Amperometric sensors based on Ni/Al and Co/Al layered double hydroxides modified electrode and their application for hydrogen peroxide detection

Two different hydrogen peroxide sensors were constructed with Ni/Al and Co/Al layered double hydroxides (LDHs) modified glassy carbon electrodes (GCE). Ni (Co)/Al-LDHs were synthesized by electrochemical method and were characterized by scanning electron microscopy (SEM) and energy dispersive spectrometry (EDS). The advantages and shortcoming of the two hydrogen peroxide sensors were described in detail. Compared to Co/Al-LDHs modified electrode, sensors fabricated by Ni/Al-LDHs showed quicker heterogeneous electron transfer rate constants (k(s)), lower detection and better reproducibility. But Co/Al-LDHs modified electrode held the advantages of wider linear range and higher sensitivity. Further more, the different catalytic redox mechanisms of hydrogen peroxide on the Ni/Al/GCE and Co/Al/GCE were firstly comparatively explored.     

Direct electrochemistry and electrocatalytic activity of catalase immobilized onto electrodeposited nano-scale islands of nickel oxide

Cyclic voltammetry was used for simultaneous formation and immobilization of nickel oxide nano-scale islands and catalase on glassy carbon electrode. Electrodeposited nickel oxide may be a promising material for enzyme immobilization owing to its high biocompatibility and large surface. The catalase films assembled on nickel oxide exhibited a pair of well defined, stable and nearly reversible CV peaks at about -0.05 V vs. SCE at pH 7, characteristic of the heme Fe (III)/Fe (II) redox couple. The formal potential of catalase in nickel oxide film were linearly varied in the range 1-12 with slope of 58.426 mV/pH, indicating that the electron transfer is accompanied by single proton transportation. The electron transfer between catalase and electrode surface, (k(s)) of 3.7(+/-0.1) s(-1) was greatly facilitated in the microenvironment of nickel oxide film. The electrocatalytic reduction of hydrogen peroxide at glassy carbon electrode modified with nickel oxide nano-scale islands and catalase enzyme has been studied. The embedded catalase in NiO nanoparticles showed excellent electrocatalytic activity toward hydrogen peroxide reduction. Also the modified rotating disk electrode shows good analytical performance for amperometric determination of hydrogen peroxide. The resultant catalase/nickel oxide modified glassy carbon electrodes exhibited fast amperometric response (within 2 s) to hydrogen peroxide reduction (with a linear range from 1 microM to 1 mM), excellent stability, long term life and good reproducibility. The apparent Michaelis-Menten constant is calculated to be 0.96(+/-0.05)mM, which shows a large catalytic activity of catalase in the nickel oxide film toward hydrogen peroxide. The excellent electrochemical reversibility of redox couple, high stability, technical simplicity, lake of need for mediators and short preparations times are advantages of this electrode. Finally the activity of biosensor for nitrite reduction was also investigated.     

Nickel (II) Complexes of Histidyl-Peptides as Fenton-Reaction Catalysts

Addition of histidyl-peptides containing the glycyl-glycyl-L-histidyl sequence stimulated the catalysis of Ni(II) hydrogen peroxide reduction. Maximum bleaching of murexide or nitrosodimethylaniline was obtained with glycyl-glycyl-L-histidine. A decrease in the bleaching rates was observed upon addition of SOD or hydroxyl radical scavengers, showing that the hydrogen peroxide/Ni(II)/glycyl-glycyl-L-histidine system generated superoxide anions as well as hydroxyl radicals. In contrast, addition of glycyl-glycyl-L-histidine inhibited the Cu(II) hydrogen peroxide reduction.

When peptides or proteins were exposed to oxygen radicals produced by Ni(II)/glycyl-glycyl-L-histidine catalysis of hydrogen peroxide reduction, the observed effects were similar to those produced by oxygen radicals generated by water radiolysis or by Fe(II) or Cu(II) mediated Fenton-reactions: hydroxylation of phenylalanine, interchange of disulfides, destruction of tryptophans and dityrosine formation.     

Nickel (II) Complexes of Histidyl-Peptides as Fenton-Reaction Catalysts

Addition of histidyl-peptides containing the glycyl-glycyl-L-histidyl sequence stimulated the catalysis of Ni(II) hydrogen peroxide reduction. Maximum bleaching of murexide or nitrosodimethylaniline was obtained with glycyl-glycyl-L-histidine. A decrease in the bleaching rates was observed upon addition of SOD or hydroxyl radical scavengers, showing that the hydrogen peroxide/Ni(II)/glycyl-glycyl-L-histidine system generated superoxide anions as well as hydroxyl radicals. In contrast, addition of glycyl-glycyl-L-histidine inhibited the Cu(II) hydrogen peroxide reduction.

When peptides or proteins were exposed to oxygen radicals produced by Ni(II)/glycyl-glycyl-L-histidine catalysis of hydrogen peroxide reduction, the observed effects were similar to those produced by oxygen radicals generated by water radiolysis or by Fe(II) or Cu(II) mediated Fenton-reactions: hydroxylation of phenylalanine, interchange of disulfides, destruction of tryptophans and dityrosine formation.     

DNA-Cu(II) poly(amine) complex membrane as novel catalytic layer for highly sensitive amperometric determination of hydrogen peroxide

A novel hydrogen peroxide biosensor was fabricated by using a DNA-Cu(II) complex as a novel electrocatalyst for the reduction of hydrogen peroxide (H2O2). A polyion complex (PIC) membrane composed of DNA and poly(allylamine) (PAA) functioned as a support matrix for immobilization of electrocatalytic element-copper ion. The circular dichroism (CD) spectrum of the DNA-Cu(II)/PAA membrane in wet state showed that the DNA exists in B-like form within the membrane. Electrochemical measurements of the DNA-Cu(II)/PAA membrane-modified glassy carbon (GC) electrode revealed that the copper ion embedded in the DNA/PAA layer exhibits good electrochemical behaviors, and the electrochemical rate constant between the immobilized copper ion and the GC electrode surface was estimated to be 26.4 s(-1). The resulting DNA-Cu(II)/PAA/GC electrode showed an excellent electrocatalytic activity for the H2O2 reduction. The sensitivity of the sensor for the determination of H2O2 was affected by the amount of each component, such as copper ion, DNA and PAA in the DNA-Cu(II)/PAA membrane. Effects of applied potential, pH, temperature, ionic strength and buffer concentrations upon the response currents of the sensor were also investigated for an optimum analytical performance. Even in the presence of dissolved oxygen, the sensor exhibited highly sensitive and rapid (response time, less than 5 s) response to H2O2. The steady-state cathodic current responses of the sensor obtained at -0.2 V versus Ag/AgCl in air-saturated 50 mM phosphate buffer (pH 5.0) increased linearly up to 135 microM with the detection limit of 50 nM. Interference by ascorbic acid and uric acid due to the reduction of Cu(II) was effectively cancelled by further modification of outermost layer of polyion complex film. In addition, the sensor exhibited good reproducibility and stability.     

Attachment of gold nanoparticles to glassy carbon electrode and its application for the direct electrochemistry and electrocatalytic behavior of hemoglobin

Gold nanoparticles have been attached onto glassy carbon electrode surface through sulfhydryl-terminated monolayer and characterized by X-ray photoelectron spectroscopy, atomic force microscopy, electrochemical impedance spectroscopy and cyclic voltammetry. The gold nanoparticles-attached glassy carbon electrodes have been applied to the immobilization/adsorption of hemoglobin, with a monolayer surface coverage of about 2.1 x 10(-10) mol cm(-2), and consequently obtained the direct electrochemistry of hemoglobin. Gold nanoparticles, acting as a bridge of electron transfer, can greatly promote the direct electron transfer between hemoglobin and the modified glassy carbon electrode without the aid of any electron mediator. In phosphate buffer solution with pH 6.8, hemoglobin shows a pair of well-defined redox waves with formal potential (E0') of about -0.085 V (versus Ag/AgCl/saturated KCl). The immobilized hemoglobin maintained its biological activity, showing a surface controlled electrode process with the apparent heterogeneous electron transfer rate constant (ks) of 1.05 s(-1) and charge-transfer coefficient (a) of 0.46, and displays the features of a peroxidase in the electrocatalytic reduction of hydrogen peroxide. A potential application of the hemoglobin-immobilized gold nanoparticles modified glassy carbon electrode as a biosensor to monitor hydrogen peroxide has been investigated. The steady-state current response increases linearly with hydrogen peroxide concentration from 2.0 x 10(-6) to 2.4 x 10(-4) M. The detection limit (3sigma) for hydrogen peroxide is 9.1 x 10(-7) M.     

Electrochemiluminescence of luminol at the titanate nanotubes modified glassy carbon electrode

A new strategy for the construction of a sensitive and stable electrochemiluminescent platform based on titanate nanotubes (TNTs) and Nafion composite modified electrode for luminol is described, TNTs contained composite modified electrodes that showed some photocatalytic activity toward luminol electrochemiluminescence emission, and thus could dramatically enhance luminol light emission. This extremely sensitive and stable platform allowed a decrease of the experiment electrochemiluminescence luminol reagent. In addition, in luminol solution at low concentrations, we compared the capabilities of a bare glassy carbon electrode with the TNT composite modified electrode for hydrogen peroxide detection. The results indicated that compared with glassy carbon electrode this platform was extraordinarily sensitive to hydrogen peroxide. Therefore, by combining with an appropriate enzymatic reaction, this platform would be a sensitive matrix for many biomolecules. Copyright © 2013 John Wiley & Sons, Ltd.     

Single-stranded DNA modification by an oligonucleotide-phthalocyanine Fe(II) conjugate: the kinetic features and the process mechanism

Catalytic oxidative modification of a single-stranded DNA with hydrogen peroxide and molecular oxygen in the presence of a conjugate containing an oligonucleotide complementary to the DNA fragment and tetra-4-carboxyphthalocyanine Fe(II) was studied. The conjugate examined was found to be active in the reaction of oxidative DNA cleavage in the presence of hydrogen peroxide, like the earlier studied oligonucleotide conjugates containing metallocomplexes tetra-4-carboxyphthalocyanine Co(II) and 2,4-di-[2-(2-hydroxyethyl)]deuteroporphyrin IX Fe(III) generating active oxygen forms. The new conjugate was more active in the case of oxidation with molecular oxygen. Kinetic features and optimal regimes of DNA oxidation with hydrogen peroxide were found.     

Porphyrins bound to Ru(bpy)2 clusters: electrocatalysis of sulfite

Mono-, di-, tri- and tetra-ruthenated porphyrins derived from phenyl/4-pyridyl mesosubstituted porphyrin and a trans di-ruthenated dipyridyl octaethylporphyrin have been synthesised. Coated on carbon electrodes, they have been tested as a sensor for sulfite using the oxidation wave of the Ru(II)/Ru(III) couples in hydroalcoholic solutions. At least two peripheral Ru are necessary to trigger the catalysis off. No major influence of the central metallic ions has been detected, but the Co (II) is coordinated by the sulfite.     

Activity and stability of pyrolyzed iron ethylenediaminetetraacetic acid as cathode catalyst in microbial fuel cells

A low-cost and effective iron-chelated catalyst was developed as an electrocatalyst for the oxygen reduction reaction (ORR) in microbial fuel cells (MFCs). The catalyst was prepared by pyrolyzing carbon mixed iron-chelated ethylenediaminetetraacetic acid (PFeEDTA/C) in an argon atmosphere. Cyclic voltammetry measurements showed that PFeEDTA/C had a high catalytic activity for ORR. The MFC with a PFeEDTA/C cathode produced a maximum power density of 1122 mW/m², which was close to that with a Pt/C cathode (1166 mW/m²). The PFeEDTA/C was stable during an operation period of 31 days. Based on X-ray diffraction and X-ray photoelectron spectroscopy measurements, quaternary-N modified with iron might be the active site for the oxygen reduction reaction. The total cost of a PFeEDTA/C catalyst was much lower than that of a Pt catalyst. Thus, PFeEDTA/C can be a good alternative to Pt in MFC practical applications.     

Photoinduced reduction of water by tin(IV) and ruthenium(II) porphyrins

In the paper are presented new photoredox systems for the reduction of water in which water- soluble Sn(IV) and Ru(II) porphyrins have been used as photosensitizers It has been found that during the photolysis of water Sn(IV) porphyrin underwent photoreduction whereas Ru(II) porphyrin underwent photooxidation. The successive photo- products of Sn(IV) porphyrin in the reaction from EDTA were, first, Sn(IV) chlorin and, second, Sn(IV) bacteriochlorin. In the experiments on the photo- generation of hydrogen, a correlation between the rates of hydrogen evolution and the reduction potentials of the electron carriers has been observed. The highest rate of hydrogen generation by means of Sn(IV) and Ru(II) porphyrins has been found for those electron carriers whose values of reduction potentials were tau; 0.55 and tau; 0.45 V. In the case of Ru(II) porphyrin, the rate of hydrogen evolution additionally depended on the molecular structure of the electron carrier. It has been found that during the water photolysis, viologens show a tendency to form their respective complexes with Ru(II) porphyrin, but only when they occur in a one-electron reduced form in the solution.     

Synthesis, characterization and electrode adsorption studies of porphyrins coordinated to ruthenium(II) polypyridyl complexes

Two new porphyrins, meso-tris-3,4-dimethoxyphenyl-mono-(4-pyridyl)porphyrin (H₂MPy3,4DMPP) and meso-tris-3-methoxy-4-hydroxyphenyl-mono-(4-pyridyl)porphyrin (H₂MPy3M4HPP), and their ruthenium analogs obtained by coordination of [Ru(bpy)₂Cl]⁺ groups (where bpy = 2,2′-bipyridine) to the pyridyl nitrogens have been synthesized and studied by electronic absorption spectroscopy, cyclic voltammetry and spectroelectrochemistry. These ruthenated porphyrins couple Ru chromophores to porphyrins containing electroactive meso-substituents. The highest energy electronic absorption for the ruthenated complexes is assigned as a bpy(π) → bpy(π*) intraligand charge transfer while the next lowest energy electronic absorption is assigned as Ru(dπ) → bpy(π*) metal-to-ligand charge transfer (MLCT) transition. The Ru^III/II couples occur at approximately 0.95 V versus the SHE reference electrode in acetonitrile solutions. The first oxidation of the porphyrin is localized on the 3,4-dimethoxyphenyl and 3-methoxy-4-hydroxyphenyl substituents, respectively. Electroactive surfaces result from adsorption of these compounds onto glassy carbon electrodes followed by anodic cycling in acidic media.     

A comparison of cobalt(II) and iron(II) hydroxyl and superoxide free radical formation

We have employed the electron spin resonance spin-trapping technique to study the reaction of Co(II) with hydrogen peroxide in a chemical system and in a microsomal system. In both cases, we employed the spin trap 5,5-dimethyl-1-pyrroline N-oxide (DMPO) and were able to detect the formation of DMPO/.OH and DMPO/.OOH. DMPO/.OOH was the predominant radical adduct formed in the chemical system, while the two adducts were of similar concentrations in the microsomal system. The formation of both of these adducts in either reaction system was inhibited by the addition of superoxide dismutase or catalase, and by chelating the cobalt with either ethylenediaminetetraacetic acid (EDTA) or diethylenetriaminepentaacetic acid (DTPA). The incorporation of the hydroxyl radical scavengers ethanol, formate, benzoate, or mannitol inhibited the formation of DMPO/.OH in both systems. We also repeated the study using Fe(II) in place of Co(II). In contrast to the Co(II) results, Fe(II) reacted with hydrogen peroxide to yield only DMPO/.OH, and this adduct formation was relatively insensitive to the presence of added superoxide dismutase. In addition, Fe(II)-mediated DMPO/.OH formation increased when the iron was chelated to either EDTA or DTPA rather than being inhibited as for Co(II). Thus, we propose that Co(II) does not react with hydrogen peroxide by the classical Fenton reaction at physiological pH values.     

The stability of DNA-porphyrin complexes in the presence of Mn(II) ions

The complex formation of porphyrins with DNA leads to changes of stability of DNA. In the present study we investigated binding properties and the thermodynamic parameters of a water-soluble, cationic planar Cu(II)-containing meso-tetrakis(4-N-butyl-pyridiniumyl)porphyrin [CuTButPyP4] and nonplanar Co(II)-containing meso-tetrakis(4-N-butyl-pyridiniumyl)porphyrin [CoButPyP4] with calf thymus DNA in the presence of divalent manganese ions. For displaying the changes of thermodynamic parameters (T_m and ΔT) the melting curves of DNA-porphyrin complexes in the presence of Mn²⁺ ions have been obtained. The enthalpy (ΔH) of helix-coil transition has been also evaluated. It was shown that the binding of ions to DNA proceeds in two stages depending on the manganese/DNA phosphates molar ratio [Mn]/[P]. At the first stage (0.001 < [Mn]/[P] < 1), the interaction of manganese ions with DNA phosphates occurs, causing an additional screening of their negative charge and the stabilization of the double helix. As a result, the best conditions for intercalation of CuTButPyP4 or of peripheral rings of CoButPyP4 occur. The significant increase of T_m, but less changes of ΔT were observed. At the second stage (1 < [Mn]/[P] < 4), the ions interact with both the phosphates and the nitrogen bases of DNA. At this stage, it is possible for the manganese ion to coordinate simultaneously to the oxygen atom of the phosphate and the neighboring base of DNA. At a higher [Mn]/[P] ratio, the destabilization of the double helix begins, and partial breakage of the hydrogen bonds between the nitrogen bases occurs. Respectively the destabilization of DNA in the presence of both porphyrins takes place.     

Tris-ruthenium(II)/copper(II) multimetallic porphyrin: Synthesis, characterization, DNA binding and supercoiled DNA photocleavage studies

The porphyrin, meso-5-(pentafluorophenyl)-10, 15, 20-tris(4-pyridyl)porphyrin has been used to synthesize two new metalloporphyrin complexes. Insertion of copper(II) into the porphyrin center gives the copper(II) porphyrin. Coordination of three [Ru(bipy)₂Cl]⁺ moieties (where bipy = 2,2′-bipyridine) to the pyridyl nitrogens of the copper(II) porphyrin gives the target complex. Electronic transitions associated with the copper(II) porphyrin and the triruthenium copper(II) porphyrin include an intense Soret band and a less intense Q-band in the visible region of the spectrum. An intense π-π∗ transition in the UV region associated with the bipyridyl groups and a metal to ligand charge transfer (MLCT) band appearing as a shoulder to the Soret band are observed for the ruthenated copper(II) porphyrin. Electrochemical properties associated with the multimetallic complex include a redox couple in the cathodic region with E_1/2 = −0.86 V versus Ag/AgCl attributed to the porphyrin and a redox couple in the anodic region E_1/2 = 0.88 V versus Ag/AgCl due to the Ru^III/II couple. DNA titrations indicate the triruthenium copper(II) porphyrin interacts with DNA potentially through a groove binding mechanism. Irradiation of aqueous solutions of the target complex and supercoiled DNA at a 10:1 base pair to complex ratio with visible light above 400 nm indicates that the complex causes nicking of the DNA helix.     

Sensor and biosensor based on Prussian Blue modified gold and platinum screen printed electrodes

Gold (Au) and platinum (Pt) screen-printed electrodes were modified with Prussian Blue (PB) for the development of amperometric sensors selective for hydrogen peroxide detection. The sensors exhibited sensitivities towards H(2)O(2) equal to 2 A M(-1) cm(-2) for Au and 1 A M(-1) cm(-2) for Pt electrodes. The sensors were also employed as the basis for construction of glucose biosensors through further modification with crystallised glucose oxidase immobilised in a Nafion membrane. In order to improve the operational stability of the modified electrodes a buffer solution containing tetrabutylammonium toluene-4-sulfonate was used. The long-term performance of the sensors and biosensors were evaluated by continuous monitoring of hydrogen peroxide and glucose solutions (50 microM and 1 mM, respectively) in the flow-injection mode for 10 h.     

Adsorption of molecular oxygen by polymer covalently bonded co(II) porhyrin complex in toluene

Reaction betwenn molecular oxygen and polystyrene covalently bonded Co(II) protoporphyrin IX complex, which was prepaired by the incorporation of a cobaltous ion into the metal-free porphyrin polymer, was studied in the presence of N-ethylimidazole by measuring visible absorption and electron spin resonance spectra. It was found that the complex forms a monomeric oxygen adduct reversibly at low temperature dependent on oxygen pressure. In the presence of molecular oxygen, a new electron spin resonance signal due to the oxygen complex at g_iso=2.02 shows no superhyperfine splitting structure in fluid toluene solution even at ?80 °C, but it was observed in frozen toulene glass solution at ?120°C, The oxygen adducts of the complexes between C0(II) protoporphyrin IX dimethyl ester and N-ethylimidazole and copoly(styrene-N-vinylimidazole) showed eight resolved superhyperfine splitting at ?40 and ?60°C, respectively. The polymer covalently bonded Co(II) complex with N-ethylimidazole was oxidized at room temperature under oxygen atmosphere. It was suggested that a Co(II) porphyrin–oxygen adduct with an axial ligand may be oxidised monomolecularly at high temperature.     

Simultaneous determination of catecholamines, uric acid and ascorbic acid at physiological levels using poly(N-methylpyrrole)/Pd-nanoclusters sensor

An interesting electrochemical sensor has been constructed by the electrodeposition of palladium nanoclusters (Pd_nano) on poly(N-methylpyrrole) (PMPy) film-coated platinum (Pt) electrode. Cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and scanning electron microscopy were used to characterize the properties of the modified electrode. It was demonstrated that the electroactivity of the modified electrode depends strongly on the electrosynthesis conditions of the PMPy film and Pd_nano. Moreover, the modified electrode exhibits strong electrocatalytic activity toward the oxidation of a mixture of dopamine (DA), ascorbic acid (AA), and uric acid (UA) with obvious reduction of overpotentials. The simultaneous analysis of this mixture at conventional (Pt, gold [Au], and glassy carbon) electrodes usually struggles. However, three well-resolved oxidation peaks for AA, DA, and UA with large peak separations allow this modified electrode to individually or simultaneously analyze AA, DA, and UA by using differential pulse voltammetry (DPV) with good stability, sensitivity, and selectivity. This sensor is also ideal for the simultaneous analysis of AA, UA and either of epinephrine (E), norepinephrine (NE) or l-DOPA. Additionally, the sensor shows strong electrocatalytic activity towards acetaminophen (ACOP) and other organic compounds. The calibration curves for AA, DA, and UA were obtained in the ranges of 0.05 to 1 mM, 0.1 to 10 μM, and 0.5 to 20 μM, respectively. The detection limits (signal/noise [S/N] = 3) were 7 μM, 12 nM, and 27 nM for AA, DA, and UA, respectively. The practical application of the modified electrode was demonstrated by measuring the concentrations of AA, DA, and UA in injection sample, human serum, and human urine samples, respectively, with satisfactory results. The reliability and stability of the modified electrode gave a good possibility for applying the technique to routine analysis of AA, DA, and UA in clinical tests.     

Synthesis, characterization and biological activity evaluation of Pt(II), Pd(II), Co(III) and Ni(II) complexes with N-heteroaromatic selenosemicarbazones

Five new complexes of Pt(II), Pd(II), Co(III) and Ni(II) with 2-pyridine(quinoline)carboxaldehyde selenosemicarbazones were synthesized and characterized. Crystal structures of Pt(II) complex with the pyridine derivative and Co(III) complex with the quinoline derivative were determined. In all complexes the ligands were coordinated through N₂Se donor atom set forming either square-planar (Pt, Pd) or octahedral (Co, Ni) geometry. All complexes showed biological activity.     

Direct electrochemistry and electrocatalytic activity of catalase incorporated onto multiwall carbon nanotubes-modified glassy carbon electrode

The direct voltammetry and electrocatalytic properties of catalase, which was adsorbed on the surface of multiwall carbon nanotubes (MWCNTs), was investigated. A pair of well-defined and nearly reversible cyclic voltammetry peaks for Fe(III)/Fe(II) redox couple of catalase adsorbed on the surface of MWCNTs at approximately -0.05 V versus reference electrode in pH 6.5 buffer solution, indicating the direct electron transfer between catalase and electrode. The surface coverage of catalase immobilized on MWCNTs glassy carbon electrode was approximately 2.4x10(-10) molcm-2. The transfer coefficient (alpha) was calculated to be 0.4, and the heterogeneous electron transfer rate constant was 80 s-1 in pH 7, indicating great facilitation of the electron transfer between catalase and MWCNTs adsorbed on the electrode surface. The formal potential of catalase Fe(III)/Fe(II) couple in MWCNTs film had a linear relationship with pH values between 2 and 11 with a slope of 58 mV/pH, showing that the electron transfer is accompanied by single proton transportation. Catalase adsorbed on MWCNTs exhibits a remarkable electrocatalytic activity toward the reduction of oxygen and hydrogen peroxide. The value for calculated Michaelis-Menten constant (1.70 mM) was high, indicating the potential applicability of the films as a new type of reagentless biosensor based on the direct electrochemistry of the catalase enzyme.