Simple high-performance liquid chromatographic method for the determination of PGT/1A, a new immunostimulating drug, in biological fluids

This paper describes a simple high-performance liquid chromatographic method for the determination of PGT/1A (3- -pyroglutamyl- -thiazolidine-4-carboxylic acid), a new immunostimulating drug, in plasma and urine. The column was packed with LiChrospher-NH₂ (5 μm), the mobile phase was 0.02 M monobasic potassium phosphate (pH 3.2 with concentrated phosphoric acid)—acetonitrile (25:75, v/v), the flow-rate was 1.2 ml/min, the detection wavelength was 210 nm and the apparatus was a Varian Model 5000. Plasma (1 ml) was added to 1.2 ml of acetonitrile and the supernatant injected; the urine was diluted 1:5. The retention time of PGT/1A was 9.4 min in plasma and 9.9 min in urine. The method was validated for recovery, accuracy and reproducibility. The results after intravenous injection in twelve volunteers are also given.     

Determination of risperidone and its major metabolite 9-hydroxyrisperidone in human plasma by reversed-phase liquid chromatography with ultraviolet detection

A simple and sensitive high-performance liquid chromatographic (HPLC) method with UV absorbance detection is described for the quantitation of risperidone and its major metabolite 9-hydroxyrisperidone in human plasma, using clozapine as internal standard. After sample alkalinization with 1 ml of NaOH (2 M) the test compounds were extracted from plasma using diisopropyl ether–isoamylalcohol (99:1, v/v). The organic phase was back-extracted with 150 μl potassium phosphate (0.1 M, pH 2.2) and 60 μl of the acid solution was injected into a C₁₈ BDS Hypersil analytical column (3 μm, 100×4.6 mm I.D.). The mobile phase consisted of phosphate buffer (0.05 M, pH 3.7 with 25% H₃PO₄)–acetonitrile (70:30, v/v), and was delivered at a flow-rate of 1.0 ml/min. The peaks were detected using a UV detector set at 278 nm and the total time for a chromatographic separation was about 4 min. The method was validated for the concentration range 5–100 ng/ml. Mean recoveries were 98.0% for risperidone and 83.5% for 9-hydroxyrisperidone. Intra- and inter-day relative standard deviations were less than 11% for both compounds, while accuracy, expressed as percent error, ranged from 1.6 to 25%. The limit of quantitation was 2 ng/ml for both analytes. The method shows good specificity with respect to commonly prescribed psychotropic drugs, and it has successfully been applied for pharmacokinetic studies and therapeutic drug monitoring.     

Flow‐injection chemiluminescence method to detect a β2 adrenergic agonist

A new method for the detection of β₂ adrenergic agonists was developed based on the chemiluminescence (CL) reaction of β₂ adrenergic agonist with potassium ferricyanide–luminol CL. The effect of β₂ adrenergic agonists including isoprenaline hydrochloride, salbutamol sulfate, terbutaline sulfate and ractopamine on the CL intensity of potassium ferricyanide–luminol was discovered. Detection of the β₂ adrenergic agonist was carried out in a flow system. Using uniform design experimentation, the influence factors of CL were optimized. The optimal experimental conditions were 1 mmol/L of potassium ferricyanide, 10 µmol/L of luminol, 1.2 mmol/L of sodium hydroxide, a flow speed of 2.6 mL/min and a distance of 1.2 cm from ‘Y₂’ to the flow cell. The linear ranges and limit of detection were 10–100 and 5 ng/mL for isoprenaline hydrochloride, 20–100 and 5 ng/mL for salbutamol sulfate, 8–200 and 1 ng/mL for terbutaline sulfate, 20–100 and 4 ng/mL for ractopamine, respectively. The proposed method allowed 200 injections/h with excellent repeatability and precision. It was successfully applied to the determination of three β₂ adrenergic agonists in commercial pharmaceutical formulations with recoveries in the range of 96.8–98.5%. The possible CL reaction mechanism of potassium ferricyanide–luminol–β₂ adrenergic agonist was discussed from the UV/vis spectra. Copyright © 2014 John Wiley & Sons, Ltd.     

Sensitive reversed-phase high-performance liquid chromatographic method for the determination of atevirdine and its N-desethyl metabolite in human saliva or cerebrospinal fluid using solid-phase extraction

A sensitive reversed-phase high-performance liquid chromatographic method for the determination of atevirdine and its primary metabolite in human saliva or cerebrospinal fluid using solid-phase extraction is described. Samples mixed with internal standard and sodium phosphate buffer were applied to an activated C₁₈ solid-phase extraction column. The reconstituted eluate was injected onto a Zorbax RX C₈ column utilizing a mobile phase of 100 mM ammonium acetate (pH 4.0)–isopropyl alcohol–acetonitrile (55:20:25, v/v/v). Fluorescence detection was employed with excitation at 295 nm and emission at 456 nm. Quantitation was achieved using peak-height ratios. The detection response curve was linear from 2 to 850 nM for atevirdine in both human saliva and cerebrospinal fluid and from 2 to 250 nM for the metabolite in human saliva. The method was utilized to analyze cerebrospinal fluid and saliva samples from clinical studies.     

Determination of azosemide and its metabolite in plasma, blood, urine and tissue homogenates by high-performance liquid chromatography

High-performance liquid chromatographic methods were developed for the determination of azosemide and its metabolite, M1, in human plasma and urine and rabbit blood and tissue homogenates. The methods involved deproteinization of the biological samples: 2.5 volumes of acetonitrile were used for the determination of azosemide and 1 volume of saturated Ba(OH)₂ and ZnSO₄ for that of M1. A 50-μl aliquot of the supernatant was injected onto a C₁₈ reversed-phase column in each instance. The mobile phases employed were 0.03 M phosphoric acid—acetonitrile (50:40, v/v) for azosemide and 0.03 M phosphoric acid/0.2 M acetic acid—acetonitrile (83:17, v/v) for M1. The flow-rate was 1.5 ml/min in both instances. The column effluent was monitored by ultraviolet detection at 240 and 236 nm for azosemide and M1, respectively. The retention times for azosemide and M1 were 6.0 and 8.3 min, respectively. The detection limits for both azosemide and M1 in both human plasma and urine were 50 ng/ml. The coefficients of variation of the assay were generally low (below 11.0%) for plasma, urine, blood and tissue homogenates. No interferences from endogenous substances or other diuretics tested were observed.     

Estimation of amniotic fluid phospholipids by high-performance liquid chromatography

We have developed a high-performance liquid chromatographic (HPLC) method for the analyses of surface-active amniotic fluid phospholipids, lecithin (L), sphingomyelin (S), phosphatidyl glycerol (PG), phosphatidyl inositol (PI), phosphatidyl ethanolamine (PE), and phosphatidyl serine (PS), which are important in the prediction of fetal lung maturity. The method incorporates an internal standard in the amniotic fluid extract, and utilizes a 10-μl aliquot of a 2:1 chloroform—methanol extract of amniotic fluid injected onto a 5-μm DIOL or CN HPLC column, and a variable-wavelength detector set at 203 nm.Amniotic fluid phospholipid estimations were determined on 40 amniotic fluid samples by the HPLC method and by the routine thin-layer chromatographic (TLC) method. Good agreement was observed between the two methods for the L/S ratio, PG, and PI (r_PG 0.94, r_PI 0.95, r_L/S 0.97).The advantages of the HPLC procedure include: (i) Selective separation for PG, PI, PS, and PE, as well as L and S at the same time. (ii) The internal standard allows individual concentration of phospholipids to be estimated. (iii) The procedure is rapid: 16 min for a single assay compared with 50 min for the standard TLC procedure.     

Sensitive isocratic liquid chromatographic assay for the determination of 5, 10, 15, 20-tetra(m-hydroxyphenyl)chlorin in plasma and tissue with electrochemical detection

A simple extraction procedure and a sensitive high-performance liquid chromatographic (HPLC) method are described for the determination of the photodynamic therapeutic agent 5, 10, 15, 20-tetra(m-hydroxyphenyl)chlorin (mTHPC) in plasma and tumour tissue. Reversed-phase high-performance liquid chromatography was performed on a C₁₈ column (70×4.6 mm I.D.) with a mobile phase of 0.01 M potassium dihydrogenphosphate buffer, pH 2.5-acetonitrile (55:45, v/v) and a coulometric detection (+0.80 V). The mean recoveries of mTHPC in the concentration ranges (5–2000 and 10–1000 ng/ml) were 90 and 89% for plasma and tumour samples, respectively. The procedure for plasma and tissue preparation involved solvent precipitation using methanol combined with ammonia solution and dimethyl sulphoxide (4, 0.2, 0.1, v/v/v) and (2, 0.1, 0.1, v/v/v) for plasma and tissue, respectively. For mTHPC at concentrations ranging from 5 to 2000 ng/ml, the within-day relative standard deviations, based on triplicate determinations were less than 8% and the between-day relative standard deviations calculated by performing extraction procedure of plasma samples on three different days ranged from 3 to 18%. This highly sensitive method, 5 and 10 ng/ml for plasma and tissue respectively, was applied successfully to the determination of mTHPC in mouse tumours for pharmacokinetic studies.     

High-performance liquid chromatographic measurement of urocanic acid isomers and their ratios in naturally light-exposed skin and naturally shielded skin

We have developed methods for sampling and extraction of trans-urocanic acid and cis-urocanic acid from human skin, and subsequent high-performance liquid chromatographic measurement of these isomers. Sampling involves applying cellophane adhesive tape to the skin for 10 s. Urocanic acid isomers were completely extracted by immersing the tape in KOH solution. The HPLC column was a Tosoh ODS 80_TS (250×4.6 mm I.D., 7 μm average particle size) eluted with 20 mM potassium dihydrogenphosphate containing 1 g/l sodium heptanesulphonate (pH 3.7)–acetonitrile (93:7, v/v) at a flow-rate of 1.0 ml/min. The isomers were detected by UV absorbance at 264 nm. This technique was used to analyze the ratio of trans-urocanic acid/cis-urocanic acid on human skin at various sites on the body. It was found that the ratio was low in naturally light-exposed skin and high in naturally shielded skin.     

Determination of maprotiline in plasma by high-performance liquid chromatography with chemiluminescence detection

A simple and sensitive high-performance liquid chromatographic method is described for the determination of maprotiline, an antidepressant, in plasma. After a single-step extraction from plasma (100 μl) with n-hexaneisoamylalcohol (19:1, v/v), the drug and desipramine (internal standard) are converted into their chemiluminescent derivatives by reaction with 6-isothiocyanatobenzo[g]phthalazine-1,4(2H,3H)-dione, a new chemiluminescence derivatization reagent for amines. The derivatives are separated within 60 min on a reversed-phase column, TSKgel ODS-80, using isocratic elution with acetonitrile-100 mM acetate buffer (pH 3.2), and produced chemiluminescence by reaction with hydrogen peroxide in the presence of potassium hexacyanoferrate(III) in alkaline medium. The detection limit for maprotiline added to plasma is 0.36 pmol (0.1 ng)/ml plasma (1.5 fmol on column), at a signal-to-noise ratio of 3.     

Microbore high-performance liquid chromatographic determination of cisapride in rat serum samples using column switching

For the determination of cisapride from serum samples, an automated microbore high-performance liquid chromatographic method with column switching has been developed. After serum samples (100 μl) were directly injected onto a Capcell Pak MF Ph-1 pre-column (10×4 mm I.D.), the deproteinization and concentration were carried out by acetonitrile–phosphate buffer (20 mM, pH 7.0) (2:8, v/v) at valve position A. At 2.6 min, the valve was switched to position B and the concentrated analytes were transferred from MF Ph-1 pre-column to a C₁₈ intermediate column (35×2 mm I.D.) using washing solvent. By valve switching to position A at 4.3 min, the analytes were separated on a Capcell Pak C₁₈ UG 120 column (250×1.5 mm I.D.) with acetonitrile–phosphate buffer (20 mM, pH 7.0) (5:5, v/v) at a flow-rate of 0.1 ml/min. Total analysis time per sample was 18 min. The linearity of response was good (r=0.999) over the concentration range of 5–200 ng/ml. The within-day and day-to-day precision (CV) and inaccuracy were less than 3.7% and 3.8%, respectively. The mean recovery was 96.5±2.4% with the detection limit of 2 ng/ml.     

The tissue distribution in mice and pharmacokinetics in rabbits of oxaliplatin liposome

A rapid, sensitive, and simple high-performance liquid chromatographic (HPLC) method with an ultraviolet detector (UV) has been developed for the determination of oxaliplatin in the plasma of rabbits and tissues of mice. The sample preparation was carried out by complexation with 0.5?mL of DETC (diethyl-dithiocarbamate) solution and extracted by ether and chloroform. Then, 20?μL of supernatant was injected into the HPLC system with 0.25?mol/L of sodium chloride solution and methanol (30:70 v/v) as the mobile phase at a flow rate of 1.0?mL/min. Separation was performed with a C₁₈ column at 25°C. The peak was detected at 254?nm. The calibration curve was linear (R²?≥?0.9995) in the concentration range of 0.1~200?μg/mL in plasma and tissues. The intra- and interday variation coefficients were not more than 2.61 and 3.83%, respectively. The limit of detection was 20?ng/mL. The mean recoveries of oxaliplatin were ranged from 97.83 to 104.17% in plasma and tissues. The present method has been successfully applied to the pharmacokinetic study of oxaliplatin liposome in mice and rabbits.     

Purification of human brain metallothionein by organic and reversed-phase high-performance liquid chromatography under acidic conditions

A simplified high-performance liquid chromatographic method for the detection of metallothioneins, notably metallothionein-III, has been developed. In order to purify metallothionein, differential acetone precipitation at 50% (v/v) and at 80% (v/v) was employed on a 20% normal human brain homogenate. The reconstituted pellet was injected into a C₁₈ microbore reversed-phase HPLC column, equilibrated with 0.1% trifluoroacetic acid, and developed at a flow-rate of 800 μl/min with a linear gradient from 0% to 60% acetonitrile in 0.094% trifluoroacetic acid for 60 min. Western blots indicated that metallothioneins-I and II eluted at 16% acetonitrile and metallothionein-III eluted at 37% acetonitrile.     

High-performance liquid chromatographic determination of sotalol in biological fluids

A sensitive, selective and reproducible reversed-phase high-performance liquid chromatographic method is described for the quantification of sotalol in human serum and urine. Sotalol and the internal standard, atenolol, were extracted from alkalinized serum and urine (pH 9.0) into 1-butanol—chloroform (20:60, v/v). The organic phase was evaporated, and to the residue was added 0.1 M sulphuric acid (serum analysis) or mobile phase (urie analysis). The mobile phase consisted of 0.01 M phosphate buffer (pH 3.2) and acetonitrile (20:80, v/v) containing 3 mM n-octylsodium sulphate. The flow-rate was 1.5 ml/min. The retention times of atenolol and sotalol were 7 and 10 min, respectively. Ultraviolet detection at 226 nm made it possible to achieve a detection limit of 0.03 μmol/l.     

Reversed-phase high-performance liquid chromatography of nicotinic acid mononucleotide for measurement of quinolinate phosphoribosyltransferase

A system has been developed for the determination of quinolinate phosphoribosyltransferase (QPRT) activity in liver and kidney homogenates using HPLC. A product, nicotinic acid mononucleotide (NaMN), is separated by reversed-phase chromatography (a Tosoh ODS 80TS was used as an analytical column) using a mixture of 10 mM KH₂PO₄–K₂HPO₄ buffer (pH 7.0) containing 1.48 g/l tetra-n-butylammonium bromide–acetonitrile (9:1, v/v) as a mobile phase. The flow-rate was 1.0 ml/min, the detection wavelength was 265 nm. The column temperature was maintained at 40°C. Under these conditions, NaMN was eluted at about 8.1 min. Sample preparation was very straightforward. The reaction mixture of QPRT assay was stopped by immersing the tube into a boiling water bath, the resulting supernatant was filtered, and the filtrate was directly injected into a HPLC system. The total HPLC analysis time was approximately 20 min.     

A convenient manual trinitrobenzenesulfonic acid method for monitoring amino acids and peptides in chromatographic column effluents.

The trinitrobenzenesulfonic acid (TNBS) method of R. Fields (1971, Biochem. J., 124, 581–590) has been modified for the manual detection of amino acids and peptides in chromatographic column effluent by changing the reaction conditions to 1 mm TNBS in 0.4 m potassium borate buffer, pH 9.2, at room temperature for 30 to 50 min. The reaction with amines and the spontaneous hydrolysis of TNBS are stopped by neutralization to pH 6.25 with sodium monobasic phosphate (0.33 m). Sodium sulfite (3 mm) is added to increase the absorptivity of the product. The TNBS reagent blank is less than 0.100 A₄₂₀ after 50 min of reaction. Since the ΔA₄₂₀ of the reagent blank is ～0.002/min before quenching the reaction, and zero afterward, the time required for reaction and for absorbance measurements need not be controlled precisely. Alkaline hydrolysis of peptides is carried out prior to detection to increase the sensitivity of the method. This procedure is convenient for the manual determination of 5 to 100 nmol of amino acids in the 50–100 samples required to define a chromatographic elution profile.     

Determination of cycloserine in human plasma by high-performance liquid chromatography with fluorescence detection,using derivatization with p-benzoquinone

A new method for determining cycloserine in plasma samples is described. This method is based on the derivatization of cycloserine with p-benzoquinone, a reaction that takes place at the same time as the process of plasma deproteinization due to the presence of ethanol as solvent in the solution of the derivatization reagent. Four derivatives are obtained from this reaction. The main derivative is well correlated with the cycloserine concentration. The ratio between the volumes of the plasma sample and the reagent solution is 1:2 for a p-benzoquinone concentration of 1000 μg/mL. Elution from a C₁₈ column was isocratic, using a mobile phase containing (v/v) 85% aqueous 0.1% formic acid solution, and 15% (v/v) of a mixture of methanol and acetonitrile (1:1), with a flow-rate of 1 mL/min, at 25°C. Determinations by fluorescence detection were achieved with excitation at 381 nm and emission at 450 nm, with a detection limit of 10 ng/mL for an injection volume of 5 μL. This method was validated and applied to the determination of cycloserine in blood plasma samples of several healthy volunteers.     

Measurement and pharmacokinetic analysis of unbound ceftazidime in rat blood using microdialysis and microbore liquid chromatography

To evaluate the biodisposition of ceftazidime in rat blood, a rapid and simple microbore liquid chromatographic technique together with a microdialysis sampling technique were developed. This method involves an on-line design for blood dialysate directly injected into a microbore liquid chromatographic system. The chromatographic conditions consisted of a mobile phase of methanol–acetonitrile–100 mM monosodium phosphoric acid (pH 3.0) (10:10:80, v/v/v) pumped through a microbore reversed-phase column at a flow-rate of 0.05 ml/min. With the detection wavelength set at 254 nm, a good linear correlation was observed between the peak area and the ceftazidime concentration at 0.1 to 50 μg/ml (r=0.999). Microdialysis probes, being custom-made, were screened for acceptable in vivo recovery while chromatographic resolution and detection were validated for response linearity, as well as intra-day and inter-day variabilities. This method was then applied to the pharmacokinetic profiling of ceftazidime in blood following intravenous 50 mg/kg administration to rats. The pharmacokinetics was calculated from the corrected data for dialysate concentrations of ceftazidime versus time. This method has been used to study ceftazidime pharmacokinetics in rats and has proven to be rapid and reproducible.     

Determination of urinary nucleosides by direct injection and coupled-column high-performance liquid chromatography

A coupled-column liquid chromatographic method for the direct analysis of 14 urinary nucleosides is described. Efficient on-line clean-up and concentration of 14 nucleosides from urine samples were obtained by using a boronic acid-substituted silica column (40 mm x 4.0 mm I.D.) as the first column (Col-1) and a Hypersil ODS2 column (250 mm x 4.6 mm I.D.) as the second column (Col-2). The mobile phases applied consisted of 0.25 mol/L ammonium acetate (pH 8.5) on Col-1, and of 25 mmol/L potassium dihydrogen phosphate (pH 4.5) on Col-2, respectively. Determination of urinary nucleosides was performed on Col-2 column by using a linear gradient elution comprising 25 mmol/L potassium dihydrogen phosphate (pH 4.5) and methanol-water (60:40, v/v) with UV detection at 260 nm. Urinary nucleosides analysis can be carried out by this procedure in 50 min requiring only pH adjustment and the protein precipitation by centrifugation of urine samples. Calibration plots of 14 standard nucleosides showed excellent linearity (r > 0.995) and the limits of detection were at micromolar levels. Both of intra- and inter-day precisions of the method were better than 6.6% for direct determination of 14 nucleosides. The validated method was applied to quantify 14 nucleosides in 20 normal urines to establish reference ranges.     

Method development in liquid chromatography with a charged cyclodextrin additive for chiral resolution of rac-amlodipine utilising a central composite design

A negatively charged derivative of β-cyclodextrin, sulphobutyl ether-β-cyclodextrin (SBE-β-CD), was examined as a chiral mobile phase additive in reversed-phase high-performance liquid chromatography for the enantiomeric resolution of the calcium channel blocker rac-amlodipine. Theoretical and practical aspects are discussed for setting up a central composite design applicable to any analytical method. These include the correct location of factor points for maintaining orthogonality within the design and the augmentation of centrepoint experiments to allow a larger factor space by increasing the distance of axial star points. Optimised separation was achieved using a reverse-phase column with eluent comprising: acetonitrile (ACN)—potassium dihydrogen phosphate (pH 3.93) containing 2.66 mM SBE-bgr;-CD (26.5:73.5% v/v) at a flow rate of 1.0 ml/min. This yielded a Kaiser peak separation index, P_i = 0.96, at t_R2 = 52 min with satisfactory reproducibility, relative standard deviation values: t_R1, 0.39%; t_R2, 0.47% (n = 5). These experimental results were in excellent agreement with those predicted by the SAS software package for a chromatographic response function model. Multiple regression analysis in four dimensions, with three response models based on R_s, P_i, and a function of P_i, produced response surfaces which revealed zones of optimum robustness and illustrated the interactions involved between the key chromatographic factors. Putative proposals for a mechanism involving the interaction of each of the positively charged enantiomers with the negatively charged cyclodextrin are also discussed. These examine the possibility of ion-pairing and inclusion phenomena to account for the excellent resolution observed. © 1996 Wiley-Liss, Inc.     

Determination of cisapride and norcisapride in human plasma using high-performance liquid chromatography with ultraviolet detection

A simple, rapid and reproducible high-performance liquid chromatographic assay for cisapride and norcisapride in human plasma is described. Samples of plasma (150 μl) were extracted using a C₁₈ solid-phase cartridge. Regenerated tubes were eluted with 1.0 ml of methanol, dried, redissolved in 150 μl of methanol and injected. Chromatography was performed at room temperature by pumping acetonitrile–methanol–0.015 M phosphate buffer pH 2.2–2.3 (680:194:126, v/v/v) at 0.8 ml/min through a C₁₈ reversed-phase column. Cisapride, norcisapride and internal standard were detected by absorbance at 276 nm and were eluted at 4.3, 5.3 and 8.1 min, respectively. Calibration plots in plasma were linear (r>0.998) from 10 to 150 ng/ml. Intraday precisions for cisapride and norcisapride were 3.3% and 5.4%, respectively. Interday precisions for cisapride and norcisapride were 9.6% and 9.0%, respectively. Drugs used which might be coadministered were tested for interference.