Improve the Performance of the All‐Small‐Molecule Nonfullerene Organic Solar Cells through Enhancing the Crystallinity of Acceptors

Significant development has been achieved in nonfullerene organic solar cells. However, most of the high‐efficiency nonfullerene systems are composed of polymer donors and fused‐ring acceptors, and only a few small molecule donors can work well. Herein, a new A–D–A small molecule donor named NDTSR with naphtho[1,2‐b:5,6‐b′]dithiophene (NDT) as building blocks is synthesized. Two energy levels well‐matched fused‐ring acceptors ITIC and IDIC are chosen to construct all‐small‐molecule solar cells with NDTSR, respectively. When mixed with IDIC, a high power conversion efficiency (PCE) of 8.05% is achieved, which is the highest efficiency for NDT‐based small molecule donor. However, the NDTSR:ITIC system only exhibits a low PCE of 1.77%. The big difference in the performance of these two systems should be attributed to the different morphology and phase separation resulting from the crystallinity and aggregation ability of the acceptors. The results demonstrate that NDT‐based small molecule is a promising candidate donor for all‐small‐molecule systems, while the crystallinity of fused‐ring acceptors is a critical factor for optimizing the phase separation in the active layer.     

Effect of Ring‐Fusion on Miscibility and Domain Purity: Key Factors Determining the Performance of PDI‐Based Nonfullerene Organic Solar Cells

Compared to the rapid development of nonfullerene organic solar cells (OSCs) based on the state‐of‐the‐art indacenodithiophene (IDT)‐based small molecule acceptors (SMAs), the progress for perylene diimide (PDI)‐based electron acceptors has lagged behind owing to the lack of understanding on the structure–morphology–performance relationship of PDI SMAs. Given the ease of synthesis for PDIs and their high intrinsic electron mobility, it is crucial to identify key material parameters that influence the polymer:PDI blend morphology and to develop rational approaches for molecular design toward high‐performance PDI‐based SMAs. In this study, three pairs of PDI‐based SMAs with and without ring‐fusion are investigated and it is found that ring‐fusion and domain purity are the key structural and morphological factors determining the fill factors (FFs) and efficiencies of PDI‐based nonfullerene OSCs. This data shows that nonfullerene OSCs based on the ring‐fused PDI‐based SMAs exhibit much higher average domain purity and thus increased charge mobilities, which lead to enhanced FFs compared to those solar cells based on nonfused PDIs. This is explained by higher Florry Huggins interaction parameters as observed by melting point depression measurements. This study suggests that increasing repulsive molecular interactions to lower the miscibility between the polymer donor and PDI acceptor is the key to improve the FF and performance of PDI‐based devices.     

Modulation of End Groups for Low‐Bandgap Nonfullerene Acceptors Enabling High‐Performance Organic Solar Cells

The field of nonfullerene organic solar cells (OSCs) has seen an impressive progress, largely due to advances in high‐performance small molecule acceptors (SMAs). As a large portion of the solar energy is located in the near‐infrared region, it is important to develop ultralow‐bandgap SMAs that have extended absorption in the spectral range of 800–1000 nm to maximize light absorption and efficiencies. In this work, three low‐bandgap SMAs, namely, IXIC, IXIC‐2Cl, and IXIC‐4Cl, are designed and synthesized with same fused terthieno[3,2‐b]thiophene donor unit and different end groups (EGs). The three SMAs all have low optical bandgap (E_g) of 1.35, 1.30, and 1.25 eV, respectively. The chlorination on EGs can lower the energy level and broaden absorption range of the SMAs. As a result, the V_oc of the devices is reduced but the J_sc is significantly increased. In addition, the addition of chlorine atoms can enhance π–π stacking and crystallinity of the SMAs, which result in high fill factors. Overall, the optimum EGs are monochlorine‐substituted IC and OSCs based on PBDB‐T:IXIC‐2Cl that can achieve remarkable power conversion efficiencies (PCEs) of 12.2%, which is one of the highest PCEs for nonfullerene organic solar cells based on low‐bandgap SMAs.     

The Physics of Small Molecule Acceptors for Efficient and Stable Bulk Heterojunction Solar Cells

Organic bulk heterojunction solar cells based on small molecule acceptors have recently seen a rapid rise in the power conversion efficiency with values exceeding 13%. This impressive achievement has been obtained by simultaneous reduction of voltage and charge recombination losses within this class of materials as compared to fullerene‐based solar cells. In this contribution, the authors review the current understanding of the relevant photophysical processes in highly efficient nonfullerene acceptor (NFA) small molecules. Charge generation, recombination, and charge transport is discussed in comparison to fullerene‐based composites. Finally, the authors review the superior light and thermal stability of nonfullerene small molecule acceptor based solar cells, and highlight the importance of NFA‐based composites that enable devices without early performance loss, thus resembling so‐called burn‐in free devices.     

Constructing High‐Performance All‐Small‐Molecule Ternary Solar Cells with the Same Third Component but Different Mechanisms for Fullerene and Non‐fullerene Systems

Two types of all‐small‐molecule ternary solar cells consisting of two small‐molecule donors and one acceptor (fullerene/non‐fullerene) are developed. Interestingly, both these devices have a common component: a carefully designed medium bandgap small molecule, which possesses appropriate energy levels and displays good compatibility with the host donor. In the fullerene system, the charge‐relaying role of the additive donor is confirmed by the improved charge transportation and suppressed charge recombination. While in the non‐fullerene system, the mixed face‐on and edge‐on orientation of the ternary film induced by the additive donor dominates the promotion of charge transportation. Accordingly, both ternary devices deliver higher short‐circuit current density, fill factor, and power conversion efficiencies of over 10% compared to binary ones. This work offers a promising guideline on the construction of high‐performance all‐small‐molecule ternary solar cells by incorporating a miscible small‐molecule donor.     

Influence of Donor Polymer on the Molecular Ordering of Small Molecular Acceptors in Nonfullerene Polymer Solar Cells

Nonfullerene polymer solar cells (PSCs) based on polymer donors and nonfullerene small molecular acceptors (SMAs) have recently attracted considerable attention. Although much of the progress is driven by the development of novel SMAs, the donor polymer also plays an important role in achieving efficient nonfullerene PSCs. However, it is far from clear how the polymer donor choice influences the morphology and performance of the SMAs and the nonfullerene blends. In addition, it is challenging to carry out quantitative analysis of the morphology of polymer:SMA blends, due to the low material contrast and overlapping scattering features of the π–π stacking between the two organic components. Here, a series of nonfullerene blends is studied based on ITIC‐Th blended with five different donor polymers. Through quantitative morphology analysis, the (010) coherence length of the SMA is characterized and a positive correlation between the coherence length of the SMA and the device fill factor (FF) is established. The study reveals that the donor polymer can significantly change the molecular ordering of the SMA and thus improve the electron mobility and domain purity of the blend, which has an overall positive effect that leads to the enhanced device FF for nonfullerene PSCs.     

High Performance Thick‐Film Nonfullerene Organic Solar Cells with Efficiency over 10% and Active Layer Thickness of 600 nm

Developing efficient organic solar cells (OSCs) with relatively thick active layer compatible with the roll to roll large area printing process is an inevitable requirement for the commercialization of this field. However, typical laboratory OSCs generally exhibit active layers with optimized thickness around 100 nm and very low thickness tolerance, which cannot be suitable for roll to roll process. In this work, high performance of thick‐film organic solar cells employing a nonfullerene acceptor F–2Cl and a polymer donor PM6 is demonstrated. High power conversion efficiencies (PCEs) of 13.80% in the inverted structure device and 12.83% in the conventional structure device are achieved under optimized conditions. PCE of 9.03% is obtained for the inverted device with active layer thickness of 500 nm. It is worth noting that the conventional structure device still maintains the PCE of over 10% when the film thickness of the active layer is 600 nm, which is the highest value for the NF‐OSCs with such a large active layer thickness. It is found that the performance difference between the thick active layer films based conventional and inverted devices is attributed to their different vertical phase separation in the active layers.     

Printed Nonfullerene Organic Solar Cells with the Highest Efficiency of 9.5%

The current work reports a high power conversion efficiency (PCE) of 9.54% achieved with nonfullerene organic solar cells (OSCs) based on PTB7‐Th donor and 3,9‐bis(2‐methylene‐(3‐(1,1‐dicyanomethylene)‐indanone))‐5,5,11,11‐tetrakis(4‐hexylphenyl)‐dithieno[2,3‐d:2′,3′‐d′]‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene) (ITIC) acceptor fabricated by doctor‐blade printing, which has the highest efficiency ever reported in printed nonfullerene OSCs. Furthermore, a high PCE of 7.6% is realized in flexible large‐area (2.03 cm²) indium tin oxide (ITO)‐free doctor‐bladed nonfullerene OSCs, which is higher than that (5.86%) of the spin‐coated counterpart. To understand the mechanism of the performance enhancement with doctor‐blade printing, the morphology, crystallinity, charge recombination, and transport of the active layers are investigated. These results suggest that the good performance of the doctor‐blade OSCs is attributed to a favorable nanoscale phase separation by incorporating 0.6 vol% of 1,8‐diiodooctane that prolongs the dynamic drying time of the doctor‐bladed active layer and contributes to the migration of ITIC molecules in the drying process. High PCE obtained in the flexible large‐area ITO‐free doctor‐bladed nonfullerene OSCs indicates the feasibility of doctor‐blade printing in large‐scale fullerene‐free OSC manufacturing. For the first time, the open‐circuit voltage is increased by 0.1 V when 1 vol% solvent additive is added, due to the vertical segregation of ITIC molecules during solvent evaporation.     

Nonfullerene n‐Type Organic Semiconductors for Perovskite Solar Cells

Compared to inorganic semiconductors and/or fullerene derivatives, nonfullerene n‐type organic semiconductors present some advantages, such as low‐temperature processing, flexibility, and molecule structure diversity, and have been widely used in perovskite solar cells (PSCs). In this research news article, the recent advances in nonfullerene n‐type organic semiconductors which function as electron‐transporting, interface‐modifying, additive, and light‐harvesting materials in PSCs are summarized. The remaining challenges and promising future directions of nonfullerene‐based PSCs are also discussed.     

Asymmetric Nonfullerene Small Molecule Acceptors for Organic Solar Cells

Symmetry breaking provides a new material design strategy for nonfullerene small molecule acceptors (SMAs). The past 10 years have witnessed significant advances in asymmetric nonfullerene SMAs in organic solar cells (OSCs) with power conversion efficiency (PCE) increasing from ≈1% to ≈14%. In this review, the progress of asymmetric nonfullerene SMAs, including early reports of asymmetric nonfullerene SMAs, asymmetric PDI‐based nonfullerene SMAs, and asymmetric acceptor–donor–acceptor (A–D–A)‐type nonfullerene SMAs, is summarized. The structure–property relationships and the perspectives for future development of asymmetric nonfullerene SMAs are also discussed.     

Simultaneous Enhancement of Three Parameters of P3HT‐Based Organic Solar Cells with One Oxygen Atom

Poly(3‐hexylthiophene) (P3HT)‐based organic solar cells (OSCs) have attracted much attention due to their advantages of low‐cost production and matured roll‐to‐roll manufacture. However, the efficiency of P3HT‐based OSCs lag much behind the non‐P3HT ones due to their negligible absorption of long wavelengths of light over 650 nm, high‐lying highest occupied molecular orbitals (HOMO), and difficulty of controlling morphology. In this study, the alkyl chains of the nonfullerene acceptors are replaced with alkoxy chains to achieve synergistic enhancement of all three parameters ( short circuit current density (J_SC), open circuit voltage (V_OC), and fill factor (FF)) and thus significant increase of power conversion efficiency for P3HT‐based OSCs. As a result, the OSCs exhibit a maxima efficiency of 6.6%. The P3HT‐based systems are systematically studied with optical spectroscopy, photoluminescence, cyclic voltametry, space charge limit current, grazing incident wide‐angle X‐ray scattering, transient absorption spectroscopy, transmission electron microscope, and atomic force microscopy to probe the mechanism, which reveal that introducing alkoxy chains simultaneously increases the energy levels of the HOMO and the lowest unoccupied molecular orbitals, enhances the light absorption, improves the rigidity of the backbone and charge transport mobility, and tunes the molecular orientation and film morphology, thus improving the photovoltaic performance. This contribution provides an important guidance in the design of novel nonfullerene acceptors for high‐performance P3HT‐based OSCs.     

Effects of Solvent Additives on Morphology,Charge Generation,Transport, and Recombination in Solution‐Processed Small‐Molecule Solar Cells

The effects of solvent additive (1,8‐diiodooctane (DIO)) on the morphology, charge generation, transport, and recombination in solution‐processed small‐molecule solar cells are studied and these parameters are correlated with device performance. In the optimum nanoscale morphology, which is processed with 0.4% DIO, the phase separation is large enough to create a percolating pathway for carrier transport, yet still small enough to form large interfacial area for efficient charge separation. Complete phase separation in this film reduces the interfacial defects, which occurs without DIO, and hence suppresses the monomolecular recombination. Moreover, balanced charge transport and weak bimolecular recombination lead to a high fill factor (72%). On the other hand, an excess amount of DIO (0.8%) in the solvent results in the over‐aggregation of the donor phase, which disturbs the percolating pathway of the acceptor phase and reduces the electron mobility. The over‐aggregation of the donor phase also shrinks the interfacial area for charge separation and consequently reduces the photocurrent generation.     

Polymer Main‐Chain Substitution Effects on the Efficiency of Nonfullerene BHJ Solar Cells

“Nonfullerene” acceptors are proving effective in bulk heterojunction (BHJ) solar cells when paired with selected polymer donors. However, the principles that guide the selection of adequate polymer donors for high‐efficiency BHJ solar cells with nonfullerene acceptors remain a matter of some debate and, while polymer main‐chain substitutions may have a direct influence on the donor–acceptor interplay, those effects should be examined and correlated with BHJ device performance patterns. This report examines a set of wide‐bandgap polymer donor analogues composed of benzo[1,2‐b:4,5‐b′]dithiophene (BDT), and thienyl ([2H]T) or 3,4‐difluorothiophene ([2F]T) motifs, and their BHJ device performance pattern with the nonfullerene acceptor “ITIC”. Studies show that the fluorine‐ and ring‐substituted derivative PBDT(T)[2F]T largely outperforms its other two polymer donor counterparts, reaching power conversion efficiencies as high as 9.8%. Combining several characterization techniques, the gradual device performance improvements observed on swapping PBDT[2H]T for PBDT[2F]T, and then for PBDT(T)[2F]T, are found to result from (i) notably improved charge generation and collection efficiencies (estimated as ≈60%, 80%, and 90%, respectively), and (ii) reduced geminate recombination (being suppressed from ≈30%, 25% to 10%) and bimolecular recombination (inferred from recombination rate constant comparisons). These examinations will have broader implications for further studies on the optimization of BHJ solar cell efficiencies with polymer donors and a wider range of nonfullerene acceptors.     

Alkyl Chain Engineering of Solution‐Processable Star‐Shaped Molecules for High‐Performance Organic Solar Cells

The impact of alkyl side‐chain substituents on conjugated polymers on the photovoltaic properties of bulk heterojunction (BHJ) solar cells has been studied extensively, but their impact on small molecules has not received adequate attention. To reveal the effect of side chains, a series of star‐shaped molecules based on a triphenylamine (TPA) core, bithiophene, and dicyanovinyl units derivatized with various alkyl end‐capping groups of methyl, ethyl, hexyl and dodecyl is synthesiyed and studied to comprehensively investigate structure‐properties relationships. UV‐vis absorption and cyclic voltammetry data show that variations of alkyl chain length have little influence on the absorption and highest occupied molecular orbital (HOMO)‐lowest unoccupied molecular orbital (LUMO) levels. However, these seemingly negligible changes have a pronounced impact on the morphology of BHJ thin films as well as their charge carrier separation and transportation, which in turn influences the photovoltaic properties of these small‐molecule‐based BHJ devices. Solution‐processed organic solar cells (OSCs) based on the small molecule with the shortest methyl end groups exhibit high short circuit current (J_sc) and fill factor (FF), with an efficiency as high as 4.76% without any post‐treatments; these are among the highest reported for solution‐processed OSCs based on star‐shaped molecules.     

Efficient Ternary Polymer Solar Cells with Two Well‐Compatible Donors and One Ultranarrow Bandgap Nonfullerene Acceptor

Nonfullerene polymer solar cells (PSCs) are fabricated by using one wide bandgap donor PBDB‐T and one ultranarrow bandgap acceptor IEICO‐4F as the active layers. One medium bandgap donor PTB7‐Th is selected as the third component due to the similar highest occupied molecular orbital level compared to that of PBDB‐T and their complementary absorption spectra. The champion power conversion efficiency (PCE) of PSCs is increased from 10.25% to 11.62% via incorporating 20 wt% PTB7‐Th in donors, with enhanced short‐circuit current (J_SC) of 24.14 mA cm^?2 and fill factor (FF) of 65.03%. The 11.62% PCE should be the highest value for ternary nonfullerene PSCs. The main contribution of PTB7‐Th can be summarized as the improved photon harvesting and enhanced exciton utilization of PBDB‐T due to the efficient energy transfer from PBDB‐T to PTB7‐Th. Meanwhile, PTB7‐Th can also act as a regulator to adjust PBDB‐T molecular arrangement for optimizing charge transport, resulting in the enhanced FF of ternary PSCs. This experimental result may provide new insight for developing high‐performance ternary nonfullerene PSCs by selecting two well‐compatible donors with different bandgap and one ultranarrow bandgap acceptor.     

Boosting Organic–Metal Oxide Heterojunction via Conjugated Small Molecules for Efficient and Stable Nonfullerene Polymer Solar Cells

Charge events across organic–metal oxide heterointerfaces routinely occur in organic electronics, yet strongly influence their overall performance and stability. They become even more complicated and challenging for the heterojunction conditions in polymer solar cells (PSCs), especially when nonfullerene acceptors with varied energetics are employed. In this work, an effective interfacial strategy that utilizes novel small molecule self‐assembled monolayers (SAMs) is developed to improve the electronic and electric, as well as chemical properties of organic–zinc oxide (ZnO) interfaces for nonfullerene PSCs. It is revealed that the tailored SAMs with well‐controlled energy levels and molecular dipoles can effectively optimize the energetic barrier and work function (WF) of heterointerface for optimal electron extraction. In addition, the introduction of SAMs atop of ZnO facilitates not only acceptor segregation near the n‐contact interface, but also passivation of the photocatalytic activities for ZnO, to improve overall performance and photo stability of the derived nonfullerene PSCs. Overall, the methodology and structure–property relationship revealed herein would be beneficial for a wide range of hybrid electronics.     

Achieving Balanced Crystallization Kinetics of Donor and Acceptor by Sequential‐Blade Coated Double Bulk Heterojunction Organic Solar Cells

Sequential deposition has great potential to achieve high performance in organic solar cells due to the resulting well‐controlled vertical phase separation. In this work, double bulk heterojunction organic solar cells are fabricated by sequential‐blade cast in ambient conditions. Probed by the in situ grazing incidence X‐ray diffraction and in situ UV–vis absorption measurements, the seq‐blade system exhibits a different tendency from each of the binary films during the film formation process. Due to the extensive aggregation of FOIC, the binary PBDB‐T:FOIC film displays a strong and large phase separation, resulting in low current density (J_sc) and unsatisfactory power conversion efficiency. In the seq‐blade cast system, the bottom layer PBDB‐T:IT‐M produces many crystal nuclei for the top layer PBDB‐T:FOIC, so the PBDB‐T molecules are able to crystallize easily and quickly. Balanced crystallization kinetics between polymer and small molecule and an ideal percolation network in the film are observed. In addition, the balanced crystallization kinetics are favorable toward realizing lower recombination loss through charge transport processes.     

Overcoming Interfacial Losses in Solution‐Processed Organic Multi‐Junction Solar Cells

Organic solar cells are promising in terms of full‐solution‐processing which enables low‐cost and large‐scale fabrication. While single‐junction solar cells have seen a boost in power conversion efficiency (PCE), multi‐junction solar cells are promising to further enhance the PCE. In all‐solution‐processed multi‐junction solar cells, interfacial losses are often encountered between hole‐transporting layer (HTL) and the active layers and therefore greatly limit the application of newly developed high‐performance donor and acceptor materials in multi‐junction solar cells. Here, the authors report on a systematic study of interface losses in both single‐junction and multi‐junction solar cells based on representative polymer donors and HTLs using electron spectroscopy and time‐of‐flight secondary ion mass spectrometry. It is found that a facile mixed HTL containing poly(3,4‐ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) and MoO _x nanoparticles successfully overcomes the interfacial losses in both single‐ and multi‐junction solar cells based on various active layers by reducing interface protonation, promoting better energy‐level alignment, and forming a dense and smooth layer. Solution‐processed single‐junction solar cells are demonstrated to reach the same performance as with evaporated MoO _x (over 7%). Multi‐junction solar cells with polymers containing nitrogen atoms as the first layer and the mixed PEDOT:PSS and MoO _x nanoparticles as hole extraction layer reach fill factor (FF) of over 60%, and PCE of over 8%, while the identical stack with pristine PEDOT:PSS or MoO _x nanoparticles show FF smaller than 50% and PCE less than 5%.     

Thermally Stable All‐Polymer Solar Cells with High Tolerance on Blend Ratios

Tuning the blend composition is an essential step to optimize the power conversion efficiency (PCE) of organic bulk heterojunction (BHJ) solar cells. PCEs from devices of unoptimized donor:acceptor (D:A) weight ratio are generally significantly lower than optimized devices. Here, two high‐performance organic nonfullerene BHJ blends PBDB‐T:ITIC and PBDB‐T:N2200 are adopted to investigate the effect of blend ratio on device performance. It is found that the PCEs of polymer‐polymer (PBDB‐T:N2200) blend are more tolerant to composition changes, relative to polymer‐molecule (PBDB‐T:ITIC) devices. In both systems, short‐circuit current density (J_sc) is tracked closely with PCE, indicating that exciton dissociation and transport strongly influence PCEs. With dilute acceptor concentrations, polymer‐polymer blends maintain high electron mobility relative to the polymer‐molecule blends, which explains the dramatic difference in PCEs between them as a function of D:A blend ratio. In addition, polymer‐polymer solar cells, especially at high D:A blend ratio, are stable (less than 5% relative loss) over 70 d under continuous heating at 80 °C in a glovebox without encapsulation. This work demonstrates that all‐polymer solar cells show advantage in operational lifetime under thermal stress and blend‐ratio resilience, which indicates their high potential for designing of stable and scalable solar cells.     

3,4‐Dicyanothiophene—a Versatile Building Block for Efficient Nonfullerene Polymer Solar Cells

In this contribution, a versatile building block, 3,4‐dicyanothiophene (DCT), which possesses structural simplicity and synthetic accessibility for constructing high‐performance, low‐cost, wide‐bandgap conjugated polymers for use as donors in polymer solar cells (PSCs), is reported. A prototype polymer, PB3TCN‐C66, and its cyano‐free analogue polymer PB3T‐C66, are synthesized to evaluate the potential of using DCT in nonfullerene PSCs. A stronger aggregation property in solution, higher thermal transition temperatures with higher enthalpies, a larger dipole moment, higher relative dielectric constant, and more linear conformation are exhibited by PB3TCN‐C66. Solar cells employing IT‐4F as the electron acceptor offer power conversion efficiencies (PCEs) of 11.2% and 2.3% for PB3TCN‐C66 and PB3T‐C66, respectively. Morphological characterizations reveal that the PB3TCN‐C66:IT‐4F blend exhibits better π–π paracrystallinity, a contracted domain size, and higher phase purity, consistent with its higher molecular interaction parameter, derived from thermodynamic calculations. Moreover, PB3TCN‐C66 offers a higher open‐circuit voltage and reduced energy loss than most state‐of‐the‐art wide‐bandgap polymers, without the need of additional electron‐withdrawing substituents. Two additional polymers derived from DCT also demonstrate promising performance with a higher PCE of 13.4% being achieved. Thus, DCT represents a versatile and promising building block for constructing high‐performance, low‐cost, conjugated polymers for application in PSCs.