Removal of hexavalent chromium in tannery wastewater by Bacillus cereus

Bacillus cereus was used to remove chromium (Cr(VI)) from medium containing tannery wastewater under different conditions. The maximum rate of Cr(VI) removal was attained at a temperature of 37?°C, pH of 7.0-9.0, and biomass of 20 g/L when the initial Cr(VI) concentration was less than 50?mg/L. Under the optimum conditions, the Cr(VI) in tannery wastewater was treated with each cellular component of B. cereus to detect its ability to reduce Cr(VI). The results showed that the removal rate of Cr(VI) for the cell-free extracts could reach 92.70%, which was close to that of the whole cells (96.85%), indicating that the Cr(VI) reductase generated by B.?cereus is primarily intracellular. Additionally, during continuous culture of the B. cereus, the strain showed good consecutive growth and removal ability. After treatment of 20?mg/L Cr(VI) for 48?h, the B. cereus was observed by SEM and TEM-EDX. SEM images showed that the B.?cereus used to treat Cr(VI) grew well and had a uniform cellular size. TEM-EDX analysis revealed large quantities of chromium in the B. cereus cells used to treat Cr(VI). Overall, the results presented herein demonstrate that B. cereus can be used as a new biomaterial to remove Cr(VI) from tannery wastewater.     

Efficacy of Acinetobacter sp. B9 for simultaneous removal of phenol and hexavalent chromium from co-contaminated system

The present study shows the feasibility of a newly isolated strain Acinetobacter sp. B9 for concurrent removal of phenol and Cr (VI) from wastewater. The experiments were conducted in a batch reactor under aerobic conditions. Initially, when mineral salt solution was used as the culture medium, the strain was found to utilize phenol as sole carbon and energy source while no Cr (VI) removal was observed. However, the addition of glucose as co-carbon source resulted in the removal of both toxicants. This co-removal efficiency of the strain was further improved with nutrient-rich media (NB). Optimum co-removal was determined at 188 mg L^?1 of phenol and 3.5 mg L^?1 of Cr (VI) concentrations at pH 7.0. Strain B9 followed the orthometabolic pathway for phenol degradation. Transmission electron microscopy (TEM) and Fourier transform infrared spectroscopy (FT-IR) studies showed sorption of chromium as one of the major mechanisms for Cr (VI) removal by B9 cells. Acinetobacter sp. B9 was later on checked for bioremediation of real tannery wastewater. After 96 h of batch treatment of tannery effluent containing an initial 47 mg L^?1 phenol and 16 mg L^?1 Cr (VI), complete removal of phenol and 87 % reduction of Cr (VI) were attained, showing high efficiency of the bacterial strain for potential application in industrial pollution control.     

Effect of toxic substances in anaerobic treatment of tannery wastewaters

Studies were carried out in the treatment of tannery wastewater using upflow anaerobic contact filter (reactor) and on the role of toxic substances viz tannin, sulphide, chromium (3+) in inhibiting the performance of the reactor. The influent COD concentration was varied in the range of 1500 to 16500?mg/l, at different hydraulic retention times viz 36,48,60 hr. The limiting concentrations of toxicity for the three substances viz tannin, sulphide, chromium (3+) were identified in terms of the performance of the reactor viz COD removal percent, biogas production etc. Toxic limits of the above mentioned substances were further estimated in batch process (in vials) to supplement the evidence. In anaerobic contact filter tannin beyond 914?mg/l inhibited the performance, whereas sulphide concentration even upto 180?mg/l and chromium (3+) concentration even upto 140?mg/l did not affect the reactor performance. In batch process tannin above 77 wt.% affected the anaerobic microbial growth. Hydrolysable tannin was present in these tannery wastewaters.     

Identification of Efficient Denitrifying Bacteria from Tannery Wastewaters in Ethiopia and a Study of the Effects of Chromium III and Sulphide on Their Denitrification Rate

In order to identify potential microorganisms with high denitrifying capacity from tannery wastewaters, 1000 pure cultures of bacterial isolates from Modjo Tannery Pilot and Ethio-tannery wastewater treatment plants (WWTP), in Ethiopia, were investigated. Twenty-eight isolates were selected as efficient denitrifiers. These were Gram-negative rods, oxidase and catalase positive denitrifying organisms. The 28 denitrifying strains were further classified according to their biochemical fingerprints into three different phylogenetic groups (BPT1, BPT2 and BPT3) and seven singles. Isolates B79^T, B11, B12, B15, B28 and B38 belonging to the BPT3 cluster were found to be the most efficient denitrifying bacteria. All phenotypic studies, including cellular fatty acid profiles, showed that the 6 BPT3 isolates were closely related to each other. The 16S rRNA partial sequence analysis of type strain B79^T(CCUG 45880) indicated a sequence similarity of 99% to Brachymonas denitrificans JCM9216 (D14320) in the β-subdivision of proteobacteria. Further studies of the effects of chromium III and sulphide on the six Brachymonas denitrificans strains indicated that denitrification by the isolates were inhibited 50% at concentrations of 54 and 96 mg/l, respectively. The efficient isolates characterized in this study are of great value because of their excellent denitrifying properties and relatively high tolerance to the concentrations of toxic compounds (70 mg chromium/l and 160 mg sulphide/l) prevailing in tannery wastewaters.     

Novel bioflocculant produced by salt-tolerant,alkaliphilic strain Oceanobacillus polygoni HG6 and its application in tannery wastewater treatment

The optimized production of MBF-HG6, which is a novel salt-tolerant alkaliphilic bioflocculant produced by Oceanobacillus polygoni with its application in tannery wastewater treatment was investigated in this study. It was found the optimal carbon source, nitrogen source, cation, and initial pH of the medium for bioflocculant production were starch, urea, Fe²⁺, and pH 9.0, respectively. The best stability in the temperature range was from 0 to 80°C and the purified MBF-HG6 contained polysaccharides of 81.53% and proteins of 9.98%. The carboxyl, hydroxyl, and amino groups were determined in bioflocculants, while the optimized bioflocculating activity was observed as 90.25% for the dosages of 6.96mL MBF-HG6, 4.77mL CaCl₂ (1%, m/v), and 19.24g/L NaCl using response surface methodology. In addition, SS and turbidity removal rates of the tannery wastewater (4g/L MBF-HG6) could, respectively, reach 46.49% and 91.08%, indicating that the great potential was emerged in enhancement of tannery wastewater treatment by MBF-HG6.     

Phycoremediation resultant lipid production and antioxidant changes in green microalgae Chlorella Sp.

In this investigation, we report on the treatment of tannery wastewater using microalgae Chlorella species to produce lipid and fatty acid as well as changes in antioxidant metabolism during the treatment. The variation in growth, production of pigments, antioxidant metabolism, lipid and fatty acids, and nutrient removal from wastewater during the remediation were observed. Surprisingly, a profuse growth was found in 50% diluted tannery wastewater (TW), which supported to accumulate high yield of lipid (18.5%) and unsaturated fatty acids (50.05%). The antioxidant activity of microalgae in both the concentrations (50% and 100% TW) were viz., lipid peroxidation 1.6 ± 0.1 and 2.3 ± 0.02nmol MDA mg^?1 protein, SOD 10.3 ± 0.4 and 15.7 ± 0.9 U mg^?1 protein, CAT 0.17 ± 0.036 and 0.52 ± 0.06 U mg^?1 protein, and APX 7.2 ± 0.8 and 11.2 ± 09 U mg^?1 protein respectively, which point out that the free radical scavenging mechanism against heavy metal stress. Maximum phycoremediation of heavy metals observed from both concentrations during the healthy growth period were Cr – 73.1, 45.7%, Cu – 90.4, 78.1%, Pb – 92.1, 52.2%, and Zn – 81.2, 44.6%, respectively. This study proved the potential use of Chlorella for heavy metal and nutrient removal from tannery wastewater. Moreover, an unaffected growth with high antioxidant activity of this species promises a sustainable lipid and fatty acid contents for biofuel production.     

The treatment of chromium tanning wastewater using natural marl

Abstract

The technical feasibility of removing chromium(III) from contaminated tannery wastewater by adsorption on naturally available marl, referred to as HEWAR in Palestine, has been investigated by batch experiments. The effects of various parameters on the percentage relative adsorption concentration were carried out by UV-vis spectrophotometry. Percentage relative concentration curves showed an increase with time until approaching a plateau (adsorption capacity). The adsorption capacity increased with the marl-to-liquid ratio, providing complete removal of chromium above 0.003g mL^?1 accomplished within 7 hours, while the marl particles were kept in suspension by stirring. The adsorption capacity increased with pH above 5.0, and decreased below this value. One sample of marl can be used for adsorbing chromium from various batches of wastewater until the adsorption sites are full.     

Lime enhanced chromium removal in advanced integrated wastewater pond system

The removal of trivalent chromium from a combined tannery effluent in horizontal settling tanks and subsequent Advanced Integrated Wastewater Pond System (AIWPS) reactors was investigated. The raw combined effluent from Modjo tannery had pH in the range of 11.2-12. At this pH, a trivalent chromium removal of 46-72% was obtained in the horizontal settling tanks after a one-day detention time. Trivalent chromium precipitated as chromium hydroxide, Cr(OH)3. 58-95% Cr(III) was removed in the advanced facultative pond (AFP) where the water column pH of 7.2-8.4 was close to pH 8, which is the optimum precipitation pH for trivalent chromium. Chromium removals in the secondary facultative pond (SFP) and maturation pond (MP) were 30-50% and 6-16%, respectively. With Cr(III) concentration of 0.2-0.8 mg/l in the final treated effluent, the AIWPS preceded by horizontal settling tanks produced effluent that could easily meet most of the current Cr(III) discharge limits to receive water bodies.     

Use of low-cost biological wastes and vermiculite for removal of chromium from tannery effluent

Biological wastes (sawdust, rice husk, coirpith and charcoal) and a naturally occurring mineral (vermiculite) have been tested for their effectiveness in removing Cr from tannery effluent through batch and column experiments. The adsorption capacities of the substrates were also evaluated using isotherm tests and computing distribution co-efficient. The sawdust exhibited a higher adsorption capacity (k = 1482 mgkg(-1)), followed by coirpith (k = 159 mgkg(-1)). The biosorbent and mineral vermiculite in columns were found very effective in removing Cr from tannery effluent. About 94% removal of Cr was achieved by a column of coirpith, and equally (93%) by a column containing a mixture of coirpith and vermiculite. This study showed that biological wastes are potential adsorbents of Cr, which could be successfully used to reduce the Cr concentrations in tannery effluent.     

Speciation and Environmental Fate of Chromium in Rivers Contaminated with Tannery Effluents

Redox and size speciation of chromium in rivers contaminated with tannery wastewater was carried out to provide insight into its transport and removal mechanisms. Total chromium was determined with Inductively Coupled Plasma‐Mass Spectrometry and Cr (VI) with Catalytic Adsorption Stripping Voltammetry. For the size speciation, particles were retained with a cartridge filter (cut‐off 1.2 μm) and the total filterable fraction was further fractionated with Tangential Flow Filtration to determine the concentrations of chromium associated with the High Molecular Weight Colloidal (HMWC), Low Molecular Weight Colloidal (LMWC) and Truly Dissolved (TD) fractions. Two fluvial systems of similar sizes, but located in contrasting climatic zones, were selected for comparison: the Sebou‐Fez system in Morocco and Dunajec River‐Czorsztyn Reservoir system in Poland. Particulate Cr dominated in the Sebou‐Fez system (about 90 %); while in the Dunajec‐Czorsztyn system, it represented only 17–53 % of the total chromium in raw water. Still, the partition coefficients [K_d] were of the same magnitude. Chromium (III) was the only form detected in Sebou‐Fez, whereas in Dunajec‐Czorsztyn Cr (VI) was also present with its proportion increasing downstream from the input of tannery wastewater due to the preferential removal of Cr (III). In the filtered water in Morocco a large fraction of Cr occurred in the HMWC fraction (50–70 %) at the two most contaminated sites, while the LMWC and TD forms prevailed at the non‐contaminated sites in the Sebou River. At a very high concentration, in the water in the proximity of tanneries (well above the theoretical saturation level) Cr precipitated as polynuclear Cr‐hydroxide. In Dunajec‐Czorsztyn, the partition of Cr (III) was approximately equal between the HMWC, LMWC and TD fractions, in contrast to Cr (VI) which occurred almost exclusively in the TD fraction. In both systems, Cr (III) was rapidly removed from the water to the sediments. The confluence of the Sebou with the Fez and the Czorsztyn reservoir trapped efficiently Cr (III) preventing its spreading over long distances. Cr (VI) showed conservative behavior and bypassed the Czorsztyn Reservoir. This study provides a first set of data on the partitioning of Cr (III) and Cr (VI) between the particulate, the colloidal and truly dissolved fractions in fluvial systems contaminated with tannery effluents. It also suggests that, in these systems, truly dissolved Cr (III) can be adequately modeled from the total filterable concentrations.     

Endophytic bacteria enhance remediation of tannery effluent in constructed wetlands vegetated with Leptochloa fusca

The use of constructed wetlands (CWs) is a promising approach for the remediation of wastewater. The present study aims to develop a plant–bacteria system within CWs for the efficient remediation of tannery effluent. In a vertical-flow CW vegetated with Leptochloa fusca (Kallar grass), a consortium of three different endophytic bacteria, Pantoea stewartii ASI11, Microbacterium arborescens HU33, and Enterobacter sp. HU38, was used for bioaugmentation. CWs vegetated with only L. fusca had the potential to remediate tannery effluent, but augmentation with endophytic bacteria enhanced the growth of L. fusca while aiding in the removal of both organic and inorganic pollutants from the tannery effluent. Moreover, the bacterial augmentation decreased toxicity in the effluent as well. A higher number of chromium (Cr)-resistant bacteria were isolated from the rhizosphere and endosphere of L. fusca inoculated with the endophytes than from uninoculated plants. Due to promising bioremediation and detoxification potential of L. fusca, it is reported for the first time as a potential candidate to develop effective CWs for the remediation of polluted effluents in combination with pollutant-degrading endophytic bacteria.     

Biodegradation of tannery wastewater using sequencing batch reactor--respirometric assessment

This investigation proved that respirometry combined with sequencing batch reactor (SBR) could be an effective way for the removal of COD in tannery wastewater. Measurement of oxygen uptake rates (OUR) and corresponding COD uptake rates showed that a 12-h operating cycle was optimum for tannery wastewater. The removal of COD by degradation was stoichiometric with oxygen usage. A plot of OUR values provided a good indication of the biological activity in the reactor. A high OUR value corresponded to the feed period; at the end of the cycle, when the substrate was depleted, the OUR value was low. At a 12-h SBR cycle with a loading rate of 1.9-2.1 kgm(-3) d(-1), removal of 80-82% COD, 78-80% TKN and 83-99% NH(3)-N were achieved. These removal efficiencies were much higher than the conventional aerobic systems. A simple method of COD fractionation was performed from the OUR and COD uptake rate data of the SBR cycle. About 66-70% of the influent COD was found to be readily biodegradable, 10-14% was slowly degradable and 17-21% was non-biodegradable. The oxygen mass transfer coefficient, K(L)a (19 +/- 1.7 h(-1)) was derived from respirometry. It was observed that with the exception of high organic load at the initial feed the oxygen transfer capacity was in excess of the OUR, and aerobic condition was generally maintained. Simultaneous nitrification-denitrification was observed in the SBR during the feed period as proved by mass balance.     

Chromium recycling of tannery waste through microbial fermentation

An Aspergillus carbonarius isolate, selected from an established microbial culture collection, was used to study the biodegradation of chromium shavings in solid-state fermentation experiments. Approximately 97% liquefaction of the tannery waste was achieved and the liquid obtained from long-term experiments was used to recover chromium. The resulting alkaline chromium sulfate solution was useful in tanning procedures. A proteinaceous liquid was also obtained which has potential applications as a fertilizer or animal feed additive and has several other industrial uses. The A. carbonarius strain proved to be a very useful tool in tannery waste-treatment processes and chromium recovery in the tanning industries.     

Toxicity of high salinity tannery wastewater and effects on constructed wetland plants

The toxicity of high salinity tannery wastewater produced after an activated sludge secondary treatment on the germination and seedling growth of Trifolium pratense, a species used as indicator in toxicity tests, was evaluated. Growth was inhibited by wastewater concentrations >25% and undiluted effluent caused a complete germination inhibition. Constructed wetlands (CWs) with Arundo donax or Sarcocornia fruticosa were envisaged to further polish this wastewater. Selection of plant species to use in CWs for industrial wastewater treatment is an important issue, since for a successful establishment they have to tolerate the often harsh wastewater composition. For that, the effects of this wastewater on the growth of Arundo and Sarcocornia were assessed in pot assays. Plants were subject to different wastewater contents (0/50/100%), and both were resilient to the imposed conditions. Arundo had higher growth rates and biomass than Sarcocornia and may therefore be the preferred species for use in CWs treating tannery wastewater. CWs planted with the above mentioned plants significantly decreased the toxicity of the wastewater, as effluent from the CWs outlet stimulated the growth of Trifolium at concentrations <50%, and seed germination and growth even occurred in undiluted effluent.     

Evaluation of different substrates to support the growth of Typha latifolia in constructed wetlands treating tannery wastewater over long-term operation

The aim of this study was to investigate the performance of horizontal subsurface flow constructed wetlands planted with Typha latifolia treating tannery wastewater under long-term operation. Two expanded clay aggregates (Filtralite MR3-8-FMR and Filtralite NR3-8-FNR) and a fine gravel-FG were used as substrate for the constructed wetland units plus one unit with FMR was left as an unvegetated control. The systems were subject to three hydraulic loadings, 18, 8 and 6cmd(-1), and to periods of interruption in the feed. The relationship between the substrate, plant development and removal efficiency, especially of organic matter, was investigated. Organic loadings up to 1800kg BOD(5)ha(-1)d(-1) and 3849kg COD ha(-1)d(-1) were applied leading to mass removals of up to 652kg BOD(5)ha(-1)d(-1) and 1869kg COD ha(-1)d(-1), respectively. The three different substrates were adequate for the establishment of T. latifolia, although the clay aggregates allowed for higher plant propagation levels. The units with FNR and FMR achieved significantly higher COD and BOD5 removal when compared to the FG and to the unplanted units. The systems proved to be tolerant to high organic loadings and to interruptions in feed suggesting this technology as a viable option for the biological treatment of tannery wastewater.     

Efficient bioremediation of tannery wastewater by monostrains and consortium of marine Chlorella sp. and Phormidium sp.

This study evaluated the bioremediation potential of two marine microalgae Chlorella sp. and Phormidium sp., both individually and in consortium, to reduce various pollutants in tannery wastewater (TW). The microalgae were grown in hazardous 100% TW for 20 days, and the reductions in biochemical oxygen demand (BOD), chemical oxygen demand (COD), total nitrogen (TN), total phosphorous (TP), chromium (Cr) and total dissolved solids (TDS) of the wastewater monitored periodically. Both marine isolates reduced the BOD and COD by ≥90% in the consortium and by over 80% individually. Concentrations of TN and TP were reduced by 91.16% and 88%, respectively, by the consortium. Removal/biosorption efficiencies for chromium ranged from 90.17–94.45%. Notably, the TDS, the most difficult to deal with, were reduced by >50% within 20 days by the consortium. The novel consortium developed in this study reduced most of the ecologically harmful components in the TW to within the permissible limits of discharge in about 5 to 15 days of treatment. Thus, both the tested marine strains of Chlorella and Phormidium sp. are promising for bioremediating/detoxifying TW and adequately improve the water quality for safe discharge into open water bodies, in particular when used as a consortium.     

Short-term batch studies on biological removal of chromium from synthetic wastewater using activated sludge biomass

Biological treatment of Cr(VI)-containing wastewater has drawn much attention recently as a method to treat environmental Cr(VI) contamination. The activated sludge method, due to its convenient operation and easy-to-scale-up, has been widely applied to treat municipal wastewater and some industrial wastewaters. In order to develop a suitable technique using activated sludge as the biomass to continuously remove Cr(VI) from wastewater, this paper investigated in short-term batch experiments the environmental elements affecting chromium biological removal from synthetic wastewater. The dissolved oxygen (DO), Cr(VI) initial concentration, biomass density, temperature, glucose content in the influent and contact time were observed to strongly influence chromium removal. It was found that the chromium removal efficiency decreased with the increase of DO and Cr(VI) initial concentration as well as glucose content in the feed, but increases in temperature and contact time improved the chromium removal efficiency. Although raising biomass concentration resulted in an increased chromium removal efficiency under both anaerobic and aerobic conditions, its influence on specific chromium removal was not significant.     

The microbial community in a moving bed biotrickling filter operated to remove hydrogen sulfide from gas streams

The information available on the microbial communities responsible for pollutant degradation is increasingly accessible. Its use to optimize process design and operation is an important challenge in the field of effluent treatment research. Therefore, a prototype of a moving bed biotrickling filter (MBBTF) reactor was designed and, for the first time, operated at full-scale for the removal of sulfides desorbing from tannery industrial wastewater. The bacterial community operating in this innovative reactor was studied, and its composition and response to different operating conditions were characterized. A stable biomass, dominated by sulfur-oxidizing bacteria of the genus Acidithiobacillus was selected from inside the MBBTF reactor, and temperature, pH and bed rotation were shown to be the main factors driving the community structure. Moreover, data from different approaches indicated an uneven spatial distribution of biofilm inside the studied reactor, due to the combined effect of fluid dynamics and substrate gradients within the bed volume. Despite the high removal efficiency achieved by this innovative prototype (80% on average), the data suggested that the result could be improved by adopting solutions for a more stable and even biofilm distribution. It was shown that short frequent bed rotations, rather than long scattered rotations, ensured biomass stability. Furthermore, diversifying biofilm support media as a function of expected local pollutant concentrations should be considered. Data obtained from the bacterial community can therefore provide indications for possible further improvement of MBBTF reactor design and performance.     

Campylobacter and Arcobacter species in food-producing animals: prevalence at primary production and during slaughter

The presence of very high concentrations of organic pollutants, phenols, tannins and heavy metals mainly chromium in wastewater discharged from leather industries, tags it as one of the most polluting industries. The phenolic syntans discharged from tanning units have an adverse effect on living organisms and cause serious environmental pollution, thereby making it very imperative to remove it. Among various treatment methods available for removal of phenols, biodegradation is environment friendly. The present study aims at the remediation of phenolic syntan used in the leather industry employing individual as well as co-culture of Bacillus cereus and Pseudomonas aeruginosa at varying syntan concentration in the medium. Parameters such as chemical oxygen demand (COD), total organic carbon (TOC), total phenol content (TPC) and Fourier Transform Infrared Spectroscopy (FTIR) indicating biodegradation were analyzed. Promising results were observed with P. aeruginosa, which exhibited a reduction in TPC by 62–72% in all the concentrations of syntan tested just within 12 h of inoculation, whereas about 67 and 83% reduction in COD and TOC respectively was observed for 2000 ppm concentration at the end of 5 days. B. cereus also demonstrated very good reduction in the above parameters however; percentage was less as compared to P. aeruginosa. In the case of co-culture, the TPC reduction was higher than B. cereus but lesser than P. aeruginosa. The percentage reduction in TOC and COD was highest for 500 ppm which eventually decreased for subsequent concentrations.

     

Ammonia-nitrogen and orthophosphate removal by immobilized Scenedesmus sp. isolated from municipal wastewater for potential use in tertiary treatment

Scendesmus sp. isolated from municipal wastewater, entrapped in calcium alginate as algal sheets was employed to remove inorganic nutrients (N and P) from artificial and real domestic secondary effluents in parallel-plate bioreactor after starvation. The key factors affecting the removal efficiency (NH4+-N and PO4(3-)-P), system stability and reuse efficiency of screens were studied and discussed. It has been shown that cell density in the mixture of algal gel was the key factor compared with the thickness of the gel and the cell density of the reactor. A complete removal of NH4+-N and PO4(3-)-P was achieved within 4h of treatment in parallel bioreactors with the optimal cell density in the mixture of algal (2 x 10(8) algae mL(-1)) and 3mm gel sheets after second cycle. Nine cycles of wastewater treatment in 21 days were accomplished, holding higher removal efficiency. NH(4)(+)-N removal efficiency was 99.1% after 105 min, 100% after 135 min, PO4(3-)-P removal efficiency was 100% after 15 min in domestic secondary effluents. Immobilized Scendesmus sp. is shown to have great potentialities for removal of inorganic nitrogen and phosphorus from treated effluents.