Biodiesel production via transesterification of palm olein using waste mud crab (Scylla serrata) shell as a heterogeneous catalyst

A recent rise in crab aquaculture activities has intensified the generation of waste shells. In the present study, the waste shells were utilized as a source of calcium oxide to transesterify palm olein into methyl esters (biodiesel). Characterization results revealed that the main component of the shell is calcium carbonate which transformed into calcium oxide when activated above 700 °C for 2 h. Parametric studies have been investigated and optimal conditions were found to be methanol/oil mass ratio, 0.5:1; catalyst amount, 5 wt.%; reaction temperature, 65 °C; and a stirring rate of 500 rpm. The waste catalyst performs equally well as laboratory CaO, thus creating another low-cost catalyst source for producing biodiesel. Reusability results confirmed that the prepared catalyst is able to be reemployed up to 11 times. Statistical analysis has been performed using a Central Composite Design to evaluate the contribution and performance of the parameters on biodiesel purity.     

Production of biodiesel from acid waste lard

The objective of the present work was: (i) to enable biodiesel production from acid waste lard; (ii) to study the esterification reaction as possible pre-treatment at different temperatures, catalyst amount and reaction times; (iii) to evaluate biodiesel quality according to EN 14214 after basic transesterification of the pre-treated fat; and (iv) to predict the impact of using such waste as raw material in mixture with soybean oil. Temperature and catalyst amount were the most important reaction conditions which mostly affected biodiesel quality, namely viscosity and purity. The selected pre-treatment conditions were 65 °C, 2.0 wt% H₂SO₄ and 5 h, which allowed obtaining a product with a viscosity of 4.81 mm² s⁻¹ and a purity of 99.6 wt%. The proposed pre-treatment was effective to enable acid wastes as single raw materials for biodiesel production with acceptable quality; however, low yields were obtained (65 wt%). Alkali transesterification of a mixture of waste lard and soybean oil resulted in a product with a purity of 99.8 wt% and a yield of 77.8 wt%, showing that blending might be an interesting alternative to recycle such wastes. Also, because in addition to using conventional and relatively economical processes, some biodiesel properties depending on the raw material composition (such as the iodine value) might even be improved.     

Biodiesel production and optimization from Calophyllum inophyllum linn oil (honne oil) – A three stage method

The present work examines the production of a biodiesel from a non-edible oil namely honne oil (Calophyllum inophyllum linn). A three stage process viz., pre-treatment, alkali catalyzed transesterification and post treatment adopted for the production is discussed. The reaction parameters such as methanol to oil molar ratio, catalyst concentration, temperature and time have been optimized for the production of biodiesel. The yield of biodiesel from the honne oil under the optimized conditions is found to be 89%.     

Biodiesel production from high acid value waste frying oil catalyzed by superacid heteropolyacid

Transesterification of waste cooking oil with high acid value and high water contents using heteropolyacid H3PW12O40 x 6H2O (PW12) as catalyst was investigated. The hexahydrate form of PW(12) was found to be the most promising catalyst which exhibited highest ester yield 87% for transesterification of waste cooking oil and ester yield 97% for esterification of long-chain palmitic acid, respectively. The PW12 acid catalyst shows higher activity under the optimized reaction conditions compared with conventional homogeneous catalyst sulfuric acid, and can easily be separated from the products by distillation of the excess methanol and can be reused more times. The most important feature of this catalyst is that the catalytic activity is not affected by the content of free fatty acids (FFAs) and the content of water in the waste cooking oil and the transesterification can occur at a lower temperature (65 degrees C), a lower methanol oil ratio (70:1) and be finished within a shorter time. The results illustrate that PW12 acid is an excellent water-tolerant and environmentally benign acid catalyst for production of biodiesel from waste cooking oil.     

Direct preparation of biodiesel from rapeseed oil leached by two-phase solvent extraction

A new method which coupled the two-phase solvent extraction (TSE) with the synthesis of biodiesel was studied. Investigations were carried out on transesterification of methanol with oil-hexane solution coming from TSE process in the presence of sodium hydroxide as the catalyst. Biodiesel (fatty acid methyl esters) were the products of transesterification. The influential factors of transesterification, such as reaction time, catalyst concentration, mole ratio of methanol to oil and reaction temperature were optimized. The results showed that the optimal reaction parameters were sodium hydroxide concentration 1.1% by weight of rapeseed oil, mole ratio of methanol to oil 9:1, reaction time 120 min, and reaction temperature 55-60 degrees C. Under these conditions, the TG conversion would rise up to 98.2%. Based on the new method, biodiesel production process could be simplified and the biodiesel cost could be reduced.     

Optimisation of integrated biodiesel production. Part I. A study of the biodiesel purity and yield

This study consists of the development and optimisation of the potassium hydroxide-catalysed synthesis of fatty acid methyl esters (biodiesel) from sunflower oil. A factorial design of experiments and a central composite design have been used. The variables chosen were temperature, initial catalyst concentration by weight of sunflower oil and the methanol:vegetable oil molar ratio, while the responses were biodiesel purity and yield. The initial catalyst concentration is the most important factor, having a positive influence on biodiesel purity, but a negative one on biodiesel yield. Temperature has a significant positive effect on biodiesel purity and a significant negative influence on biodiesel yield. The methanol:vegetable oil molar ratio is only significant for the biodiesel purity, having a positive influence. Second-order models were obtained to predict biodiesel purity and yield as a function of these variables. The best conditions are 25 degrees C, a 1.3%wt for the catalyst concentration and a 6:1 methanol:sunflower oil molar ratio.     

Use of experimental design to investigate biodiesel production by multiple-stage Ultra-Shear reactor

This work presents biodiesel production from soybean oil and bioethanol by multiple-stage Ultra-Shear reactor (USR). The experiments were carried out in the following conditions: reaction time from 6 to 12 min; catalyst concentration from 0.5% to 1.5% by weight of soybean oil; ethanol: soybean oil molar ratio from 6:1 to 10:1. The experimental design was used to investigate the influence of process variables on the conversion in biodiesel. The best ethyl ester conversion obtained was 99.26 wt.%, with ethanol:soybean oil molar ratio of 6:1, catalyst concentration of 1.35% and with 12 min of reaction time.     

Optimization Studies and Chemical Kinetics of Silica Sulfuric Acid-Catalyzed Biodiesel Synthesis from Waste Cooking Oil

In the present study conversion of waste cooking oil to biodiesel has been carried out via simultaneous esterification and transesterification reaction over silica sulfuric acid as a solid acid catalyst. The process variables that influence the fatty acid methyl ester (FAME) conversion, such as reaction temperature, reaction time, catalyst concentration and methanol to oil molar ratio were investigated and optimized using Taguchi method. Highest FAME production obtained under the optimized condition was 98.66 %. Analysis of variance revealed that temperature was the most significant factor effecting the FAME production among four factors studied. From the kinetic study, the reaction was found to follow pseudo first-order kinetics and rate constant of the reaction under optimum condition was 0.00852 min^?1.     

Biodiesel production by enzymatic process using Jatropha oil and waste soybean oil

In this study, non-edible Jatropha oil and postcooking waste soybean oil were utilized for enzymatic biodiesel production. The process was optimized by using a statistical method. In addition, a novel continuous process using co-immobilized Rhizopus oryzae and Candida rugosa lipases was developed. The optimum conditions for the batch process were determined to be a reaction temperature of 45oC, an agitation speed of 250 rpm, 10 wt% of water, and 20% of immobilized lipases. A conversion of about 98% at 4 h could be achieved for biodiesel production using Jatropha oil, while a conversion of about 97% at 4 h was achieved from waste soybean oil. A packed bed reactor charged with co-immobilized lipases was employed for continuous biodiesel production from Jatropha and waste soybean oil. The reactor consisted of a jacketed glass column (ID 25 mm × 130 mm), in which a temperature of 45°C was maintained by water circulation. A maximum conversion of about 80% in 24 h at a flow rate of 0.8 mL/ min was achieved with the continuous process, whereas in the two-stage continuous process, a conversion of about 90% in 72 h was attained at a flow rate of 0.1 mL/min.     

Enzyme catalyzed transesterification of waste cooking oil with dimethyl carbonate

The detrimental effects of waste cooking oil on sewer system attracted attention toward its proper management and reusing this waste oil for making biodiesel provides commercial and environmental advantage. In the present study, biodiesel has been successfully produced from waste cooking oil and dimethyl carbonate by transesterification, instead of the conventional alcohol. In this optimization study, the effect of various reaction conditions such as solvent, time and temperature, molar ratio of DMC to oil, enzyme loading and reusability, on the yield of fatty acid methyl ester (FAME) has been studied. The Maximum conversion of FAMEs achieved was 77.87% under optimum conditions (solvent free system, reaction time of 24 h, 60 °C, molar ratio of DMC to oil 6:1, catalyst amount 10% Novozym 435 (based on the oil weight)). Moreover, there was no obvious loss in the conversion after lipases were reused for 6 batches under optimized conditions.     

Biodiesel production using a membrane reactor

The immiscibility of canola oil in methanol provides a mass-transfer challenge in the early stages of the transesterification of canola oil in the production of fatty acid methyl esters (FAME or biodiesel). To overcome or rather, exploit this situation, a two-phase membrane reactor was developed to produce FAME from canola oil and methanol. The transesterification of canola oil was performed via both acid- or base-catalysis. Runs were performed in the membrane reactor in semi-batch mode at 60, 65 and 70 degrees C and at different catalyst concentrations and feed flow rates. Increases in temperature, catalyst concentration and feedstock (methanol/oil) flow rate significantly increased the conversion of oil to biodiesel. The novel reactor enabled the separation of reaction products (FAME/glycerol in methanol) from the original canola oil feed. The two-phase membrane reactor was particularly useful in removing unreacted canola oil from the FAME product yielding high purity biodiesel and shifting the reaction equilibrium to the product side.     

Enzymatic coproduction of biodiesel and glycerol carbonate from soybean oil and dimethyl carbonate

The enzymatic coproduction of biodiesel and glycerol carbonate by the transesterification of soybean oil was studied using lipase as catalyst in organic solvent. To produce biodiesel and glycerol carbonate simultaneously, experiments were designed sequentially. Enzyme screening, the molar ratio of dimethyl carbonate (DMC) to soybean oil, reaction temperature and solvent effects were investigated. The results of enzyme screening, at 100 g/L Novozym 435 (immobilized Candida antarctica lipase B), biodiesel and glycerol carbonate showed conversions of 58.7% and 50.7%, respectively. The optimal conditions were 60 °C, 100 g/L Novozym 435, 6.0:1 molar ratio with tert-butanol as solvent: 84.9% biodiesel and 92.0% glycerol carbonate production was achieved.     

Effects of environmental conditions and methanol feeding strategy on lipase-mediated biodiesel production using soybean oil

Methanol is a commonly used acyl acceptor for lipase-driven biodiesel production, but a high concentration of methanol is detrimental for lipase activity. To overcome this drawback, a simple fed-batch process was developed by optimization of the methanol feeding strategy and reaction conditions. For the feeding strategy, an equal volume of pure methanol was fed twice with specified time intervals into a reactor initially containing a 1:1 molar ratio of soybean oil to methanol in order to adjust the net molar ratio of the oil to methanol to 1:3. In contrast with the batch reaction, a higher agitation speed in the fed-batch process elevated the conversion yield of soybean oil to biodiesel. An agitation speed of 600 rpm and a reaction temperature of 70°C were chosen as the optimal environmental conditions. Residual lipase activities for the fed-batch operation at 40 ∼ 70°C and 600 rpm were 7.1 ± 1.4 times higher than that of the batch method at 40°C with the same agitation speed, indicating that methanol feeding can prevent significant deactivation of lipase. Finally, two times feeding methanol at 2 and 6 hr resulted in a biodiesel productivity of 10.7%/h and 94.9% final conversion yield under the optimal conditions.     

Sonication-assisted production of biodiesel using soybean oil and supercritical methanol

High temperature and pressure are generally required to produce biodiesel using supercritical methanol. We reduced the harsh reaction conditions by means of sonicating the reaction mixture prior to transesterification using supercritical methanol. Soybean oil was selected as the raw material for transesterification. As soybean oil contains more unsaturated fatty acid triglycerides, the biodiesel degraded more at high temperature. The reactants were sonicated for 60 min at 35 °C prior to transesterification to avoid degradation of the product and to enhance biodiesel yield at temperatures <300 °C. The process parameters were optimized using central composite design. The variables selected for optimization were temperature, time, and the oil to methanol molar ratio. The temperature and oil to methanol molar ratios were varied from 250 to 280 °C and 1:40–1:50, respectively. The reaction time was tested between 4 and 12 min. The biodiesel was analyzed for any possible degradation by gas chromatography–mass spectroscopy and for the wt% of fatty acid methyl esters (FAME) obtained. The maximum FAME yield (84.2 wt%) was obtained at a temperature of 265.7 °C, an oil to alcohol molar ratio of 1:44.7, and a time of 8.8 min. The optimum yield was obtained at a pressure of 1,500 psi. The pressure and optimum temperature used to obtain the maximum yield were the lowest reported so far without the use of a co-solvent. Thus, the severity of the supercritical reactions was reduced by adding sonication prior to the reaction.     

Ultrasonic monitoring of glycerol settling during transesterification of soybean oil

A low-intensity ultrasonic measurement system was used to monitor the products of transesterification of soybean oil in methanol to FAME (biodiesel). The byproducts of the transesterification reaction are methyl esters, glycerol and other products. During the transesterification reaction, the glycerol, having a higher density than the methyl ester, settles at the bottom of the reaction vessel. The aim of this study was to measure the glycerol deposition rate during transesterification and to assess the reaction rate and end time. Soybean oil was converted into biodiesel at four temperature levels. The amount of catalyst (KOH) used in the transesterification reactions was determined by titration. The ultrasonic waveforms captured during the reaction were recorded and analyzed automatically. The ultrasonic system monitored the effects of reaction temperatures on the glycerol settling rate and the reaction end times. The ultrasonic measurement of glycerol settling would be a useful non-destructive method for evaluating the effects of parameters such as catalyst amount, mixing time and temperature on transesterification reactions.     

Ethanesulfonic acid-based esterification of industrial acidic crude palm oil for biodiesel production

An industrial grade acidic crude palm oil (ACPO) pre-treatment process was carried out using ethanesulfonic acid (ESA) as a catalyst in the esterification reaction. ESA was used in different dosages to reduce free fatty acid (FFA) to a minimum level for the second stage of biodiesel production via alkaline transesterification reaction. Different process operating conditions were optimized such as ESA dosage (0.25-3.5% wt/wt), methanol to ACPO molar ratio (1:1-20:1), reaction temperature (40-70 °C), and reaction time (3-150 min). This study revealed the potential use of abundant quantities of ACPO from oil palm mills for biodiesel production. The lab scale results showed the effectiveness of the pre-treatment process using ESA catalyst. Three consecutive catalyst recycling runs were achieved without significant degradation in its performance. Second and third reuse runs needed more reaction time to achieve the target level of FFA content. Esterification and transesterification using ESA and KOH respectively is proposed for biodiesel industrial scale production. The produced biodiesel meets the international standards specifications for biodiesel fuel (EN 14214 and ASTM D6751).     

Application of calcined waste fish (Labeo rohita) scale as low-cost heterogeneous catalyst for biodiesel synthesis

This paper explores the feasibility of converting waste Rohu fish (Labeo rohita) scale into a high-performance, reusable, low-cost heterogeneous catalyst for synthesis of biodiesel from soybean oil. The thermo-gravimetric analysis (TGA) and X-ray diffraction (XRD) analysis revealed that a significant portion of the main component of fish scale i.e. HAP (hydroxyapatite) could be transformed into β-tri-calcium phosphate when calcined above 900°C for 2 h. Scanning Electron Microscopy (SEM) morphology studies of the calcined scale depicted a fibrous layer of porous structure; while a BET surface area of 39 m(2)/g was measured. Response surface methodology (RSM) was employed to determine the optimal parametric conditions viz. methanol/oil molar ratio, 6.27:1, calcination temperature, 997.42°C and catalyst concentration, 1.01 wt.% of oil corresponding to a maximum FAME yield of 97.73%. Reusability results confirmed that the prepared catalyst could be reemployed up to six times, procreating a potentially applicable avenue in biodiesel synthesis.     

Statistical analysis and optimization of biodiesel production from waste coffee grounds by a two-step process

Biodiesel was produced using waste coffee grounds (WCGs) via a two-step process comprising lipid extraction and subsequent transesterification steps. Each step was statistically analyzed, and optimum conditions for each step were suggested. WCGs were found to have 16.4% lipid content with 1.9% free fatty acid (FFA) content. The liquid-solid ratio (LSR) significantly influenced lipid extraction from WCGs, while extraction time and temperature did not; 92.7% of lipid extraction efficiency was achieved at 13.7 mL-hexane/g-WCGs, 30 min of extraction time, and 25°C. Owing to the relatively low FFA content, an alkaline catalyst (NaOH) reaction was used that requires less amount of catalyst, methanol, and shorter reaction time compared to an acid catalyst reaction. Reaction time and temperature were the major factors affecting biodiesel conversion, and 94.0% of biodiesel conversion was obtained at optimum conditions for transesterification: 0.5% catalyst, 1.5 mL-methanol/g-lipid, 45°C, and 9 h of reaction time. With the use of statistical analysis tools, high lipid extraction efficiency and biodiesel conversion were achieved at relatively mild conditions, which would reduce biodiesel production cost substantially.     

Microwave assisted alkali-catalyzed transesterification of Pongamia pinnata seed oil for biodiesel production

In this study, microwave assisted transesterification of Pongamia pinnata seed oil was carried out for the production of biodiesel. The experiments were carried out using methanol and two alkali catalysts i.e., sodium hydroxide (NaOH) and potassium hydroxide (KOH). The experiments were carried out at 6:1 alcohol/oil molar ratio and 60 °C reaction temperature. The effect of catalyst concentration and reaction time on the yield and quality of biodiesel was studied. The result of the study suggested that 0.5% sodium hydroxide and 1.0% potassium hydroxide catalyst concentration were optimum for biodiesel production from P. pinnata oil under microwave heating. There was a significant reduction in reaction time for microwave induced transesterification as compared to conventional heating.     

K_2CO_3/γ-Al_2O_3催化棕榈油和甲醇酯交换反应制备生物柴油

采用浸渍法制备K2CO3/γ-Al2O3负载型固体碱催化剂,用X线衍射(XRD)和热质量分析法(DSC-TGA)表征催化剂的物化性质,考察催化剂在棕榈油和甲醇酯交换制备生物柴油中的反应性能。结果表明:活性组分已成功负载到载体γ-Al2O3上,且在高温焙烧过程中K2CO3和γ-Al2O3之间产生了相互作用;在K2CO3负载量22.6%、醇油摩尔比12∶1、反应时间3h、催化剂质量分数3%、反应温度65℃的条件下,甲酯产率最高可达91.6%。