Mechanical properties of porcine femoral cortical bone measured by nanoindentation

This study uses a nanoindentation technique to examine variations in the local mechanical properties of porcine femoral cortical bone under hydrated conditions. Bone specimens from three age groups (6, 12 and 42 months), representing developing bone, ranging from young to mature animals, were tested on the longitudinal and transverse cross-sectional surfaces. Elastic modulus and hardness of individual lamellae within bone's microstructure: laminar bone, interstitial bone, and osteons, were measured. Both the elastic modulus and hardness increased with age. However, the magnitudes of these increases were different for each microstructural component. The longitudinal moduli were higher than the transverse moduli. Dehydrated samples were also tested to allow a comparison with hydrated samples and these resulted in higher moduli and hardness than the hydrated samples. Again, the degree of variation was different for each microstructural component. These results indicate that the developmental changes in bone have different rates of mechanical change within each microstructural component.     

Anisotropic viscoelastic properties of cortical bone

Relaxation Young's modulus of cortical bone was investigated for two different directions with respect to the longitudinal axis of bone (bone axis, BA): the modulus parallel (P) and normal (N) to the BA. The relaxation modulus was analyzed by fitting to the empirical equation previously proposed for cortical bones, i.e., a linear combination of two Kohlraush-Williams-Watts (KWW) functions (Iyo et al., 2003. Biorheology, submitted): E(t)=E0 (A1 exp[-(t/tau1)beta]+(1-A1) exp[-(t/tau2)gamma]), [0 < A1, beta, gamma < 1], where E0 is the initial modulus value E0. Tau1 and tau2(>tau1) are characteristic times of the relaxation, A1 is the fractional contribution of the fast relaxation (KWW1 process) to the whole relaxation process, and beta and gamma are parameters describing the shape of the relaxation modulus. In both P and N samples, the relaxation modulus was described well by the empirical equation. The KWW1 process of a P sample almost completely coincided with that of an N sample. In the slow process (KWW2 process), there was a difference between the relaxation modulus of a P sample and that of an N sample. The results indicate that the KWW1 process in the empirical equation represents the relaxation in the collagen matrix in bone and that the KWW2 process is related to a higher-order structure of bone that is responsible for the anisotropic mechanical properties of bone.     

Micromechanics modeling of Haversian cortical bone properties.

A finite-element micromechanics model for Haversian cortical bone tissue has been developed and studied. The model is an extension of two-dimensional micromechanics techniques for fiber-reinforced composite materials. Haversian systems, or secondary osteons, are considered to be the fiber component, and interstitial lamellar bone the matrix material. The cement line is included as an 'interphase' component along the fiber/matrix interface. The model assumes a regular repeatable spacing of the longitudinally aligned continuous fibers and is, therefore, restricted to approximating Haversian cortical bone in its present form. Haversian porosity is modeled explicitly by incorporating a hollow fiber to represent the Haversian canal. Solutions have been obtained by applying uniform macroscopic stresses to the boundaries of the repeating unit cell model. Macroscopic mechanical property predictions correspond reasonably well with the experimental data for cortical bone, but are necessarily dependent on the input properties for each constituent, which are not well established. The predicted variation in the elastic modulus with porosity is not as sensitive as that observed experimentally. Stresses within the constituents can also be modeled with this method and are demonstrated to deviate from the macroscopic applied stress levels.     

Some mechanical properties of goose femoral cortical bone

The ultimate compressive strength and modulus of elasticity of femoral cortical bone from adult geese (Anser anser), were determined by sex and by quadrant by compressing small right circular cylinders which were 2.4 mm in height and 0.8 mm in diameter. The average ultimate compressive strength was 183 +/- 29 MPa. The average modulus of elasticity was 13.2 +/- 3.4 GPa. The bending strength and bending modulus of elasticity were determined by a three point bend test on rectangular prisms which had the approximate dimensions 0.75 mm X 0.75 mm X 25 mm. The average bending strength was 263 +/- 44 MPa while the average bending modulus was 19.6 +/- 3.1 GPa. The calcium content was determined by atomic absorption spectrophotometry and no correlation was found with the mechanical properties. The histology of the cortical bone was examined both quantitatively and qualitatively. A unique type of Haversian bone is described. Goose bone was found to be morphologically similar to adolescent human bone and to have mechanical properties similar to those of adult human bone.     

Anisotropic properties of human cortical bone with osteogenesis imperfecta

The heterogeneity of bone shape and size variation is modulated by genetic, mechanical, nutritional, and hormonal patterning throughout its lifetime. Microstructural changes across cross sections are a result of mechanistic optimization that results over the years of evolution while being based on universal, time-invariant ingredients and patterns. Here we report changes across anatomical sections of bone with osteogenesis imperfecta (OI) that undermines the work of evolution through genetic mutation. This work examines the microstructure and molecular composition of different anatomical positions (anterior, medial, posterior, and lateral regions) in the diaphysis of an OI human tibia. The study shows that although there is no significant microstructural difference, molecular changes are observed using FTIR revealing differences in molecular composition of the four anatomical positions. In addition, the nanomechanical properties of anterior section of OI bone seem more heterogeneous. The nanomechanical properties of interstitial lamellae in all these bone samples are consistently greater than those of osteonal lamellae. The nanomechanical properties of bone depend on its anatomical section and on the measurement direction as well. Variations in molecular structure with anatomical positions and also corresponding differences in nanomechanical properties are reported. These are compared to those observed typically in healthy bone illustrating the unique influence of OI on bone multiscale behavior which results from an evolutionary process lasting for many years.     

Mechanical properties of a biodegradable bone regeneration scaffold

Poly (Propylene Fumarate) (PPF), a novel, bulk erosion, biodegradable polymer, has been shown to have osteoconductive effects in vivo when used as a bone regeneration scaffold (Peter, S. J., Suggs, L. J., Yaszemski, M. J., Engel, P. S., and Mikos, A. J., 1999, J. Biomater. Sci. Polym. Ed., 10, pp. 363-373). The material properties of the polymer allow it to be injected into irregularly shaped voids in vivo and provide mechanical stability as well as function as a bone regeneration scaffold. We fabricated a series of biomaterial composites, comprised of varying quantities of PPF, NaCl and beta-tricalcium phosphate (beta-TCP), into the shape of right circular cylinders and tested the mechanical properties in four-point bending and compression. The mean modulus of elasticity in compression (Ec) was 1204.2 MPa (SD 32.2) and the mean modulus of elasticity in bending (Eb) was 1274.7 MPa (SD 125.7). All of the moduli were on the order of magnitude of trabecular bone. Changing the level of NaCl from 20 to 40 percent, by mass, did not decrease Ec and Eb significantly, but did decrease bending and compressive strength significantly. Increasing the beta-TCP from 0.25 g/g PPF to 0.5 g/g PPF increased all of the measured mechanical properties of PPF/NVP composites. These results indicate that this biodegradable polymer composite is an attractive candidate for use as a replacement scaffold for trabecular bone.     

Dielectric properties of hydrated collagen

Dielectric measurements have been carried out on partially hydrated collagen in the frequency ranges 100 kHz–5 MHz, 100 MHz–1 GHz, and 8–23 GHz. In the low-frequency range, a dispersion was observed around 100 kHz which results from inhomogeneous conductivity of the samples. A dielectric relaxation was observed aroud 0.3 GHz using time-domain-spectroscopy techniques. This relaxation can be considered to originate from mobile side chains. Microwave measurements indicate that the water relaxation may extend into the 10-GHz region. An apparent discrepancy between the main water relaxation time and the average rotational correlation time of water as measured by nmr line widths was resolved by the assumption that a fraction of the water molecules is bound to the collagen with residence times on the order of 10^?6 sec, whereas the remainder of the water is only weakly bound and exhibits rotational rates on the order of 10^?10 sec.     

Mechanical properties of femoral trabecular bone in dogs

Background  

Studying mechanical properties of canine trabecular bone is important for a better understanding of fracture mechanics or bone disorders and is also needed for numerical simulation of canine femora. No detailed data about elastic moduli and degrees of anisotropy of canine femoral trabecular bone has been published so far, hence the purpose of this study was to measure the elastic modulus of trabecular bone in canine femoral heads by ultrasound testing and to assess whether assuming isotropy of the cancellous bone in femoral heads in dogs is a valid simplification.     

Mechanical properties of nacre and highly mineralized bone

We compared the mechanical properties of 'ordinary' bovine bone, the highly mineralized bone of the rostrum of the whale Mesoplodon densirostris, and mother of pearl (nacre) of the pearl oyster Pinctada margaritifera. The rostrum and the nacre are similar in having very little organic material. However, the rostral bone is much weaker and more brittle than nacre, which in these properties is close to ordinary bone. The ability of nacre to outperform rostral bone is the result of its extremely well-ordered microstructure, with organic material forming a nearly continuous jacket round all the tiny aragonite plates, a design well adapted to produce toughness. In contrast, in the rostrum the organic material, mainly collagen, is poorly organized and discontinuous, allowing the mineral to join up to form, in effect, a brittle stony material.     

Biomechanical properties enhancement of gamma radiation-sterilized cortical bone using antioxidants

Radiation and Environmental Biophysics - Gamma radiation sterilization is the method used by the majority of tissue banks to reduce disease transmission from infected donors to recipients through...     

Effect of mineral dissolution from bone specimens on the viscoelastic properties of cortical bone

Although physiological saline (0.15 M NaCl aqueous solution) has been used as a storage solution to prevent bone specimens from drying, there have been reports that Ca²⁺ ions dissolve from bone specimens during the storage in saline. In order to determine whether such storage has a marked effect on mechanical properties, the relaxation modulus of bovine cortical bone stored in physiological saline was compared with that stored in a buffer solution containing a sufficient amount of Ca²⁺ ions. After storage in saline, the modulus value of specimens was significantly reduced from that before storage. On the other hand, the modulus value of specimens soaked in the solution containing sufficient Ca²⁺ ions did not change after storage. The relaxation rate of a bone specimen stored in physiological saline was larger than that of a specimen stored in Ca²⁺-buffered saline solution and that of the control specimens. The results suggest that by the dissolution of Ca²⁺ ions from a bone specimen during storage in physiological saline, percolated paths of mineral phase and of reinforced matrix phase are disjoined, resulting in reduction in the elastic modulus and change in the viscoelastic properties of bone.     

Mechanical loading: biphasic osteocyte survival and targeting of osteoclasts for bone destruction in rat cortical bone

Bone isremoved or replaced in defined locations by targeting osteoclasts andosteoblasts in response to its local history of mechanical loading.There is increasing evidence that osteocytes modulate this targeting bytheir apoptosis, which is associated with locally increasedbone resorption. To investigate the role of osteocytes in the controlof loading-related modeling or remodeling, we studied the effects onosteocyte viability of short periods of mechanical loading applied tothe ulnae of rats. Loading, which produced peak compressive strains of0.003 or 0.004, was associated with a 78% reduction in theresorption surface at the midshaft. The same loading regimen resultedin a 40% relative reduction in osteocyte apoptosis at the samesite 3 days after loading compared with the contralateral side(P = 0.01). The proportion of osteocytes that wereapoptotic was inversely related to the estimated local strain(P < 0.02). In contrast, a single short period ofloading resulting in strains of 0.008 engendered both tissuemicrodamage and subsequent bone remodeling and was associated with aneightfold increase in the proportion of apoptotic osteocytes(P = 0.02) at 7 days. This increase in osteocyteapoptosis was transient and preceded both intracorticalremodeling and death of half of the osteocytes (P < 0.01). The data suggest that osteocytes might use their U-shapedsurvival response to strain as a mechanism to influence boneremodeling. We hypothesize that this relationship reflects a causalmechanism by which osteocyte apoptosis regulates bone'sstructural architecture.

     

Mechanical properties of metaphyseal bone in the proximal femur

We used a three-point bending test to investigate the structural behavior of 123 rectangular flat plate specimens harvested from the metaphyseal shell of the cervical and intertrochanteric regions of five fresh/frozen human proximal femora. For comparison purposes, 36 specimens of similar geometry were also fabricated from bone of the femoral diaphysis. All specimens were oriented in either the local longitudinal or transverse directions. The mean longitudinal elastic modulus was 9650 +/- 2410 (SD) MPa and demonstrated a 24% decrease from that measured for the diaphysis (12500 +/- 2140 MPa) using the same testing technique. However, the transverse elastic moduli did not differ significantly between the proximal (5470 +/- 1720 MPa) and diaphyseal (5990 +/- 1520 MPa) specimens. The globally averaged values for the ultimate tensile strengths of the metaphyseal shell were 101 +/- 26 MPa in the longitudinal and 50 +/- 12 MPa in the transverse directions. These compared with diaphyseal values of 128 +/- 16 MPa and 47 +/- 12 MPa, respectively. While these differences were largely due to the reduced density of the proximal specimens, a slight decrease in transverse anisotropy for the proximal specimens was also noted by comparing the ratio of longitudinal to transverse moduli (1.76) and tensile strength (2.02) to the diaphyseal values (2.09 and 2.71, respectively). Use of these data should lead to improved performance of analytical models for the proximal femur, and thus help focus increased attention on the structural contribution of trabecular bone to the strength and rigidity of the proximal femur.