Molecular Engineering Using an Anthanthrone Dye for Low‐Cost Hole Transport Materials: A Strategy for Dopant‐Free,High‐Efficiency,and Stable Perovskite Solar Cells

In this report, highly efficient and humidity‐resistant perovskite solar cells (PSCs) using two new small molecule hole transporting materials (HTM) made from a cost‐effective precursor anthanthrone (ANT) dye, namely, 4,10‐bis(1,2‐dihydroacenaphthylen‐5‐yl)‐6,12‐bis(octyloxy)‐6,12‐dihydronaphtho[7,8,1,2,3‐nopqr]tetraphene (ACE‐ANT‐ACE) and 4,4′‐(6,12‐bis(octyloxy)‐6,12‐dihydronaphtho[7,8,1,2,3‐nopqr]tetraphene‐4,10‐diyl)bis(N,N‐bis(4‐methoxyphenyl)aniline) (TPA‐ANT‐TPA) are presented. The newly developed HTMs are systematically compared with the conventional 2,2′,7,7′‐tetrakis(N,N′‐di‐p‐methoxyphenylamino)‐9,9′‐spirbiuorene (Spiro‐OMeTAD). ACE‐ANT‐ACE and TPA‐ANT‐TPA are used as a dopant‐free HTM in mesoscopic TiO₂/CH₃NH₃PbI₃/HTM solid‐state PSCs, and the performance as well as stability are compared with Spiro‐OMeTAD‐based PSCs. After extensive optimization of the metal oxide scaffold and device processing conditions, dopant‐free novel TPA‐ANT‐TPA HTM‐based PSC devices achieve a maximum power conversion efficiency (PCE) of 17.5% with negligible hysteresis. An impressive current of 21 mA cm^?2 is also confirmed from photocurrent density with a higher fill factor of 0.79. The obtained PCE of 17.5% utilizing TPA‐ANT‐TPA is higher performance than the devices prepared using doped Spiro‐OMeTAD (16.8%) as hole transport layer at 1 sun condition. It is found that doping of LiTFSI salt increases hygroscopic characteristics in Spiro‐OMeTAD; this leads to the fast degradation of solar cells. While, solar cells prepared using undoped TPA‐ANT‐TPA show dewetting and improved stability. Additionally, the new HTMs form a fully homogeneous and completely covering thin film on the surface of the active light absorbing perovskite layers that acts as a protective coating for underlying perovskite films. This breakthrough paves the way for development of new inexpensive, more stable, and highly efficient ANT core based lower cost HTMs for cost‐effective, conventional, and printable PSCs.     

Dopant‐Free Hole Transporting Polymers for High Efficiency,Environmentally Stable Perovskite Solar Cells

Over the past five years, a rapid progress in organometal‐halide perovskite solar cells has greatly influenced emerging solar energy science and technology. In perovksite solar cells, the overlying hole transporting material (HTM) is critical for achieving high power conversion efficiencies (PCEs) and for protecting the air‐sensitive perovskite active layer. This study reports the synthesis and implementation of a new polymeric HTM series based on semiconducting 4,8‐dithien‐2‐yl‐benzo[1,2‐d;4,5‐d′]bistriazole‐alt‐benzo[1,2‐b:4,5‐b′]dithiophenes (pBBTa‐BDTs), yielding high PCEs and environmentally‐stable perovskite cells. These intrinsic (dopant‐free) HTMs achieve a stabilized PCE of 12.3% in simple planar heterojunction cells—the highest value to date for a polymeric intrinsic HTM. This high performance is attributed to efficient hole extraction/collection (the most efficient pBBTa‐BDT is highly ordered and orients π‐face‐down on the perovskite surface) and balanced electron/hole transport. The smooth, conformal polymer coatings suppress aerobic perovskite film degradation, significantly enhancing the solar cell 85 °C/65% RH PCE stability versus typical molecular HTMs.     

LiTFSI‐Free Spiro‐OMeTAD‐Based Perovskite Solar Cells with Power Conversion Efficiencies Exceeding 19%

To date, the most efficient perovskite solar cells (PSCs) employ an n–i–p device architecture that uses a 2,2′,7,7′‐tetrakis(N,N‐di‐p‐methoxyphenyl‐amine)‐9,9′‐spirobifluorene (spiro‐OMeTAD) hole‐transporting material (HTM), which achieves optimum conductivity with the addition of lithium bis(trifluoromethane)sulfonimide (LiTFSI) and air exposure. However, this additive along with its oxidation process leads to poor reproducibility and is detrimental to stability. Herein, a dicationic salt spiro‐OMeTAD(TFSI)₂, is employed as an effective p‐dopant to achieve power conversion efficiencies of 19.3% and 18.3% (apertures of 0.16 and 1.00 cm²) with excellent reproducibility in the absence of LiTFSI and air exposure. As far as it is known, these are the highest‐performing n–i–p PSCs without LiTFSI or air exposure. Comprehensive analysis demonstrates that precise control of the proportion of [spiro‐OMeTAD]⁺ directly provides high conductivity in HTM films with low series resistance, fast hole extraction, and lower interfacial charge recombination. Moreover, the spiro‐OMeTAD(TFSI)₂‐doped devices show improved stability, benefitting from well‐retained HTM morphology without forming aggregates or voids when tested under an ambient atmosphere. A facile approach is presented to fabricate highly efficient PSCs by replacing LiTFSI with spiro‐OMeTAD(TFSI)₂. Furthermore, this study provides an insight into the relationship between device performance and the HTM doping level.     

Incorporation of Counter Ions in Organic Molecules: New Strategy in Developing Dopant‐Free Hole Transport Materials for Efficient Mixed‐Ion Perovskite Solar Cells

Hole transport matertial (HTM) as charge selective layer in perovskite solar cells (PSCs) plays an important role in achieving high power conversion efficiency (PCE). It is known that the dopants and additives are necessary in the HTM in order to improve the hole conductivity of the HTM as well as to obtain high efficiency in PSCs, but the additives can potentially induce device instability and poor device reproducibility. In this work a new strategy to design dopant‐free HTMs has been presented by modifying the HTM to include charged moieties which are accompanied with counter ions. The device based on this ionic HTM X44 dos not need any additional doping and the device shows an impressive PCE of 16.2%. Detailed characterization suggests that the incorporated counter ions in X44 can significantly affect the hole conductivity and the homogeneity of the formed HTM thin film. The superior photovoltaic performance for X44 is attributed to both efficient hole transport and effective interfacial hole transfer in the solar cell device. This work provides important insights as regards the future design of new and efficient dopant free HTMs for photovotaics or other optoelectronic applications.     

High‐Performance and Stable Perovskite Solar Cells Based on Dopant‐Free Arylamine‐Substituted Copper(II) Phthalocyanine Hole‐Transporting Materials

A power conversion efficiency (PCE) as high as 19.7% is achieved using a novel, low‐cost, dopant‐free hole transport material (HTM) in mixed‐ion solution‐processed perovskite solar cells (PSCs). Following a rational molecular design strategy, arylamine‐substituted copper(II) phthalocyanine (CuPc) derivatives are selected as HTMs, reaching the highest PCE ever reported for PSCs employing dopant‐free HTMs. The intrinsic thermal and chemical properties of dopant‐free CuPcs result in PSCs with a long‐term stability outperforming that of the benchmark doped 2,2′,7,7′‐Tetrakis‐(N,N‐di‐p‐methoxyphenylamine)‐9,9′‐Spirobifluorene (Spiro‐OMeTAD)‐based devices. The combination of molecular modeling, synthesis, and full experimental characterization sheds light on the nanostructure and molecular aggregation of arylamine‐substituted CuPc compounds, providing a link between molecular structure and device properties. These results reveal the potential of engineering CuPc derivatives as dopant‐free HTMs to fabricate cost‐effective and highly efficient PSCs with long‐term stability, and pave the way to their commercial‐scale manufacturing. More generally, this case demonstrates how an integrated approach based on rational design and computational modeling can guide and anticipate the synthesis of new classes of materials to achieve specific functions in complex device structures.     

Less is More: Dopant‐Free Hole Transporting Materials for High‐Efficiency Perovskite Solar Cells

Perovskite solar cells have delivered power conversion efficiency beyond 22% in less than seven years, implying the potential for the paradigm shift of low‐cost photovoltaics with high efficiency and low embedded energy. Besides the “perovskite fever,” the development of new hole transport materials (HTM), especially dopant‐free HTMs, is another research hotspot. This is because the currently used HTMs, such as spiro‐OMeTAD derivatives, require additional chemical doping process to ensure sufficient conductivity and proper ionic potential level for efficient hole transport and collection. However, the commonly used dopants are volatile and hygroscopic which not only increase the complexity and cost of device fabrication but also deteriorate the device stability. So far, there have been several reviews on new HTMs, but review or analysis on dopant‐free HTMs is scarce. In this review, all reported dopant‐free HTMs are categorized into four primary different types and lessons will be learned during the separate discussions. The stability test behavior of all the intrinsic HTMs will be evaluated directly. In the end, the correlations between the properties of the intrinsic HTMs and parameters of the devices will be plotted to shed light on the future direction of development of this field.     

Rational Design of Dopant‐Free Coplanar D‐π‐D Hole‐Transporting Materials for High‐Performance Perovskite Solar Cells with Fill Factor Exceeding 80%

In this paper, two novel D‐π‐D hole‐transporting materials (HTM) are reported, abbreviated as BDT‐PTZ and BDT‐POZ , which consist of 4,8‐di(hexylthio)‐benzo[1,2‐b:4,5‐b′]dithiophene (BDT) as π‐conjugated linker, and N‐(6‐bromohexyl) phenothiazine (PTZ)/N‐(6‐bromohexyl) phenoxazine (POZ) as donor units. The above two HTMs are deployed in p‐i‐n perovskite solar cells (PSCs) as dopant‐free HT layers, exhibiting excellent power conversion efficiencies of 18.26% and 19.16%, respectively. Particularly, BDT‐POZ demonstrates a superior fill factor of 81.7%, which is consistent with its more efficient hole extraction and transport verified via steady‐state/transient fluorescence spectra and space‐charge‐limited current technique. Single‐crystal X‐ray diffraction characterization implies these two molecules present diverse packing tendencies, which may account for various interfacial hole‐transport ability in PSCs.     

Efficient CH3NH3PbI3 Perovskite Solar Cells Based on Graphdiyne (GD)‐Modified P3HT Hole‐Transporting Material

Novel large π‐conjugated carbon material, graphdiyne (GD), as a dopant to poly(3‐hexylthiophene) (P3HT) hole‐transporting material (HTM) layer, is introduced into perovskite solar cells for the first time. Raman spectroscopy and ultraviolet photoelectron spectroscopy measurements reveal that relatively strong π–π stacking interaction occurs between GD particles and P3HT (so‐called P3HT/GD composite HTM), favorable for the hole transportation and improvement of the cell performance. On the other hand, some GD aggregates exhibit a scattering nature, and thus help to increase the light absorption of the perovskite solar cells in the long wavelength range. As high as 14.58% light‐to‐electricity conversion efficiency is achieved, superior to the pristine P3HT‐based devices. Additionally, the devices exhibit good stability and reproducibility. Time‐resolved photoluminescence decay measurements reveal that the P3HT/GD HTM can accelerate the hole extraction compared with pristine P3HT.     

Copper Salts Doped Spiro‐OMeTAD for High‐Performance Perovskite Solar Cells

The development of effective and stable hole transporting materials (HTMs) is very important for achieving high‐performance planar perovskite solar cells (PSCs). Herein, copper salts (cuprous thiocyanate (CuSCN) or cuprous iodide (CuI)) doped 2,2,7,7‐tetrakis(N,N‐di‐p‐methoxyphenylamine)‐9,9‐spirobifluorene (spiro‐OMeTAD) based on a solution processing as the HTM in PSCs is demonstrated. The incorporation of CuSCN (or CuI) realizes a p‐type doping with efficient charge transfer complex, which results in improved film conductivity and hole mobility in spiro‐OMeTAD:CuSCN (or CuI) composite films. As a result, the PCE is largely improved from 14.82% to 18.02% due to obvious enhancements in the cell parameters of short‐circuit current density and fill factor. Besides the HTM role, the composite film can suppress the film aggregation and crystallization of spiro‐OMeTAD films with reduced pinholes and voids, which slows down the perovskite decomposition by avoiding the moisture infiltration to some extent. The finding in this work provides a simple method to improve the efficiency and stability of planar perovskite solar cells.     

High‐Efficiency CsPbI2Br Perovskite Solar Cells with Dopant‐Free Poly(3‐hexylthiophene) Hole Transporting Layers

CsPbI₂Br is emerging as a promising all‐inorganic material for perovskite solar cells (PSCs) due to its more stable lattice structure and moisture resistance compared to CsPbI₃, although its device performance is still much behind this counterpart. Herein, a preannealing process is developed and systematically investigated to achieve high‐quality CsPbI₂Br films by regulating the nucleation and crystallization of perovskite. The preannealing temperature and time are specifically optimized for a dopant‐free poly(3‐hexylthiophene) (P3HT)‐based device to target dopant‐induced drastic performance degradation for spiro‐OMeTAD‐based devices. The resulting P3HT‐based device exhibits comparable power conversion efficiency (PCE) to spiro‐OMeTAD‐based devices but much enhanced ambient stability with over 95% PCE after 1300 h. A diphenylamine derivative is introduced as a buffer layer to improve the energy‐level mismatch between CsPbI₂Br and P3HT. A record‐high PCE of 15.50% for dopant‐free P3HT‐based CsPbI₂Br PSCs is achieved by alleviating the open‐circuit voltage loss with the buffer layer. These results demonstrate that the preannealing processing together with a suitable buffer layer are applicable strategies for developing dopant‐free P3HT PSCs with high efficiency and stability.     

Solvent Engineering Boosts the Efficiency of Paintable Carbon‐Based Perovskite Solar Cells to Beyond 14%

Carbon‐based hole transport material (HTM)‐free perovskite solar cells (PSCs) have shown much promise for practical applications because of their high stability and low cost. However, the efficiencies of this kind of PSCs are still relatively low, especially for the simplest paintable carbon‐based PSCs, in comparison with the organic HTM‐based PSCs. This can be imputed to the perovskite deposition methods that are not very suitable for this kind of devices. A solvent engineering strategy based on two‐step sequential method is exploited to prepare a high‐quality perovskite layer for the paintable carbon‐based PSCs in which the solvent for CH₃NH₃I (MAI) solution at the second step is changed from isopropanol (IPA) to a mixed solvent of IPA/Cyclohexane (CYHEX). This mixed solvent not only accelerates the conversion of PbI₂ to CH₃NH₃PbI₃ but also suppresses the Ostwald ripening process resulting in a high‐quality perovskite layer, e.g., pure phase, even surface, and compact capping layer. The paintable carbon‐based PSCs fabricated from IPA/CYHEX solvent exhibits a considerable enhancement in photovoltaic performance and performance reproducibility in comparison with that from pure IPA, especially on fill factor (FF), owing mainly to the better contact of perovskite/carbon interface, lower trap density in perovskite, higher light absorption ability, and faster charge transport of perovskite layer. As a result, the highest power conversion efficiency (PCE) of 14.38% is obtained, which is a record value for carbon‐based HTM‐free PSCs. Furthermore, a PCE of as high as 10% is achieved for the large area device (1 cm²), also the highest of its kind.     

4‐Tert‐butylpyridine Free Organic Hole Transporting Materials for Stable and Efficient Planar Perovskite Solar Cells

4‐Tert ‐butylpyridine (t BP) is an important additive in triarylamine‐based organic hole‐transporting materials (HTMs) for improving the efficiency and steady‐state performance of perovskite solar cells (PVSCs). However, the low boiling point of t BP (196 °C) significantly affects the long‐term stability and device performance of PVSCs. Herein, the design and synthesis of a series of covalently linked Spiro[fluorene‐9,9′‐xanthene] (SFX)‐based organic HTMs and pyridine derivatives to realize efficient and stable planar PVSCs are reported. One of the tailored HTMs, N2,N2,N7,N7‐tetrakis(4‐methoxyphenyl)‐3′,6′‐bis(pyridin‐4‐ylmethoxy) spiro[fluorene‐9,9′‐xanthene]‐2,7‐diamine ( XPP ) with two para‐position substituted pyridines that immobilized on the SFX core unit shows a high power conversion efficiency (PCE) of 17.2% in planar CH₃NH₃PbI₃‐based PVSCs under 100 mW cm^?2 AM 1.5G solar illumination, which is much higher than the efficiency of 5.5% that using the well‐known 2,2′,7,7′‐tetrakis‐(N ,N ‐di‐p ‐methoxy‐phenyl‐amine)9,9′‐spirobifluorene (Spiro‐OMeTAD) as HTM (without t BP) under the same condition. Most importantly, the pyridine‐functionalized HTM‐based PVSCs without t BP as additive show much better long‐term stability than that of the state‐of‐the‐art HTM Spiro‐OMeTAD‐based solar cells that containing t BP as additive. This is the first case that the t BP‐free HTMs are demonstrated in PVSCs with high PCEs and good stability. It paves the way to develop highly efficient and stable t BP‐free HTMs for PVSCs toward commercial applications.     

Donor–Acceptor Type Dopant‐Free,Polymeric Hole Transport Material for Planar Perovskite Solar Cells (19.8%)

Organic–inorganic hybrid perovskite has led to the development of new solar cells with outstanding efficiency. In perovskite solar cells (PSCs), perovskite is sandwiched between a working electrode (fluorine‐doped tin oxide) and a counter electrode (gold, Au). In order to transport charges and block opposite charges, charge transport layers are inserted between perovskite and the electrodes. In particular, a hole transport layer is important because it generally prevents perovskite from exposure to air. Therefore, it is necessary to investigate dopant‐free and hydrophobic polymeric hole transport materials (HTMs). In this study, a novel polymeric HTM (PTEG) is synthesized by controlling the solubility using a tetraethylene glycol group. The planar‐PSC employing PTEG exhibits an efficiency of 19.8% without any dopants, which corresponds to the highest value reported to date. This study offers a fundamental strategy for designing and synthesizing various polymeric HTMs.     

Low‐Cost N,N′‐Bicarbazole‐Based Dopant‐Free Hole‐Transporting Materials for Large‐Area Perovskite Solar Cells

Despite the recent unprecedented development of efficient dopant‐free hole transporting materials (HTMs) for high‐performance perovskite solar cells (PSCs) on small‐area devices (≤0.1 cm²), low‐cost dopant‐free HTMs for large‐area PSCs (≥1 cm²) with high power conversion efficiencies (PCEs) have rarely been reported. Herein, two novel HTMs, 3,3′,6,6′ (or 2,2′,7,7′)‐tetrakis(N,N′‐di‐p‐methoxyphenylamine)‐N,N′‐bicarbazole (3,6 BCz‐OMeTAD or 2,7 BCz‐OMeTAD), are synthesized via an extremely simple route from very cheap raw materials. Owing to their excellent film‐forming abilities and matching energy levels, 3,6 BCz‐OMeTAD and 2,7 BCz‐OMeTAD can be successfully employed as a perfect ultrathin (≈30 nm) hole transporting layer in large‐area PSCs up to 1 cm². The 3,6 BCz‐OMeTAD and 2,7 BCz‐OMeTAD based large‐area PSCs show highest PCEs up to 17.0% and 17.6%, respectively. More importantly, high performance large‐area PSCs based on 2,7 BCz‐OMeTAD retain 90% of the initial efficiency after 2000 h storage in an ambient environment without encapsulation.     

Metal‐Oxide‐Free Methylammonium Lead Iodide Perovskite‐Based Solar Cells: the Influence of Organic Charge Transport Layers

Metal‐oxide‐free methylammonium lead iodide perovskite‐based solar cells are prepared using a dual‐source thermal evaporation method. This method leads to high quality reproducible films with large crystal domain sizes allowing for an in depth study of the effect of perovskite film thickness and the nature of the electron and hole blocking layers on the device performance. The power conversion efficiency increases from 4.7% for a device with only an organic electron blocking layer to almost 15% when an organic hole blocking layer is also employed. In addition to the in depth study on small area cells, larger area cells (approx. 1 cm^?2) are prepared and exhibit efficiencies in excess of 10%.     

Development of Dopant‐Free Organic Hole Transporting Materials for Perovskite Solar Cells

There has been considerable progress over the last decade in development of the perovskite solar cells (PSCs), with reported performances now surpassing 25.2% power conversion efficiency. Both long‐term stability and component costs of PSCs remain to be addressed by the research community, using hole transporting materials (HTMs) such as 2,2′,7,7′‐tetrakis(N,N′‐di‐pmethoxyphenylamino)‐9,9′‐spirbiuorene(Spiro‐OMeTAD) and poly[bis(4‐phenyl)(2,4,6‐trimethylphenyl)amine] (PTAA). HTMs are essential for high‐performance PSC devices. Although effective, these materials require a relatively high degree of doping with additives to improve charge mobility and interlayer/substrate compatibility, introducing doping‐induced stability issues with these HTMs, and further, additional costs and experimental complexity associated with using these doped materials. This article reviews dopant‐free organic HTMs for PSCs, outlining reports of structures with promising properties toward achieving low‐cost, effective, and scalable materials for devices with long‐term stability. It summarizes recent literature reports on non‐doped, alternative, and more stable HTMs used in PSCs as essential components for high‐efficiency cells, categorizing HTMs as reported for different PSC architectures in addition to use of dopant‐free small molecular and polymeric HTMs. Finally, an outlook and critical assessment of dopant‐free organic HTMs toward commercial application and insight into the development of stable PSC devices is provided.     

Nonaromatic Green‐Solvent‐Processable,Dopant‐Free,and Lead‐Capturable Hole Transport Polymers in Perovskite Solar Cells with High Efficiency

With the recent developments in the efficiency of perovskite solar cells (PSCs), diverse functionalities are necessary for next‐generation charge‐transport layers. Specifically, the hole‐transport layer (HTL) in the various synthesized materials modified with functional groups is explored. A novel donor–acceptor type polymer, alkoxy‐PTEG, composed of benzo[1,2‐b:4,5:b′]dithiophene and tetraethylene glycol (TEG)‐substituted 2,1,3‐benzothiadiazole is reported. The alkoxy‐PTEG exhibits high solubility even in nonaromatic solvents, such as 3‐methylcyclohexanone (3‐MC), and can prevent possible lead leakage via chelation. The optical and electronic properties of alkoxy‐PTEG are thoroughly analyzed. Finally, a dopant‐free alkoxy‐PTEG device processed with 3‐MC exhibits 19.9% efficiency and a device with 2‐methyl anisole, which is a reported aromatic food additive, exhibits 21.2% efficiency in a tin oxide planar structure. The PSC device shows 88% stability after 30 d at ambient conditions (40–50% relative humidity and room temperature). In addition, nuclear magnetic resonance reveals that TEG groups can chelate lead ions with moderate strength (K_binding = 2.76), and this strength is considered to be nondestructive to the perovskite lattice to prevent lead leakage. This is the first report to consider lead leakage and provide solutions to reduce this problem.     

Efficient Passivation with Lead Pyridine‐2‐Carboxylic for High‐Performance and Stable Perovskite Solar Cells

Stability has become the main obstacle for the commercialization of perovskite solar cells (PSCs) despite the impressive power conversion efficiency (PCE). Poor crystallization and ion migration of perovskite are the major origins of its degradation under working condition. Here, high‐performance PSCs incorporated with pyridine‐2‐carboxylic lead salt (PbPyA₂) are fabricated. The pyridine and carboxyl groups on PbPyA₂ can not only control crystallization but also passivate grain boundaries (GBs), which result in the high‐quality perovskite film with larger grains and fewer defects. In addition, the strong interaction among the hydrophobic PbPyA₂ molecules and perovskite GBs acts as barriers to ion migration and component volatilization when exposed to external stresses. Consequently, superior optoelectronic perovskite films with improved thermal and moisture stability are obtained. The resulting device shows a champion efficiency of 19.96% with negligible hysteresis. Furthermore, thermal (90 °C) and moisture (RH 40–60%) stability are improved threefold, maintaining 80% of initial efficiency after aging for 480 h. More importantly, the doped device exhibits extraordinary improvement of operational stability and remains 93% of initial efficiency under maximum power point (MPP) tracking for 540 h.     

Thermodynamically Self‐Healing 1D–3D Hybrid Perovskite Solar Cells

Thermal degradation in perovskite solar cells is still an unsettled issue that limits its further development. In this study, 2‐(1H‐pyrazol‐1‐yl)pyridine is introduced into lead halide 3D perovskites, which allows 1D–3D hybrid perovskite materials to be obtained. The heterostructural 1D–3D perovskites are proved to be capable of remarkably prolonging the photoluminescence decay lifetime and suppressing charge carrier recombination in comparison to conventional 3D perovskites. The intrinsic properties of thermodynamically stable yet kinetically labile 1D materials allow the system to alleviate the lattice mismatch and passivate the interface traps of heterojunction region of 1D–3D hybrid perovskites that may occur during the crystal growth process. Importantly, the as‐fabricated 1D–3D perovskite solar cells display a thermodynamic self‐healing ability, which is induced through blocking the ion‐migration channels of A‐site ions by the flexible 1D perovskite with less densely close‐packed structure. Particularly, the power conversion efficiency of as‐fabricated unencapsulated 1D–3D perovskite solar cells is demonstrated to be reversible under temperature cycling (25–85 °C) at 55% relative humidity, which largely outperforms the pure 3D perovskite solar cell. The present study provides a facile approach to fabricate 1D–3D perovskite solar cells with high efficiency and long‐term stability.     

Highly Efficient and Stable Perovskite Solar Cells Using a Dopant‐Free Inexpensive Small Molecule as the Hole‐Transporting Material

The hole transporting layer (HTL) plays an important role in realizing efficient and stable perovskite solar cells (PSCs). In spite of intensive research efforts toward the development of HTL materials, low‐cost, dopant‐free hole transporting materials that lead to efficient and stable PSCs remain elusive. Herein, a simple polycyclic heteroaromatic hydrocarbon‐based small molecule, 2,5,9,12‐tetra(tert‐butyl)diacenaphtho[1,2‐b:1′,2′‐d]thiophenen, as an efficient HTL material in PSCs is presented. This molecule is easy to synthesize and inexpensive. It is hydrophobic and exhibits excellent film‐forming properties on perovskites. It has unusually high hole mobility and a desirable highest occupied molecular orbital energy level, making it an ideal HTL material. PSCs fabricated using both the n‐i‐p planar and mesoscopic architectures with this compound as the HTL show efficiencies as high as 15.59% and 18.17%, respectively, with minimal hysteresis and high long term stability under ambient conditions.