Saccharomyces cerevisiae fermentations in a pilot scale airlift bioreactor: Comparison of air sparger configurations

Hydrodynamic and oxygen transfer comparisons were made between two ring sparger locations, draft tube and annulus, in a concentric pilot scale airlift reactor with a baker's yeast suspension. Sectional hydrodynamic measurements were made and a mobile DOT probe was used to characterise the oxygen transfer performance through the individual sections of the reactor. The hydrodynamic performance of the reactor was improved by using a draft tube ring sparger rather than the annulus ring sparger. This was due to the influence of the ratio of the cross sectional area of the downcomer and riser (A _D/A_R) in conjunction with the effect of liquid velocity and a parameter,C ₀, describing the distribution of the liquid velocity and gas holdup across the riser on the bubble coalescence rates. The mixing performance of the reactor was dominated by the frequency of the passage of the broth through the end sections of the reactor. An optimum liquid height above the draft tube, for liquid mixing was demonstrated, above which no further improvement in mixing occurred. The liquid velocity and degree of gas entrainment showed little dependency on top section size for both sparger configurations. Extreme dissolved oxygen heterogeneity was demonstrated around the vessel with both sparger configurations and was shown to be detrimental to the oxygen uptake rate of the baker's yeast. Dissolved oxygen tensions below 1% air saturation occurred along the length of the riser and then rose in the downcomer. The greater oxygen transfer rate in the downcomer than in the riser was caused by the combined effects of a larger slip velocity in the downcomer which enhancedk _La and gas residence time, high downcomer gas holdup, and the change in bubble size distribution between the riser and downcomer. The position of greatest oxygen transfer rate in the downcomer was shown to be affected by the reactor from the influence on downcomer liquid linear velocity. UCL is the Biotechnology and Biological Sciences Research Council sponsored Advanced Centre for Biochemical Engineering and the Council's support is greatly acknowledged.     

Reactor heterogeneity with saccharopolyspora erythraea airlift fermentations

Bioreactor heterogeneity has been studied in a multiconfigurable pilot-scale airlift reactor (0.25 m3) which created different degrees of heterogeneity. The impact of the two sparger configurations, i.e. in the draft tube or the annulus, in conjunction with a marine propeller fitted at the base of the downcomer, on the physiology of Saccharopolyspora erythraea was studied. Cellular growth, morphology, and productivity were compared between airlift and stirred tank reactors. Dissolved oxygen tension heterogeneity caused by differences in dissolved oxygen tension around the vessel did not affect growth, but the reduction of heterogeneity improved the specific erythromycin production rate and final specific production. Erythromycin production was shown to be proportional to the energy dissipation rate. The enhancement of bubble coalescence with increasing apparent viscosity led to the reduction of the sectional gas holdups and the improvement of liquid mixing. The extent of the changes with increasing apparent viscosity was dependent on the broth morphology, reactor configurations, and operating conditions. Copyright 1998 John Wiley & Sons, Inc.     

Scale up of a viscous fungal fermentation: application of scale-up criteria with regime analysis and operating boundary conditions

The scale up of the novel, pharmaceutically important pneumocandin (B(0)), from the filamentous fungus Glarea lozoyensis was successfully completed from pilot scale (0.07, 0.8, and 19 m(3)) to production scale (57 m(3)). This was accomplished, despite dissimilar reactor geometry, employing a combination of scale-up criteria, process sensitivity studies, and regime analysis using characteristic time constants for both oxygen mass transfer and bulk mixing. Dissolved oxygen tension, separated from the influence of agitation by gas blending at the 0.07 m(3)-scale, had a marked influence on the concentrations of pneumocandin analogs with different levels of hydroxylation, and these concentrations were used as an indicator of bulk mixing upon scale up. The profound impact of dissolved oxygen tension (DOT) (low and high levels) on analog formation dictated the use of constant DOT, at 80% air saturation, as a scale-up criterion. As a result k(L)a, Oxygen uptake rate (OUR) and hence the OTR were held constant, which were effectively conserved across the scales, while the use of other criterion such as P(g)/V(L), or mixing time were less effective. Production scale (57 m(3)) mixing times were found to be faster than those at 19 m(3) due to a difference in liquid height/tank diameter ratio (H(L)/D(T)). Regime analysis at 19 and 57 m(3) for bulk mixing (t(c)) and oxygen transfer (1/k(L)a) showed that oxygen transfer was the rate-limiting step for this highly shear thinning fermentation, providing additional support for the choice of scale-up criterion.     

Hexadecane mineralization in oxygen-controlled sediment-seawater cultivations with autochthonous microorganisms.

Laboratory studies investigated the influence of dissolved oxygen tension (DOT) on microbial degradation of hexadecane in cultures with sediment-seawater suspensions. With a fermentor system, it was possible to adjust and regulate different oxic conditions (DOTs between 0.4 and 80% of oxygen saturation) as well as anoxia. The effects of DOT reduction on the amount and rate of hexadecane degraded and on the degree of mineralization and on the production of biomass were investigated. When the DOT was reduced from 80% to 5%, no dependence of the investigated parameters on the oxygen concentration was found. The amount of hexadecane degraded was constant, with an average value of 86% of the initially applied amount. The degradation rate was constant even down to 1% DOT, with an average value of 0.15 mg of hexadecane per g of sediment per h (16.2 mg liter-1 h-1). The mean degree of mineralization was 70% of the initially applied hexadecane, and biomass production reached a value of about 1.5 g per g of hexadecane consumed. A significant influence on the degradation process was detected only with DOTs below 1%. The degree of mineralization and the amount of degraded hexadecane decreased, whereas the degradation rate was still unaffected. Under anoxic conditions, no hexadecane degradation occurred within 190 h. The fact that the hexadecane biodegradation rate was constant down to at least 0.04% DOT shows that the actual oxygen concentration is of minor importance as long as the oxygen supply is high enough to guarantee the oxygen-dependent degradation step.     

Hexadecane mineralization in oxygen-controlled sediment-seawater cultivations with autochthonous microorganisms.

Laboratory studies investigated the influence of dissolved oxygen tension (DOT) on microbial degradation of hexadecane in cultures with sediment-seawater suspensions. With a fermentor system, it was possible to adjust and regulate different oxic conditions (DOTs between 0.4 and 80% of oxygen saturation) as well as anoxia. The effects of DOT reduction on the amount and rate of hexadecane degraded and on the degree of mineralization and on the production of biomass were investigated. When the DOT was reduced from 80% to 5%, no dependence of the investigated parameters on the oxygen concentration was found. The amount of hexadecane degraded was constant, with an average value of 86% of the initially applied amount. The degradation rate was constant even down to 1% DOT, with an average value of 0.15 mg of hexadecane per g of sediment per h (16.2 mg liter-1 h-1). The mean degree of mineralization was 70% of the initially applied hexadecane, and biomass production reached a value of about 1.5 g per g of hexadecane consumed. A significant influence on the degradation process was detected only with DOTs below 1%. The degree of mineralization and the amount of degraded hexadecane decreased, whereas the degradation rate was still unaffected. Under anoxic conditions, no hexadecane degradation occurred within 190 h. The fact that the hexadecane biodegradation rate was constant down to at least 0.04% DOT shows that the actual oxygen concentration is of minor importance as long as the oxygen supply is high enough to guarantee the oxygen-dependent degradation step.     

Anaerobic treatment of baker's yeast wastewater: I. Start-up and sodium molybdate addition

The anaerobic treatment of baker's yeast wastewater was studied using an anaerobic biological contact reactor (AnRBC) and a fixed-film reactor. The AnRBC had an active biomass developed within the reactor before this study commenced; however, the fixed-film reactor was started without attached biomass in a support structure. The gas production rates obtained for the AnRBC were between 0·55 and 0·61 litre methane per litre reactor per day. However, a gas production rate of only 0·46 litre methane per litre reactor per day was achieved after a four-month operating period for the fixed-film reactor. Higher chemical oxygen demand reduction was also found in the AnRBC. The results indicated that the presence of high sulfate concentration in baker's yeast wastewater affected teh start-up process. The reactor with fully developed active biomass was less susceptible to sulfate inhibition and showed improved anaerobic digestion. Results indicate that the reactor should be innoculated by feeding nutrient-balanced substrate before it was subjected to the digestion of baker's yeast wastewater. The fixed-film reactor was also fed with the substrate contianing sodium molybdate, an inhibitor of sulfate-reducing bacteria. The results indicated that both methanogenic and sulfate-reducing bacteria were inhibited.     

Effect of cycling dissolved oxygen concentrations on product formation in penicillin fermentations

Summary Limitations in mass and momentum transfer coupled with high hydrostatic pressures create significant spatial variations in dissolved gas concentrations in large fermenters. Microorganisms are subjected to fluctuating environmental conditions as they pass through the zones in a stirred vessel or along a closed loop fermenter.A 7-litre fermenter was modified to simulate the dissolved gas and hydrostatic pressure gradients in large vessels.The effect of cycling dissolved oxygen tension (DOT) on penicillin production by Penicillium chrysogenum P1 was investigated. The fermentation was affected by evironmental conditions such as medium composition, pH, size of inoculum, stirrer speed and DOT. Inoculum size below 10% (v/v) and stirrer speeds above 850 rpm caused significant reductions in specific prenicillin production rates (q_pen). q_pen values were measured at different constant DOT levels. Below 30% air saturation q_pen decreased sharply and no production was observed at 10%. Penicillin synthesis was impaired irreversibly below 10% DOT. The same profile was observed at higher stirrer speeds and air flow rates indicating that the effect was a physiological one. Oxygen uptake of the culture was affected significantly below 7% DOT, demonstrating that the critical DOT values for penicillin production and oxygen uptake are two distinct parameters. Carrying out the fermentation at one atmosphere over pressure was found to have no effect. When the dissolved oxygen concentration of the culture medium was cycled around the critical DOT for penicillin production, a considerable decrease in the specific penicillin production rate was observed. The effect was reversible but not transient, indicating a shift in cell metabolism.These results demonstrate the unfavourable effect of fluctuating environmental conditions on culture performance in stirred tanks. They suggest that these effects should be accounted for during strain selection, process development and scale up stages of an industrial process if the productivities in small scale vessels are to be obtained.     

Determination of external and internal mass transfer limitation in nitrifying microbial aggregates

In this article we present a study of the effects of external and internal mass transfer limitation of oxygen in a nitrifying system. The oxygen uptake rates (OUR) were measured on both a macro-scale with a respirometric reactor using off-gas analysis (Titrimetric and Off-Gas Analysis (TOGA) sensor) and on a micro-scale with microsensors. These two methods provide independent, accurate measurements of the reaction rates and concentration profiles around and in the granules. The TOGA sensor and microsensor measurements showed a significant external mass transfer effect at low dissolved oxygen (DO) concentrations in the bulk liquid while it was insignificant at higher DO concentrations. The oxygen distribution with anaerobic or anoxic conditions in the center clearly shows major mass transfer limitation in the aggregate interior. The large drop in DO concentration of 22-80% between the bulk liquid and aggregate surface demonstrates that the external mass transfer resistance is also highly important. The maximum OUR even for floccular biomass was only attained at much higher DO concentrations (approximately 8 mg/L) than typically used in such systems. For granules, the DO required for maximal activity was estimated to be >20 mg/L, clearly indicating the effects of the major external and internal mass transfer limitations on the overall biomass activity. Smaller aggregates had a larger volumetric OUR indicating that the granules may have a lower activity in the interior part of the aggregate.     

Oxygen transfer measurements during yeast fermentations in a pilot scale airlift fermenter

Measurements of oxygen transfer were made during cultivation of the yeast Saccharomyces cerevisiae in a 90–250 litre working volume concentric tube airlift fermenter. Results demonstrated that the rate of oxygen transfer varies with position in the fermenter, being higher in the riser and top-section than in the downcomer and lowest near the base of the fermenter. The time for liquid circulation was generally smaller than the time constant for oxygen transfer (1/k_La) indicating that the rate of oxygen transfer was slow compared to the rate of liquid movement. Measured dissolved oxygen concentrations therefore did not represent the equilibrium arising from the balance between the rates of oxygen transfer and oxygen depletion. Hence measuredk _L a values were not representative of local oxygen transfer conditions but instead were indicators of the rate of mass transfer the liquid flow had encountered prior to reaching the point of measurement. Generally the individual rates of oxygen transfer in the vessel were found to increase with increasing vessel height.     

The effect of dissolved oxygen tension and the utility of oxygen uptake rate in insect cell culture

Dissolved oxygen tension and oxygen uptake rate are critical parameters in animal cell culture. However, only scarce information of such variables is available for insect cell culture. In this work, the effect of dissolved oxygen tension (DOT) and the utility of on-line oxygen uptake rate (OUR) measurements in monitoring Spodoptera frugiperda (Sf9) cultures were determined. Sf9 cells were grown at constant dissolved oxygen tensions in the range of 0 to 30%. Sf9 metabolism was affected only at DOT below 10%, as no significant differences on specific growth rate, cell concentration, amino acid consumption/production nor carbohydrates consumption rates were found at DOT between 10 and 30%. The specific growth rate and specific oxygen uptake rate followed typical Monod kinetics with respect to DOT. The calculated _max and max were 0.033 h^-1 and 3.82×10^-10 mole cell^-1h^-1, respectively, and the corresponding saturation constants were 1.91 and 1.57%, respectively. In all aerated cultures, lactate was consumed only after glucose and fructose had been exhausted. The yield of lactate increased with decreasing DOT. It is proposed, that an apparent DOT in non-instrumented cultures can be inferred from the lactate yield of bioreactors as a function of DOT. Such a concept, can be a useful and important tool for determining the average dissolved oxygen tension in non-instrumented cultures. It was shown that the dynamic behavior of OUR can be correlated with monosaccharide (fructose and glucose) depletion and viable cell concentration. Accordingly, OUR can have two important applications in insect cell culture: for on-line estimation of viable cells, and as a possible feed-back control variable in automatic strategies of nutrient addition.Abbreviations DOT Dissolved oxygen tension - OUR Oxygen uptake rate - specific oxygen uptake rate - specific growth rate - X_v viable cell concentration - C_L, C^*, and oxygen concentrations in liquid phase, in equilibrium with gas phase, and medium molar concentration, respectively - H Henry's constant - K_La volumetric oxygen transfer coefficient - P_T total pressure - oxygen partial pressure - oxygen molar fraction - i discrete element     

Hairy root culture in a liquid-dispersed bioreactor: characterization of spatial heterogeneity

A liquid-dispersed reactor equipped with a vertical mesh cylinder for inoculum support was developed for culture of Atropa belladonna hairy roots. The working volume of the culture vessel was 4.4 L with an aspect ratio of 1.7. Medium was dispersed as a spray onto the top of the root bed, and the roots grew radially outward from the central mesh cylinder to the vessel wall. Significant benefits in terms of liquid drainage and reduced interstitial liquid holdup were obtained using a vertical rather than horizontal support structure for the biomass and by operating the reactor with cocurrent air and liquid flow. With root growth, a pattern of spatial heterogeneity developed in the vessel. Higher local biomass densities, lower volumes of interstitial liquid, lower sugar concentrations, and higher root atropine contents were found in the upper sections of the root bed compared with the lower sections, suggesting a greater level of metabolic activity toward the top of the reactor. Although gas-liquid oxygen transfer to the spray droplets was very rapid, there was evidence of significant oxygen limitations in the reactor. Substantial volumes of non-free-draining interstitial liquid accumulated in the root bed. Roots near the bottom of the vessel trapped up to 3-4 times their own weight in liquid, thus eliminating the advantages of improved contact with the gas phase offered by liquid-dispersed culture systems. Local nutrient and product concentrations in the non-free-draining liquid were significantly different from those in the bulk medium, indicating poor liquid mixing within the root bed. Oxygen enrichment of the gas phase improved neither growth nor atropine production, highlighting the greater importance of liquid-solid compared with gas-liquid oxygen transfer resistance. The absence of mechanical or pneumatic agitation and the tendency of the root bed to accumulate liquid and impede drainage were identified as the major limitations to reactor performance. Improved reactor operating strategies and selection or development of root lines offering minimal resistance to liquid flow and low liquid retention characteristics are possible solutions to these problems.     

The scale-up of plant cell culture: Engineering considerations

The enormous versatility of plants has continued to provide the impetus for the development of plant tissue culture as a commercial production strategy for secondary metabolites. Unfortunately problems with slow growth rates and low products yields, which are generally non-growth associated and intracellular, have made plant cell culture-based processes, with a few exceptions, economically unrealistic. Recent developments in reactor design and control, elicitor technology, molecular biology, and consumer demand for natural products, are fuelling a renaissance in plant cell culture as a production strategy. In this review we address the engineering consequences of the unique characteristics of plant cells on the scale-up of plant cell culture.Abbreviations a gas-liquid interfacial area per volume - C dissolved oxygen concentration - C^* liquid phase oxygen concentration in equilibrium with the partial pressure of oxygen in the bulk gas phase - K_L overall mass transfer coefficient - k_L liquid film mass transfer coefficient - m_O2 cell maintenance coefficient for oxygen - OTR oxygen transfer rate - OUR oxygen uptake rate - pO₂ partial pressure of oxygen - STR stirred-tank reactor - v.v.m. volume of gas fed per unit operating volume of reactor per minute - X biomass concentration - Y_x/O2 biomass yield coefficient for oxygen - specific growth rate     

Potential errors in conventional DOT measurement techniques in shake flasks and verification using a rotating flexitube optical sensor

Background  

Dissolved oxygen tension (DOT) is an important parameter for evaluating a bioprocess. Conventional means to measure DOT in shake flasks using fixed Clark-type electrodes immersed in the bulk liquid are problematic, because they inherently alter the hydrodynamics of the systems. Other approaches to measure DOT that apply fluorescing sensor spots fixed at the inside wall of a shake flask are also suboptimal. At low filling volumes for cultivating microorganisms with a high oxygen demand, the measured DOT signal may be erroneous. Here, the sensor spot is sometimes exposed to gas in the head space of the flask. Merely repositioning the sensor spot elsewhere in the flask does not address this problem, since there is no location in the shake flask that is always covered by the rotating bulk liquid. Thus, the aim of this prospective study is first, to verify the systemic error of Clark-type electrodes for measuring DOT in shake flasks. The second principle aim is to use the newly built "flexitube optical sensor" to verify potential errors in conventional optical DOT measurements based on fixed sensor spots.     

Biodegradation of tannery wastewater using sequencing batch reactor--respirometric assessment

This investigation proved that respirometry combined with sequencing batch reactor (SBR) could be an effective way for the removal of COD in tannery wastewater. Measurement of oxygen uptake rates (OUR) and corresponding COD uptake rates showed that a 12-h operating cycle was optimum for tannery wastewater. The removal of COD by degradation was stoichiometric with oxygen usage. A plot of OUR values provided a good indication of the biological activity in the reactor. A high OUR value corresponded to the feed period; at the end of the cycle, when the substrate was depleted, the OUR value was low. At a 12-h SBR cycle with a loading rate of 1.9-2.1 kgm(-3) d(-1), removal of 80-82% COD, 78-80% TKN and 83-99% NH(3)-N were achieved. These removal efficiencies were much higher than the conventional aerobic systems. A simple method of COD fractionation was performed from the OUR and COD uptake rate data of the SBR cycle. About 66-70% of the influent COD was found to be readily biodegradable, 10-14% was slowly degradable and 17-21% was non-biodegradable. The oxygen mass transfer coefficient, K(L)a (19 +/- 1.7 h(-1)) was derived from respirometry. It was observed that with the exception of high organic load at the initial feed the oxygen transfer capacity was in excess of the OUR, and aerobic condition was generally maintained. Simultaneous nitrification-denitrification was observed in the SBR during the feed period as proved by mass balance.     

Oxygen transfer in a multiple air-lift loop reactor

The Multiple Air-lift Loop reactor (MAL) is a new type of bioreactor, in which a series of airlifts with internal loops is incorporated into one vessel. As such, the MAL is an approximation of an aerated plug-flow fermenter. Gas/liquid oxygen transfer was studied as a function of the gas flow rate in a MAL. The second MAL-compartment in the series was investigated in particular, and a Rectangular Air-lift Loop reactor (RAL) was used as a reference. Both a dynamic and a steady-state method were used for the determination of the overall volumetric oxygen-transfer coefficient. Both methods gave the same results. The oxygen transfer coefficient in the second MAL-compartment was low compared to that of conventional internal-loop reactors. Wall effects probably caused bubble coalescence and a reduction in the oxygen transfer. For the RAL it was found that oxygen transfer was comparable to that in a bubble column.     

Evaluation of the effects and interactions of mixing and oxygen transfer on the production of Fab’ antibody fragments in Escherichia coli fermentation with gas blending

Fermentations carried out at 450-L and 20-L scale to produce Fab’ antibody fragments indicated a serious problem to control levels of dissolved oxygen in the broth due to the large oxygen demand at high cell densities. Dissolved oxygen tension (DOT) dropped to zero during the induction phase and it was hypothesised that this could limit product formation due to inadequate oxygen supply. A gas blending system at 20-L scale was employed to address this problem and a factorial 2² experimental design was executed to evaluate independently the effects and interaction of two main engineering factors: agitation rate and DOT level (both related to mixing and oxygen transfer in the broth) on Fab’ yields. By comparison to the non-gas blending system, results in the gas blending system at same scale showed an increase in the production of Fab’ by 77% independent of the DOT level when using an agitation rate of 500 rpm level and by 50% at an agitation rate of 1,000 rpm with 30% DOT. Product localisation in the cell periplasm of >90% was obtained in all fermentations. Results obtained encourage further studies at 450-L scale initially, to evaluate the potential of gas blending for the industrial production of Fab’ antibody fragments.     

Kinetics of nitrification using a fluidized sand bed reactor with attached growth

The oxidation of ammonium ion to nitrite and nitrate ion (nitrification) has been studied in a laboratory scale fluidized sand bed reactor with attached microbial growth. The undefined population of Nitrobacteracea organisms were immobilized on the sand particles by natural attachment after 2–3 months of adaptation. General balance equations have been formulated for a recycle reactor and oxygenation tank system. Kinetic experiments in the reactor and in a microrespirometer have been analyzed in terms of double Michaelis–Menten rate expression for the nitrogenous reactants and dissolved oxygen. Dynamic simulation of the batch integral reactor system was used to establish the error in the kinetic constant which arose due to assuming differential behavior. Design guidelines have been developed for the oxygen requirements in terms of oxygen transfer coefficients, oxygen enrichment, and liquid recycle rate.     

Oxygen supply controls the onset of pristinamycins production by Streptomyces pristinaespiralis in shaking flasks

Antibiotics are secondary metabolites, generally produced during stationary phase of growth under different nutritional and hydrodynamic stresses. However, the exact mechanisms of the induction of antibiotics production are still not clearly established. In a previous study, the induction of pristinamycins production by Streptomyces pristinaespiralis as well as product concentrations were correlated with power dissipation per unit of volume (P/V) in shaking flasks. In this study, detailed kinetics of growth, substrate consumption, oxygen transfer rate and pristinamycins production under varying P/V conditions have been obtained and analyzed. Our results showed that higher P/V resulted in a higher concentration of biomass and promoted an earlier nutrient limitation and ultimately an earlier induction of pristinamycins production. The maximal specific growth rate, specific oxygen consumption rate and specific consumption rate of glutamate increased with P/V while influence was less marked with specific consumption rate of glucose, arginine, ammonium ions and phosphate. When oxygen uptake rate (OUR) was limited by free-surface oxygen transfer, pristinamycins production was not detected despite the occurrence of nitrogen and/or phosphate sources limitation. The threshold value for OUR observed was around 25 mmol L(-1) h(-1). This suggested that a limitation in nitrogen and/or phosphate alone was not sufficient to induce pristinamycins production by S. pristinaespiralis pr11. To induce this production, the oxygen transfer had to be non-limiting.     

Enhanced mixing and mass transfer in a recirculation loop results in high cell densities in a roller bottle reactor

A recirculation loop added to a large-scale roller bottle reactor resulted in high cell densities as compared to standard roller bottles. Four different mammalian cell lines reached an average maximum density equal to 5.4 x 10(6) cells /mL (sigma = 0.263), which was between 2.13 and 2.95 times greater than the densities in roller bottles without recirculation using the same cell lines. The high densities were maintained over long durations (>25 days) while the reactor operated with continuous perfusion. The increased densities are attributed to enhanced liquid mixing and oxygen transfer that occur as a result of the recirculation loop. Models were developed that describe axial liquid flow and oxygen transfer in both the sample loop and the reactor growth chamber. Axial dispersion and oxygen transfer coefficients are presented for a variety of operating conditions. The increased oxygen transfer characteristics of the reactor allow for easy scale-up of roller bottle cultures by operating at larger volumes with greater liquid depths than conventional roller bottles permit. The surface-area-to-volume ratio in the tests performed was 0.206 versus 1.16 cm(-1) in a standard roller bottle.