interwoven structure of graphene nanosheets and cellulose fibers and has excellent mechanical flexibility, good specific capacitance and power performance, and excellent cyclic stability. The electrical conductivity of the GCP membrane shows high stability with a decrease of only 6% after being bent 1000 times. This flexible GCP electrode has a high capacitance per geometric area of 81 mF cm^?2, which is equivalent to a gravimetric capacitance of 120 F g^?1 of graphene, and retains >99% capacitance over 5000 cycles. Several types of flexible GCP‐based polymer supercapacitors with various architectures are assembled to meet the power‐energy requirements of typical flexible or printable electronics. Under highly flexible conditions, the supercapacitors show a high capacitance per geometric area of 46 mF cm^?2 for the complete devices. All the results demonstrate that polymer supercapacitors made using GCP membranes are versatile and may be used for flexible and portable micropower devices.     

Wearable High‐Performance Supercapacitors Based on Silver‐Sputtered Textiles with FeCo2S4–NiCo2S4 Composite Nanotube‐Built Multitripod Architectures as Advanced Flexible Electrodes

To achieve high‐performance wearable supercapacitors (SCs), a new class of flexible electrodes with favorable architectures allowing large porosity, high conductivity, and good mechanical stability is strongly needed. Here, this study reports the rational design and fabrication of a novel flexible electrode with nanotube‐built multitripod architectures of ternary metal sulfides' composites (FeCo₂S₄–NiCo₂S₄) on a silver‐sputtered textile cloth. Silver sputtering is applicable to almost all kinds of textiles, and S^2? concentration is optimized during sulfidation process to achieve such architectures and also a complete sulfidation assuring high conductivity. New insights into concentration‐dependent sulfidation mechanism are proposed. The additive‐free FeCo₂S₄–NiCo₂S₄ electrode shows a high specific capacitance of 1519 F g^?1 at 5 mA cm^?2 and superior rate capability (85.1% capacitance retention at 40 mA cm^?2). All‐solid‐state SCs employing these advanced electrodes deliver high energy density of 46 W h kg^?1 at 1070 W kg^?1 as well as achieve remarkable cycling stability retaining 92% of initial capacitance after 3000 cycles at 10 mA cm^?2, and outstanding reliability with no capacitance degradation under large twisting. These are attributed to the components' synergy assuring rich redox reactions, high conductivity as well as highly porous but robust architectures. An almost linear increase in capacitance with devices' area indicates possibility to meet various energy output requirements. This work provides a general, low‐cost route to wearable power sources.     

Incorporation of Indium Tin Oxide Nanoparticles in PEMFC Electrodes

Carbon materials suffer from corrosion at the cathode of polymer electrolyte membrane fuel cells (PEMFCs). In the presence of water, carbon support materials are oxidized to carbon dioxide even at low potentials. Hence, nowadays it is very fashionable to look for alternative support materials, like oxides or conductive polymers. To gain the maximum performance for a new material one should also consider an appropriate electrode structure. This study shows the results for the incorporation of nanosized alternative support materials into advanced electrode architectures. Commercially available indium tin oxide (ITO) nanoparticles (<50 nm) are used as support for Pt nanoparticles in combination with Nafion‐coated multi‐walled carbon nanotubes (MWCNTs) on the cathode side of a PEMFC. The MWCNTs promote a high electronic conductivity and help to form a porous network, which could accommodate the Pt/ITO nanoparticles. The microscopic investigations show a homogeneous electrode structure composed of Pt/ITO and MWCNT/Nafion multilayer. Single cell measurements show a maximum power density of 73 mW cm^?2 and a Pt utilization of 1468 mW mg_Pt^?1 for the cathode. The performance data and the Pt utilization are comparable to a standard Pt/carbon black electrode possessing the same Pt loading in the electrode. Beside this, it is shown for the first time that ITO serves as support material under real fuel cell conditions.     

High‐Performance and Breathable Polypyrrole Coated Air‐Laid Paper for Flexible All‐Solid‐State Supercapacitors

High‐performance, breathable, conductive, and flexible polypyrrole (PPy) coated paper electrodes are prepared by an interfacial polymerization method using air‐laid paper as a substrate. Owing to the synergistic effect of superior electrical conductivity, high wettability, and the porous architecture, the prepared electrode not only shows an outstanding specific capacitance and rate abilities (3100 and 2579 mF cm^?2 at 1 and 20 mA cm^?2 for a PPy coated paper electrode), but also exhibits excellent flexibility, wearability, and breathability. Based on these superior features, an all‐solid‐state supercapacitor assembled with the PPy coated paper electrodes shows an outstanding energy density of 62.4 µW h cm^?2, remarkable air permeability and excellent flexibility to sustain various deformations. Furthermore, large‐scale fabrication of conductive flexible paper electrode can be easily achieved through this method. Therefore, this work offers a new vision for flexible energy storage.     

Synergistical Enhancement of Thermoelectric Properties in n‐Type Bi2O2Se by Carrier Engineering and Hierarchical Microstructure

Oxygen‐containing compounds are promising thermoelectric (TE) materials for their chemical and thermal stability. As compared with the high‐performance p‐type counterparts (e.g., ZT ≈1.5 for BiCuSeO), the enhancement of the TE performance of n‐type oxygen‐containing materials remains challenging due to their mediocre electrical conductivity and high thermal conductivity. Here, n‐type layered Bi₂O₂Se is reported as a potential TE material, of which the thermal conductivity and electrical transport properties can be effectively tuned via carrier engineering and hierarchical microstructure. By selective modification of insulating [Bi₂O₂]²⁺ layers with Ta dopant, carrier concentration can be increased by four orders of magnitude (from 10¹⁵ to 10¹⁹ cm^?3) while relatively high carrier mobility can be maintained, thus greatly enhancing the power factors (≈451.5 µW K^?2 m^?1). Meanwhile, the hierarchical microstructure can be induced by Ta doping, and the phonon scattering can be strengthened by atomic point defects, nanodots of 5–10 nm and grains of sub‐micrometer level, which progressively suppresses the lattice thermal conductivity. Accordingly, the ZT value of Bi_1.90Ta_0.10O₂Se reaches 0.36 at 773 K, a ≈350% improvement in comparison with that of the pristine Bi₂O₂Se. The average ZT value of 0.30 from 500 to 823 K is outstanding among n‐type oxygen‐containing TE materials. This work provides a desirable way for enhancing the ZT values in oxygen‐containing compounds.     

Optimization of Electrodeposited p‐Doped Sb2Te3 Thermoelectric Films by Millisecond Potentiostatic Pulses

A systematic optimization of p‐type Sb₂Te₃ thermoelectric films made by potentiostatic electrodeposition on Au and stainless steel substrates is presented. The influence of the preparative parameters of deposition voltage, concentration, and the deposition method are investigated in a nitric acid solution. As a postdeposition step, the influence of annealing the films is investigated. The use of a potential‐controlled millisecond‐pulsed deposition method could improve both the morphology and the composition of the films. The samples are characterized in terms of composition, crystallinity, Seebeck coefficient, and electrical resistivity. Pulsed‐deposited films exhibit Seebeck coefficients of up to 160 μV K^?1 and an electrical conductivity of 280 S cm^?1 at room temperature, resulting in power factors of about 700 μW m^?1 K^?2. After annealing, power factors of maximum 852 μW m^?1 K^?2 are achieved. Although the annealing of DC‐deposited films significantly increased the power factor, they do not reach the values of the pulsed‐deposited films in the preannealing state. Structural analysis is performed with X‐ray diffraction and shows the crystalline structure of Sb₂Te₃ films. The performance is tuned by annealing of deposited films up to 300 °C under He atmosphere while performing in‐situ X‐ray diffraction and resistivity measurements. The chemical analysis of the films is performed by inductively coupled plasma optical emission spectroscopy (ICP‐OES) as well as scanning electron microscope energy dispersive X‐ray analysis (SEM‐EDX).     

Realizing Reversible Conversion‐Alloying of Sb(V) in Polyantimonic Acid for Fast and Durable Lithium‐ and Potassium‐Ion Storage

Finding suitable electrode materials for alkali‐metal‐ion storage is vital to the next‐generation energy‐storage technologies. Polyantimonic acid (PAA, H₂Sb₂O₆ · nH₂O), having pentavalent antimony species and an interconnected tunnel‐like pyrochlore crystal framework, is a promising high‐capacity energy‐storage material. Fabricating electrochemically reversible PAA electrode materials for alkali‐metal‐ion storage is a challenge and has never been reported due to the extremely poor intrinsic electronic conductivity of PAA associated with the highest oxidation state Sb(V). Combining nanostructure engineering with a conductive‐network construction strategy, here is reported a facile one‐pot synthesis protocol for crafting uniform internal‐void‐containing PAA nano‐octahedra in a composite with nitrogen‐doped reduced graphene oxide nanosheets (PAA?N‐RGO), and for the first time, realizing the reversible storage of both Li⁺ and K⁺ ions in PAA?N‐RGO. Such an architecture, as validated by theoretical calculations and ex/in situ experiments, not only fully takes advantage of the large‐sized tunnel transport pathways (0.37 nm²) of PAA for fast solid‐phase ionic diffusion but also leads to exponentially increased electrical conductivity (3.3 S cm^?1 in PAA?N‐RGO vs 4.8 × 10^?10 S cm^?1 in bare‐PAA) and yields an inside‐out buffer function for accommodating volume expansion. Compared to electrochemically irreversible bare‐PAA, PAA?N‐RGO manifests reversible conversion‐alloying of Sb(V) toward fast and durable Li⁺‐ and K⁺‐ion storage.     

High‐Performance Thermoelectric Paper Based on Double Carrier‐Filtering Processes at Nanowire Heterojunctions

As commercial interest in flexible power‐conversion devices increases, the demand for high‐performance alternatives to brittle inorganic thermoelectric (TE) materials is growing. As an alternative, we propose a rationally designed graphene/polymer/inorganic nanocrystal free‐standing paper with high TE performance, high flexibility, and mechanical/chemical durability. The ternary hybrid system of the graphene/polymer/inorganic nanocrystal includes two hetero­junctions that induce double‐carrier filtering, which significantly increases the electrical conductivity without a major decrease in the thermopower. The ternary hybrid shows a power factor of 143 μW m^?1 K^?1 at 300 K, which is one to two orders of magnitude higher than those of single‐ or binary‐component materials. In addition, with five hybrid papers and polyethyleneimine (PEI)‐doped single‐walled carbon nanotubes (SWCNTs) as the p‐type and n‐type TE units, respectively, a maximum power density of 650 nW cm^?2 at a temperature difference of 50 K can be obtained. The strategy proposed here can improve the performance of flexible TE materials by introducing more heterojunctions and optimizing carrier transfer at those junctions, and shows great potential for the preparation of flexible or wearable power‐conversion devices.     

A Cu‐Based Nanoparticulate Film as Super‐Active and Robust Catalyst Surpasses Pt for Electrochemical H2 Production from Neutral and Weak Acidic Aqueous Solutions

Electrocatalysts that are stable and highly active at low overpotential (η) under mild conditions as well as cost‐effective and scalable are eagerly desired for potential use in photo‐ and electro‐driven hydrogen evolution devices. Here the fabrication and characterization of a super‐active and robust Cu‐Cu_xO‐Pt nanoparticulate electrocatalyst is reported, which displays a small Tafel slope (44 mV dec^?1) and a large exchange current density (1.601 mA cm^?2) in neutral buffer solution. The catalytic current density of this catalyst film reaches 500 mA cm^?2 at η = ?390 ± 12 mV and 20 mA cm^?2 at η = ?45 ± 3 mV, which are significantly higher than the values displayed by Pt foil and Pt/C electrodes in neutral buffer solution and even comparable with the activity of Pt electrode in 0.5 m H₂SO₄ solution.     

Inverted Tandem Polymer Solar Cells with Polyethylenimine‐Modified MoOX/Al2O3:ZnO Nanolaminate as the Charge Recombination Layers

A new charge recombination layer for inverted tandem polymer solar cells is reported. A bilayer of MoO_X/Al₂O₃:ZnO nanolaminate is shown to enable efficient charge recombination in inverted tandem cells. A polymer surface modification on the MoO_X/Al₂O₃:ZnO nanolaminate bilayer increases the work function contrast between the two outward surfaces of the charge recombination layer, further improving the performance of tandem solar cells. An analysis of the electrical, optical, and surface properties of the charge recombination layer is presented. Inverted tandem polymer solar cells, with two photoactive layers comprising poly (3‐hexylthiophene) (P3HT):indene‐C₆₀ bisadduct (IC₆₀BA) for the bottom cell and poly[(4,8‐bis‐(2‐ethylhexyloxy)‐benzo[1,2‐b:4,5‐b']dithiophene)‐2,6‐diyl‐alt‐(4‐(2‐ethylhexanoyl)‐thieno[3,4‐b]thiophene))‐2,6‐diyl] (PBDTTT‐C):[6,6]‐phenyl C₆₁ butyric acid methyl ester (PC₆₀BM) for the top cell, yield an open‐circuit voltage of 1481 mV ± 15 mV, a short‐circuit current density of 7.1 mA cm^?2 ± 0.1 mA cm^?2, and a fill factor of 0.62 ± 0.01, resulting in a power conversion efficiency of 6.5% ± 0.1% under simulated AM 1.5G, 100 mW cm^?2 illumination.     

Battery‐like Supercapacitors from Vertically Aligned Carbon Nanofiber Coated Diamond: Design and Demonstrator

To fabricate battery‐like supercapacitors with high power and energy densities, big capacitances, as well as long‐term capacitance retention, vertically aligned carbon nanofibers (CNFs) grown on boron doped diamond (BDD) films are employed as the capacitor electrodes. They possess large surface areas, high conductivity, high stability, and importantly are free of binder. The large surface areas result from their porous structures. The containment of graphene layers and copper metal catalysts inside CNFs leads to their high conductivity. Both electrical double layer capacitors (EDLCs) in inert solutions and pseudocapacitors (PCs) using Fe(CN)₆^3?/4? redox‐active electrolytes are constructed with three‐ and two‐electrode systems. The assembled two‐electrode symmetrical supercapacitor devices exhibit capacitances of 30 and 48 mF cm^?2 at 10 mV s^?1 for EDLC and PC devices, respectively. They remain constant even after 10 000 charging/discharging cycles. The power densities are 27.3 and 25.3 kW kg^?1 for EDLC and PC devices, together with their energy densities of 22.9 and 44.1 W h kg^?1, respectively. The performance of these devices is superior to most of the reported supercapacitors and batteries. Vertically aligned CNF/BDD hybrid films are thus useful to construct high‐performance battery‐like and industry‐orientated supercapacitors for future power devices.     

Flexible Quasi‐Solid State Ionogels with Remarkable Seebeck Coefficient and High Thermoelectric Properties

Thermoelectric materials can be used to harvest low‐grade heat that is otherwise dissipated to the environment. But the conventional thermoelectric materials that are semiconductors or semimetals, usually exhibit a Seebeck coefficient of much less than 1 mV K^?1. They are expensive and consist of toxic elements as well. Here, it is demonstrated environmental benign flexible quasi‐solid state ionogels with giant Seebeck coefficient and ultrahigh thermoelectric properties. The ionogels made of ionic liquids and poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVDF‐HFP) can exhibit a giant Seebeck coefficient up to 26.1 mV K^?1, the highest for electronic and ionic conductors. In addition, they have a high ionic conductivity of 6.7 mS cm^?1 and a low thermal conductivity of 0.176 W m^?1 K^?1. Their thermoelectric figure of merit (ZT) is thus 0.75. The giant Seebeck coefficient is related to the ion‐dipole interaction between PVDF‐HFP and ionic liquids. Their application in ionic thermoelectric capacitors is also demonstrated for the conversion of intermittent heat into electricity. They are especially important to harvest the low‐grade thermal energy that is abundant on earth.     

A High‐Performance Composite Electrode for Vanadium Redox Flow Batteries

A composite electrode composed of reduced graphene oxide‐graphite felt (rGO‐GF) with excellent electrocatalytic redox reversibility toward V²⁺/V³⁺ and VO²⁺/VO₂⁺ redox couples in vanadium batteries was fabricated by a facile hydrothermal method. Compared with the pristine graphite felt (GF) electrode, the rGO‐GF composite electrode possesses abundant oxygen functional groups, high electron conductivity, and outstanding stability. Its corresponding energy efficiency and discharge capacity are significantly increased by 20% and 300%, respectively, at a high current density of 150 mA cm^?2. Moreover, a discharge capacity of 20 A h L^?1 is obtained with a higher voltage efficiency (74.5%) and energy efficiency (72.0%), even at a large current density of 200 mA cm^?2. The prepared rGO‐GF composite electrode holds great promise as a high‐performance electrode for vanadium redox flow battery (VRFB).     

Highly Reversible Na Storage in Na3V2(PO4)3 by Optimizing Nanostructure and Rational Surface Engineering

Sodium‐ion batteries (NIBs) have attracted more and more attention as economic alternatives for lithium‐ion batteries (LIBs). Sodium super ionic conductor (NASICON) structure materials, known for high conductivity and chemical diffusion coefficient of Na⁺ (≈10^?14 cm² s^?1), are promising electrode materials for NIBs. However, NASICON structure materials often suffer from low electrical conductivity (<10^?4 S cm^?1), which hinders their electrochemical performance. Here high performance sodium storage performance in Na₃V₂(PO₄)₃ (NVP) is realized by optimizing nanostructure and rational surface engineering. A N, B codoped carbon coated three‐dimensional (3D) flower‐like Na₃V₂(PO₄)₃ composite (NVP@C‐BN) is designed to enable fast ions/electrons transport, high‐surface controlled energy storage, long‐term structural integrity, and high‐rate cycling. The conductive 3D interconnected porous structure of NVP@C‐BN greatly releases mechanical stress from Na⁺ extraction/insertion. In addition, extrinsic defects and active sites introduced by the codoping heteroatoms (N, B) both enhance Na⁺ and e^? diffusion. The NVP@C‐BN displays excellent electrochemical performance as the cathode, delivering reversible capacity of 70% theoretical capacity at 100 C after 2000 cycles. When used as anode, the NVP@C‐BN also shows super long cycle life (38 mA h g^?1 at 20 C after 5000 cycles). The design provides a novel approach to open up possibilities for designing high‐power NIBs.     

A High‐Energy Density Asymmetric Supercapacitor Based on Fe2O3 Nanoneedle Arrays and NiCo2O4/Ni(OH)2 Hybrid Nanosheet Arrays Grown on SiC Nanowire Networks as Free‐Standing Advanced Electrodes

In this paper, a novel freestanding core‐branch negative and positive electrode material through integrating trim aligned Fe₂O₃ nanoneedle arrays (Fe₂O₃ NNAs) is first proposed with typical mesoporous structures and NiCo₂O₄/Ni(OH)₂ hybrid nanosheet arrays (NiCo₂O₄/Ni(OH)₂ HNAs) on SiC nanowire (SiC NW) skeletons with outstanding resistance to oxidation and corrosion, good conductivity, and large‐specific surface area. The original built SiC NWs@Fe₂O₃ NNAs is validated to be a highly capacitive negative electrode (721 F g^?1 at 2 A g^?1, i.e., 1 F cm^?2 at 2.8 mA cm^?2), matching well with the similarly constructed SiC NWs@NiCo₂O₄/Ni(OH)₂ HNAs positive electrode (2580 F g^?1 at 4 A g^?1, i.e., 3.12 F cm^?2 at 4.8 mA cm^?2). Contributed by the uniquely engineered electrodes, a high‐performance asymmetric supercapacitor (ASC) is developed, which can exhibit a maximum energy density of 103 W h kg^?1 at a power density of 3.5 kW kg^?1, even when charging the device within 6.5 s, the energy density can still maintain as high as 45 W h kg^?1 at 26.1 kW kg^?1, and the ASC manifests long cycling lifespan with 86.6% capacitance retention even after 5000 cycles. This pioneering work not only offers an attractive strategy for rational construction of high‐performance SiC NW‐based nanostructured electrodes materials, but also provides a fresh route for manufacturing next‐generation high‐energy storage and conversion systems.